Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Operating experience data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Operational experiences of a commercial helicopter flown in a large metropolitan area

A survey of commercial helicopter-operating experiences was conducted using a helicopter flight recorder in order to provide a basis for extending helicopter design and service-life criteria. These data are representative of 182 flight hours accumulated during 1414 flights comprised of the separate legs of the total route structure employed. The operating experiences are presented in terms of the time spent within different airspeed brackets, within the classifiable flight conditions of climb, en route, and descent, at various rates of climb and descent, and at different rotor rotational speeds. The results indicated that the helicopter spent a majority of the flight time at airspeeds either below 40 knots or above 100 knots. Rates of climb and descent were concentrated at values below 5.1 m/s (1000 ft/min) particularly for higher airspeeds. Normal acceleration experiences were low, both in the total number and peak value realized; however, an extremely large number of pitch angular-velocity experiences were noted. Rotor rotational speeds were normal with no occurrences above the upper red-line limit.

Dicarlo, D. J.↗
NASA NTRS1981

An analysis of aircrew procedural compliance

This research examines the relationships between aircrew compliance with procedures and operator errors. The data for this analysis were generated by reexamination of a 1976 experiment in full mission simulation conducted by Dr. H. P. Ruffell Smith (1979) for the NASA-Ames Research Center. The character of individual operators, the chemistry of crew composition, and complex aspects of the operational environment affected procedural compliance by crew members. Associations between enumerated operator errors and several objective indicators of crew coordination were investigated. The correspondence among high operator error counts and infrequent compliance with specific crew coordination requirements was most notable when copilots were accountable for control of flight parameters.

Schofield, J. E.↗
NASA NTRS2019

TCL3 UTM (UAS Traffic Management) Flight Tests, Airspace Operations Laboratory (AOL) Report

The Technology Capability Level-3 (TCL3) flight tests were conducted at six different test sites located across the USA from March to May of 2018. The campaign resulted in over 830 data collection flights using 28 different aircraft and involving 20 flight crews. Flights not only varied in duration, but also in the environments and terrains over which they flew. The TCL3 tests highlighted four different types of tests: three tests focused on Communication, Navigation and Surveillance (CNS); six tests focused on Sense and Avoid (SAA) technologies; six tests focused on USS Data and Information Exchange (DAT); and five tests focused on exploring fundamental Concepts of the project (CON). This document presents data collected during the TCL3 tests that informed the operator’s experiences—the quality of the unmanned aerial system (UAS) Service Supplier (USS) information that the operator was provided with, the usefulness of this information, and the usability of the automation, both while airborne and on the ground. It is intended to complement the reports written by the test sites and the quantitative reports and presentations of the UAS Traffic Management (UTM) project. With the goal of instructing what the minimum information requirements and/or best practices might be in TCL3 operations, the driving enquiry was: How do you get the information you need, when you need it, to successfully fly a UAS in UTM airspace? This enquiry touches on two requirements for displays, which are to provide adequate situation awareness (SA) and to share information through a USS. The six test sites participating in the TCL3 tests flew a subset of the 20 tests (outlined above), with most sites working on a subset of each of the four types: Communications, Navigation and Surveillance (CNS); DAT; CON; and Sense and Avoid (SAA). The, mainly qualitative, data addressed in this report was collected by the AOL (Airspace Operations Laboratory) both on-site and remotely for each test. The data consists of the contents of end-of-day debriefs, end-of-day surveys, observer notes, and flight test information, all submitted as part of the Data Management Plan (DMP).

Martin, Lynne↗
NASA NTRS1990

Comparison of Surface Radiation Budget Satellite algorithms for downwelled shortwave irradiance with Wisconsin Fire/SRB surface-truth data

Surface radiation instruments were operated at various locations during the Wisconsin First ISSCP (International Satellite Cloud Climatology Project) Regional Experiment (FIRE) and Surface Radiation Budget (SRB) experiment in October 1986. Satellite data were distributed to scientists who had previously developed satellite algorithms to estimate downwelled shortwave irradiance. Results of intercomparison of ground-truth values with the satellite-derived estimates are described.

Whitlock, C. H.↗
DOE OSTI2026

Detector Characterization for SuperCDMS Commissioning

Super Cryogenic Dark Matter Search (SuperCDMS) SNOLAB is a next generation direct detection experiment search ing for low mass dark matter using cryogenic germanium and silicon detectors operated at millikelvin temperatures. As the experiment begins its first commissioning data taking, establishing that the detectors respond to energy deposits in a stable, predictable way is a prerequisite for any future physics analysis. This work presents a study of detector stability for four SuperCDMS SNOLAB detectors, det 7 and det 15 (germanium), and det 11 and det 14 (silicon), using two data sets taken during early commissioning: dedicated Barium-133 calibration runs, which provide a known gamma ray energy reference at 356 keV, and low background runs, which record whatever background radiation the detectors see with no external source present. The Ba-133 data do not show a distinct, well localized line at the expected energy, and the low background data show a baseline that drifts and oscillates over time rather than remaining flat. This baseline instability appears consistently across multiple channels rather than being confined to one, suggesting a shared, detector wide cause rather than a single faulty channel. Together, these observations point to the detectors’ cryogenic support system as the likely source of the instability, since small temperature fluctuations introduced during normal operation of the cooling system could plausibly couple into the exquisitely temperature sensitive detectors. These results inform the ongoing commissioning effort by narrowing down where instability in the current data is originating from.

O'Hanlon, Viktoria M. [Skidmore Coll.; Fermilab]↗
DOE OSTI2026

Detector Characterization for SuperCDMS Commissioning

Super Cryogenic Dark Matter Search (SuperCDMS) SNOLAB is a next generation direct detection experiment search ing for low mass dark matter using cryogenic germanium and silicon detectors operated at millikelvin temperatures. As the experiment begins its first commissioning data taking, establishing that the detectors respond to energy deposits in a stable, predictable way is a prerequisite for any future physics analysis. This work presents a study of detector stability for four SuperCDMS SNOLAB detectors, det 7 and det 15 (germanium), and det 11 and det 14 (silicon), using two data sets taken during early commissioning: dedicated Barium-133 calibration runs, which provide a known gamma ray energy reference at 356 keV, and low background runs, which record whatever background radiation the detectors see with no external source present. The Ba-133 data do not show a distinct, well localized line at the expected energy, and the low background data show a baseline that drifts and oscillates over time rather than remaining flat. This baseline instability appears consistently across multiple channels rather than being confined to one, suggesting a shared, detector wide cause rather than a single faulty channel. Together, these observations point to the detectors’ cryogenic support system as the likely source of the instability, since small temperature fluctuations introduced during normal operation of the cooling system could plausibly couple into the exquisitely temperature sensitive detectors. These results inform the ongoing commissioning effort by narrowing down where instability in the current data is originating from.

O'Hanlon, Viktoria M. [Skidmore Coll.; Fermilab]↗
NASA NTRS2009

Data Assimilation Experiments Using Quality Controlled AIRS Version 5 Temperature Soundings

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing and reprocessing of all AIRS data. The AIRS Science Team Version 5 retrieval algorithm contains a number of significant improvements over Version 4. Two very significant improvements are described briefly below. 1) The AIRS Science Team Radiative Transfer Algorithm (RTA) has now been upgraded to accurately account for effects of non-local thermodynamic equilibrium on the AIRS observations. This allows for use of AIRS observations in the entire 4.3 micron CO2 absorption band in the retrieval algorithm during both day and night. Following theoretical considerations, the,AIRS Version 5 temperature profile retrieval step uses only 15 micron CO2 radiances for those channels sensitive to atmospheric emission in the stratosphere. Tropospheric temperature profile information is obtained almost exclusively from clear column radiances in the 4.3 micron CO2 band. These clear column radiances are a derived product that are indicative of radiances AIRS channels would have seen if the field of view were completely clear. Tropospheric sounding 15 micron CO2 observations are used heavily in the determination of the parameters necessary to generate for all sounding channels. This approach allows for the generation of accurate values of and T(p) under most cloud conditions.

Susskind, Joel↗
NASA NTRS1990

Mission and sampling analyses for atmospheric satellite experiments

Orbital analyses, instrument-viewing geometry studies, and sampling simulations are performed to define mission concepts for advanced atmospheric research satellite experiments. These analyses are conducted in collaboration with NASA Headquarters and working groups consisting of atmospheric scientists and experiment developers. Analytical techniques are developed and used to optimize geographical coverage, sensor-viewing geometries, data gathering strategies, sampling schemes, orbital characteristics, satellite launch times, and operational modes of the various experiments and mission concepts. Short-term (7 day) Shuttle Missions, the Upper Atmosphere Research Satellite (UARS), and multisatellite missions such as the Earth Observing System (EOS) are being studied. Atmospheric experiments which are being analyzed include nadir-viewing sounders, limb-emission scanners, laser systems, and solar-occultation techniques.

Harrison, Edwin F.↗
DOE OSTI2020

Simulation and Development of the Radial Time Projection Chamber For the Bonus12 Experiment in CLAS12

Knowledge of the structure of nucleons (i.e. protons and neutrons) is a central topic of interest to nuclear/particle physicists. Much more is known about the structure of the proton than the neutron due to the lack of high-density free neutron targets. The Barely Off-shell Nucleon Structure experiment (BONuS12) at Jefferson Lab (JLab) is a second generation experiment upgraded/optimized to advance our knowledge of the neutron's structure using the deep-inelastic scattering of electrons off deuterium. Typically, since deuterium is a nuclear target, corrections for off-shell and nuclear binding effects must be taken into account in order to extract results on the neutron. These corrections are model-dependent and therefore have limited our success in extracting neutron information using deuterium targets. In the BONuS12 experiment, 10.6 GeV electrons are scattered off of a deuterium target. By detecting the low momentum spectator proton at backward angles, the uncertainty due to final state interactions is minimized. The goal of the experiment is to measure the ratio of the neutron to proton structure functions ($F^n_2/F^p_2$) as the Bjroken scaling variable x approaches 1. The newly designed Radial Time Projection Chamber (RTPC) for BONuS12 detects the spectator proton in coincidence with the scattered electron, which is detected in the CEBAF Large Acceptance Spectrometer (CLAS12). This work presents the simulation and development of the new BONuS12 RTPC. The design, construction, and testing of the Drift-gas Monitoring Sysytem (DMS) for the BONuS12 experiment is also described. The results of the DMS operation as well as the first preliminary data from the BONuS12 experimental run are given. Because the BONuS12 data analysis depends on CLAS12 working effectively, an effort to verify the CLAS12 operation with the extraction of the inclusive deep inelastic cross section from the first experiment in CLAS12 (Run Group A) will be presented.

Dzbenski, Nathan↗
DOE OSTI2020

The CLAS12 Silicon Vertex Tracker

Silicon Vertex Tracker (SVT) has been designed for the CLAS12 spectrometer using single-sided microstrip sensors fabricated by Hamamatsu Photonics. The sensors have a graded angle design to minimize dead areas and a readout pitch of 156 um, with intermediate strips. Each double-sided SVT module hosts three daisy-chained sensors on each side with a full strip length of 33 cm. There are 512 channels per module, read out by four Fermilab Silicon Strip Readout (FSSR2) chips, featuring data-driven architecture, mounted on a rigid–flex hybrid board. The modules are assembled in a barrel configuration using a unique cantilevered geometry to minimize the amount of material in the tracking volume. This paper is focused on the design, qualification of the performance, and experience in operating and commissioning the tracker during the first year of the data taking.

47 OTHER INSTRUMENTATION↗
NASA NTRS1992

Distribution of space-gathered data

A Data Distribution Satellite (DDS) concept for directly distributing space-gathered data to users on the ground and allowing users access to their experiments for real-time control is described. The DDS would operate in conjunction with the Tracking and Data Relay Satellite System; high-capacity, optical intersatellite links would be used to establish connectivity with other satellites for international data relay or data gathering. The requirements, scenarios, and satellite communications payload are examined along with the benefits of the concept and the payload technologies that must be developed.

Price, Kent M.↗
NASA NTRS2002

Validated Numerical Models for the Convective Extinction of Fuel Droplets (CEFD)

The NASA Nebraska Space Grant (NSGC) & EPSCoR programs have continued their effort to support outstanding research endeavors by funding the Numerical Simulation of the Combustion of Fuel Droplets study at the University of Nebraska at Lincoln (UNL). This team of researchers has developed a transient numerical model to study the combustion of suspended and moving droplets. The engines that propel missiles, jets, and many other devices are dependent upon combustion. Therefore, data concerning the combustion of fuel droplets is of immediate relevance to aviation and aeronautical personnel, especially those involved in flight operations. The experiments being conducted by Dr. Gogos and Dr. Nayagam s research teams, allow investigators to gather data for comparison with theoretical predictions of burning rates, flame structures, and extinction conditions. The consequent improved fundamental understanding of droplet combustion may contribute to the clean and safe utilization of fossil fuels (Williams, Dryer, Haggard & Nayagam, 1997, f 2). The present state of knowledge on convective extinction of fuel droplets derives from experiments conducted under normal gravity conditions. However, any data obtained with suspended droplets under normal gravity are grossly affected by gravity. The need to obtain experimental data under microgravity conditions is therefore well justified and addresses one of the goals of NASA's Human Exploration and Development of Space (HEDS) microgravity combustion experiment.

Gogos, George↗
NASA NTRS2002

Numerical Simulation of the Combustion of Fuel Droplets: Finite Rate Kinetics and Flame Zone Grid Adaptation (CEFD)

The NASA Nebraska Space Grant (NSGC) & EPSCoR programs have continued their effort to support outstanding research endeavors by funding the Numerical Simulation of the Combustion of Fuel Droplets study at the University of Nebraska at Lincoln (UNL). This team of researchers has developed a transient numerical model to study the combustion of suspended and moving droplets. The engines that propel missiles, jets, and many other devices are dependent upon combustion. Therefore, data concerning the combustion of fuel droplets is of immediate relevance to aviation and aeronautical personnel, especially those involved in flight operations. The experiments being conducted by Dr. Gogos and Dr. Nayagam s research teams, allow investigators to gather data for comparison with theoretical predictions of burning rates, flame structures, and extinction conditions. The consequent improved hndamental understanding droplet combustion may contribute to the clean and safe utilization of fossil hels (Williams, Dryer, Haggard & Nayagam, 1997, 72). The present state of knowledge on convective extinction of he1 droplets derives fiom experiments conducted under normal gravity conditions. However, any data obtained with suspended droplets under normal gravity are grossly affected by gravity. The need to obtain experimental data under microgravity conditions is therefore well justified and addresses one of the goals of NASA s Human Exploration and Development of Space (HEDS) microgravity combustion experiment.

Gogos, George↗
NASA NTRS1973

ATS-F Comsat Millimeter Wave Propagation Experiment

The ATS-F Comsat Millimeter Wave Propagation Experiment has been designed to gather statistical data on the attenuation caused by rain at millimeter wave frequencies. These data will be used to determine system design parameters for future communications satellite systems operating at frequencies above 10 GHz. The experiment has 39 ground terminals transmitting at 13.2 or 17.8 GHz to a transponder on board the ATS-F satellite. The transponder retransmits these signals at 4 GHz to a central earth terminal which records their amplitudes once each second. The data will be analyzed to provide probabilities of attenuation as functions of parameters such as rainfall, location, and time. These probabilities can then be used to determine the required power margins of millimeter wave communications systems. Techniques of overcoming severe attenuation such as site diversity and the use of a spot beam to increase the power level at selected locations will also be evaluated.

Westerlund, L. H.↗
NASA NTRS1990

Experiment design and operations

The objectives, design, and field operations of the First ISLSCP Field Experiment (FIFE) are described. The simultaneous acquisition of satellite, atmosphere, and surface data, and the understanding of the processes governing surface energy and mass exchange and how these are manifested in satellite-resolution radiometric data are identified as the specific objectives of the field-phase experiment. The central issues concerning the design of the field experiment are considered: the size of the site, the duration of the experiment, and the location of the site; it is noted that the Konza Prairie National Reserve was selected as the focus of the study. Field operations in 1987 and 1989 are discussed, and it is pointed out that a data set is available now from a single combined repository to all FIFE investigators, and that scientists can test models and algorithms on scales consistent with satellite observations and with enough supporting data on finer scales.

Sellers, P. J.↗
NASA NTRS1983

Data analysis for dual-polarized communication link experiments

The effect of the propagation medium on the performance of dual-polarized radio links operating in the microwave and millimeter wave regions is analyzed, with particular reference to rain and ice depolarization. Three methods of displaying measured cross-polarization discrimination (XPD) versus the attenuation (A) are examined: mean, median, and equiprobable. The mean and median values are shown to be essentially the same, while equiprobable data are sensitive to many errors. Ice depolarization alone or imbedded in rain depolarization can shift the entire XPD vs A relationship for equiprobable data. It is concluded that XPD vs A sets from different experiments can be compared with confidence when mean and median values are used. However, caution must be exercised with equipotential data sets, particularly when ice effects are involved.

Stutzman, W. L.↗
NASA NTRS2010

Telescience Support Center Data System Software

The Telescience Support Center (TSC) team has developed a databasedriven, increment-specific Data Require - ment Document (DRD) generation tool that automates much of the work required for generating and formatting the DRD. It creates a database to load the required changes to configure the TSC data system, thus eliminating a substantial amount of labor in database entry and formatting. The TSC database contains the TSC systems configuration, along with the experimental data, in which human physiological data must be de-commutated in real time. The data for each experiment also must be cataloged and archived for future retrieval. TSC software provides tools and resources for ground operation and data distribution to remote users consisting of PIs (principal investigators), bio-medical engineers, scientists, engineers, payload specialists, and computer scientists. Operations support is provided for computer systems access, detailed networking, and mathematical and computational problems of the International Space Station telemetry data. User training is provided for on-site staff and biomedical researchers and other remote personnel in the usage of the space-bound services via the Internet, which enables significant resource savings for the physical facility along with the time savings versus traveling to NASA sites. The software used in support of the TSC could easily be adapted to other Control Center applications. This would include not only other NASA payload monitoring facilities, but also other types of control activities, such as monitoring and control of the electric grid, chemical, or nuclear plant processes, air traffic control, and the like.

Rahman, Hasan↗
NASA NTRS2012

Space Environments and Effects Concept: Transitioning Research to Operations and Applications

The National Aeronautics and Space Administration (NASA) is embarking on a course to expand human presence beyond Low Earth Orbit (LEO) while expanding its mission to explore the solar system. Destinations such as Near Earth Asteroids (NEA), Mars and its moons, and the outer planets are but a few of the mission targets. NASA has established numerous offices specializing in specific space environments disciplines that will serve to enable these missions. To complement these existing discipline offices, a concept focusing on the development of space environment and effects application is presented. This includes space climate, space weather, and natural and induced space environments. This space environment and effects application is composed of 4 topic areas; characterization and modeling, engineering effects, prediction and operation, and mitigation and avoidance. These topic areas are briefly described below. Characterization and modeling of space environments will primarily focus on utilization during Program mission concept, planning, and design phases. Engineering effects includes materials testing and flight experiments producing data to be used in mission planning and design phases. Prediction and operation pulls data from existing sources into decision-making tools and empirical data sets to be used during the operational phase of a mission. Mitigation and avoidance will develop techniques and strategies used in the design and operations phases of the mission. The goal of this space environment and effects application is to develop decision-making tools and engineering products to support the mission phases of mission concept through operations by focusing on transitioning research to operations. Products generated by this space environments and effects application are suitable for use in anomaly investigations. This paper will outline the four topic areas, describe the need, and discuss an organizational structure for this space environments and effects application.

Edwards, David L.↗