Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Influence of Ar/Kr ratio and pulse parameters in a Cr-N high power pulse magnetron sputtering process on plasma and coating properties

Krypton is sometimes used in physical vapor deposition processes due to its greater atomic mass and size compared to argon, which leads to a lower gas incorporation and may have beneficial effects on kinetics of the coating growth. In this paper, the authors investigate the plasma composition and properties of deposited high power pulse magnetron sputtering Cr-N coatings for discharges with various Ar/Kr ratios and for various pulse lengths of 40 μs, 80 μs, and 200 μs, keeping the average discharge power constant. The results show that an addition of Kr influences the discharge process by altering the ignition and peak values of the discharge current. This influences the metal ion generation and growth conditions on the substrate by reducing the nucleation site densities, leading to a predominantly columnar grow. However, the deposition rate is highest for an Ar/Kr ratio of 120/80. The integral of the metal ion and atom emission exhibits the same trend, having a maximum for Ar/Kr ratio of 120/80. By decreasing the pulse length, the deposition rate of coatings decreases, while the hardness increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-temperature growth of gallium nitride films by inductively coupled-plasma-enhanced reactive magnetron sputtering

Gallium nitride (GaN) films were grown on sapphire substrate by reactive magnetron sputtering. Inductively coupled-plasma (ICP) source was installed between the substrate holder and the sputtering target to increase the plasma density and the degree of ionization of nitrogen gas. Liquid Ga and Ar/N{sub 2} were used as the sputtering target and sputtering gases, respectively. X-ray diffraction measurements confirmed that the authors could grow high quality GaN crystallites at 500 °C. However, the crystalline GaN (0002) peak remained even by lowering the growth temperature down to 300 °C. The N:Ga ratio of the film grown at 500 °C was almost 1:1, and the nitrogen composition became higher toward the 1:1 N:Ga ratio with increasing the growth temperature. The high degree of ionization induced by ICP source was essential to the growth of high crystalline quality GaN films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis of copper nitride films doped with Fe, Co, or Ni by reactive magnetron sputtering

Copper nitride (Cu{sub 3}N) and Fe-, Co-, and Ni-doped Cu{sub 3}N films were prepared by reactive magnetron sputtering. The films were deposited on silicon substrates at room temperature using pure Cu target and metal chips. The molar ratio of Cu to N atoms in the as-prepared Cu{sub 3}N film was 2.7:1, which is comparable with the stoichiometry ratio 3:1. X-ray diffraction measurements showed that the films were composed of Cu{sub 3}N crystallites with anti-ReO{sub 3} structure and adopted different preferred orientations. The reflectance of the four samples decreased in the wavelength range of 400–830 nm, but increased rapidly within wavelength range of 830–1200 nm. Compared with the Cu{sub 3}N films, the resistivity of the doped Cu{sub 3}N films decreased by three orders of magnitude. These changes have great application potential in optical and electrical devices based on Cu{sub 3}N films.

36 MATERIALS SCIENCE↗

Deposition of highly textured AlN thin films by reactive high power impulse magnetron sputtering

Aluminum nitride thin films were deposited by reactive high power impulse magnetron sputtering (HiPIMS) and pulsed direct-current on Si (100) and textured Mo substrates, where the same deposition conditions were used for both techniques. The films were characterized by x-ray diffraction and atomic force microscopy. The results show a pronounced improvement in the AlN crystalline texture for all films deposited by HiPIMS on Si. Already at room temperature, the HiPIMS films exhibited a strong preferred (002) orientation and at 400 °C, no contributions from other orientations were detected. Despite the low film thickness of only 200 nm, an ω-scan full width at half maximum value of 5.1° was achieved on Si. The results are attributed to the high ionization of sputtered material achieved in HiPIMS. On textured Mo, there was no significant difference between the deposition techniques.

42 ENGINEERING↗

Properties of Cu(In,Ga,Al)Se{sub 2} thin films fabricated by magnetron sputtering

Cu(In,Ga,Al)Se{sub 2} (CIGAS) thin films were studied as an alternative absorber layer material to Cu(In{sub x}Ga{sub 1−x})Se{sub 2}. CIGAS thin films with varying Al content were prepared by magnetron sputtering on Si(100) and soda-lime glass substrates at 350 °C, followed by postdeposition annealing at 520 °C for 5 h in vacuum. The film composition was measured by an electron probe microanalyzer while the elemental depth profiles were determined by secondary ion mass spectrometry. X-ray diffraction studies indicated that CIGAS films are single phase with chalcopyrite structure and that the (112) peak clearly shifts to higher 2θ values with increasing Al content. Scanning electron microscopy images revealed dense and well-defined grains, as well as sharp CIGAS/Si(100) interfaces for all films. Atomic force microscopy analysis indicated that the roughness of CIGAS films decreases with increasing Al content. The bandgap of CIGAS films was determined from the optical transmittance and reflectance spectra and was found to increase as Al content increased.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal conductivity of nitride films of Ti, Cr, and W deposited by reactive magnetron sputtering

Nitride films of Ti, Cr, and W were deposited using reactive magnetron sputtering from metal targets in argon and nitrogen plasma. TiN films with (200) orientation were achieved on silicon (100) at the substrate temperature of 500 and 600 °C. The films were polycrystalline at lower temperature. An amorphous interface layer was observed between the TiN film and Si wafer deposited at 600 °C. TiN film deposited at 600 °C showed the nitrogen to Ti ratio to be near unity, but films deposited at lower temperature were nitrogen deficient. CrN film with (200) orientation and good stoichiometry was achieved at 600 °C on Si(111) wafer but the film deposited at 500 °C showed cubic CrN and hexagonal Cr{sub 2}N phases with smaller grain size and amorphous back ground in the x-ray diffraction pattern. An amorphous interface layer was not observed in the cubic CrN film on Si(111) deposited at 600 °C. Nitride film of tungsten deposited at 600 °C on Si(100) wafer was nitrogen deficient, contained both cubic W{sub 2}N and hexagonal WN phases with smaller grain size. Nitride films of tungsten deposited at 500 °C were nonstoichiometric and contained cubic W{sub 2}N and unreacted W phases. There was no amorphous phase formed along the interface for the tungsten nitride film deposited at 600 °C on the Si wafer. Thermal conductivity and interface thermal conductance of all the nitride films of Ti, Cr, and W were determined by transient thermoreflectance technique. The thermal conductivity of the films as function of deposition temperature, microstructure, nitrogen stoichiometry and amorphous interaction layer at the interface was determined. Tungsten nitride film containing both cubic and hexagonal phases was found to exhibit much higher thermal conductivity and interface thermal conductance. The amorphous interface layer was found to reduce effective thermal conductivity of TiN and CrN films.

36 MATERIALS SCIENCE↗

Resputtering effect during MgO buffer layer deposition by magnetron sputtering for superconducting coated conductors

In this study, MgO thin films were deposited by radio-frequency magnetron sputtering. The film thickness in the deposition area directly facing the target center obviously decreased compared with that in other areas. This reduction in thickness could be attributed to the resputtering effect resulting from bombardment by energetic particles mainly comprising oxygen atoms and negative oxygen ions. The influences of deposition position and sputtering pressure on the deposition rate were investigated. Resputtering altered the orientation of the MgO film from (111) to (001) when the film was deposited on a single crystal yttria-stabilized zirconia substrate. The density distribution of energetic particles was calculated on the basis of the measured thicknesses of the MgO films deposited at different positions. The divergence angle of the energetic particle flux was estimated to be approximately 15°. The energetic particle flux might be similar to the assisting ion flux in the ion beam assisted deposition process and could affect the orientation of the MgO film growth.

36 MATERIALS SCIENCE↗

Development of high-vacuum planar magnetron sputtering using an advanced magnetic field geometry

A permanent magnet in a new magnetic field geometry (namely, with the magnetization in the radial direction) was fabricated and used for high-vacuum planar magnetron sputtering using Penning discharge. Because of the development of this magnet, the discharge current and deposition rate were increased two to three times in comparison with the values attainable with a magnet in the conventional geometry. This improvement was because the available space for effective discharge of the energetic electrons for the ionization increased because the magnetic field distribution increased in both the axial and radial directions of discharge.

42 ENGINEERING↗

Ti-Nb thin films deposited by magnetron sputtering on stainless steel

Thin films of Ti-Nb alloys were deposited on AISI 316L stainless steel substrate by magnetron sputtering, and the structure, composition, morphology, and microstructure of the films were analyzed by means of x-ray diffraction (XRD), (scanning) transmission electron microscopy (TEM) coupled with energy-dispersive x-ray spectroscopy, atomic force microscopy (AFM), and x-ray photoelectron spectroscopy (XPS). Thin films of four compositions were produced: Ti{sub 85}Nb{sub 15} (Ti-26 wt. % Nb), Ti{sub 80}Nb{sub 20} (Ti-33 wt. % Nb), Ti{sub 70}Nb{sub 30} (Ti-45 wt. % Nb), and Ti{sub 60}Nb{sub 40} (Ti-56 wt. % Nb). Structural characterization by XRD indicated that only the β phase was present in the thin films and that the increase in the Nb content modified the alloy film texture. These changes in the film texture, also detected by TEM analysis, were attributed to different growth modes related to the Nb content in the alloy films. The mean grain sizes measured by AFM increased with the Nb amount (from 197 to 222 nm). XPS analysis showed a predominance of oxidized Ti and Nb on the film surfaces and an enrichment of Ti.

36 MATERIALS SCIENCE↗

Synthesis and characterization of MoB{sub 2−x} thin films grown by nonreactive DC magnetron sputtering

DC magnetron sputtering was used to deposit molybdenum boride thin films for potential low-friction applications. The films exhibit a nanocomposite structure with ∼10 nm large MoB{sub 2−x} (x > 0.4) grains surrounded by a boron-rich tissue phase. The preferred formation of the metastable and substoichiometric hP3-MoB{sub 2} structure (AlB{sub 2}-type) is explained with kinetic constraints to form the thermodynamically stable hR18-MoB{sub 2} phase with a very complex crystal structure. Nanoindentation revealed a relatively high hardness of (29 ± 2) GPa, which is higher than bulk samples. The high hardness can be explained by a hardening effect associated with the nanocomposite microstructure where the surrounding tissue phase restricts dislocation movement. A tribological study confirmed a significant formation of a tribofilm consisting of molybdenum oxide and boron oxide, however, without any lubricating effects at room temperature.

36 MATERIALS SCIENCE↗

Characterizing the composition, structure, and mechanical properties of magnetron sputtering physical vapor deposition TiN and TiSiN coatings

Ti(Si)N coatings were deposited on Si wafers via magnetron sputtering physical vapor deposition technique. Scanning electron microscopy and atomic force microscopy were used to study the morphologies, grain size, and thicknesses of the different films. X-ray diffraction confirmed the formation of the titanium nitride cubic phase. X-ray photoelectron spectroscopy (XPS) was used to study the silicon and oxygen levels in the films, and high resolution XPS was used to determine the surface oxide to nitride ratios as well as the silicon–nitrogen environment. The hardness of these films was then determined with nanoindentation. It was shown that grain size and film density could be controlled by the Si level and the ion bombardment to eliminate the oxygen level in the nitride coatings, which led to the harder films. It was suggested that due to the miscibility of Si, a ternary TiSiN solid solution was formed. Stronger (200) orientation of the TiN B1-NaCl crystals was associated with increased hardness of the coatings. In conclusion, this crystalline structure was preserved after incorporating Si.

36 MATERIALS SCIENCE↗

Impact of high-power impulse magnetron sputtering pulse width on the nucleation, crystallization, microstructure, and ferroelectric properties of hafnium oxide thin films

The impact of the high-power impulse magnetron sputtering (HiPIMS) pulse width on the crystallization, microstructure, and ferroelectric properties of undoped HfO 2 films is investigated. HfO 2 films were sputtered from a hafnium metal target in an Ar/O 2 atmosphere, varying the instantaneous power density by changing the HiPIMS pulse width with fixed time-averaged power and pulse frequency. The pulse width is shown to affect the ion-to-neutral ratio in the depositing species with the shortest pulse durations leading to the highest ion fraction. In situ x-ray diffraction measurements during crystallization demonstrate that the HiPIMS pulse width impacts nucleation and phase formation, with an intermediate pulse width of 110 μ s stabilizing the ferroelectric phase over the widest temperature range. Although the pulse width impacts the grain size with the lowest pulse width resulting in the largest grain size, the grain size does not strongly correlate with the phase content or ferroelectric behavior in these films. In conclusion, these results suggest that precise control over the energetics of the depositing species may be beneficial for forming the ferroelectric phase in this material.

36 MATERIALS SCIENCE↗

Deposition of copper coatings in a magnetron with liquid target

Copper coatings were deposited on monocrystalline Si substrates using a magnetron discharge with a liquid cathode in the metal vapour plasma. During the deposition, the bias voltage in the range from 0 V to–400 V was applied to the substrate. The prepared films were investigated by a scanning electron microscope, and their adhesive properties were studied using a scratch tester. It was demonstrated that the adhesion of the deposited films strongly depends on the bias voltage and varies in a wide range.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characteristics of the magnetron discharge plasma at large distances from the cathode

The parameters of the magnetron plasma at distances several times larger than the cathode diameter were measured. The plasma temperature and density measured by the probe technique were found to be 1.4 eV and 6 x 10{sup 10} cm{sup -3}, respectively. The dependences of the plasma density and temperature on the argon flow rate in the course of TiAlN coating deposition were determined. Before deposition of the coating, the substrate was cleaned by ion sputtering at substrate bias voltages higher than 200 V.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Nonsputtering impulse magnetron discharge

Experiments with quasi-steady high-current discharges in crossed E Multiplication-Sign B fields in various gases (Ar, N{sub 2}, H{sub 2}, and SF{sub 6}) and gas mixtures (Ar/SF{sub 6} and Ar/O{sub 2}) at pressures from 10{sup -3} to 5 Torr in discharge systems with different configurations of electric and magnetic fields revealed a specific type of stable low-voltage discharge that does not transform into an arc. This type of discharge came to be known as a high-current diffuse discharge and, later, a nonsputtering impulse magnetron discharge. This paper presents results from experimental studies of the plasma parameters (the electron temperature, the plasma density, and the temperature of ions and atoms of the plasma-forming gas) of a high-current low-pressure diffuse discharge in crossed E Multiplication-Sign B fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Properties of GaAsN nanowires grown by magnetron-sputtering deposition

The effectiveness of magnetron-sputtering deposition in an Ar-N{sub 2} plasma-forming mixture as a technique for the fabrication of arrays of GaAs{sub 1-x}N{sub x} nanowires (NWs) with typical diameters from 10 to 200 nm and lengths up to 3000 nm is demonstrated. Dependence of the growth character of NW on the parameters of the synthesis process, such as the size of Au droplets, deposition rate, and crystallographic orientation of the surface and the temperature of the substrate, is investigated. Analysis of the dependence of NW height on their diameter demonstrates that growth occurs predominantly by the diffusion mechanism. The nitrogen content is kept stable for growth temperatures in the range 400-500{sup o}C, being as high as 2.7%. For the substrate temperatures in the range 530-600{sup o}C, an abrupt drop in the nitrogen content in the alloy takes place. In the photoluminescence (PL) spectra of the samples obtained, a red shift of the emission band is observed, which is related to an increase in the nitrogen content. The growth-temperature dependence of the position of the luminescence band and the nitrogen content is determined. It is found that the PL intensity of samples with GaAsN NWs containing 2.7% nitrogen increases by a factor of 5-10 as compared to samples with planar layers, which is explained by the absence of structural defects in NWs.

39↗

Comprehensive study of the conditions for obtaining hydrogenated amorphous erbium- and oxygen-doped silicon suboxide films, a-SiO{sub x}:H Left-Pointing-Angle-Bracket Er,O Right-Pointing-Angle-Bracket , by dc-magnetron deposition

The results of a comprehensive study of the conditions for growing a-SiO{sub x}:H Left-Pointing-Angle-Bracket Er,O Right-Pointing-Angle-Bracket films are presented. The effect of the composition of various erbium-containing targets (a-SiO{sub x}:H , ErO{sub x}, Er{sub 2}SiO{sub 5}, Er{sub 2}O{sub 3}, and Er), substrate temperature, and annealing temperatures in argon, air, and under conditions of SiH{sub 4} + Ar + O{sub 2} plasma glow is studied. In order to obtain a-SiO{sub x}:H Left-Pointing-Angle-Bracket Er,O Right-Pointing-Angle-Bracket films with the highest photoluminescence intensity of erbium ions, it is recommended for the following technological conditions to be used: the substrate holder should be insulated from dc-magnetron electrodes and the working gas mixture should include silane, argon, and oxygen. Single-crystal silicon and metal erbium should be used as targets. The erbium target should be placed only in the Si-target erosion zone.

36 MATERIALS SCIENCE↗

Different properties of aluminum doped zinc oxide nanostructured thin films prepared by radio frequency magnetron sputtering

Aluminium doped zinc oxide (AZO) nanostructured thin films are prepared by radio frequency magnetron sputtering on glass substrate using specifically designed ZnO target containing different amount of Al{sub 2}O{sub 3} powder as the Al doping source. The optical properties of the aluminium doped zinc oxide films are investigated. The topography of the deposited films were investigated by Atomic Force Microscopy. Variation of the refractive index by annealing temperature are considered and it is seen that the refractive index increases by increasing the annealing temperature.

36 MATERIALS SCIENCE↗