Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Protection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Potential of thin, sputtered films as erosion resistant protective coatings, part 1

The characteristics of thin, pyrolytically deposited films for protection of surfaces from oxidation and abrasion are discussed. The limitations of depositing erosion resistant films are described. Environmental tests of first stage compressor blades in a T-58 engine after coating with a thin film were conducted. Photographic examples of the effectiveness of the thin films in protecting the turbine blades are provided. Methods for operating a sputtering system and the equipment used for film deposition are defined.

Gentner, K.↗
NASA NTRS1974

Pathogenetic validation of the use of biological protective agents and early treatment in cases of radiation injury simulating radiation effects under space flight conditions

In considering a radiation safety system for space flights, the various measures to protect man against radiation include drug prophylaxis. At the present time a great deal of experimental material has been accumulated on the prevention and treatment of radiation injuries. Antiradiation effectiveness has been established for sulfur- and nitrogen-containing substances, auxins, cyanides, polynucleotides, mucopolysaccharides, lipopolysaccharides, aminosaccharides, synthetic polymers, vitamins, hormones, amino acids and other compounds which can be divided into two basic groups - biological and chemical protective agents.

Rogozkin, V. D.↗
NASA NTRS1972

Protective overcoating of films

Kodak Film Type SO-212 was emulsion overcoated with gelatin and lacquer to evaluate the feasibility of application of the coatings, any image degradation, and the relative protection offered against abrasion. Evaluated were: Eastman motion picture film lacquer Type 485, water solutions of Eastman purified Calfskin gelatin, and experimental Eastman gelatin stripping film of 4 and 6 microns. Conclusions reached were: (1) All coatings can be applied with relative ease with the only limitation being that of equipment. (2) None of the coatings degrade the processed image. (3) All of the coatings provide protection to the emulsion. These conclusions apply to any film which may be considered for overcoating.

Maas, K. A.↗
NASA NTRS1974

Application of ERTS-1 data to the protection and management of New Jersey's coastal environment

The author has identified the following significant results. Quasi-operational information products for coastal zone management have been prepared using ERTS-1 imagery and collateral aerial photography. These products were applied to the practical regulation, protection, and management of New Jersey's coastal environment. Procedures were developed for the operational use of ERTS-1 data products within New Jersey's Department of Environmental Protection. Successful analysis and product preparation for operational needs centered on four major coastal resource problem areas: (1) detection of environmental changes in coastal areas, (2) siting of ocean outfalls, (3) monitoring of offshore waste disposal, and (4) calculation of recession rates along the Atlantic Shore. The utility and monetary benefits derived from ERTS and aircraft imagery for each problem area have been determined. The NJDEP estimates the possibility of $620,000 yearly savings through the use of an operational ERTS system and a one-time savings of $2.8 million on current or planned projects if a truly operational ERTS type satellite were available.

Yunghans, R. S.↗
NASA NTRS1976

The Langley thermal protection system test facility: A description including design operating boundaries

A description of the Langley thermal protection system test facility is presented. This facility was designed to provide realistic environments and times for testing thermal protection systems proposed for use on high speed vehicles such as the space shuttle. Products from the combustion of methane-air-oxygen mixtures, having a maximum total enthalpy of 10.3 MJ/kg, are used as a test medium. Test panels with maximum dimensions of 61 cm x 91.4 cm are mounted in the side wall of the test region. Static pressures in the test region can range from .005 to .1 atm and calculated equilibrium temperatures of test panels range from 700 K to 1700 K. Test times can be as long as 1800 sec. Some experimental data obtained while using combustion products of methane-air mixtures are compared with theory, and calibration of the facility is being continued to verify calculated values of parameters which are within the design operating boundaries.

Klich, G. F.↗
NASA NTRS1975

Space shuttle program: Lightning protection criteria document

The lightning environment for space shuttle design is defined and requirements that the design must satisfy to insure protection of the vehicle system from direct and indirect effects of lightning are imposed. Specifications, criteria, and guidelines included provide a practical and logical approach to protection problems.

Source record↗
NASA NTRS1976

Material development aspects of an oxidation protection system for a reinforced carbon-carbon composite

The paper describes the procedures which led to selection of a diffusion-coated siliconized oxidation-resistant reinforced carbon-carbon composite as a candidate for use in the leading edge structure of the Space Shuttle for the purpose of providing thermal protection. Materials were evaluated on the basis of oxidation-inhibitor performance, strength properties, and fabricability. Compounds of titanium, tantalum, zirconium, silicon, hafnium, aluminum, and boron were compounded with the reinforced carbon-carbon material in two different processing techniques to discover an oxidation-inhibited system which provided multicycle protection at temperatures up to 4000 F. Details of the manufacture and testing of the reinforced carbon-carbon composites are provided.

Rogers, D. C.↗
NASA NTRS1976

Arc discharge supply component protection circuitry

In a mercury-bombardment ion engine, the discharge supply is a high-current low-voltage one that maintains an arc or discharge inside the engine. In a 30-cm engine the supply provides up to 45 volts at about 13 amperes and is referenced at approximately 1100 volts above ground. Due to the engine discharge characteristics, a very slow feedback control loop is required. A high-speed current limit must be used to protect the components in the power conditioner, a pulse-width-modulated bridge inverter. A high-speed cycle-by-cycle current-limit circuit which allows the inverter to continue running in an overcurrent condition is used to protect it. The high-speed current sensing allows the inverter to be turned off each half cycle before the current in the primary of the inverter exceeds a safe level. This permits the inverter to continue to provide current into a discharge or a fault condition, until the feedback control system can actively control the current.

Ahrens, A. F.↗
NASA NTRS1977

Ceramic composite protection for turbine disc bursts

Ceramic composite turbine disc protection panels for the A300B were developed using armor technology. Analytical predictions for modifying the ballistic projectile armor system were verified by a test program conducted to qualify the rotor containment system. With only a slight change in the areal density of the armor system a more than two-fold increase in kinetic energy protection level was achieved. Thickness of the fiberglass reinforced plastic backing material was increased to achieve an optimum ratio of ceramic thickness to backing thickness for the different ballistic defeat condition.

Gardner, P. B.↗
NASA NTRS1977

Fuel system protection

The hazardous nature of most fuels and the potential for catastrophe if ignition should occur was investigated in regard to the design of adequate lightning protection for aircraft fuel systems. Typical aircraft fuel flammability characteristics and possible ways to control fuel flammability and ignition were reviewed. Guidelines for effective protection of fuel systems were delineated.

Franklin A Fisher↗
NASA NTRS1977

Structures Protection

Materials of which an aircraft is made and the methods used to hold these materials together forming the aircraft structure were studied as factors important in protecting a modern aircraft from hazardous natural environments. Since all-metal aircraft are being replaced by aircraft constructed partly of fiber reinforced plastics with desirable light weight and high strength properties but with poor electrical conductivity, the danger of lightning strikes has become more serious. Lightning effects on metal structures were reviewed and design protection was discussed. The expected lightning effects on nonmetallic materials such as fiberglass and advanced composites were also reviewed.

Franklin A Fisher↗
NASA NTRS1970

Electroplating offers embrittlement protection

Thin copper electrodeposited layer protects metal parts in environments with which they may be incompatible. Originally developed for main engine of Space Shuttle where high strength nickle alloy bellows must operate in high-pressure hydrogen, technique protects nickel and is unaffected by forming process or subsequent heat treatment and preinstallation processing.

Daniels, C. M., Jr.↗
NASA NTRS1979

Tests of a protective shell passive release mechanism for hypersonic wind-tunnel models

A protective shell mechanism for wind tunnel models was developed and tested. The mechanism is passive in operation, reliable, and imposes no new structural design changes for wind tunnel models. Methods of predicting the release time and the measured loads associated with the release of the shell are given. The mechanism was tested in a series of wind tunnel tests to validate the removal process and measure the pressure loads on the model. The protective shell can be used for wind tunnel models that require a step input of heating and loading such as a thin skin heat transfer model. The mechanism may have other potential applications.

Puster, R. L.↗
NASA NTRS1979

Flight test evaluation of an RAF high altitude partial pressure protective assembly

A partial pressure suit was evaluated during tests in an F-104 and F-15 as a protective garment for emergency descents. The garment is an pressure jerkin and modified anti-g suit combined with an oronasal mask. The garment can be donned and doffed at the aircraft to minimize thermal buildup. The oronasal mask was favored by the pilots due to its immobility on the face during high g-loading. The garment was chosen to provide optimum dexterity for the pilot, which is not available in a full pressure suit, while protecting the pilot at altitudes up to 18,288 meters, during a cabin decompression, and subsequent aircraft descent. During cabin decompressions in the F-104 and F-15, cabin pressure altitude was measured at various aircraft angles of attack, Mach numbers, and altitudes to determine the effect of the aerodynamic slipstream on the cabin altitude.

Ashworth, G. R.↗
NASA NTRS1979

Feasibility study of silicon nitride protection of plastic encapsulated semiconductors

The application of low temperature silicon nitride protective layers on wire bonded integrated circuits mounted on lead frame assemblies is reported. An evaluation of the mechanical and electrical compatibility of both plasma nitride and photochemical silicon nitride (photonitride) passivations (parallel evaluations) of integrated circuits which were then encapsulated in plastic is described. Photonitride passivation is compatible with all wire bonded lead frame assemblies, with or without initial chip passivation. Plasma nitride passivation of lead frame assemblies is possible only if the chip is passivated before lead frame assembly. The survival rate after the environmental test sequence of devices with a coating of plasma nitride on the chip and a coating of either plasma nitride or photonitride over the assembled device is significantly greater than that of devices assembled with no nitride protective coating over either chip or lead frame.

Peters, J. W.↗
NASA NTRS1978

Space Shuttle Orbiter thermal protection material development and testing

The research work described in the present paper was carried out to develop and evaluate thermal protection materials for application to the Space Shuttle and future programs. The philosophy, methodology of testing, and facilities are discussed which had to be developed in view of the new requirements placed on the thermal protection system, in particular the requirement of multiple flight capability.

Larson, H. K.↗