Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

IBS simulation with different RF configurations in RHIC

It is a crucial task to understand the beam emittance growth during RHIC cycle and the underlying causes. One would benefit not just for the current operation of RHIC, also for the design of eRHIC. This report focuses on the Intra-Beam Scattering (IBS) contribution to the emittance growth of the proton beam with two different configurations of RF system. The answers to these questions will be given in the end of the report; can IBS explain the emittance growth all alone? What’s the difference of IBS growth rates for different RF configurations?

43 PARTICLE ACCELERATORS↗

RF Reverb Chamber Radio Frequency Reverberation Chamber

Viewing an experiment in the radio frequency (RF) reverberation chamber, also known as a mode stirred chamber. The chamber is an isolated RF test chamber containing an irregularly shaped paddle capable of measuring a device’s radiated emissions, radiated immunity, shielding effectiveness, and antenna efficiency from 500MHz to 18GHz. The chamber is electromagnetically isolated from extremely low frequencies and is highly reverberant, which creates the fundamental wave chaotic properties required to make statistical measurements.

47 OTHER INSTRUMENTATION↗

An All-Optical Microwave Mixer with 8db RF Gain

An all-optical microwave mixer with an 8dB RF gain is demonstrated by using a semiconductor optical amplifier (SOA). 6GHz RF signal on a 1312 nm optical carrier is up-converted and down-converted to 1GHZ and 11 GHz by a 5GHz local oscillation (LO) signal on a 1320 nm optical carrier. Such a carrier could readily extend to millimeter wave range.

microwave mixer fiberoptics fiber optic transmissi↗

Performance of RF Downlink with Periodic Data Frame

Telemetry discrete spectrum components induced by the periodicity of an Attached Sync Marker may coincide with the RF carrier frequency causing unwanted interference while tracking the RF carrier.

pseudo randomizer decrease potential interference ↗

Evidence for Water Ice on the Moon: Results for Anomalous Polar Craters from the LRO Mini-RF Imaging Radar

The Mini-RF radar instrument on the Lunar Reconnaissance Orbiter spacecraft mapped both lunar poles in two different RF wavelengths (complete mapping at 12.6 cm S-band and partial mapping at 4.2 cm X-band) in two look directions, removing much of the ambiguity of previous Earth- and spacecraft-based radar mapping of the Moon's polar regions. The poles are typical highland terrain, showing expected values of radar cross section (albedo) and circular polarization ratio (CPR). Most fresh craters display high values of CPR in and outside the crater rim; the pattern of these CPR distributions is consistent with high levels of wavelength-scale surface roughness associated with the presence of block fields, impact melt flows, and fallback breccia. A different class of polar crater exhibits high CPR only in their interiors, interiors that are both permanently dark and very cold (less than 100 K). Application of scattering models developed previously suggests that these anomalously high-CPR deposits exhibit behavior consistent with the presence of water ice. If this interpretation is correct, then both poles may contain several hundred million tons of water in the form of relatively "clean" ice, all within the upper couple of meters of the lunar surface. The existence of significant water ice deposits enables both long-term human habitation of the Moon and the creation of a permanent cislunar space transportation system based upon the harvest and use of lunar propellant.

Mini-RF radar↗

SRF and RF systems for LEReC Linac

The Low Energy RHIC electron Cooling (LEReC) is under development at BNL to improve RHIC luminosity at low energies. It will consist of a short electron linac and two cooling sections, one for blue and one for yellow rings. For the first stage of the project, LEReC-I, we will install a 704 MHz superconducting RF cavity and three normal conducting cavities operating at 9 MHz, 704 MHz and 2.1 GHz. The SRF cavity will boost the electron beam energy up to 2 MeV. The warm cavities will be used to correct the energy spread introduced in the SRF cavity. The paper describes layouts of the SRF and RF systems, their parameters and status.

43 PARTICLE ACCELERATORS↗

LCLS-II high power RF system overview and progress

A second X-ray free electron laser facility, LCLS-II, will be constructed at SLAC. LCLS-II is based on a 1.3 GHz, 4 GeV, continuous-wave (CW) superconducting linear accelerator, to be installed in the first kilometer of the SLAC tunnel. Multiple types of high power RF (HPRF) sources will be used to power different systems on LCLS-II. The main 1.3 GHz linac will be powered by 280 1.3 GHz, 3.8 kW solid state amplifier (SSA) sources. The normal conducting buncher in the injector will use four more SSAs identical to the linac SSAs but run at 2 kW. Two 185.7 MHz, 60 kW sources will power the photocathode dual-feed RF gun. A third harmonic linac section, included for linearizing the bunch energy spread before the first bunch compressor, will require sixteen 3.9 GHz sources at about 1 kW CW. A description and an update on all the HPRF sources of LCLS-II and their implementation is the subject of this paper.

43 PARTICLE ACCELERATORS↗

Simons Observatory Microwave SQUID Multiplexing Readout: Cryogenic RF Amplifier and Coaxial Chain Design

The Simons Observatory (SO) is an upcoming polarization-sensitive cosmic microwave background experiment on the Cerro Toco Plateau (Chile) with large overlap with other optical and infrared surveys (e.g., DESI, LSST, HSC). To enable the readout of O(10,000) detectors in each of the four telescopes of SO, we will employ the microwave SQUID multiplexing technology. With a targeted multiplexing factor of O(1000), microwave SQUID multiplexing has never been deployed on the scale needed for SO. Here we present the design of the cryogenic coaxial cable and RF component chain that connects room temperature readout electronics to superconducting resonators that are coupled to transition edge sensor bolometers operating at sub-Kelvin temperatures. We describe design considerations including cryogenic RF component selection, system linearity, noise, and thermal power dissipation.

47 OTHER INSTRUMENTATION↗

RF-transpond: A 1D coupled cold plasma wave and plasma transport model for ponderomotive force driven density modification parallel to B

The RF-Transpond code couples a fluid plasma transport solver with a frequency domain cold plasma RF wave solver in a 1D domain parallel to a strong background magnetic field. A ponderomotive force term proportional to parallel gradients in the electric field strength is included in the transport model in order to describe ponderomotive effects in the scrape-off layer (SOL) of fusion plasmas. The transport and wave codes are verified independently and a coupled case corresponding to experimental parameters from the LArge Plasma Device (LAPD) is presented. The density perturbation ratio R n , calculated to describe ponderomotive force driven modifications, is up to 20% for the simulation inputs used.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High energy-storage performance of 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} relaxor ferroelectric thin films prepared by RF magnetron sputtering

Highlights: • High-quality PMN-PT 90/10 RFE thin films were prepared by RF magnetron sputtering. • The maximum discharged density of 31.3 J/cm{sup 3} was obtained in the 750-nm-thick film. • PMN-PT RFE films might be a promising material for energy-storage application. - Abstract: 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} (PMN-PT 90/10) relaxor ferroelectric thin films with different thicknesses were deposited on the LaNiO{sub 3}/Si (100) by the radio-frequency (RF) magnetron sputtering technique. The effects of thickness and deposition temperature on the microstructure, dielectric properties and the energy-storage performance of the thin films were investigated in detail. X-ray diffraction spectra indicated that the thin films had crystallized into a pure perovskite phase with a (100)-preferred orientation after annealed at 700 °C. Moreover, all the PMN-PT 90/10 thin films showed the uniform and crack-free surface microstructure. As a result, a larger recoverable energy density of 31.3 J/cm{sup 3} was achieved in the 750-nm-thick film under 2640 kV/cm at room temperature. Thus, PMN-PT 90/10 relaxor thin films are the promising candidate for energy-storage capacitor application.

36 MATERIALS SCIENCE↗

Effect of Ar ion-beam-assistance and substrate temperature on physical properties of Al-doped ZnO thin films deposited by RF magnetron sputtering

Highlights: • AZO and IAZO (303–473 K) films were grown by RF magnetron sputtering technique. • Ar ion-beam converts its kinetic energy as diffusion energy to the deposited atoms. • Structural evolution relies on diffusion energy imparted to the deposited atoms. • Surface texture densify under the aid of ion-beam and substrate temperature. - Abstract: In this study, pronounced effects of ion-beam-assistance and substrate temperature were revealed by exploring the physical properties of Al-doped ZnO thin films deposited by the RF magnetron sputtering technique. Herein, two measurable parameters, ion-beam discharge current (0.1 A) and substrate temperature (303–473 K) were adopted to regulate the structural changes in Al-doped ZnO films. Specifically, progressive structural changes were achieved based on the addition of Ar ion-beam during the film growth. From XRD analysis, we observed significant structural changes that provided an improvement in the film growth towards c-axis (002) plane. In addition, FESEM and AFM analyses demonstrated excellent surface features with the assisted Ar ion-beam. As a result of this process, we effectively modulated the binding energy of Zn 2p level. Finally, the structural investigation accurately demonstrated that the dependence of assisted ion-beam and substrate temperature linearly related to the superior visible transmittance and reduced band gap.

36 MATERIALS SCIENCE↗

RF design for the TOPGUN photogun: A cryogenic normal conducting copper electron gun

Some recent studies of rf breakdown physics in cryogenic copper X-band accelerating structures have shown a dramatic increase in the operating gradient while maintaining low breakdown rates. The TOPGUN project, a collaboration between UCLA, SLAC, and INFN, will use this improvement in gradient to create an ultra-high brightness cryogenic normal conducting photoinjector [16]. The brightness is expected to be higher by a factor of 25 relative to the LCLS photogun [9]. This improvement in the brightness will lead to increased performance of X-Ray free electron lasers (FELs) and ultrafast electron diffraction devices [16]. Here, we present the rf design for this S-band photogun, which will be a drop-in replacement for the current LCLS photogun.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Staging of RF-accelerating Units in a MEMS-based Ion Accelerator

Multiple Electrostatic Quadrupole Array Linear Accelerators (MEQALACs) provide an opportunity to realize compact radio- frequency (RF) accelerator structures that can deliver very high beam currents. MEQALACs have been previously realized with acceleration gap distances and beam aperture sizes of the order of centimeters. Through advances in Micro-Electro-Mechanical Systems (MEMS) fabrication, MEQALACs can now be scaled down to the sub-millimeter regime and batch processed on wafer substrates. In this paper we show first results from using three RF stages in a compact MEMS-based ion accelerator. The results presented show proof-of-concept with accelerator structures formed from printed circuit boards using a 3 × 3 beamlet arrangement and noble gas ions at 10 keV. We present a simple model to describe the measured results. We also discuss some of the scaling behaviour of a compact MEQALAC. The MEMS-based approach enables a low-cost, highly versatile accelerator covering a wide range of currents (10 μA to 100 mA) and beam energies (100 keV to several MeV). Applications include ion-beam analysis, mass spectrometry, materials processing, and at very high beam powers, plasma heating.

43 PARTICLE ACCELERATORS↗

Machine learning surrogates for ion energy–angle distributions in thermal and RF plasma sheaths

Ion energy–angle distributions (IEADs) at material surfaces are a critical input for plasma–material interaction (PMI) studies in fusion devices, yet they are computationally expensive to obtain using particle-in-cell (PIC) simulations. In this work, we develop a machine learning surrogate based on a deep deconvolutional neural network (DDeCNN) trained on large databases generated with the hPIC2 code. The surrogate is capable of reconstructing IEADs from sheath parameters for both thermal and radio-frequency (RF) plasmas, including cases with multiple ion species. Across thousands of test cases, the model achieves high accuracy, with over 97 % of predictions classified as good or average based on standard error metrics (MAE, MSE, L2). Even in the more challenging RF and multi-species regimes, the surrogate reliably captures the multi-peak structure of PIC results. Once trained, the surrogate produces IEADs in milliseconds on a common workstation, yielding speedups of six to seven orders of magnitude compared with running a full PIC simulation. This computational gain enables dense parameter scans and direct coupling of IEAD predictions with PMI and erosion models on whole-device scales in fusion-relevant conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Harmonic and Subharmonic RF Injection Locking of THz Metasurface Quantum-Cascade VECSEL

Harmonic and subharmonic RF injection locking is demonstrated in a terahertz (THz) quantum-cascade vertical-external-cavity surface-emitting laser (QC-VECSEL). By tuning the RF injection frequency around integer multiples and submultiples of the cavity round-trip frequency, different harmonic and subharmonic orders can be excited in the same device. Modulation-dependent behavior of the device has been studied with recorded lasing spectral broadening and locking bandwidths in each case. In particular, harmonic injection locking results in the observation of harmonic spectra with bandwidths over 200 GHz. A semiclassical Maxwell-density matrix formalism has been applied to interpret QC-VECSEL dynamics, which aligns well with experimental observations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimental observation of RF avalanche gain in GaN‐based PN junction diodes

Radio‐frequency (RF) reflection gain in GaN homojunction p‐n diode structures has been observed experimentally. A vertical p + /n structure grown on a native GaN substrate was used to achieve the high internal electric fields necessary to induce impact ionisation in GaN while minimising the effects of dislocations on the device performance. Amplitude and phase signatures in the measured RF reflection coefficient indicate the onset of impact ionisation within the device, with reflection gain observed at frequencies above 350 MHz. The magnitude of the measured gain is consistent with theoretical estimates of impact ionisation parameters, and the bias dependence of the measured reflection phase response is consistent with avalanche as the gain mechanism.

Fay, P.↗

A post-processing method to simulate the generalized RF sheath boundary condition

For applications of ICRF power in fusion devices, control of RF sheath interactions is of great importance. A sheath boundary condition (SBC) was previously developed to provide an effective surface impedance for the interaction of the RF sheath with the waves. The SBC enables the surface power flux and rectified potential energy available for sputtering to be calculated. For legacy codes which cannot easily implement the SBC, or to speed convergence in codes which do implement it, we consider here an approximate method to simulate SBCs by post-processing results obtained using other, e.g. conducting wall, boundary conditions. The basic approximation is that the modifications resulting from the generalized SBC are driven by a fixed incoming wave which could be either a fast wave or a slow wave. Finally, the method is illustrated in slab geometry and compared with exact numerical solutions; it is shown to work very well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Preparation and characterization of Gd{sub 2}O{sub 3} thin films by RF magnetron sputtering

Gd{sub 2}O{sub 3} films were deposited on to glass substrates held at room temperature using radio frequency (RF) magnetron sputtering, at a RF power of 63 W and argon pressure maintained at 1 Multiplication-Sign 10{sup -2}mbar. The morphology was studied by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The band gaps obtained from optical absorption studies are in the range of 3.4 and 4.02 eV, after annealing in air at 380 Degree-Sign C for 1 hour.

36 MATERIALS SCIENCE↗