SEARCH · Engineering Papers

Results for “Irradiance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Irradiation and PIE of alloys X-750 and XM-19 (EPRI Phase III)

The Nuclear Science User Facilities (NSUF) based at Idaho National Laboratory (INL), along with the Electric Power Research Institute (EPRI), formed an agreement to test representative alloys used as reactor structural materials as a pilot program to establish guidelines for future NSUF research programs. This report contains results from the portion of this program established as Phase III (of three phases), entailing irradiation and post-irradiation examination of select alloys typical of boiling water reactor (BWR) internal structural materials. Phases I and II are the subject of separate reports and represent baseline material test results and irradiation experiment design, respectively. The intent of this Phase III research program is to determine properties for the materials of interest after being irradiated at the Advanced Test Reactor (ATR) to three different target fast (E>1MeV) fluences: 5.0 x 10¹⁹ n/cm², 2.0 x 10²⁰ n/cm², and 1.0 x 10²¹ n/cm². These correspond to irradiation damage levels (displacements per atom [dpa]) of approximately 0.08, 0.30, and 1.4 dpa, which represent comparable levels to (a) a previous study which looked at X-750 irradiated to ~1 x 10¹⁹ n/cm², comparable to the lowest fluence; (b) approximately a medium level of fluence for BWR components; and (c) extended life (60 – 80 years) for BWR components. The materials chosen for this research are the nickel-based alloy X-750 and austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co., and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research Center (GE-GRC), and parts were provided to INL for use in this pilot project.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

Irradiation and PIE of alloys X-750 and XM-19 (EPRI Phase III)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

High Temperature Steam Oxidation of Irradiated FeCrAl in the Severe Accident Test Station

FeCrAl-UO2 test capsules were fabricated at Oak Ridge National Laboratory (ORNL) and irradiated at the Advanced Test Reactor. Following irradiation, samples were sectioned from the irradiated rod and oxidation kinetics were evaluated to access the candidate cladding high-temperature oxidation performance following irradiation. The irradiation was performed at approximately 400°C to a burnup of 10 GWd/MT. The high-temperature oxidation tests were conducted in the ORNL Severe Accident Test Station at 1200 and 1300°C. Weight measurements were taken before and after oxidation testing. Cross-sections of the cladding were metallographically mounted and optical microscopy was performed. Measurements of the oxidation layer before and after high-temperature testing were collected. The results indicate the irradiated FeCrAl C35M alloy provided good thermal stability up to 1200°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Effects of Irradiation on Thermal Properties of Polyurethane Foam

Polyurethane foam is used as a thermal insulator, fire protective material, and impact absorber in the 9977 shipping package. The 9977 shipping package is used to transport special nuclear materials (SNM), and store SNM in the K-area complex at the Savannah River Site. The primary fire-retardant mechanism in the foam is that it produces intumescent char when exposed to high temperatures. Intumescence occurs in the direction of heat application and can allow the foam to “repair” cracks in the event of a mechanical impact, in addition to serving as a secondary thermal barrier with decreased heat conductivity. Because the foam is being used for long-term storage applications, it is vital that it retain its physical, thermal, and mechanical properties over the course of time and with the events of exposure of heat and irradiation. The goal of this project was to determine the effects of gamma irradiation on the thermal properties of polyurethane foam, both in terms of cumulative irradiation and rate of irradiation. At the dose rates and cumulative doses of irradiation measured, there was no correlation between higher cumulative irradiation and thermal stability, specific heat capacity, or chemical structure. Based on the results of the experiments, the fire protective properties in the 9977 shipping containers should be retained with the expected amount of radiation exposure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A Procedure to Correct the Historical Atmospheric Longwave Irradiance Data When the World Reference Is Established with Respect to the International System of Units

Historical atmospheric longwave irradiance data sets with traceability to the International System of Units (SI) are essential for renewable energy and atmospheric science research and applications. To date, all pyrgeometers used to measure the irradiance are traceable to the interim World Infrared Standard Group (WISG), not to SI units. In 2013, the Absolute Cavity Pyrgeometer (ACP) (Reda et al. 2012) was developed at the National Renewable Energy Laboratory (NREL) to measure the atmospheric longwave irradiance. The ACP has been compared against the InfraRed Integrating Sphere (IRIS), developed by the Physikalisch-Meteorologisches Observatorium Davos/World Radiation Center (PMOD/WRC) (Gröbner 2012). The ACP and the IRIS are absolute instruments traceable to SI units through the International Temperature Scale of 1990. Results of six comparisons between the ACP and the IRIS at different locations have shown that the irradiance measured by WISG pyrgeometers underestimates clear-sky atmospheric longwave irradiance by 2 W/m 2 to 6 W/m 2 (Gröbner et al. 2014); therefore, once the world reference is established with traceability to SI units, the WISG would be corrected, then used to calibrate field pyrgeometers with traceability to SI units. The following described method is used to correct the historical atmospheric longwave irradiance data sets in anticipation of the WISG scale change.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Effects of Electron Irradiation on Candidate Materials for Target Window in Accelerator-Driven Mo-99 Production

Room-temperature (RT) axial tensile tests were conducted in 2018 and 2021 with flat, sub-sized, dog-boned samples of non-irradiated and irradiated Inconel 718 and irradiated beryllium (Be). The sample gauge length was 7.62 mm. Tensile properties of interest are the engineering yield stress (YS), ultimate tensile stress (UTS), uniform elongation (UE) and total elongation (TE). The electron dose of the 2021 samples was ≈2 times the dose of samples tested in 2018. Relative dose rates of 0, 1 (2018), and 2 (2021) are assigned to these samples. The 2021 electron-irradiated Be samples were brittle with a low failure stress of 338±64 MPa based on two samples. The failures occurred in the gauge section. The 2018 results for electron-irradiated Be indicated a slight decrease in ductility and strength for the one electron-irradiated sample that failed in the gauge section.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2022

Irradiation of MiniFuel Targets Bearing TRISO Fuel Compacts (Status Report)

Irradiation testing of MiniFuel compacts bearing tristructural isotropic (TRISO) fuel particles was performed at Oak Ridge National Laboratory (ORNL) to support the development of Kairos Power’s (KP’s) fluoride salt–cooled high-temperature reactor concept. The fuel compacts were fabricated with TRISO fuel particles of different types—including low-enriched uranium oxide, uranium carbide (LEUCO), natural uranium oxide, uranium carbide (NUCO), and low-enriched uranium dioxide (LEUO 2 )—and inserted into MiniFuel irradiation targets. Five targets were assembled and inserted in the High Flux Isotope Reactor (HFIR) for four cycles. The data collected post-irradiation will provide experimental input to validate TRISO fuel performance models for high particle power operations. This report summarizes the completion of the HFIR irradiation, the as-irradiated numerical analysis, and the post-irradiation work performed to date. This work was performed under the Nuclear Science User Facility program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Uncertainty in Annual Energy Resulting from Uncertain Irradiance Measurements

We report an analysis quantifying the contribution to uncertainty in annual energy projections from uncertainty in ground-measured irradiance. Uncertainty in measured irradiance is quantified for eight instruments by the difference from a well maintained, secondary standard pyranometer which is regarded as truthful. We construct a statistical model of irradiance uncertainty and apply the model to generate a sample of 100 annual time series of irradiance for each instrument. The sample is propagated through a common performance model for a reference photovoltaic system to quantify variation in annual energy. Although the measured irradiance varies from the reference by a few percent (standard deviation of 1-2%) the uncertainty in annual energy is on the order of a fraction of one percent. We propose a model for a factor that represents uncertainty in modeled annual energy that arises from uncertainty in ground-measured irradiance.

14 SOLAR ENERGY↗

DOE OSTI2022

Report on Evolution of Inconel 718 Following HFIR Irradiation

The report presents the microstructure and mechanical properties of 3D printed Inconel 718 after irradiation in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) to assess its potential use as a structural material. The structural components near the outlets of several proposed reactor cores will experience significant neutron fluxes and outlet coolant temperatures ranging from the hot standby temperature of 300 °C to nearly 550 °C at the center of the part. These components must support the core in appropriate loading conditions and require structural analysis at relevant temperatures. In FY21, three heat treatments were designed and conducted to simplify the microstructure and to determine how each precipitating phase contributed to the overall strength. In FY21, baseline mechanical properties were measured from uniaxial tensile tests on subsize SS-J2 specimens at room temperature and at elevated temperatures of 300, 450, and 600 °C to serve a comparison to the irradiated properties. Four capsules containing 3D printed Inconel 718 were inserted into HFIR in FY21 for a matrix of two temperatures and two doses. The lower of the two doses was available for characterization in FY22. Multiple heat treatments of Inconel 718 irradiated to nominal conditions of 2 displacements per atom (dpa) at either 300 or 600 °C were strained with uniaxial tensile tests at the Irradiated Material Examination and Testing (IMET) Facility to discern the mechanical properties. Transmission electron microscopy was performed to correlate the observed mechanical properties with nanoscale features. The initially homogenous AM718-HM increased in strength at both irradiation temperatures based on a high density of nanometer-scale radiation-induced cavities at lower temperature and nucleation and growth of γ" precipitates at higher temperatures. The precipitate-hardened AM718-HT2 showed very small differences in strength before and after irradiation: the contribution to strength from γ" precipitates was replaced with dislocation loops. Because the radioactivity of the nickel superalloys from neutron activation limited the scope of the analysis, a feasibility study examined the possibility of an ultra-miniature specimen geometry, colloquially SS-Tiny (SS-T), for mechanical property determination using the nonirradiated Inconel 718. This study found an overestimation of ductility from the SS-T geometry with yield strength and ultimate tensile strength slightly above the SS-J2 geometry: this could be contributed to a reduction in specimen thickness.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Implementation of Distributed Memory Computing in MOSAIC to Enable Large 3D Simulations of Irradiated Concrete

The concrete biological shield (CBS) of light-water reactors protects workers and the surrounding environment by absorbing neutron and gamma irradiation emitted from the reactor core. The radiation dose increases with the CBS’s operational time and, in the long term, becomes significant enough to raise the question of irradiation effects on concrete—and particularly on the structural integrity of the CBS. Irradiation-induced damage has been identified as one of the main degradation mechanisms in the CBS. Neutron radiation causes the swelling of aggregate-forming minerals at different rates and amplitudes depending on the mineral’s nature. Silicate-bearing minerals such as quartz are particularly sensitive to neutron radiation and experience up to 17.8% volumetric expansion. Aggregates comprise several minerals with different orientations and are, therefore, subject to cracking as a result of mismatch strains. Additionally, the swelling of aggregates creates significant stresses in the surrounding cement paste matrix, which also results in crack formation. In parallel with the collection of characterization and irradiation test data, development of modeling and simulation tools for irradiated concrete is ongoing with the support of the US Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) program. This effort resulted in the development and application of the fast-Fourier transform (FFT)–based code Microstructure-Oriented Scientific Analysis of Irradiated Concrete (MOSAIC) at Oak Ridge National Laboratory.

61 RADIATION PROTECTION AND DOSIMETRY↗

DOE OSTI2022

Preparation & shipping of ten neutron irradiated Eurofer97 steel variants to HFIR for SANS experiments

At ORNL, ten variants of Eurofer97 steel were irradiated in the high flux isotope reactor (HFIR) to ~2.94 – 3.24 dpa at 300 ± 30 °C, as part of the EUROfusion Lot-IV collaboration. The irradiations were performed in non-instrumented rabbit capsules in the flux trap region, which included SS-J3 type tensile samples and M4-CVN multi-notch bend bars. Their full set of microstructure and mechanical properties were previously reported in multiple previous publications. In this project, half-broken irradiated and nonirradiated SS-J3 tensile samples from ten alloys, code-named H, I, J, K, L, M, N, O, P and E, were prepared and shipped for facilitating small angle neutron scattering (SANS) experiments at the HFIR general purpose (GP)-SANS beam line. This report summarizes the completed tasks which included canister moves at the Irradiated Materials Examination and Testing (IMET) hot-cell facility to retrieve the samples from long-term storage, loading of the ten irradiated samples at IMET inside lead (Pb) piglets that were specifically provided by ORNL for SANS experiments and radiological shipment from IMET facility to the HFIR hot cells for performing SANS experiments. In addition to the irradiated samples, ten nonirradiated half-broken pieces from the Eurofer97 variants were also provided to HFIR for SANS.

36 MATERIALS SCIENCE↗

DOE OSTI2023

UCO TRISO Minifuel FY23 NSUF-Kairos Power Post-Irradiation Examination Status Report

Irradiation of miniature tristructural isotropic (TRISO)–coated particle fuel compacts at high-power particle was performed in the Oak Ridge National Laboratory’s (ORNL’s) High Flux Isotope Reactor (HFIR) using the MiniFuel irradiation capability. Each compact comprised 20 TRISO particles with a low-enriched uranium carbide uranium oxide (UCO), natural UCO, or low-enriched UO 2 kernel within a graphitic matrix. After irradiation, the MiniFuel targets and subcapsules were disassembled to recover the irradiated fuel specimens and pursue post-irradiation examination (PIE) to inform Kairos Power on the fuel specimen performance. This report describes the PIE results collected to date, including dilatometry on the passive thermometry to confirm the irradiation temperature, fission gas release measurements, and gamma counting. This work was funded by the Nuclear Science User Facilities program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Neutron Dosimetry for the GE Hitachi 16-10393 Irradiation in ATR

PNNL project 74242 involves the analysis of neutron fluence monitors and melt wires irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory in accordance with MPO 00236287 and Statement of Work (SOW) No. 17370, Rev. 0, PNNL Analysis of NSUF Flux and Melt Wire Capsules. This report is for the GE Hitachi 16-10393 irradiation which was conducted in positions B11 of the ATR. Three other irradiations included in the SOW will be reported separately. The neutron fluence monitors were prepared by PNNL and loaded into the GE Hitachi assemblies prior to irradiation. Following irradiation, the capsules were returned to PNNL for analysis. The neutron dosimetry capsules were opened, the flux wires were removed for gamma analysis. The measured activities were used to determine the activation rates for various activation products. Following suitable corrections, the measured activation rates were used to adjust calculated neutron spectra at each fluence monitor location. The adjusted neutron spectra were then used to determine displacement per atom (dpa) and gas production for irradiated materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Computer vision models and advanced TEM imaging for microstructures of irradiated AM316 stainless steels

Advancements were made in automating microscopy-based material characterization, particularly in studying irradiation effects on additively manufactured (AM) materials using machine learning (ML) and computer vision (CV). These automation efforts address the challenges of analyzing complex microstructures, accelerating the detection of irradiation-induced defects. Two CV models were developed at Argonne National Laboratory (ANL) to enhance transmission electron microscopy (TEM) analysis of irradiated AM 316 stainless steel. The first model focused on the detection of irradiation-induced dislocation loops, which contribute to material hardening and embrittlement. These loops, categorized as faulted or perfect, were automatically detected and classified using a Mask R-CNN model trained on TEM images from both in-situ and ex-situ ion irradiation experiments. The model achieved high accuracy, with precision, recall, and F1 scores of 0.839, 0.734, and 0.776, respectively, demonstrating its effectiveness in analyzing dislocation loops in irradiated AM materials. The second CV model was developed to analyze the size and wall thickness of dislocation cells in laser powder bed fusion (LPBF) 316 stainless steel. Using a U-Net++ architecture with EfficientNet as the encoder, the model was trained on TEM images to segment and measure cell size and wall thickness.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Accelerated Irradiation and Qualification of Ceramic Nuclear Fuels

Accelerated neutron irradiation testing is an component of accelerated qualification of new nuclear fuels for light water reactor (LWRs), microreactors, and other special purpose reactors. The qualification and licensing of nuclear fuel is a lengthy process that can take 20-25 years to bring a new fuel into service. Accelerated fuel qualification combines both experimental and modeling work to expedite the total qualification time to 5-10 years timeframe. The experimental aspect of this is accelerated irradiation aims to reduce the total time needed for neutron irradiation to achieve targeted burnup, which can take years using conventional irradiation profiles. The data that results from this irradiation testing can then be entered into BISON models to develop robust and reliable performance simulations to ensure safe operation under normal and off normal conditions. This milestone focused on the fabrication of test articles for accelerated irradiation testing at the Advance Test Reactor (ATR).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Post-irradiation Examination Status for the BSU-269 Project

High-density uranium inter-metallic uranium silicide (U 3 Si 2 ) was initially considered as a potential advanced nuclear fuel for light water reactor (LWR) systems due to several advantages it demonstrated in thermophysical properties, chemical, and irradiation stability. In addition to understanding the basic thermophysical and mechanical properties of U 3 Si 2 under LWR irradiation conditions, it is important to assess its performance with advanced claddings such as FeCrAl, SiC, or conventional Zr-based claddings. Several aspects of the fuel cycle and fuel performance are being evaluated for U 3 Si 2 coupled with different types of claddings. To thoroughly characterize the U 3 Si 2 -cladding system, their chemical compatibilities and the potential for fuel-cladding chemical interaction (FCCI) must be addressed. Interdiffusion studies have been performed between U 3 Si 2 /Zry-4 and U 3 Si 2 /FeCrAl using diffusion couples. For the U 3 Si 2 /Zry-4 system, ZrSi 2 was the primary interdiffusion product observed at 800°C in addition to other secondary phases from the Zr alloying elements such as Fe and Cr. Low melting point U 6 Fe was also observed at 1000°C. For the U 3 Si 2 /FeCrAl system, at temperatures above 500°C, chemical diffusion Fe-U and Fe-U-Si was observed, increasing with rising temperatures. Although information from these non-irradiated tests is a fundamental first assessment, follow-up with focused irradiation tests is necessary. Irradiation can significantly alter the structure and evolution of the FCCI layers compared to the non-irradiated conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Neutron Dosimetry for the Boise State University JW 15-8242 Irradiation in ATR (Rev.1)

PNNL project 79550 provides for the analysis of neutron fluence monitors irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory in accordance with MPO 00269673and Statement of Work No. 19704, Rev. 0, PNNL Analysis of NSUF Flux Capsules. This report is for the Boise State University (BSU) JW 15-8242 irradiations which were conducted in positions A6, A7 and A8 of the ATR. We previously reported data for this experiment after about 1 dpa in a report issued in January 2021 (1). This report is for longer irradiations to about 3 dpa. Other experiments included in the statement of work for this project will be reported separately. The neutron fluence monitors were prepared by PNNL and loaded into the BSU assemblies prior to irradiation. Following irradiation, the capsules were returned to PNNL for analysis. The neutron dosimetry capsules were opened, the flux wires were removed for gamma or x-ray analysis, and the measured activities were used to determine the activation rates for various activation products. Following suitable corrections, the measured activation rates were used to adjust calculated neutron spectra at each fluence monitor location. The adjusted neutron spectra were then used to determine displacement per atom (dpa) and gas production for irradiated materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Impacts of Irradiation Structural Behavior on Thermal Hydraulics Safety Analysis to Support MURR LEU Conversion

The University of Missouri Research Reactor (MURR) located in Columbia, Missouri is one of six U.S. High Performance Research Reactors (USHPRR), including one critical facility, that is actively collaborating with U. S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Office of Reactor Conversion and Uranium Supply to convert from the use of highly enriched uranium (HEU; ≥20 wt% U-235) to low-enriched uranium (LEU; <20 wt% U-235) fuel. A new type of very high-density LEU fuel based on an alloy of uranium and 10 wt% molybdenum (U-10Mo) is expected to allow the conversion to LEU of MURR, as well as four other USHPRR. MURR has been working with the Reactor Conversion Pillar at Argonne to perform fuel element design and fuel cycle performance analyses, steady-state thermal hydraulics safety analysis, and accident safety analyses in preparation for the conversion of MURR and to support a preliminary safety analysis report for conversion to LEU fuels. Subsequent analyses have also been performed, including transition cycles where all-fresh LEU fuel elements are introduced upon conversion and progressing through reactor operations the core is brought to equilibrium. Thermal hydraulics safety analyses performed as part of the above have employed an assumption on channel gap reduction due to burnup-related phenomena including fuel swelling, irradiation creep, and oxide layer buildup. Recently, a series of structural analyses have been performed on the MURR LEU fuel plates and an element due to significant differences between the plate and element designs of the MURR HEU and LEU fuels. In addition, NUREG-1537 indicates that structural phenomena are to be evaluated. Two separate types of structural analyses were performed for the MURR LEU fuel element: fluid-structure interaction (FSI) and irradiation thermo-mechanical. The FSI analysis evaluated the effects of hydraulic forces on the MURR LEU fuel element to quantify the flow-induced plate deflection, and a minimal impact to the channel gap thickness was predicted under prototypic and bounding conditions. The irradiation thermo-mechanical analysis evaluated the effects of fuel swelling, irradiation creep, and thermal expansion for the MURR LEU plates and the element for prototypic thermal and irradiation conditions based on a high-fidelity approach multiphysics approach. Overall, this thermo-mechanical analysis predicts smaller gap thickness changes in previously limiting regions. Larger changes are predicted in the middle of channels, and for end channels where power density is not typically a maximum. An additional thermo-mechanical analysis was performed for the outermost HEU fuel plate, which showed a similar magnitude of deflection as the outermost LEU plate. Due to substantial differences between the channel gap reductions assumed for the previous safety analyses and those predicted by the irradiation thermo-mechanical analysis, a need to evaluate their impact on the thermal hydraulics safety analyses arose. This report presents the results from the steady-state safety analyses for normal operation as well as the accident analyses for the two most limiting accident scenarios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗