Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Bilayer Anion-Exchange Membrane with Low Borohydride Crossover and Improved Fuel Efficiency for Direct Borohdyride Fuel Cell

The development of membranes with low fuel crossover and high fuel efficiency is a key issue in direct borohydride fuel cells (DBFCs). In previous work, we produced a poly(vinyl alcohol) (PVA)-anion-exchange resin (AER) membrane with a low fuel crossover and a low fuel efficiency by introducing Co ions. In this work, a bilayer membrane was designed to improve the fuel efficiency and cell performance. The bilayer membrane was prepared by casting a PVA-AER wet gel onto the partially desiccated Co-PVA-AER gel. The bilayer membrane showed a borohydride permeability of 1.34 × 10 –6 cm 2 ·s –1 , which was even lower than that of the Co-PVA-AER membrane (1.98 ×10 –6 cm 2 ·s –1 ) and the PVA-AER membrane (2.80 × 10 –6 cm 2 ·s –1 ). The DBFC using the bilayer membrane exhibited a higher fuel efficiency (37.4%) and output power (1.73 Wh) than the DBFCs using the Co-PVA-AER membrane (33.3%, 1.27 Wh) and the PVA-AER membrane (34.3%, 1.2 Wh). Furthermore, the DBFC using the bilayer membrane achieved a peak power density of 327 mW·cm –2 , which was 2.14 times of that of the DBFC using the PVA-AER membrane (153 mW·cm –2 ). Finally, the drastic improvement benefited from the bilayer design, which introduced an interphase to suppress fuel crossover and avoided unnecessary borohydride hydrolysis.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Welding Process Development for Spent Nuclear Fuel Canister Repair

The potential for stress corrosion cracking (SCC) of welded stainless-steel interim storage containers for spent nuclear fuel (SNF) has been identified as a high priority data gap. This paper presents a fusion welding process that was developed for SNF canister repair. Submerged arc welding (SAW) was developed to weld 12.7 mm (0.5 in.) thick 304L stainless steel plates to simulate the initial welds on SNF canisters. The SAW procedure was qualified following ASME Boiler and Pressure Vessel Code requirements. During SAW, the welding temperature was recorded at various locations by using thermocouples. After SAW, weld microstructures were characterized, joint mechanical properties were tested, and the maximum tensile residual stress direction was identified. After SAW procedure qualification, artificial cracks were excavated perpendicular to the maximum tensile residual stress direction in the SAW heat affected zone. Machine cold-wire gas tungsten arc welding (CW-GTAW) was developed and used for repair welding at cracked locations.

Tang, Wei↗
NASA NTRS1993

US/CIS integrated NTRE

The paper describes the Nuclear Thermal Energy (NTRE) engine, developed by taking advantage of mature fuel technology developed in the former Soviet Union, thus shortening the development schedule of this engine for moon and Mars explorations. The near-term NTRE engine has a number of features that provide safety, mission performance, cost, and risk benefits. These include: (1) high-temperature long-life CIS fuel, (2) high-pressure recuperated expander cycle, (3) assured restart, (4) long-life cooled nozzle with thin inner wall, (5) long-life turbopumps, (6) heat radiation and electrical power generation, and (7) component integration synergy. Diagrams of the reactor core, the recuperated bottoming cycle flow schematic, and the recuperated bottoming cycle engine schematic are presented.

Bulman, M. J.↗
DOE OSTI2018

DEVELOPMENT OF A NUCLEAR FUEL SAFEGUARDS VERIFICATION TECHNOLOGY FOR NEW FACILITY TYPES: Use of fast neutron emission tomography for spent fuel verification

With the buildup of spent fuel inventories around the world from decommissioning activities, a tool for the efficient and effective verification of a variety of fuel types for long-term disposition is needed. Fast neutron emission tomography is a promising imaging technology that can address this problem and has been under development at Oak Ridge National Laboratory for the past two years. The goal of this capability is to detect the removal or substitution of individual fuel pins in spent nuclear fuel assemblies for international safeguards applications. The present imaging technique is based on neutron emissions originating primarily from curium-244, which is produced predominantly at the end of the exposure cycle. As a result, this technique may be sensitive not only to fuel pins that are removed or substituted subsequent to all irradiation, but also to fuel pins that are substituted and subsequently irradiated. At present, a laboratory prototype imager is under construction. The purpose of the prototype is to demonstrate an imaging capabilitysufficient to resolve individual fuel pins using commercially available boron straw detectors that can withstand the high gamma ray dose from a typical spent fuel assembly. To achieve both practical measurement durations and sufficient resolution to discern individual pins, the prototype imager employs a novel collimator design where the slits of a parallel-slit collimator are rearranged to distribute them around a ring surrounding the target fuel assembly. This paper will report on simulations and experimental results undertaken to converge on a final design, image reconstruction of sample fuel types of interest, and challenges associated.

Iyengar, Anagha↗
NASA NTRS2002

Fuel Cell Research at NASA GRC

An overview of NASA GRC (Glenn Research Center) initiatives and challenges in fuel cell technology. The research and development of fuel cells and regenerative fuel cell systems for a wide variety of applications, including earth-based and planetary aircraft, spacecraft, planetary surface power, and terrestrial use are discussed.

Perez-Davis, Marla E.↗
NASA NTRS2003

Proton Exchange Membrane (PEM) Fuel Cell Status and Remaining Challenges for Manned Space-Flight Applications

The Fuel Cell has been used for manned space flight since the Gemini program. Its power output and water production capability over long durations for the mass and volume are critical for manned space-flight requirements. The alkaline fuel cell used on the Shuttle, while very reliable and capable for it s application, has operational sensitivities, limited life, and an expensive recycle cost. The PEM fuel cell offers many potential improvements in those areas. NASA Glenn Research Center is currently leading a PEM fuel cell development and test program intended to move the technology closer to the point required for manned space-flight consideration. This paper will address the advantages of PEM fuel cell technology and its potential for future space flight as compared to existing alkaline fuel cells. It will also cover the technical hurdles that must be overcome. In addition, a description of the NASA PEM fuel cell development program will be presented, and the current status of this effort discussed. The effort is a combination of stack and ancillary component hardware development, culminating in breadboard and engineering model unit assembly and test. Finally, a detailed roadmap for proceeding fiom engineering model hardware to qualification and flight hardware will be proposed. Innovative test engineering and potential payload manifesting may be required to actually validate/certify a PEM fuel cell for manned space flight.

Reaves, Will F.↗
DOE OSTI2021

The U.S. Accident Tolerant Fuels Program — Update on a National Initiative

In 2012 the U.S. Congress directed the Department of Energy’s (DOE) Office of Nuclear Energy to give priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools. DOE developed a plan with a goal to insert a Lead Test Assembly (LTA) into a commercial light water reactor by the end of FY 2022. Three of the leading commercial nuclear fuel vendors, in concert with several participating commercial nuclear utilities, are now seriously engaged in this initiative and have exceeded initial expectations by having met DOE’s goal this year, three years ahead of schedule. The early successes of the ATF program are due in part to a strong collaboration by the DOE national laboratories with both commercial nuclear fuel vendors and the U.S. Nuclear Regulatory Commission. This undertaking has recently been expanded to incorporate an effort to extend burnup from the current U.S. regulatory limit of 62 GWD/MTU and increase enrichment as necessary to support routine utilization of fuel at >75 GWD/MTU. This effort provides a critical economic incentive to accelerate the deployment of ATF technologies. This paper reviews the DOE-sponsored, industry-led ATF concepts currently under development and highlights the contributions made by the DOE laboratories in support of these ATF concepts, including: 1) steady-state irradiation testing in the Advanced Test Reactor (ATR) and High Flux Isotope Reactor (HFIR); 2) transient irradiation testing in the Transient Reactor Test Facility (TREAT); 3) fabrication process development and characterization of high density fuels, Cr-coated Zry cladding, FeCrAl cladding, and SiC cladding; and 4) post-irradiation examination of lead test rods irradiated in commercial reactors.

Goldner, Frank J.↗
NASA NTRS2004

New High-Temperature Membranes Developed for Proton Exchange Membrane Fuel Cells

Fuel cells are receiving a considerable amount of attention for potential use in a variety of areas, including the automotive industry, commercial power generation, and personal electronics. Research at the NASA Glenn Research Center has focused on the development of fuel cells for use in aerospace power systems for aircraft, unmanned air vehicles, and space transportation systems. These applications require fuel cells with higher power densities and better durability than what is required for nonaerospace uses. In addition, membrane cost is a concern for any fuel cell application. The most widely used membrane materials for proton exchange membrane (PEM) fuel cells are based on sulfonated perfluorinated polyethers, typically Nafion 117, Flemion, or Aciplex. However, these polymers are costly and do not function well at temperatures above 80 C. At higher temperatures, conventional membrane materials dry out and lose their ability to conduct protons, essential for the operation of the fuel cell. Increasing the operating temperature of PEM fuel cells from 80 to 120 C would significantly increase their power densities and enhance their durability by reducing the susceptibility of the electrode catalysts to carbon monoxide poisoning. Glenn's Polymers Branch has focused on developing new, low-cost membranes that can operate at these higher temperatures. A new series of organically modified siloxane (ORMOSIL) polymers were synthesized for use as membrane materials in a high-temperature PEM fuel cell. These polymers have an organic portion that can allow protons to transport through the polymer film and a cross-linked silica network that gives the polymers dimensional stability. These flexible xerogel polymer films are thermally stable, with decomposition onset as high as 380 C. Two types of proton-conducting ORMOSIL films have been produced: (1) NASA-A, which can coordinate many highly acid inorganic salts that facilitate proton conduction and (2) NASA-B, which has been produced and which incorporates strongly acidic (proton donating) functional groups into the polymer backbone. Both of these polymer films have demonstrated significantly higher proton conductivity than Nafion at elevated temperatures and low relative humidities. An added advantage is that these polymers are very inexpensive to produce because their starting materials are commodity chemicals that are commercially available in large volumes.

Kinder, James D.↗
DOE OSTI2020

Dynamic System Scaling Applied to Zr-4 Cladding under RIA Conditions

The research and development lifecycle for new fuel designs currently has an ideal 20-25 year timeline. Efforts are currrently underway to accelerate fuel design and development using high performance fuel modeling codes and reduced scale experiments with new instrumentation techniques. However current tools available require a full scale prototype to be designed and tested for fuel qualification. The thermal-hydraulics community has leveraged scaling methodologies to use reduced scale integral effect test facilities (Westinghouse AP600/1000, NuScale Power Module) in lieu of building full scale prototypes for reactor design certification. Dynamic System Scaling (DSS) is a recent development to scaling methodologies that enable the tracking and quantification of dynamic scaling distortions experienced throughout a transient. Recent TREAT experiments performed reactivity initiated accident (RIA) pulses on UO2 fuel rodlets in Zr-4 cladding and were accompanied by BISON predictions for the cladding temperature. DSS is applied to pyrometer data of outer cladding temperatures and two BISON predictions after peak cladding temperature has been reached. One BISON case uses a constant gap conductance value between the fuel and cladding and the other using a conventional gap conductance model. Results from the DSS analysis show that there is good agreement between both BISON predictions and the experimental data and that there is not a significant distortion seen between using either gap conductance model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1979

Commercial phosphoric acid fuel cell system technology development

Reducing cost and increasing reliability were the technology drivers in both the electric utility and on-site integrated energy system applications. The longstanding barrier to the attainment of these goals was materials. Differences in approaches and their technological features, including electrodes, matrices, intercell cooling, bipolar/separator plates, electrolyte management, fuel selection, and system design philosophy were discussed.

Prokopius, P. R.↗
DOE OSTI2025

Micromechanical Properties of the SiC and Pyrolytic Carbon Layers in Tristructural-Isotropic Coated Particles

Tristructural isotropic (TRISO) coated particle fuel was initially developed for high temperature gas cooled reactors (HTGR) and has been proposed for several other advanced reactor concepts. The design of TRISO particles focuses on preventing the release of fission products in normal and off-normal reactor conditions. The particle design features an actinide bearing fuel kernel that is surrounded by three pyrolytic carbon (PyC) layers and a silicon carbide layer (SiC). The mechanical stability of the particle and fission product retention for both metallic and gaseous fission products depend on the SiC layer. Post irradiation examination (PIE) of TRISO fuel from the first two US DOE Advanced Gas Reactor Fuel Development and Qualification Program irradiation campaigns, AGR-1 and AGR-2, had identified a low rate of particles exhibiting cracking in the SiC layer that did not propagate across the SiC layer. While cracking in the SiC is rare for test conditions and particles associated with the AGR program, understanding the stress state and mechanical properties of the SiC and PyC layers related to particle architecture can aid predicting thermomechanical response of TRISO fuel under the prescribed operation envelope and beyond as well as aiding in the development of similar fuel concepts for other advanced reactors. The presented investigation shows the relationship of the mechanical properties and mechanical response (e.g., understanding crack propagation) of the SiC and PyC layers relative to position within the particle. Testing was conducted on the inner and outer PyC layers of TRISO particles to quantify differences in mechanical behavior.

Montoya, Katherine [ORNL] (ORCID:0000000326955086)↗
NASA NTRS1993

Space Exploration Initiative Fuels, Materials and Related Nuclear Propulsion Technologies Panel

This report was prepared by members of the Fuels, Materials and Related Technologies Panel, with assistance from a number of industry observers as well as laboratory colleagues of the panel members. It represents a consensus view of the panel members. This report was not subjected to a thorough review by DOE, NASA or DoD, and the opinions expressed should not be construed to represent the official position of these organizations, individually or jointly. Topics addressed include: requirement for fuels and materials development for nuclear thermal propulsion (NTP) and nuclear electric propulsion (NEP); overview of proposed concepts; fuels technology development plan; materials technology development plan; other reactor technology development; and fuels and materials requirements for advanced propulsion concepts.

Bhattacharyya, S. K.↗
DOE OSTI2022

Geologic Disposal Safety Assessment (GDSA) Biosphere Model Development

The Spent Fuel and Waste Science and Technology Campaign of the U.S. Department of Energy Office of Nuclear Energy, Office of Spent Fuel and Waste Disposition is conducting research and development on geologic disposal of spent nuclear fuel and high-level nuclear waste. This work includes the Geologic Disposal Safety Assessment (GDSA) program which is charged with development of generic deep geologic repository concepts and system performance assessment models. One part of the GDSA framework is the development of a biosphere model capable of assessing doses to potential receptors exposed to radionuclides released from geologic disposal sites. As part of the GDSA framework, a biosphere model compatible with the PFLOTRAN massively parallel subsurface flow and reactive transport code is under development. The PFLOTRAN model provides the radionuclide source term for the biosphere model. The GDSA Biosphere model then assesses the potential movement of radionuclides through the surface biosphere and the subsequent exposure to a human receptor living in the biosphere. The biosphere model includes pathways originating from the groundwater as well as pathways originating from surface water bodies that have a water exchange with a contaminated groundwater body. The pathways for human exposure include consumption of drinking water, irrigated crops, meat animals, aquatic vegetation, and animals, etc.; external exposure from irrigated ground surfaces, surface water bodies, recreational activities, etc.; and inadvertent exposures such as ingestion of contaminated soils or shower water, etc. The GDSA Biosphere model was designed to be flexible and generic in order to accommodate a variety of different sites and climate states. This presentation will present the on the purpose, design, and development progress of the GDSA Biosphere Model.

GDSA, biosphere, repository↗
DOE OSTI2022

Evaluation of the Effect of Burnup Acceleration on UO 2 Microstructure Evolution

Accelerated fuel qualification (AFQ) is a methodology by which new nuclear fuels are developed in an accelerated time frame compared with historical fuel qualification approaches. AFQ generally relies on high-fidelity physics-based modeling and simulation tools to adequately describe fuel performance as well as on revolutionary methods to accelerate burnup accumulation and collect relevant data more quickly. This report summarizes the use of advanced fuel modeling and simulation tools to evaluate microstructures from commercially irradiated fuel and microstructures from proposed MiniFuel irradiations, in which burnup accumulation is accelerated while prototypic temperature conditions are maintained. In this milestone, we used the mesoscale fuel performance code MARMOT to model the evolution of irradiated UO 2 microstructures and their potential restructuring at high burnup. The simulation conditions were informed by BISON models of both commercially irradiated fuel and MiniFuel. A first set of simulations investigated the recrystallization behavior of fully dense microstructures and showed full recrystallization at burnups as low as 52 MWd/kgU at 950°C. However, these simulations did not account for the presence of fission gas bubbles (predicted by BISON). Therefore, a second set of simulations including fission gas bubbles was performed and indicated that at the lowest temperature considered (650°C), the porous UO 2 microstructures have the highest total Gibbs free energies and are likely to recrystallize earlier than higher temperature cases (800 and 950°C), which agrees with high-burnup fuel characterization data. The results also showed that at lower temperature (650°C), the total free energies of the PWR fuel and MiniFuel microstructures are not significantly different. However, at the highest temperature (950°C), MiniFuel microstructures have a lower free energy than that of the PWR fuel microstructure. The competing effects between the temperature-dependent grain nucleation rate and the reduction of the free energy of the microstructure at higher temperature as a result of diffusion indicated that restructuring may occur at even higher temperatures than those considered in this study. In addition to the microstructure evolution modeling efforts, the burnup gradient across a single fuel specimen was also considered. This evaluation was for the VXF-15 position of the High Flux Isotope Reactor (HFIR) using the code suite HFIRCON, which was developed to automate the workflow for evaluating targets and fuel as they are irradiated in HFIR. The burnup gradient evaluation showed a dependence on both the axial and radial locations within the specimen, with a maximum difference of 1.7 between the inner and outermost radial layers. This relationship was further supported by considering the fission product speciation with respect to location within the specimen, which showed a higher concentration of 239 Pu, 240 Pu, and 241 Pu on the outer radial locations of the specimen than the center. The findings of the burnup and speciation evaluation show that some amount of self-shielding is occurring in the specimen when irradiated in the high-flux environment of HFIR; however, this impact is more pronounced for natural uranium when compared to 6% enrichment due to the higher ratio of 238 U in the specimen. Further analyses are required to understand the sensitivity of this gradient to spatial mesh and enrichment of the specimen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Model Development for Multi-Component Fuel Vaporization and Flash Boiling

The objectives of this project are to improve the multi-component fuel droplet and film vaporization models used in internal combustion engine simulation, and to develop a comprehensive model to predict the characteristics of multi-component flash boiling spray. This work explores two approaches to fuel composition treatment for modeling multi-component fuel vaporization: one based on discretization and surrogates, and the other based on continuous thermodynamic distribution of fuel properties. The experimental data collected for model validation are done under three fuel form factors: droplet, spray, and thin film. The study on sprays also include experimentation under non-flash and flash boiling conditions, a phenomenon that enhances fuel vaporization. The main goals of this work are: Design and develop a multi-component fuel droplet and wall film vaporization model using both discrete and continuous thermodynamics methods. Design and develop an analytical model for multi-component flash boiling. Integrate the multi-component droplet and film model into multi-dimensional engine calculations to predict the fuel vaporization process under engine operation condition. Conduct multi-component droplet and fuel film vaporization experiments in a non-combusting chamber to verify the proposed vaporization models. Characterize flash boiling phenomena of multi-component fuel sprays by optical and laser diagnostic techniques. This report will detail the experimental setup and the numerical basis for developing a model to achieve the main goals listed above. Key features of observed multi-component fuel vaporization will be summarized at the end of each experimental sections, and corresponding model performance evaluation will be presented at the end of each model development section.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Development of a U-19Pu-10Zr fuel performance benchmark case based on the IFR-1 experiment

Metallic nuclear fuels are subject to research and development for use in advanced reactors. Robust, accurate metallic fuel performance models are important for the design, safety analysis, and licensing of these reactors. However, metallic fuel performance models require additional development; they are not as mature as UO 2 fuel performance models. A benchmark case based on the IFR-1 experiment was developed to better gauge the accuracy of existing models, identify models for high-priority development, and potentially quantify any future improvements made by further model development.This work collected publicly available information on the IFR-1 experiment and used it to develop the benchmark case. Fuel behavior during the IFR-1 irradiation was simulated by using the fuel performance code BISON, and the predicted results were compared with postirradiation examination data from the IFR-1 experiment. Furthermore, a sensitivity study and tuning studies were performed as a preliminary investigation into the causes of inaccurate temperature and dimensional change predictions.The benchmark predicted reasonably accurate values for the burnup and fission gas release. There was error in the predicted temperatures, which could be explained by uncertainty in the input parameters and legacy temperatures. BISON over-predicted dimensional changes in the fuel and cladding. The sensitivity study showed that the dimensional changes were most sensitive to the fuel swelling anisotropy and the cladding void swelling model. Future benchmark and model development should focus on cladding swelling behaviors to improve dimensional change predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗