Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Role of the separatrix density in the pedestal performance in deuterium low triangularity JET-ILW plasmas and comparison with JET-C

A reduction of the pedestal pressure with increasing separatrix density over pedestal density (nesep/neped) has been observed in JET. The physics behind this correlation is investigated. The correlation is due to two distinct mechanisms. The increase of nesep/neped till ≈0.4 shifts the pedestal pressure radially outwards, decreasing the peeling-balloning stability and reducing the pressure height. The effect of the position saturates above nesep/neped ≈ 0.4. For higher values, the reduction of the pedestal pressure is ascribed to increased turbulent transport and, likely, to resistive MHD effects. The increase of nesep/neped above ≈0.4 reduces ∇ne/ne, increasing ηe and the pedestal turbulent transport. This reduces the pressure gradient and the pedestal temperature, producing an increase in the pedestal resistivity. The work suggests that the increase in resistivity might destabilize resistive ballooning modes, further reducing the pedestal stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Effects of thermophoresis on high-pressure binary-species boundary layers with uniform and non-uniform compositions

Direct numerical simulations of high-pressure binary-species temporal boundary layers are performed to investigate the flow physics for three situations: (1) uniform and equal composition, (2) uniform but unequal compositions and (3) non-uniform composition. Both colder- and hotter-wall situations compared with the free stream are simulated. The working fluid is a nitrogen/methane mixture. The analysis is performed at a case-specific self-similar state. Even when the initial composition is uniform, the methane mean mass fraction decreases near the colder wall, whereas it increases near the hotter wall and the mass fraction fluctuates in the entire boundary layer. Analysis of the species-mass diffusion balance and flow structures reveal that both mass-fraction variation and fluctuations are induced by the Soret effect. When the initial composition is non-uniform and the wall is colder, the methane mean mass fraction monotonically increases from the wall akin to its initial profile. However, when the wall is hotter the mean mass fraction decreases near the wall in contrast to its initial profile, a fact traced through the species-mass diffusion balance to the Soret effect being large and enriching methane near the wall. In contrast, the direction of the Soret flux is opposite for the colder wall, thus keeping the methane concentration small. Although the initial magnitude of the difference between the wall and free-stream temperature is the same in all cases, the situation is not symmetric between colder- and hotter-wall cases; the flow structure exhibits much smaller scales when the wall is hotter than when the wall is colder.

Mechanics↗
DOE OSTI2020

A multi-dimensional dataset for two-phase instability in low pressure natural circulation based on direct transient local measurement

Thermal hydraulic instability can challenge the control and the safety of nuclear reactors. This experimental research captures and investigates the instability in a low-pressure (1–10 atmospheres) natural circulation loop with an adiabatic chimney installed above the heated section. Direct transient local measurement of two-phase flow is performed at multiple axial locations along the flow channel with thermocouples and conductivity probes traversed by customized high-precision mechanisms. Based on the periodicity of oscillations, a post-processing method is proposed to align the data captured non-simultaneously to reconstruct the instability behavior in one representative period. The averaging operation over multiple oscillation cycles is performed to reduce the random errors. Cyclic phenomena are clearly demonstrated by the post-processed data, and rapid void fraction change induced by the flashing is observed to be significant in the driving mechanism for low pressure oscillations. Parametric effects of inlet subcooling, heat flux, inlet flow restriction and system pressure are studied within the experiment range, and qualitative results are explained and compared with existing literature. The ratio between the oscillation period and the travelling time of the fluid particle through the test section is compared with the theoretical value for the density wave oscillation. The new dataset contains directly measured transient multi-dimensional two-phase data along the flow channel for natural circulation under density wave oscillations. The generated dataset is valuable for the validation of system analysis codes and CFD codes in the simulation of natural circulation phenomena and dynamic two-phase flow.

42 ENGINEERING↗
DOE OSTI2020

Scaling of Imbibition Front Dynamics in Heterogeneous Porous Media

Here we report a quantitative study on the dynamics of countercurrent imbibition in fractured rock samples with the application of CO 2 geosequestration, as the rock matrix is saturated with CO 2 and brine exists in the adjacent microfracture. Direct pore-scale simulations of spontaneous and forced imbibition in a three-dimensional heterogeneous porous matrix enable us to capture the effect of microscopic properties on the imbibition dynamics as these pore-level descriptions are ignored in the existing coarse-grained models. We have established new scaling classes for the propagation of the center of mass of the imbibition front and fluid-fluid interface broadening. It has become evident that the wettability is a major factor which leads to anomalies in these scaling laws. While the governing capillarity under the water-wet condition induces fast roughening dynamics of the interface, the adverse effect of capillary pressure under the intermediate-wet condition leads to a damping effect on the imbibition front fluctuations.

58 GEOSCIENCES↗
DOE OSTI2021

Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments

The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Laminar burning speed measurements for hydrogen enhanced natural gas in a spherical chamber

This work presents laminar burning speed measurements for natural gas and hydrogen enhanced natural gas in gas-turbine conditions using a spherical combustion chamber at an initial temperature and pressure of 296 K and 10 atm, respectively. Natural gas and hydrogen fuels were prepared and mixed with a synthetic air mixture comprised of oxygen, nitrogen, and helium. The experimental data collected during 10 atm ignition was used to predict the LBS at elevated pressures (30 bar) to approach gas-turbine operating conditions. A significant enhancing effect of combustion pressure on LBS was observed, as well as H2 dilution. This work provides fundamental combustion data relevant to sustainable fuels to reduce economic dependence on carbon-based fossil fuels and reduce anthropogenic climate effects through 2050.

Yovino, Louis↗
DOE OSTI2023

New coal char-based bricks: Effects of curing temperature, humidity, pressing pressure, and addition of superplasticizer on the physical, mechanical, and thermal properties

Coal char, as a sustainable and eco-friendly material, holds significant potential for use in new construction materials, specifically, coal char-based bricks. This study employed the pre-pressing method to create char bricks containing high char content of 70%. The impact of various curing temperatures (20, 40, 60 °C), humidity levels (15% and 90%), and pressing pressures (3.5, 7, and 10 MPa) on the density, X-ray diffraction, compressive strength, and thermal conductivity of char-based samples were examined. The addition of superplasticizer and the performance of char bricks were assessed by comparing them to traditional clay bricks and corresponding standards. The study discovers that the temperature of 40 °C enhances the early 7-day strength of char brick samples, while the highest 28-day strength is observed in char bricks at a temperature of 20 °C and humidity of 90%. Compared to conventional clay bricks (with density of 1.9 g/cm3, thermal conductivity of 0.39-0.63 W/mK, compressive strength of 10-20 MPa), the proposed char bricks exhibit lower density (~0.8 g/cm 3 ), lower thermal conductivity (0.26-0.35 W/mK), and good performance in compressive strength (up to 15 MPa). Lastly, coal char-based bricks with high char content demonstrate significant advantages over traditional clay bricks, making them a sustainable and environmentally friendly building material option.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of insulator length and fill pressure on filamentation and neutron production in a 4.6 kJ dense plasma focus

Optimization of neutron yields from dense plasma focus devices is a complex multi-faceted challenge that necessitates the prudent selection of mechanical constraints such as the electrode and insulator geometries. Here, the neutron yield is found to significantly depend on the insulator length. As the length of the insulator increases, the exposed anode length traveled by the sheath during the run-down phase decreases. This suggests an increase in the optimal fill pressure with increasing insulator length to maintain the pinch time near peak current. However, in the present study, the opposite trend is observed—the optimal fill pressure for neutron production decreases with increasing insulator length. Optical probing of the sheath from run-down to the pinch reveals significant plasma filamentation with increasing pressure and a dependence of insulator length on filamentation onset. A direct consequence of increased filamentation is a reduction in mass sweeping efficiency, directly quantified as a function of fill pressure for the first time.

Hahn, E. N. (ORCID:0000000223050532)↗
DOE OSTI2022

Benchmarking Solid-State Batteries Containing Sulfide Separators: Effects of Electrode Composition and Stack Pressure

Integrating sulfide separators into solid-state batteries (SSBs) containing high energy cathodes typically requires one or more materials and engineering solutions including: (i) applying interfacial coatings to mitigate electrolyte decomposition, (ii) applying high stack pressures to form robust solid-solid contacts, and (iii) using alloying anodes to avoid Li dendrite formation. Despite the promise of these approaches, a lack of standardized testing protocols makes it difficult to directly compare results among different studies. To address this problem, the present work benchmarks the performance of SSBs containing β-Li 3 PS 4 (LPS) separators and composite cathodes. By systematically varying the anode/cathode composition and stack pressure, this work demonstrates that cathode design is a major bottleneck for solid-state cells cycled at low rates (<100 µA cm -2 ). Operando stack pressure measurements show that, while mechanical confinement generally promotes higher active material utilization and cycling stability, this strategy alone does not address interfacial reactivity between LPS and high voltage cathodes. Here, these results also demonstrate that stress evolution during cycling is dominated by volume changes at the Li metal anode. Finally, we show that FeS 2 cathodes with moderate operating voltages (<3 V vs Li/Li + ) exhibit superior cycling performance compared to high voltage cathodes by facilitating formation of stable cathode/electrolyte interfaces.

25 ENERGY STORAGE↗
DOE OSTI2022

Foam Fracturing Study for Stimulation Development of Enhanced Geothermal Systems

This is a final technical report for the project: Foam Fracturing Study for Stimulation Development of Enhanced Geothermal Systems (EGS). The goal is to demonstrate the feasibility of foam fracturing in EGS applications. The project, led by Oak Ridge National Laboratory (ORNL), was conducted in collaboration with Temple University. The report describes the research activities with Task 1 at ORNL: foam fracturing testing system development and experimental study on foam fracturing, and Task 2 at Temple University: foam testing and foam characterization. Main findings are: 1. A foam fracturing test system has been developed at ORNL, which can be used to perform foam fracturing under pressure up to 6,000 psi. The system monitors foam density during fracturing online and is capable of testing materials in both monotonic and cyclic (up to 50 Hz) injections. 2. Foam fracturing tests were carried out on Charcoal black granite specimens with a blind borehole to the middle length. Two diameters of blind borehole were tested; G2 series: 9.53 mm and G3 series: 4.76 mm. N2-in-water foam was used with AOS as a surfactant. 3. There was a hole-size effect on fracture initiation pressure. The effect is smaller in the case of foam, which was influenced by the high penetrability of gas in foam. Breakdown pressure showed a behavior just as that of fracture pressure; namely an increased value for small hole samples, while the effect in water fracture was more impressive than in foam fracture. 4. Water mass was reduced in foam fracturing within similar range of breakdown pressures. In G2 series, it was decreased from 10.44 g for water fracturing to 5.17 g, representing more than 50% water reduction. Therefore, there is the potential to reduce water use in EGS stimulation through foam fracturing. 5. Use of cyclic injection has the potential to reduce the breakdown pressure and seismicity in EGS application. Experiments using 4-s cycle period found that specimens can be fractured with a low number of cycles. The fatigue pressure was approximately 64 - 77% of monotonic breakdown pressure for water fracturing and 58 - 94% of the breakdown pressure for foam fracturing. 6. A foam stability testing system has been developed that can test foam at 220 Deg C to 2,000 psi. Tested components of candidate foams included two gases: N2 and CO2; 4 surfactants: AOS, SDS, NP-40 and CTAC; 5 stabilizing agents: guar, bentonite clay, borate salt, silica NPs, and GO. 7. N2 and AOS provided the most stable performance over the tested ranges. Furthermore, the AOS foam with stabilizing agents of guar and borate salt (crosslinker) offered the highest half-life of 20 minutes at 200 Deg C and 1,000 psi. 8. Arrhenius equation and modified power law have been demonstrated to fit well the half-time vs. temperature and pressure data, respectively. These relations can be useful to provide the suggestion for future foam stability study. This submission contains the supporting data developed during the project: 1) A final technical report 2) Granite fracturing data in monotonic and cyclic injections with water and N2 foam Foam performance data in various temperatures and pressures, including half-time, is submitted separately.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Experimental analysis of conductive drying of paper and board

The primary heat transfer source in the conventional multi-cylinder drying of paper and board is conduction. Conduction is facilitated by high-tension contact with steam-heated cylinders, while convective drying, the main mass transfer source, operates as heated air flows over the paper web in the pockets. This conduction process occurs at elevated temperatures and contact pressures to ensure effective contact between the wet paper web and the heated cylinders. The contact pressures and temperatures of the hot surface significantly influence the conductive drying characteristics. This research paper presents an experimental study that involves designing a simple lab-scale setup with in-situ and continuous sensing capabilities for various commercially available grades of paper and board. Embedded thermocouples measure the temperatures of the heated platen and the sheet, allowing the collection of flux data to determine heat transfer characteristics. Here, the goal of this study is to ascertain the instantaneous contact coefficients for different basis weights as a function of moisture content. The acquired data will provide valuable insights and information towards process development, design and simulation of the paper drying process.

42 ENGINEERING↗
DOE OSTI2021

Mechanical Response of Castlegate Sandstone under Hydrostatic Cyclic Loading

The stress history of rocks in the subsurface affects their mechanical and petrophysical properties. Rocks can often experience repeated cycles of loading and unloading due to fluid pressure fluctuations, which will lead to different mechanical behavior from static conditions. This is of importance for several geophysical and industrial applications, for example, wastewater injection and reservoir storage wells, which generate repeated stress perturbations. Laboratory experiments were conducted with Castlegate sandstone to observe the effects of different cyclic pressure loading conditions on a common reservoir analogue. Each sample was hydrostatically loaded in a triaxial cell to a low effective confining pressure, and either pore pressure or confining pressure was cycled at different rates over the course of a few weeks. Fluid permeability was measured during initial loading and periodically between stress cycles. Samples that undergo cyclic loading experience significantly more inelastic (nonrecoverable) strain compared to samples tested without cyclic hydrostatic loading. Permeability decreases rapidly for all tests during the first few days of testing, but the decrease and variability of permeability after this depend upon the loading conditions of each test. Cycling conditions do affect the mechanical behavior; the elastic moduli decrease with the increasing loading rate and stress cycling. The degree of volumetric strain induced by stress cycles is the major control on permeability change in the sandstones, with less compaction leading to more variation from measurement to measurement. The data indicate that cyclic loading degrades permeability and porosity more than static conditions over a similar period, but the petrophysical properties are dictated more by the hydrostatic loading rate rather than the total length of time stress cycling is imposed.

58 GEOSCIENCES↗
DOE OSTI2023

Multi-Objective Optimization of a Bi-Metal High-Temperature Recuperator for Application in Concentrating Solar Power

Supercritical CO 2 closed Brayton cycles are a major candidate for future power cycle designs in concentrating solar power applications, with high-temperature recuperators playing an essential role in realizing their high thermal efficiency. Here, printed circuit heat exchangers (PCHEs) are often chosen for this role due to their thermal-hydraulic and mechanical performance at high temperatures and pressures, all while remaining compact. However, PCHEs can be costly because of the high-performance materials demanded in these applications, and the heat exchanger internal geometry is restricted by their manufacturing process. Additively manufactured heat exchangers can address both of these shortcomings. This work proposes a modular bi-metal high-temperature recuperator with integrated headers to be produced with additive manufacturing. Beginning with existing PCHE channel geometries, a 1D heat exchanger model is developed. Then, multi-objective optimization is used to maximize the heat transfer effectiveness of a lab-scale device while limiting its size. Two distinct channel geometries emerge from the optimization. Optimal designs achieve up to 88% effectiveness with negligible pressure drop. Deterioration of effectiveness due to axial conduction of heat in the heat exchanger walls is found to be a notable problem for lab-scale PCHEs, and the optimal designs obtained here minimize its detrimental effects. A sensitivity analysis reveals that the effectiveness of the recuperator is much less sensitive to variation in mass flowrate in off-design operation when axial conduction is significant, while increasing the length of the device easily increases effectiveness.

14 SOLAR ENERGY↗
DOE OSTI2025

Fuel reid vapor pressure level and ethanol content on stochastic preignition, effects at steady and unsteady engine operation

The present work investigates relations between fuel Reid vapor pressure (RVP) and biofuel (ethanol) content on stochastic preignition (SPI) at both sustained steady-state engine operation and following load transients. This work stems from in-field observations that automotive original equipment manufacturers have observed consistent seasonal increases in United States customer drivability complaints and warranty claims during September and October where SPI is suspected to be responsible. The seasonal timing of these events coincides with the United States seasonal fuel property changeover initiating on September 15 each year, where fuel RVP increases. To explore potential linkage between fuel RVP and SPI the present study employs engine SPI experiments coupled with laboratory spray measurements of fuels with RVPs of 8, 12, and 16 psi in both E10 (10% ethanol) and E25 (25% ethanol) fuels. Engine results are partitioned into fuel RVP and ethanol content effects on SPI in steady-state, sustained high-load engine operation and unsteady-state low- to high-load transitions, where off-engine spray vessel patternation and tip penetration results help to elucidate the observed fuel effects on SPI. A boosted direct-injected, spark-ignition engine was fueled with three market relevant E10 and E25 fuels with RVPs of 8, 12, and 16 to characterize the interplay between winter fuels and abnormal combustion behavior. The steady-state work shows that for high-load, steady-state engine operation, SPI is directly linked to fuel retention, which was found to be dependent on fuel distillation. The unsteady-state engine operation work shows that following low-to high-load transitions, SPI can occur from a memory of fuel property effects at low-load operation. Specifically, the fuel RVP effect on fuel spray collapse at low loads was found to correlate with SPI with a more than 95% confidence interval following low- to high-engine-load transitions. Results suggest that fuel-wall impingement at low-load operation could carry over into high-load transitions and generate SPI events following low- to high-load transitions.

09 BIOMASS FUELS↗
DOE OSTI2025

Dehydration of Methyl Lactate on Alkali Cation-Exchanged Faujasite: Effects of Metal Cation Identity and Water Pressure

Turnover rates for the catalytic dehydration of methyl lactate (ML) over ion-exchanged faujasite (FAU) catalysts depend on the identity of alkali metal cations (Na + , K + , Cs + ) and local solvation effects. Analysis of rate measurements and in situ infrared spectroscopy gives evidence that the reaction involves kinetically relevant dissociation of adsorbed methyl lactate upon alkali metal cations. This process involves concerted methyl transfer to the surface and dissociation of the alkali metal from the framework, which occurs at cationic active sites that remain predominantly unoccupied under relevant conditions (0.5–10 kPa ML, 0.5–15 kPa H 2 O, 563–583 K). Despite the mechanistic similarities, apparent activation enthalpies (ΔH app ‡ ) decrease linearly (47 kJ mol –1 from Na + to Cs + ) with ionization energy and cationic radius, and apparent activation entropies (ΔS app ‡ ) decrease 74 J mol –1 K –1 . These trends reflect electrostatic interactions that stabilize the cations to the anionic sites on the zeolite: stronger association between these charges leads to increasingly endothermic processes to displace the alkali metal to form a cationic methoxy and an intrapore metal lactate intermediate. Water physisorption measurements suggest alkali metal ions bind superstoichiometric quantities of water within FAU pores, and in situ infrared spectra suggest the concerted adsorption of ML requires reorganization of this water. Consequently, these processes introduce entropic gains that partially offset entropy losses associated with ML adsorption. Hence, turnover rates differ only by a factor of 2 among Na-, K-, and Cs-FAU at 573 K (ΔΔG app ‡ = 5 kJ mol –1 ). These findings demonstrate the interplay of alkali metal ions with zeolite active sites and intrapore water clusters for ML dehydration, indicating that these interactions can be leveraged to deliver optimal performance under different reaction conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part I: Accelerated Ash Loading and DPF Performance Evaluation

The project objective was to generate experimental data to evaluate the impact of metals doped B20 on DPF ash loading and performance compared to that of conventional petrodiesel. Accelerated ash loading was conducted on two DPFs - one exposed to regular diesel fuel and the other to B20 containing metal dopants equivalent to 4 ppm B100 total metals (currently total metals are limited to 10 ppm in ASTM D6751, the standard for B100). Periodic performance evaluations were conducted on the DPFs at 10 g/L ash loading intervals. After the evaluations at 30 g/L, the DPF was cleaned with a commercial DPF cleaning machine and another round of DPF evaluations were conducted. A comparison of the effect of ash loading with the two fuels and DPF cleaning is presented. The metals doped B20 fuel resulted in ash that was similar to that deposited when exposed to ULSD (lube oil ash) and exhibited similar ash cleaning removal efficiency. Metals doped B20 resulted in faster ash accumulation within the DPF, as expected, but did not appear to have a negative effect on DPF pressure drop or regeneration rates (up to 30 g/L of ash) or exhibit deleterious physical effects on the DPF substrate.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2021

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics--based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.

Kulkarni, Shank S.↗
DOE OSTI2022

Planar, longitudinal, compressive waves in solids: Thermodynamics and uniaxial strain restrictions

A new tri-axial pressure-based constitutive expression has been found using Cauchy's stress tensor. This stress state emphasizes pressure and shear stress. The description is a pressure plus an effective shear stress allowing for a constitutive law based on atomic solid-state phase changes in crystalline cells due to pressure plus shear-based dislocation motion commonly associated with plasticity. Pressure has a new role in the material's constitutive response as it is separated from plasticity. The thermo-mechanical system describes third-order Gibbs’ expressions without specific volume restrictions placed upon the material. Isothermally, the ratio of heat to shear work in elastic copper is shown to approach zero at a very low temperature and become larger than one as temperature approaches melting. Wave compression models investigated are elastic and plastic: in fully elastic materials, the planar wave is restricted by Poisson's effect although plastic shear changes this constraint. Plastic deformation, dominated by dissipative shear stresses in uniaxial strain, heats the material while excluding phase changes from hydrostatic pressures. The material properties per se across Hugoniot shocks are described with entropy concepts. Shock waves are exceedingly complex since the constitutive laws are linked at extreme temperatures, pressures, and shear stresses. Isothermal, isentropic, isochoric, and iso-shear conditions are used throughout with Jacobian algebra.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗