Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “QC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Development and application of processing and process control for nano-composite materials for lithium ion batteries (CRADA Final Report)

Oak Ridge National Laboratory and A123 Systems, Inc. collaborated on this project to develop a better understanding, quality control procedures, and safety testing for A123 System’s nanocomposite separator (NCS) technology which is a cell based patented technology and separator. NCS demonstrated excellent performance. x3450 prismatic cells were shown to survive >8000 cycles (1C/2C rate) at room temperature with greater than 80% capacity retention with only NCS present as an alternative to conventional polyolefin. However, for a successful commercialization, the coating conditions required to provide consistent and reliable product had not been optimized and QC techniques for being able to remove defective material before incorporation into a cell had not been developed. The work outlined in this report addresses these latter two points. First, experiments were conducted to understand temperature profiles during the different drying stages of the NCS coating when applied to both anode and cathode. One of the more interesting discoveries of this study was the observation of the large temperature decrease experienced by the wet coating between the end of the infrared (IR) drying stage and the beginning of the exposure to the convection drying oven. This is not a desirable situation as the temperature gradient could have a deleterious effect on coating quality. Based on this and other experimental data a radiative transfer model was developed for IR heating that also included a mass transfer module for drying. This will prove invaluable for battery coating optimization especially where IR drying is being employed. A stress model was also developed that predicts that under certain drying conditions tensile stresses are formed in the coating which could lead to cracking that is sometimes observed after drying is complete. Prediction of under what conditions these stresses form is vital to improving coating quality. In addition to understanding the drying process other parameters such as slurry quality and equipment optimization were examined. Removal of particles and gels by filtering, control of viscosity by %solids and mixing adjustments, removal of trapped gas in the slurry and modification of coater speed and slot die gap were all found to be important for producing uniform and flaw-free coatings. Second, an in-line Hi-Pot testing method has been developed specifically for NCS that will enable detection of coating flaws that could lead to soft or hard electrical shorts within the cell. In this way flawed material can be rejected before incorporation into the cell thus greatly reducing the amount of scrap that is generated. Improved battery safety is an extremely important benefit of NCS. Evaluation of battery safety is usually accomplished by conducting a variety of tests including nail penetration, hot box, over charge, etc. For these tests entire batteries must be built but the resultant temperature and voltage responses reveal little about the breakdown mechanism. In this report is described a pinch test which is used to evaluate NCS quality at various stages including coated anode and cathode as well as assembled cell. Coupled with post-microscopic examination of the damaged ‘pinch point’ test data can assist in the coating optimization from an improved end-use standpoint. As a result of this work two invention disclosures, one for optimizing drying methodology and the other for an in-line system for flaw detection, have been filed. In addition, 2 papers are being written for submission to peer-reviewed journals.

25 ENERGY STORAGE↗

Validation and Verification of the Correct Operation of the Spectro RS23 UV-VIS Spectrometer used in ANC122 and NF-ANC122

In September of 2011, the old qualified Bausch and Laum Spec 100 UV-Vis instrument used in the ANC122 and NF-ANC122 procedures failed its monthly calibration check. Attempts to get the system to pass by cleaning flow cells, replacing the light bulb and realigning the light path failed to get sustained reproducible results from the system. In October the decision to take it out of service was made as the system was 40+ years in age. To replace the system, a previously purchased Labomed Inc.’s spectrometer (model Spectro 23RS; Serial #: 23RS-004253) was retrieved from storage. This report shows that the Labomed Inc. system is performing as required and meeting all QC requirements listed in ANC122 and NF-ANC122. Upon submitting this report to records, the system will be considered qualified to report results to customers of C-AAC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Contribution to the Development of DOE ARM Climate Best Estimate Data (ARMBE) Products: Land Surface Forcing and Evaluation Data Set (ARMBE-LAND) from the ARM SGP Site

To support the LLNL ARM Best Estimate Data Products (ARMBE) data development, the San Jose State University (SJSU)’s group will provide the LLNL team yearly data files (in a format consistent with ARMBE) that contain variables from the instruments defined in Table 1 for the ARM SGP site during the available period. The ARMBE-Land data product will blend multiple ARM observations including the Energy Balance Bowen Ratio Station (EBBR), Soil Water and Temperature System (SWATs) and CO2 Flux (CO2FLX) data sets. The SJSU group will process these datasets with stringent quality controls to remove suspicious data points and average quality-controlled data over a desired temporal resolution (one hour). A qc-flag will be assigned to each variable to indicate how many valid data points are used to get the hourly mean data, consistent with other ARMBE fileds.

54 ENVIRONMENTAL SCIENCES↗

Final Report - Recovery Act - Development and Application of Processing and Process Control for Nano-Composite Materials for Lithium Ion Batteries

Oak Ridge National Laboratory and A123 Systems, Inc. collaborated on this project to develop a better understanding, quality control procedures, and safety testing for A123 System s nanocomposite separator (NCS) technology which is a cell based patented technology and separator. NCS demonstrated excellent performance. x3450 prismatic cells were shown to survive >8000 cycles (1C/2C rate) at room temperature with greater than 80% capacity retention with only NCS present as an alternative to conventional polyolefin. However, for a successful commercialization, the coating conditions required to provide consistent and reliable product had not been optimized and QC techniques for being able to remove defective material before incorporation into a cell had not been developed. The work outlined in this report addresses these latter two points.

Nuclear Criticality Safety Program (NCSP)↗

Satellite-Based Solar Resource Data Sets for India 2002-2012

A new 10-km hourly solar resource product was created for India. This product was created using satellite radiances from the Meteosat series of satellites. The product contains global horizontal irradiances (GHI) and direct normal irradiances (DNI) for the period from 2002 to 2011. An additional solar resource data set covering the period from January 2012 to June 2012 was created solely for validation because this period overlaps ground measurements that were made available from the Indian Ministry of New and Renewable Energy's (MNRE's) National Institute for Solar Energy for five stations that are part of MNRE's solar resource network. These measurements were quality checked using the SERI QC software and used to validate the satellite product. A comparison of the satellite product to the ground measurements for the five stations shows good agreement. This report also presents a comparison of the new version of solar resource data to the previous version, which covered the period from 2002 to 2008.

14 SOLAR ENERGY↗

Informal Preliminary Report on Comparisons of Prototype SPN-1 Radiometer to PARSL Measurements

The prototype SPN-1 has been taking measurements for several months collocated with our PNNL Atmospheric Remote Sensing Laboratory (PARSL) solar tracker mounted instruments at the Pacific Northwest National Laboratory (PNNL) located in Richland, Washington, USA. The PARSL radiometers used in the following comparisons consist of an Eppley Normal Incident Pyrheliometer (NIP) and a shaded Eppley model 8-48 “Black and White” pyrgeometer (B&W) to measure the direct and diffuse shortwave irradiance (SW), respectively. These instruments were calibrated in mid-September by comparison to an absolute cavity radiometer directly traceable to the world standard group in Davos, Switzerland. The NIP calibration was determined by direct comparison, while the B&W was calibrated using the shade/unshade technique. All PARSL data prior to mid-September have been reprocessed using the new calibration factors. The PARSL data are logged as 1-minute averages from 1-second samples. Data used in this report span the time period from June 22 through December 1, 2006. All data have been processed through the QCRad code (Long and Shi, 2006), which itself is a more elaborately developed methodology along the lines of that applied by the Baseline Surface Radiation Network (BSRN) Archive (Long and Dutton, 2004), for quality control. The SPN-1 data are the standard total and diffuse SW values obtained from the analog data port of the instrument. The comparisons use only times when both the PARSL and SPN-1 data passed all QC testing. The data were further processed and analyzed by application of the SW Flux Analysis methodology (Long and Ackerman, 2000; Long and Gaustad, 2004, Long et al., 2006) to detect periods of clear skies, calculate continuous estimates of clear-sky SW irradiance and the effect of clouds on the downwelling SW, and estimate fractional sky cover.

Long, Charles N.↗

Station-based Surface Data Value-Added Product

This report describes the Atmospheric Radiation Measurement (ARM) Best Estimate (ARMBE) station-based surface data (ARMBESTNS) value-added product. It is a twin data product of the ARMBE 2-Dimensional gridded (ARMBE2DGRID) data set. Unlike the ARMBE2DGRID data set, ARMBESTNS data are reported at the original site locations and show the original information (except for the interpolation over time). Therefore, the users have the flexibility to process the data with the approach more suitable for their applications. This document provides information about the input data, quality control (QC) method, and output format of this data set. As much of the information is identical to that of the ARMBE2DGRID data, this document will emphasize more on the different aspects of these two data sets.

97 MATHEMATICS AND COMPUTING↗

Validation and Verification of the Correct Operation of the Thermo Fisher Scientific’s Genesys 10S spectrometer used in ANC122 and NF-ANC122

In December of 2015, the old qualified Prim UV-Vis instrument used in the ANC122 and NFANC122 procedures failed its monthly calibration check. Attempts to get the system to pass by cleaning flow cells, replacing the light bulb and realigning the light path failed to get sustained reproducible results from the system. As it could no longer pass QA/QC requirements the decision to take it out of service was made. To replace the system, a previously purchased Thermo Fisher Scientific UV-VIS spectrometer (model Genesys 10S; Serial #: 2L5R059137) was retrieved from storage. This report shows that the system is performing as required and meeting all QC requirements listed in ANC122 and NF-ANC122

47 OTHER INSTRUMENTATION↗

BWR Steam Dryer Alternating Stress Assessment Procedures

This report presents an overview of Boiling Water Reactor (BWR) steam dryer design; the fatigue cracking failures that occurred at the Quad Cities (QC) plants and their root causes; a history of BWR Extended Power Uprates (EPUs) in the USA; and a discussion of steam dryer modifications/replacements, alternating stress mechanisms on steam dryers, and structural integrity evaluations (static and alternating stress).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

MQXFS1 Quadrupole Fabrication Report

This report presents the fabrication and QC data of MQXFS1, the first short model of the low-beta quadrupoles (MQXF) for the LHC High Luminosity Upgrade. It describes the conductor, the coils, and the structure that make the MQXFS1 magnet. Qualification tests and non-conformities are also presented and discussed. The fabrication of MQXFS1 was started before the finalization of conductor and coil design for MQXF magnets. Two strand design were used (RRP 108/127 and RRP 132/169). Cable and coil cross-sections were “first generation”.

43 PARTICLE ACCELERATORS↗

Confirmatory LBL Analysis of AGR-5/6/7 Compacts and Over-Coated Particles BWXT Batches 11034, 14154C, 14156C, AND 14156D

Fuel for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) was produced by BWX Technologies (BWXT) Nuclear Operations Group in Lynchburg, Virginia. Tristructural isotropic (TRISO) coatings were deposited using a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace on 425-μm-nominal-diameter spherical kernels from Lot J52R-16-69317 containing a mixture of 15.5% 235U low-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μmnominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. TRISO-coated particle Lot J52R-16-98005 was over-coated with a graphite/resin blend and these over-coated particles were pressed in half-inch-diameter, one-inch-long cylindrical compacts. Two packing fractions (PF) were produced, 40%PF and 25%PF, where the TRISO particle volume made up approximately 40% and 25% of the total compact volume, respectively. The AGR-5/6/7 Fuel Specification, SPC-1352 [Marshall 2016], provides the requirements necessary for acceptance of the fuel manufactured for the AGR-5/6/7 irradiation test. Quality control (QC) acceptance testing for all AGR-5/6/7 composited lots and single batches was performed by BWXT, with the exception of pyrolytic carbon (PyC) anisotropy and defective IPyC fraction in the TRISO candidate batches and final composite, which were measured at the Oak Ridge National Laboratory (ORNL) and reported in ORNL/TM-2017/036 [Hunn et al. 2017] and ORNL/TM-2017/037 [Helmreich et al. 2017a].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantum Computing for Quantum Simulation for NNSA Mission

Beginning with Feynman in 1982, it was proposed that highly controllable quantum devices, later to become known as quantum computers, would be especially good at the simulation of other quantum systems. Around the turn of the 21st century, this notion was later formalized (by Lloyd and coworkers at MIT and Laflamme and coworkers at Los Alamos) to show how in particular instances, we expect an exponential speedup in the solution of the Schroedinger equation for chemical systems. Subsequently, quantum-accelerated quantum simulation for chemistry techniques have been developed by IBM, Google, Harvard, etc. This effort has led to the OpenFermion (openfermion.org, OF) community, an open source effort for compiling and analyzing quantum algorithms to simulate fermionic systems, including quantum chemistry. Among other functionalities, the current version of OF features data structures and tools for obtaining and manipulating representations of fermionic and qubit Hamiltonians. In October, 2017, the cover of Chemical and Engineering News posited “Quantum computers: Chemistry could be the machine’s killer app” for first principles understanding of biological systems and complex materials. Prof. Aspuru-Guzik (Harvard) predicts “I think that before 2035 QC will be beating classical computers at chemistry.” The algorithms at the heart of quantum chemistry codes (eigensolvers, fast fourier transforms) are the computation bottleneck.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sampling and Analysis Plan for USDOE/NNSA Pantex Plant Groundwater Remedial Action Progress

This Sampling and Analysis Plan (SAP) was originally developed as part of the Remedial Design Submittal Package required by the Interagency Agreement (IAG) for the United States Department of Energy/National Nuclear Security Administration (USDOE/NNSA) Pantex Plant. The SAP describes specifications for data collection, methods of sample collection and analysis, and requirements for quality assurance (QA) and quality control (QC) activities implemented during the life cycle of the program to ensure that data are of sufficient quality for their intended purpose (i.e., to support decision making regarding remediation of the groundwater beneath Pantex). The SAP was prepared according to United States Environmental Protection Agency (EPA) guidance on preparation of Quality Assurance Project Plans (QAPPs) QA/R-5 (EPA, 2001) and is designed to be a stand-alone document that describes both field sampling activities as well as QA/QC activities. The SAP is incorporated by reference to the compliance plan provisions of Hazardous Waste Permit No. 50284, issued by the Texas Commission on Environmental Quality, and was submitted as part of the Remedial Design/Remedial Action Work Plan submitted to EPA in accordance with the Interagency Agreement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

$\beta-\gamma$ Absolute Calibration (Rev. 1)

Identification of nuclear events rely on accurate measurement of radioxenon releases. Measurement of radioxenon relies on accurately knowing the detection efficiency for each isotope. Four xenon isotopes are of interest: 135 Xe, 133 Xe, 133 mXe, and 131 mXe. Each isotope has a unique signature; however, there is overlap between each signature. A series of ratio terms, called interference ratios, helps account for the challenges created by the overlap. The ratio and detection efficiency terms are all determined during the initial detector calibration. Additional spectra are needed for a complete calibration: the radon daughter 214 Pb/ 214 Bi, the detector background, and the 137 Cs quality control (QC).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quantum Information Science: Factual Document for the Office of Basic Energy Sciences at the Department of Energy

For decades, scientists have known that devices to store and manipulate information in quantum physical systems such as atoms or photons would provide radical new capabilities in computing, communication, and sensing. These novel capabilities include speed-ups in scientific calculations of quantum materials and chemical systems, enhanced resolution in imaging and detection systems, and greater security for encrypted communication systems. Building these devices requires a detailed understanding of how quantum materials behave, accurate knowledge of how to integrate them, and high-fidelity control of the physical qubits that store information. These goals are fundamental research challenges for materials synthesis, fabrication, and characterization; and the science of quantum information intersects heavily with ongoing basic research into materials science, chemistry, and quantum physics. These systems represent state-of-the-art approaches to building and controlling the basic physical elements of quantum information. Research into quantum sensing and quantum communication strongly leverages these advances for next-generation technologies, e.g., measurements beyond the Heisenberg limit, while applications of quantum computing (QC) as a platform for understanding future quantum material systems highlight its potential for advanced scientific discovery. This factual status document for Quantum Information Science has been developed for the Department of Energy Office of Science, Basic Energy Sciences (BES). The following are several seminal or key references for interested readers; the reference section gives a more exhaustive, but still not complete, list of important papers in this area.

36 MATERIALS SCIENCE↗

IDC Re-Engineering Phase 2 Iteration E2. Draft Component Interface Specification: Signal Detection Control

This report contains a draft Component Interface Specification (CIS) for an application controlling signal detection calculations. It is an example of the contents and level of detail of information in a CIS. The classes, interfaces, and data types in this report reflect current understanding of system concepts and potential implementation patterns but should not be interpreted as containing the finalized interface specifications, classes, etc. The primary purpose of this report is to discuss the potential OSD APIs represented in class diagrams for the Waveform, QC Mask, and Signal Detection Repository interfaces.

42 ENGINEERING↗

MCC On Boarding Section J-2 (Exhibit H) Quality Assurance Requirements [Slides]

Upon MATOC Award, SUBCONTRACTOR shall submit a Quality Assurance Program for evaluation in accordance with subcontract technical and quality requirements. This may be the Subcontractors corporate QA program. Acceptance by Triad of the SUBCONTRACTORS Quality Assurance Program (QAP), as prescribed in Exhibit H, QC-01A and 01B, allows the SUBCONTRACTOR to execute this contract using their approved QAP. SUBCONTRACTORS QAP as approved by CONTRACTOR must meet the applicable requirements of DOE Order 414.1D (see next slide) and must address flow down of the quality requirements to lower tier subcontractors. Triad acceptance of SUBCONTRACTOR’s QAP approval is required prior to Notice to Proceed with on-site work. A Project Specific QA plan may on rare occasions be required for a specific task

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗