SEARCH · Engineering Papers

Results for “Material failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography (μCT) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μCT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. Further, a new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Fracture mechanics approach to TRISO fuel particle failure analysis

Weibull stress-based methods for failure probability assessment have been developed and analyzed to assess the integrity of tristructural isotropic (TRISO) fuel particles during fuel life cycles and accident operating conditions. While simple, these methods entail a number of drawbacks when stress concentrates near crack tips, including finite element mesh size dependency when the Weibull stress is averaged over the finite element domain. Fracture mechanics approaches involving the use of interaction integrals eliminate this lack of mesh convergence and produce consistent fracture predictions. In this work, we use an interaction integral approach to computing stress intensity factors for a crack in the inner pyrolytic carbon layer perpendicular to the silicon carbide layer, which is simplified representation of a failure mode in TRISO particles. Further, the interface between these two TRISO layers has been shown to become porous, which we simulate by considering a transition of mechanical properties over such porous length, i.e. the layers are modeled as a functionally graded material. Aspects such as porosity and thermal and irradiation eigenstrains are considered in computing the stress intensity factor from a fracture mechanics approach and compared with the known Weibull stress failure approach. The methodology introduced in this paper enables a more general fracture probability assessment in TRISO particles and eliminates the need to identify best suited parameters when using local or averaged stress-based failure criterion. Finally, the numerical sensitivity studies show how parameters such as the porous transition zone length, the material stiffness, and creep affect the probability of TRISO fuel particle failure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Critical differences between electron beam melted and selective laser melted Ti-6Al-4 V

Effective optimization of the production of Ti-6Al-4 V using AM requires a fundamental understanding of the relative importance of different microstructural features to the deformation and failure mechanisms, particularly features that vary between production methods. In this study, the tensile response and deformation mechanisms of electron beam melted (EBM) AM Ti-6Al-4 V material loaded in different orientations and produced using various powder sizes were compared to those of selective laser melted (SLM) AM Ti-6Al-4 V material. The density and morphology of pores, phase fractions, prior-β grains, and defect microstructures were evaluated using scanning electron microscopy, X-ray computed tomography, electron backscatter diffraction, and transmission electron microscopy before and after deformation. The results were used to evaluate the relative importance of each feature on strengthening, deformation, and failure initiation mechanisms. Results focused primarily on coarse-powder EBM materials indicated that phase distribution and defect density were most influential for determining material yield strength as well as maximum possible strain to failure. Porosity was lower overall in EBM Ti-6Al-4 V than in SLM, allowing for occasional increases in part strain to failure, but remained a limiting factor determining overall part ductility.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 6061-T651 Aluminum Alloy from Plate

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The matters of interest here are the elastic-plastic response and ductile failure behavior of 6061-T651 aluminum alloy under the conditions described above. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of a modular $J_2$ plasticity model with isotropic hardening as well as a ductile failure model. Both included modules that accounted for temperature and strain rate dependence. The models were coupled with an adiabatic heating module to calculate the temperature rise due to the conversion of plastic work to heat. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s as well as four geometries of notched tension specimens and two tests on specimens with shear-dominated deformations. The test data collected allowed the calibration of both the plasticity and the ductile failure models. Most test specimens were extracted from a single piece of plate to maintain consistency. Notched tension tests came from a possibly different plate, but from the same lot. When using the model in structural finite element calculations, element formulations and sizes different from those used to model the test specimens in the calibration are likely to be used. A brief investigation demonstrated that the failure model can be particularly sensitive to the element selection and provided an initial guide to compensate in a specific example.

36 MATERIALS SCIENCE↗

DOE OSTI2025

A Robust Data-Driven Approach for Mechanical Serial Sectioning

Mechanical serial sectioning (MSS) provides detailed microstructural information across large length scales. By repeatedly removing thin layers of material and imaging the exposed surface, a 3D representation of a specimen’s internal structure can be constructed, enabling failure analysis and feature identification that are otherwise inaccessible via conventional 2D or nondestructive evaluation techniques. Achieving consistent and accurate material removal can be challenging due to system variability, requiring an experienced operator to manually adjust parameters, prolonging data collection times and necessitating post-processing routines to standardize the data. Here, to address these challenges, this paper presents the employment of a one-step model predictive control (MPC) framework tailored to a run-to-run (R2R) controller. The R2R-MPC controller automates the parameter selection process, improving the consistency of material removal through iterative feedback for disturbance rejection and accurate tracking of the target removal rate. Using a data-driven approach, the controller robustly adapts to changing material characteristics. The effectiveness of the R2R-MPC controller is demonstrated through simulation and experimental results and compared to previous data collection procedures.

3D Materials Science↗

DOE OSTI2025

Durability Research Is Pivotal for Perovskite Photovoltaics

Metal halide perovskite solar cells have shown promising power conversion efficiencies, but commercialization requires that decent durability is also demonstrated. Under normal operation, solar cells are subject to a complex combination of stressors, such as visible light, ultraviolet light, heat, humidity, mechanical stress and electric potential, which complicates the understanding of failure mechanisms. Existing stress tests do not act as a time machine. In new materials systems such as perovskite photovoltaics, the tests have no known relationship to field service. In this Perspective we recommend following a durability learning cycle that interleaves photovoltaic module engineering with field testing; accelerated testing; and preconditioning and performance engineering. We advocate for field testing to demonstrate real-world performance and identify field-relevant failure modes, and urge the community to develop accelerated and qualification tests that account for device metastability, variations in material composition and different/various processing methods. In conclusion, these practices are more difficult, but more important, than the simple pursuit of higher initial efficiencies.

14 SOLAR ENERGY↗

DOE OSTI2025

Non-destructive electrochemical diagnosis of failure mechanisms in aqueous zinc batteries

The early detection of secondary reactions that affect the life and performance of zinc manganese oxide batteries requires a shift from conventional time-consuming and often destructive procedures to rapid lifetime-predictive techniques. In this work, an electrochemical approach is employed to elucidate independent signatures for four common types of failure mechanisms in zinc manganese dioxide (Zn||MnO2) batteries—namely, the loss of zinc inventory, the loss of active material at the cathode, electrolyte depletion, and increased cell impedance. Our findings, specific to coin cell configurations, reveal that each induced failure mechanism can be distinctively modeled and identified based on responses from the rest voltage and columbic-efficiency data for prompt detection. For instance, electrolyte depletion response manifests a distinctive abrupt (>80 %) decrease in columbic efficiency (CE) and charge-rest voltage (Vc) while the discharge-rest voltage remained constant at ~1.3 V. Furthermore, electrolyte rejuvenation of the cell increased the CE to >95 % and restored Vc from ~0.3 to >1.7 V. Recovery experiments and reference performance tests demonstrated consistency between electrochemical descriptors and their associated failure mechanisms. Further, the outcomes of this work provide valuable insights and data models for some of the dominant failure mechanisms present in zinc manganese battery chemistries, which are beneficial to accelerated early-lifetime diagnosis and advancement of Zn batteries development.

25 ENERGY STORAGE↗

DOE OSTI2024

Brittle failure analysis and modeling of high-burnup PWR fuel cladding alloys

The aim of this research is the development of methods for predicting mechanical behavior and identification of limiting conditions to prevent brittle failure of high-burnup (HBU) pressure water reactor (PWR) fuel cladding alloys. A finite element (FE) model of the ring compression test (RCT) was created to analyze the failure behavior of zirconium-based alloys with radial hydrides during the RCT. An elastic-plastic material model describes the zirconium alloy. The stress-strain curve needed for the elastic-plastic material model was derived by inverse finite element analyses. Cohesive zone modeling is used to reproduce sudden load drops during RCT loading. Based on the failure mechanism in non-irradiated ZIRLO (R) claddings, a micro-mechanical model was developed that distinguishes between brittle failure along hydrides and ductile failure of the zirconium matrix. Two different cohesive laws representing these types of failure are present in the same cohesive interface. The key differences between these constitutive laws are the cohesive strength, the stress at which damage initiates, and the cohesive energy, which is the damage energy dissipated by the cohesive zone. Statistically generated matrix-hydride distributions were mapped onto the cohesive elements and simulations with focus on the first load drop were performed. Computational results are in good agreement with the RCT results conducted on high-burnup M5 (R) samples. It could be shown that crack initiation and propagation strongly depend on the specific configuration of hydrides and matrix material in the fracture area.

Simbruner, Kai↗

DOE OSTI2022

Efficient high-fidelity TRISO statistical failure analysis using Bison: Applications to AGR-2 irradiation testing

The ability of tri-structural isotropic (TRISO) fuel to contain fission products is largely dictated by the quality of the manufacturing process, since most of the fission product release is expected to occur due to coating layer failure in a small number of particles containing defects. The Bison fuel performance code has capabilities to predict failure in individual particles, accounting for the presence of defects, and to apply statistical analysis methods to compute the probability of failure in a set of fuel particles. Bison has recently undergone significant development both to improve its physical representations of fuel particle behavior and to improve the efficiency of its statistical failure calculations. Physical model improvements include new capabilities to account for the pressure generated by fission gases on inner pyrolytic carbon (IPyC) crack surfaces and to use local material coordinate orientation to accurately incorporate the anisotropy in the material properties in aspherical particles. To improve statistical modeling efficiency, a direct integration approach which involves directly integrating the failure probability function associated with statistically varying parameters has been developed. The direct integration approach is much more efficient than the Monte Carlo (MC) schemes commonly employed, and allows Bison to directly run high-dimensional fuel performance models, which improves the accuracy of failure probability calculations. Finally, a set of benchmark problems is considered here to compare the MC and direct integration approaches, and a statistical failure analysis of compacts in the Advanced Gas Reactor (AGR)-2 experiments is performed using the direct integration approach.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Carburization Kinetics of Zircalloy-4 and Its Implication for Small Modular Reactor Performance

Carburization of cladding materials has long been a concern for the nuclear industry and has led to the restricted use of high-thermal conductivity fuels such as uranium carbides. With the rise of small modular reactors (SMRs) that frequently implement a graphite core-block, carburization of reactor components is once more in the foreground as a potential failure mechanism. To ensure commercial viability for SMRs, neutron-friendly cladding materials such as Zr-based alloys are required. In this work, the carburization kinetics of Zircaloy-4 (Zry-4), for the temperature range 1073–1673 K (covering typical operating temperatures and off-normal scenarios) are established. The following Arrhenius relationship for the parabolic constant describing ZrC growth is derived: Kp (in μm2/s) = 609.35 exp(−1.505 × 105/RT)). Overall, the ZrC growth is sluggish below 1473 K which is within the operational temperature range of SMRs. In all cases the ZrC that forms from solid state reaction is hypo-stoichiometric, as confirmed through XRD. The hardness and elastic modulus of carburized Zry-4 are also examined and it is shown that despite the formation of a ZrC layer, C ingress in the Zry-4 bulk does not impact the mechanical response after carburization at 1073 K and 1473 K for 96 h.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Polyester functional graphenic materials as a mechanically enhanced scaffold for tissue regeneration

Traditional metal implants such as titanium, cobalt, and chromium have found wide utility in medicine; however, these come with a risk of toxicity. To overcome metal-related toxicity and enable degradability, polyesters including polycaprolactone (PCL), polylactic acid (PLA), and polyglycolic acid (PGA) show promise for the replacement of various biomedical applications of metals due to their accepted biocompatibility and FDA approval. However, polyesters are less stiff than their metallic counterparts, limiting their application to non-load bearing injury sites, such as fixation hardware for fingers. To improve mechanical properties, graphene oxide (GO)-polyester composites are a promising class of biodegradable scaffolds. Initial reports of these composites are encouraging, but mechanical properties still fall short. Traditional composites rely on non-covalent association between GO and the polyesters, which often leads to failure at the interface and weakens the overall strength of the material. Herein, we present a strategy for attachment of these FDA-approved polyesters onto a derivative of GO using a robust covalent bond. By covalently functionalizing the graphenic backbone with polyesters and without metal catalysts, we create functional graphenic materials (FGMs) to not only simultaneously retain biodegradability and compatibility, but also mechanically strengthen PCL, PLA, and PGA; we observed an average increase in the Young's modulus of over 140% compared to the graphenic backbone. These polyester-functionalized FGMs are a promising platform technology for tissue implants.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

Synergistic Effects of Molten Salt Corrosion and Proton Irradiation on Grain Boundary Strength in Ni-20Cr

Nickel-based alloys are leading contenders for use as structural materials in molten salt reactors. While there have been extensive studies on the impact of fluoride/chloride-based molten salt corrosion on the microstructural evolution of various nickel-based alloys, the effects of simultaneous molten salt corrosion and radiation on the mechanical integrity of grain boundaries (GBs) remain underexplored. In this study, we use a Ni-20Cr model alloy to investigate this issue, subjecting it to simultaneous molten fluoride salt corrosion and proton irradiation. We performed cross-sectional and chemically-sensitive electron microscopy characterization of the microstructures of these materials, identifying the characteristic corrosion-induced microstructure and local chemical heterogeneity near GBs. After developing a sample preparation method for reliable characterization of GB strength, we assess the mechanical degradation of GBs using in situ push-to-pull micro tensile tests. Our findings reveal that voids induced by corrosion are the primary influence on the failure mode of GBs, regardless of whether proton irradiation is present. For materials that exhibit ductile fracture, those subjected to simultaneous corrosion and radiation exhibit lower yield strengths than those exposed to corrosion alone, which may be linked to the previously observed phenomenon of proton irradiation-decelerated intergranular corrosion in molten salt.

36 - MATERIALS SCIENCE↗

DOE OSTI2020

Developing Materials for Extreme Environments and Their Use in Nuclear Waste Canisters and Reactors - 20559

The paper focuses on the development of materials which can be utilized in extreme industrial environments. The paper discusses the advancement of materials and their application in components which are utilized in extreme industrial environments as such that of the nuclear field and especially in the nuclear waste field. Nuclear power plants have become an indispensable part of the electricity generation, medical, food processing and many other industries. Though burning small amount of fuel as compared to conventional power plants, they also create waste which is not easy to handle as other types of wastes. The nuclear waste sitting at the bottom of spent fuel tanks around the globe has raised public concerns on how it will be dealt with. Europe has started to give an answer by working on geological repositories. Though till yet, waste has been cooled in spent fuel tanks and after processing, is precisely placed in nuclear waste canisters and casks and transported to sites across the country for further cooling and storage. Though in all this process there had been a great deal of advancement on the type of casks and canisters used and the processes for transporting nuclear material and waste. Often reports about radioactive material leakage, moisture content inside barrels etc. has surfaced. Be it official or unofficial report, there seems a technical failure on how the nuclear waste has been stored and placed at facilities around the globe. The other aspect of this material development is to be beneficial for nuclear reactors. As the technology gets advanced, nuclear reactors change their titles from Gen II to Gen III and so on. The new fleet of upcoming reactors will be exceptionally safer, reliable and more efficient. But these benefits will also bring drawbacks with them. As these reactors will operate at high temperature (above 800 degree Celsius) they also ask for advancement in materials used in the reactor core, fuel used, reactor control etc. The paper tries to answer such concerning questions. The work shows the study done on different material that can be better candidates for extreme environments. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Unveiling the Fatigue Behavior of 2D Hybrid Organic–Inorganic Perovskites: Insights for Long-Term Durability

2D hybrid organic–inorganic perovskites (HOIPs) are commonly found under subcritical cyclic stresses and suffer from fatigue issues during device operation. However, their fatigue properties remain unknown. Here, the fatigue behavior of (C 4 H 9 -NH 3 ) 2 (CH 3 NH 3 ) 2 Pb 3 I 10 , the archetype 2D HOIP, is systematically investigated by atomic force microscopy (AFM). It is found that 2D HOIPs are much more fatigue resilient than polymers and can survive over 1 billion cycles. 2D HOIPs tend to exhibit brittle failure at high mean stress levels, but behave as ductile materials at low mean stress levels. These results suggest the presence of a plastic deformation mechanism in these ionic 2D HOIPs at low mean stress levels, which may contribute to the long fatigue lifetime, but is inhibited at higher mean stresses. The stiffness and strength of 2D HOIPs are gradually weakened under subcritical loading, potentially as a result of stress-induced defect nucleation and accumulation. The cyclic loading component can further accelerate this process. The fatigue lifetime of 2D HOIPs can be extended by reducing the mean stress, stress amplitude, or increasing the thickness. These results can provide indispensable insights into designing and engineering 2D HOIPs and other hybrid organic–inorganic materials for long-term mechanical durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Automatically adaptive stabilized finite elements and continuation analysis for compaction banding in geomaterials

Under compressive creep, viscoplastic solids experiencing internal mass transfer processes can accommodate singular cnoidal wave solutions as material instabilities at the stationary wave limit. These instabilities appear when the loading rate is significantly faster than the material's capacity to diffusive internal perturbations, leading to localized failure features (e.g., cracks and compaction bands). These cnoidal waves, generally found in fluids, have strong nonlinearities that produce periodic patterns. Due to the singular nature of the solutions, the applicability of the theory is currently limited. Additionally, practical simulation tools require proper regularization to overcome the challenges that singularity induces. We focus on the numerical treatment of the governing equation using a nonlinear approach building on a recent adaptive stabilized finite element method. This automatic refinement method provides an error estimate that drives mesh adaptivity, a crucial feature for the problem at hand. We compare the performance of this adaptive strategy against analytical and standard finite element solutions. We then investigate the sensitivity of the diffusivity ratio, the parameter controlling the process, and identify multiple possible solutions with several stress peaks. We also show the evolution of the spacing between peaks for all solutions as a function of that parameter.

42 ENGINEERING↗

DOE OSTI2022

Discharge intermittency considerably changes ZnO spatial distribution in porous Zn anodes

Porous Zn anodes are ubiquitous in primary batteries and are under development for low-cost rechargeable batteries. Spatial distribution of ZnO discharge product is a critical factor in these, because it can passivate the active material. In rechargeable cells this is related to a major failure mechanism called shape change, in which ZnO is relocated to inactive locations. In this work we demonstrate rest steps during discharge of primary Zn anodes dramatically alter the placement of ZnO in the anode. In alkaline electrolyte, ZnO discharge product is typically modeled as precipitating close to Zn particles, forming a porous ZnO shell around the Zn core. Further, anodes discharged continuously at low-rate are compared to anodes similarly discharged intermittently, using in situ computed tomography from a synchrotron source. Zn–ZnO core-shell structures are produced during continuous discharge but are not found in cells discharged intermittently. Continuously discharged cells showed that ZnO was formed most strongly near the separator, in agreement with Zn anode battery models. In pulse-discharged cells, ZnO was more radially distributed and was in large formations not physically connected to Zn particles. Thus, discharge intermittency changes spatial distribution of ZnO in ways that are unpredicted by Zn anode models.

25 ENERGY STORAGE↗

DOE OSTI2020

Model-Instructed Design of Novel Charging Protocols for the Extreme Fast Charging of Lithium-Ion Batteries Without Lithium Plating

Relatively long recharge time of high-energy density lithium-ion batteries (LIBs) is one of the major obstacles to the widespread deployment of electric vehicles (EVs). Excessive fast charge of LIBs can cause severe safety issues, the most significant of which is lithium plating. In addition to the consumption of cyclable lithium, dendrite-like lithium plating can cause short-circuiting within the cell, which could lead to catastrophic failure. In addition to the developments of advanced electrolytes, active materials and electrodes, the fast charging capability of LIBs can be improved by using optimized charging protocol. In this paper, the Pseudo2D battery model is first used to screen some conventional charging protocols proposed for fast charging, including the constant-current constant-voltage charging (CCCV), constant-power constant-voltage charging (CPCV), multi-stage constant-current charging, and pulse current charging. A semi-optimal charging protocol is then developed by automatically modifying the charge current such that the cell is charged at close-to-maximum current without lithium plating. Based on the features of the semi-optimal protocol, two practical novel fast charging protocols are proposed which allow charging the cell at a higher rate without lithium plating. Through simulation, we show that the no-plating capacity after 10 min charge can be improved by up to ~10.7% compared to CCCV charging for a 2.5 mAh cm -2 cell and ~18.8% for a 4 mAh cm -2 cell, when the proposed charging protocols are used.

25 ENERGY STORAGE↗

DOE OSTI2020

Perspective—On the Need for Reliability and Safety Studies of Grid-Scale Aqueous Batteries

Li-ion batteries currently dominate electrochemical energy storage for grid-scale applications, but there are promising aqueous battery technologies on the path to commercial adoption. Though aqueous batteries are considered lower risk, they can still undergo problematic degradation processes. This perspective details the degradation that aqueous batteries can experience during normal and abusive operation, and how these processes can even lead to cascading failure. We outline methods for studying these phenomena at the material and single-cell level. Considering reliability and safety studies early in technology development will facilitate translation of emerging aqueous batteries from the lab to the field.

25 ENERGY STORAGE↗