Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Flash electropolishing for TEM: Reducing FIB‐induced defects in tungsten with protocols for new materials

Focused ion beam (FIB) milling has become the dominant approach for site-specific transmission electron microscopy (TEM) specimen preparation; however, FIB damage remains a critical limitation for reliable microstructural characterisation, particularly in radiation effects studies. Tungsten is especially susceptible to FIB damage due to its high nuclear stopping power, which promotes the formation and strong diffraction contrast of FIB-induced ‘black spot’ defects that are indistinguishable from very fine irradiation-induced loops/defects resulting from low to intermediate temperature neutron irradiation. In this work, flash electropolishing is systematically evaluated as a post-FIB treatment for minimising preparation-induced artefacts for TEM analysis of tungsten-based alloys. Using a range of non-, ion-, and neutron-irradiated tungsten materials, the effectiveness of flash electropolishing has been assessed through direct comparison with conventional FIB and plasma-FIB preparation including low-energy Ga, Ar, Xe ion cleaning. The results demonstrate that flash electropolishing effectively removes FIB-damaged layers and ‘black spot’ defects, thereby enabling reliable observation of irradiation-induced dislocation structures. Key processing parameters governing flash electropolishing quality – including lamella thickness, applied voltage, polishing duration, electrolyte chemistry, and cathode geometry – have been systematically evaluated, and clear criteria were established for determining when flash electropolishing is required to ensure reliable microstructural analysis. This work also provides practical guidance for implementing flash electropolishing as an artefact-controlled specimen-preparation approach for TEM characterisation of FIB-produced specimens. The systematic protocol can be extended to other, non-tungsten materials.

TEM sample preparation↗
DOE OSTI2024

Environmental barrier coatings on SiC without a silicon bond coating: oxidation resistance, failure modes, and future improvements

Environmental barrier coatings (EBCs) are used to mitigate chemical reactions between SiC ceramic matrix composite (CMC) components and the H 2 O in combustion gas in turbine hot sections. CMCs are currently temperature-limited by the Si-bond coating, which melts at ~ 1414 °C. This work explores EBCs where the bond coating was removed to achieve higher operating temperatures. Various versions of enhanced roughness SiC were utilized to improve EBC adhesion to the substrates prior to 1 h furnace cycle testing in steam at 1250–1425 °C. The enhanced SiC roughness resulted in short coating lifetimes as the roughness was oxidized away with SiO 2 formation. Further, isothermal furnace exposures at 1400–1600 °C showed Yb 2 Si 2 O 7 /Yb 2 SiO 5 EBC microstructural changes, resulting in premature debonding from the substrates. Finally, this work provides baseline requirements for the development of both next-generation EBCs and bond coating strategies to overcome the current limitation of the Si-bond coating melting temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding solidification of near eutectic alloy using Cellular Automata (CA)

The solidification microstructure of an alloy strongly influences the mechanical properties. Dendritic and eutectic solidification are two important pathways of alloy solidification. The formation of phases, and their size and distribution depend on which pathway to take. In contrast to the Scheil model that has been widely used in describing the solidification pathways of alloys manufactured from conventional casting approach, more sophisticated solidification models are required to describe the state-of-the art manufacturing processes, such as additive manufacturing where distinctly different phase morphology, size and distribution than conventional casting can form, due to the vast difference in cooling conditions. Therefore, this work is to develop a computational Cellular Automata framework which includes the modeling of nucleation and growth of dendritic and eutectic solidification, as well as their competition as a function of alloy composition, undercooling and cooling rate. Further, after individual solidification models were validated against analytical solutions, the models were then combined to predict the competition between dendritic and eutectic solidification in alloys with off-eutectic compositions. This work predicts increased cooling rates suppress the dendritic solidification and promote eutectic solidification. Although quantitative validation is needed, this finding is consistent with qualitative observation in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nonequilibrium spherulitic magnetite in the Ryugu samples

Here, we have investigated several particles collected during each of two touchdowns of the Hayabusa2 spacecraft at the surface of the C-type asteroid 162173 Ryugu using various electron microscope techniques. Our detailed transmission electron microscopy study shows the presence of magnetite with various morphologies coexisting in close proximity. This is characteristic of CI chondrite-like materials and consistent with the mineral assemblages and compositions in the Ryugu parent body. We describe the microstructural characteristics of magnetite with different morphologies, which could have resulted from the chemical conditions (growth vs. diffusion rate) during their formation. Furthermore, we describe the presence of magnetites with a spherulitic structure composed of individual radiating fibers that are characterized by pervasive, homogeneously distributed euhedral to subhedral pores that have not been described in previous chondrite studies. This particular spherulitic structure is consistent with crystallization under nonequilibrium conditions. Additionally, the presence of a high density of defects within the magnetite fibers, the high surface/volume ratio of this morphology, and the presence of amorphous materials in several pores and at the edges of the acicular fibers further support their formation under nonequilibrium conditions. We suggest that the growth processes that lead to this structure result from the solution reaching a supersaturated state, resulting in an adjustment to a lower free energy condition via nucleation and rapid growth.

58 GEOSCIENCES↗
DOE OSTI2026

High hardness and oxidation-resistant Cr-containing medium entropy ZrTaW diboride

This study reports the successful synthesis of a Cr-containing (Zr 0.30 Ta 0.34 Cr 0.06 W 0.30 )B 2 medium-entropy boride (MEB) via an in-situ reactive borothermal reduction route from oxide precursors. High-energy ball milling was employed to homogenize the precursor mixture prior to reactive densification. X-ray diffraction confirmed the formation of a predominantly AlB₂-type hexagonal diboride structure together with a secondary (W X , M 1-X )B monoboride phase. Microstructural characterization revealed compositional heterogeneity and localized W-rich regions associated with the secondary phase. The synthesized medium-entropy boride exhibited enhanced mechanical properties, which are attributed to lattice distortion and solid-solution strengthening effects. Thermogravimetric analysis revealed complex multistage oxidation behavior, and the oxidation resistance was compared with conventional ultra-high-temperature diborides. The results demonstrate the strong relationship between oxide-derived processing, compositional complexity, phase evolution, and oxidation behavior, highlighting the potential of medium-entropy borides for high-temperature structural applications

36 MATERIALS SCIENCE↗
DOE OSTI2022

Molecular dynamics studies of grain boundary mobility and anisotropy in BCC γ-uranium

Grain morphologies such as grain size and aspect ratio in uranium-based metallic fuels are important microstructural features that can impact various fuel performance properties such as fission-gas-induced swelling, thermal transport, high burnup structure formation, and radiation resistance. Accurate prediction of the fuel grain morphologies requires knowledge of critical grain growth parameters such as grain boundary (GB) mobility and anisotropy. In this work, molecular dynamics simulations were performed to study the GB mobility and its anisotropy in pure body-centered-cubic (BCC) γ uranium. Nine GBs with different combinations of misorientation angles (20°, 30°, 45°) and rotation axes (<100>, <110>, <111>), as well as an additional <111> 38.2° GB were studied using three interatomic potentials. Here, it is found that the GB mobility anisotropy has complex trends, depending on both rotation axis and misorientation. However, in general the <110> rotation axis has the fastest GB mobility at the same misorientation. The results of this work can be used as not only baselines for future studies of GB mobility in uranium-based alloys such as uranium-molybdenum (U-Mo) fuels, but also input for mesoscale modeling of grain growth in uranium-based alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Analyzing the effect of pressure on the properties of point defects in $\gamma\mathrm{U–Mo}$ through atomistic simulations

Uranium–molybdenum (U–Mo) alloys in monolithic fuel foil are the primary candidate for the conversion of high-performance research reactors in the USA. Monolithic fuel is utilized in a plate-type design with a zirconium diffusion barrier and aluminum cladding. These fuel types are unique in that they contain no plenum for the release of fission gases, which, in conjunction with the aluminum cladding, can lead to large stress states within the fuel. The nature of how fundamental processes of radiation damage, including the evolution of point defects, under such stresses occur is unknown. In this work, we present molecular dynamics simulations of the formation energy of point defects under applied stress. We report this work will allow for the implementation of stress-dependent microstructural evolution models of nuclear fuels, including those for both fission gas bubble growth and creep, which are critical to ensure the stable and predictable behavior of research reactor fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Spatial mapping of the localized corrosion behavior of a magnesium alloy AZ31B tungsten inert gas weld

Sections of a magnesium alloy, AZ31B, joined with tungsten inert gas (TIG) welding, were examined with scanning electrochemical microscopy (SECM) and scanning Kelvin probe force microscopy (SKPFM) to investigate corrosion mechanisms by correlating observed corrosion behavior with weld-affected microstructural variations. Insight into the changing nature of the galvanic couples between weld zones and at localized microgalvanic sites were investigated using SECM and SKPFM to map both electrochemically active regions and Volta potential differences across the weld-affected zones. The formation of an Al-Zn solidification network in the fusion zone (FZ) at and near the TIG weld epicenter differs from the outer heat-affected zone (HAZ), where intermetallic particles (IMPs) are the notable secondary phase from the magnesium matrix. These microstructures were mapped with SKPFM before and after brief exposure to a salt solution, revealing micro-galvanic couples as the main driving force to corrosion initiation and propagation within each zone. The IMPs and Al-Zn solidification network act as strong cathodes and govern the corrosion processes. The galvanic coupling and evolution of the intrinsic corrosion behavior between the weld zones is explained by monitoring the hydrogen evolution reaction (HER) with SECM over time. Anodically induced cathodic activation is confirmed for this welded material, as micro-galvanic couples between microstructural features are found to transition over time to broad electrochemically active areas within the weld-affected zones, resulting in polarity reversal as time of exposure proceeds.

Anodically induced cathodic activation↗
DOE OSTI2026

Dynamic compression and spallation behavior of NbTaTiVZr high-entropy alloy

High-entropy alloys are a new class of materials with promising properties for aerospace and defense applications. The unique behavior of these materials is driven by the complex interactions between dissimilar atoms in a crystal and requires combined theoretical and experimental efforts to unlock their full potential. Here, we evaluate the relationship between the microstructure and the dynamic response of the equiatomic NbTaTiVZr alloy. Specifically, the shock Hugoniot, or equation of state, was measured up to a particle velocity of 0.5 mm μs −1 using gas gun plate impacts. Shock wave profile and incipient spallation experiments were used to characterize wave propagation and damage formation with post-mortem recovery experiments. Molecular dynamics simulations confirm the experimental findings and extend them up to 2.1 mm μs −1 particle velocity. Computational thermodynamic calculation of phase diagram simulations explain details of the material microstructure, which explains the measured strength and experimental damage patterns. Overall, this work provides detailed high-strain-rate characterization of a refractory high-entropy alloy, and more importantly, a framework and demonstration of the utility and necessity of a combined theoretical and experimental approach, outlining the importance of considering processing and manufacturing conditions when evaluating the performance of new materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development and performance of INCONEL® alloy 740H® seam-welded piping

INCONEL® alloy 740H® is an age-hardenable nickel-based alloy approved for pressure vessels and piping within ASME Section I, VIII, and B31.1. Currently, the code applies a weld strength reduction factor (WSRF) of 0.7 to the allowable stresses for longitudinal seam welds in the time dependent creep regime. In this work, a full-scale seam weld was successfully produced using typical industrial practices. The component was solution heat-treated and aged after fabrication to improve the performance of the weldment. Tensile, bend, impact, and low-cycle fatigue tests showed the component met all the specification requirements and elevated temperature properties were within base metal expectations with failures predominately in the weld metal. Long-term creep tests, including large samples more representative of the entire weldment, were fabricated and tested to times in excess of 10,000 h at multiple temperatures. Analysis of the creep data supports a WSRF of 0.9 for the solution annealed + aged weldments in contrast to the WSRF of 0.7 currently applied to welded + aged weldments. Metallurgical analysis shows that the solution annealing causes recrystallization of the weld metal and reduces the chemical compositional and microstructural gradients in the weldments resulting in acceptable short-term performance. In long-term creep, evidence for coarsened zones in the weldments due to discontinuous coarsening reactions were identified as the mechanism leading to accelerated creep damage formation in the weld metal and sample failure.

14 SOLAR ENERGY↗
DOE OSTI2023

Additive manufacturing enabled synergetic strengthening of bimodal reinforcing particles for aluminum matrix composites

An additive manufactured TiB 2 /Al-Cu-Mg-Ni composite with a minor amount of Sc was fabricated by laser powder bed fusion (LPBF). The composite shows a yield strength of ~370 MPa, almost doubling the strength of its wrought matrix counterpart, and an elongation of ~7 %. The superior mechanical properties are attributed to a unique micro-nano hierarchical microstructure, consisting of nanoscale and microscale TiB 2 particles dispersed in a matrix of fine aluminum grains (3 µm) together with intragranular intermetallic nanoparticles and nano-cellular networks (cell size 30 nm). The formation of the TiB 2 nanoparticles is the consequence of partial dissolution of the TiB 2 particulates and the enrichment of Sc in the newly formed nanoparticles. Remarkable strengthening effects are achieved by the bimodal TiB 2 particles, intermetallic nanoparticles and intragranular nano-cellular networks. Finally, this study provides new insights into the role of additive manufacturing in tailoring the microstructure of particulate reinforced metal matrix composites (MMCs) with advanced properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal generation, manipulation and thermoelectric detection of skyrmions

The efficient generation, manipulation and detection of magnetic skyrmions are important for the development of future spintronic devices. One approach is to use electric-current-induced spin torques. Recently, thermally induced skyrmion motion has also been observed, but wider experimental evidence and its capabilities remain limited. Here we report the thermal generation, manipulation and thermoelectric detection of nanoscale skyrmions in microstructured metallic multilayers integrated with on-chip heaters. The local application of heat can facilitate a domain morphological transition and the formation of skyrmions at the device edge, where a low energy barrier exists. Here, we observe the unidirectional diffusion of skyrmions from hot regions to cold regions, which is due to the interplay among the repulsive forces between skyrmions, thermal spin–orbit torques, entropic forces and magnonic spin torques. The thermally generated skyrmions can also be electrically detected via the Nernst voltage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Failure analysis of solid oxide fuel cells nickel-yttria stabilized zirconia anode under siloxane contamination

In this study, the failure process of the solid oxide fuel cell (SOFC) Ni-yttria-stabilized zirconia (YSZ) anode is investigated with D4 siloxane (octamethylcyclotetrasiloxane) contamination. In order to evaluate the influence of the electrochemical reaction on the siloxane deposition process, the SOFC experiments were operated at open circuit voltage (OCV) and 50 mA cm -2 conditions at 800°C. During the failure process, electrochemical, morphology and exhaust gas component analysis testing are conducted at the critical points. An equivalent circuit model and corresponding microstructure parameter calculations for separated physicochemical processes were utilized for the quantitative analysis of the failure process. Further, the results confirm the siloxane chemical adsorption deposition mechanism proposed in previous work. As a result, the failure of the anode was attributed to the gas diffusion blockage by dense silicon dioxide layer formation. The anode failure process with siloxane contamination is faster when the anode is operated under polarization.

25 ENERGY STORAGE↗
DOE OSTI2026

Microstructure, Transport, and Mechanics of Compacted Clay Simulated at the 0.1 μm Scale (1400 Smectite Clay Particles) Using a Coarse-Grained Model with Explicit Counterions

Clay-rich geomaterials play a critical role in many subsurface systems. The macroscale properties of these materials (low permeability, high ionic conductivity, high swelling pressure, etc.) are sensitive to molecular-level adsorption and hydration interactions at clay−water interfaces. Efforts to develop multiscale simulation approaches to predict these properties reveal a scale gap between atomistic simulations (typically limited to systems smaller than 10 nm) and continuum-scale models (which use computational grid elements with dimensions ≳ 10 μm). In this study, we present a coarse-grained (CG) framework that partly bridges this gap by simulating compacted smectite clay assemblages with dimensions of 0.1 μm containing 1,400 clay particles across a range of dry densities (1,050 to 1,850 kg·m −3 ) and Na/Ca counterion compositions (Na fraction ranging from 0.2 to 1). The simulated systems, along with their reconstructed binary three-dimensional pore networks, are used to evaluate the microstructure, pore size distribution, tortuosity, ion diffusivity, and swelling pressure of compacted smectite clay. Results show that our approach captures important features of the mesoscale heterogeneity of compacted clays, including tactoid formation, hierarchical porosity, and anisotropic pore networks. Results also reveal how compaction and counterion composition govern emergent behaviors, including dominant pore sizes, directional transport, and electrochemical response. This work highlights the potential of CG simulations to bridge molecular and continuum scales and to advance geotechnical and environmental applications involving clay-rich materials as well as related nanoporous media such as geopolymers and calcium-silicate-hydrate. However, the results also suggest that accurate prediction of certain microstructural and mechanical properties (e.g., swelling pressure) may require even larger-scale systems on the order of 1 μm.

02 PETROLEUM↗
DOE OSTI2020

Effects of heat treatment and build orientation on the evolution of $ϵ$ and $α'$ martensite and strength during compressive loading of additively manufactured 304L stainless steel

In this paper, the effect of heat-treatment and build orientation on martensitic phase transformation in additively manufactured (AM) 304L stainless steel is studied and compared with conventionally produced wrought material. The relationships between observed martensitic transformations and material microstructures and their effects on mechanical strength are established through experimental observations. In situ high-energy X-ray powder diffraction measurements were performed to monitor the evolution of $ϵ$ and $α'$ martensite during compressive loading of stainless steel. Electron backscatter diffraction (EBSD) was used to provide insight on initial grain morphology, crystallographic misorientation within grains, and crystallographic texture. Heat treatment alters the microstructure of AM samples creating different initial conditions. This difference in starting microstructure resulted in variability in martensitic transformation during compressive deformation. The rate of martensitic transformation decreased for AM samples treated with temperatures up to 1100°C, after which the AM microstructures recrystallized, resulting in increased rate of martensitic transformation for those samples treated at higher temperatures. It was also observed that aligning the axis of compression with the AM build direction resulted in a lower rate of strain-induced martensite formation as opposed to aligning the compression axis perpendicular to it. More favorable distribution of crystal orientations in the latter loading orientation promoted martensitic transformation. These and additional experimental observations from EBSD in terms of kernel average misorientation, mean grain orientation spread, and mean crystallite size reveal strong microstructural effects on strength of additively manufactured metallic materials.

304L stainless steel↗
DOE OSTI2020

Imaging broadband soft X-ray transmission-grating spectrograph for a wavelength range λ > 111 Å

A family of aperiodic Mo/Be multilayer mirrors was designed for maximum uniform reflectivity in the ranges 111 – 138, 111 – 150, 111 – 200 and 111 – 222 Å at normal radiation incidence. The simulations took into account the existence of Mo-on-Be and Be-on-Mo transition layers. It was shown that the reflectivity may be as high as 10% in an octave wavelength range of 111 – 222 Å. We demonstrate the operation of an imaging transmission-grating spectrograph with a broadband Mo/Be multilayer mirror with a uniform reflectivity in the wavelength range 111 – 138 Å synthesised at the Institute for the Physics of Microstructures, RAS. The spectrograph was used to record the line spectra of multiply charged fluorine and magnesium ions from a laser-produced plasma. The role of the grating support structure in the formation of spectral source images is discussed. The spatial resolution of 50 μm is demonstrated. (laser applications and other topics in quantum electronics)

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of thermal aging on microstructure and crack growth response of Alloy 152 weld

Nickel-based Alloy 690 and the associated weld Alloys 52 and 152 are typically used for nozzle penetrations in replacement heads for pressurized water reactor (PWR) vessels, because of their excellent overall resistance to general corrosion and environmental degradation, primarily stress corrosion cracking (SCC). However, many of the existing PWRs are expected to operate for 40-80 years. Likewise, advanced water-cooled small modular reactors (SMRs) will use Ni-Cr alloys and are expected to receive initial operating licenses for 60 years. Hence, the thermal stability of Ni-Cr alloys is a potential concern for the long-term performance of both existing and advanced nuclear power plants, and possibly spent fuel storage containers. The objective of this research is to understand the microstructural changes occurring in high-Cr, Ni-based Alloy 152 weldments during long time exposure to the reactor operating temperatures, and the effect of these changes on the service performance. One area of particular concern is the potential for long range ordering (LRO), i.e. formation of the intermetallic Ni2Cr phase under prolonged exposure to reactor temperatures and/or irradiation, which can increase strength, decrease ductility, and cause dimensional changes or lead to in-service embrittlement of components made with these alloys. Hence, this research focused on the microstructural evolution and the SCC response of Alloy 152 under accelerated thermal aging. The materials studied involved three heats of Alloy 152 used to produce a dissimilar metal weld (DMW) joining an Alloy 690 plate to an Alloy 533 low alloy steel (LAS) plate, thermally aged at three different temperatures (370°C, 400°C and 450°C) for up to 75,000h (equivalent to 60 years of service). The microstructural characterization by means of synchrotron X-ray did not find evidence of LRO in any of the three heats aged to an equivalent of 60 years of service. Testing in a primary water environment of a heat of Alloy 152 aged at 370°C to a 60-year service equivalent revealed a fatigue and corrosion fatigue crack growth responses similar to those measured on the un-aged alloy. However, the SCC CGR response of the aged sample appears to show a deterioration in performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗