Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fluid interfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Investigation of Elastodynamic Nonlinear Response of Dry Intact, Fractured and Saturated Rock

Nonlinear elastodynamic response of fractured rocks carries crucial information on fracture features that can be exploited to forecast flow properties, friction constitutive behavior and poromechanical response. Well-controlled laboratory experiments are designed to measure the nonlinear elastodynamic response of Westerly granite in three states: dry intact, dry fractured and saturated fractured. We study the effect of fracturing and saturation in modifying the elastodynamic response of the rock. Each sample is tested at a normal stress level of 15 MPa. We measure the elastodynamic response of an intact L-shaped sample of Westerly Granite subjected to normal stress oscillations of prescribed amplitudes (0.2–1 MPa) and frequencies (0.1, 1, 10 Hz). Ultrasonic waves transmitted across the sample are used to monitor the evolution of wave velocity before, during and after dynamic stressing. Furthermore, the nonlinearity of the elastodynamic response is measured in terms of: (1) the offset in normalized wave velocity; (2) the amplitude of wave velocity fluctuation during the oscillations; and (3) recovery rate of the wave velocity post-oscillation. We observe that the three nonlinearity parameters show a similar trend. Irrespective of the parameter, the nonlinearity measures higher for sample in dry-intact condition than that for dry-fractured and the saturated-fractured sample exhibits smaller nonlinearity than the dry-fractured sample. As expected, the saturated sample exhibits less nonlinearity than the dry intact and fractured samples due to the presence of interstitial fluid and the resulting increased interface stiffness. Conversely, the dry intact rock shows a higher nonlinearity than the dry fractured. We use numerical simulations to show that the presence of fracture significantly alters the strain distribution across the bulk of the sample and only the contacting asperities are highly strained, thus resulting in a decrease in the measured elastodynamic nonlinearity.

58 GEOSCIENCES↗
DOE OSTI2022

Shallow Cumulus Entrainment Dynamics in a Sheared Environment

Abstract Vertical wind shear has long been known to tilt convective towers and reduce thermal ascent rates. The purpose of this study is to better understand the physical mechanisms responsible for reduced ascent rates in shallow convection. In particular, the study focuses on cloud-edge mass flux to assess how shear impacts mass-flux profiles of both the ensemble and individual clouds of various depths. A compositing algorithm is used to distill large-eddy simulation (LES) output to focus on up- and down-shear cloud edges that are not influenced by complex cloud geometry or nearby clouds. A direct entrainment algorithm is used to estimate the mass flux through the cloud surface. We find that the dynamics on the up- and down-shear sides are fundamentally different, with the entrainment of environmental momentum and dilution of buoyancy being primarily responsible for the reduced down-shear ascent rates. Direct estimates of fluid flow through the cloud interface indicate a counter-shear organized flow pattern that entrains on the down-shear side and detrains on the up-shear side, resulting from the subcloud shear being lifted into the cloud layer by the updraft. In spite of organized regions of entrainment and detrainment, the overall net lateral mass flux remains unchanged with respect to the no shear run, with weak detrainment present throughout cloud depth.

Meteorology & Atmospheric Sciences↗
DOE OSTI2024

Discoveries in Blast-Driven Turbulence of Astrophysical Relevance

The fluid mixing caused by variable-density instabilities is important in a wide variety of scenarios from ocean mixing and astrophysical phenomena to nuclear fusion techniques and atomic weapons. This thesis explores the mixing resulting from a specific instability known as the Blast Driven Instability (BDI). This work investigates the variable density mixing in an explosively driven environment due to the fluid instabilities at the material interfaces. Specifically, diverging Richtmyer-Meshkov (impulsive-acceleration environment) and Rayleigh-Taylor (variable-acceleration environment) instabilities (present in supernova and inertial confinement fusion) are studied using advanced high-speed diagnostics in carefully designed laboratory experiments. The BDI morphology is presented through a time development of Mie scattering images, and steps through the parameter space (varying density ratio and driver speed), highlighting the development of the structures that form during mixing. A scaling criterion is used to relate the two systems of vastly different spatiotemporal scales. Velocity fields in the BDI have been captured for the first time using the high temporal resolution PIV technique. Subsequent analysis of the dynamics of the instability from the velocity fields illustrates the distribution of kinetic energy, the transition to turbulence, and the characteristic growth of the instability are discussed. This study furthers understanding of how blast-driven instability pertains to supernova and inertial confinement fusion science. The morphology of the BDI has been characterized for the first time. This work steps through the parameter space covered in Mie scattering experiments, and how the different parameters contribute to development of structures and mixing. It also examines a scaling of the Atwood number for expanding predictive capabilities to other experimental conditions and simulations. The first collection of velocity fields acquired for the BDI are recorded, and subsequent analysis evaluating the distribution of kinetic energy throughout space and time for two density ratios from the overall parameter space, as well as the transition to turbulence, estimated from a Reynolds number calculated based on momentum mixing are all presented. This information is useful in advancing the development of models to predict physics of high energy density applications where experiments are not always readily available. This research has successfully demonstrated understanding for the time criteria defining regimes where the shock driven (Richtmyer-Meshkov instability) and the buoyancy driven (Rayleigh-Taylor instability) dominates through a parametric study of density variation (Atwood number) and driver speed (Mach number). All this furthers understanding of how the BDI pertains to SN and ICF.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Nuclear Thermal Energy Storage Configurations for Industrial Combined Heat and Power Supply: Conceptual Study and Engineering Designs

The industries examined in this report primarily rely on moderate-temperature heat provided by gas- or coal-fired boilers and combined heat and power (CHP) plants, delivered through standard process steam systems. High-temperature energy demands are often industry-specific and typically exceed the capabilities of high-temperature gas-cooled reactors (HTGRs). While it is technically feasible to replace process steam from fossil-based heat sources with nuclear energy, certain industries, such as methanol production and pulp and paper, face technoeconomic challenges in integrating nuclear energy without major changes or a technological shift. This is mainly due to the limited external energy demand remaining after the use of internal byproducts, waste heat recovery, and simple efficiency improvements. Achieving full decarbonization of these processes with nuclear energy would require significant technological advancements, involving experimental technology and substantial investments, making widespread adoption in existing industrial plants unlikely in the near term. This study reviews TES options in the context of enabling a flexible CHP supply while maintaining a steady nuclear heat input. Heat storage systems that interface between the reactor primary fluid and the CHP system offer superior performance and flexibility. Specifically, steam extraction downstream of the reheater with a two-tank molten-salt TES appears as the best solution regarding thermodynamic system benefits and system drawbacks. Using selected system configurations, a conceptual design of an industrial energy park was developed for industries with varying energy demands, such as steel production plants utilizing electric arc furnaces (EAFs) and chemical plants, as well as for those with constant energy demands, like petroleum refineries. This design highlights the capabilities of TES and explores its potential business cases. The study also conceptually develops the potential for integrating additional energy sources with nuclear systems through the implementation of TES. The potential of the HTGR-TES-CHP system was also evaluated considering key uncertainties such as industrial demand profiles, external grid access availability, and eligible tax credit levels, using the Holistic Energy Resource Optimization Network. Sensitivity of net present value to these uncertainties was analyzed to determine the optimal number of nuclear reactors (and CHP systems) and the suitable TES capacity. The results were interpreted from a decision-maker’s perspective, focusing on three key areas: deployment strategy (oversized units vs. undersized units with TES support), industrial process characteristics (thermal-intensive single profiles vs. electricity-intensive combined profiles), and operational goals (maximizing profits vs. minimizing natural gas (NG) consumption or external grid dependence). The optimization results indicate that the HTGR-TES-CHP system significantly reduces reliance on NG boilers for individual industrial processes by 9-60% (in NG capacity factor), with an average reduction of 38%, compared to standalone NG boiler operation case (Business As Usual [BAU]). For combined industrial processes, the reduction ranges from 37-77%, with an average of 60%. Additionally, the system greatly reduces dependence on external grids. In meeting industrial electrical demands, a 33-100% self-sufficient internal electricity supply is achieved for single industrial process, with an average of 74%, compared to the BAU scenario, where 100% of electricity is imported. For combined processes, 35-100% of internal electricity demands are met by the reactor, with an average of 73%. At last, the relative NG price levels at which the proposed HTGR-TES-CHP system can cost-effectively enter the market currently dominated by existing NG boilers were estimated. For a moderate HTGR CAPEX level ($\$$2500/kWth, $\$$6329/kWe), the analysis suggests that NG prices must be 2.5 to 7 times higher than HTGR variable operating and maintenance costs for single industrial process, and 5.5 to 9.5 times higher for a combined process scenario. Tax credit modeling shows that the Investment Tax Credit significantly reduces the price threshold needed to break even, making the system competitive with NG boilers in certain cases.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1975

Heat flow and convection experiments aboard Apollo 17

Experiments conducted aboard Apollo 17 showed that in uncovered liquids, convection driven by surface tension can occur at lower temperature gradients in low gravity than in 1 g. In completely confined fluids (no liquid-gas interface), vibrations caused by spacecraft and astronaut movements increased the heat transfer considerably over the pure conduction case.

Grodzka, P. G.↗
NASA NTRS1978

Solar wind stream interfaces

Results are presented for a superposed epoch analysis of discontinuous solar wind interfaces. The average time-space profiles of stream interfaces are discussed with reference to fluid properties (flow speed, pressure ridge, density, electron and proton temperatures) and kinetic properties (electron core and halo, flow speed fluctuations, electron heat flux, alpha particles). Other aspects of stream interfaces are described, such as the persistence of individual interfaces, shock associations, the sector boundaries of the interplanetary magnetic field, and sudden impulses in the geomagnetic field. Interface position is considered in terms of the observed temperature jump. A conceptual model of high-speed stream evolution is proposed.

Gosling, J. T.↗
NASA NTRS1985

Simulation of turbulent mixing layers

A hybrid numerical scheme, combined with a scalar convection scheme, is used to compute turbulent mixing layers. The hybrid scheme is used to solve the vorticity equation by dividing the domain into two regions, applying a Lagrangian method in one region and an Eulerian method in the other. The scalar convection scheme is used to track an interface which separates a dyed fluid from a dye-free fluid, thereby distinguishing the fluid that starts on the high speed side from the fluid that starts on the low speed side. A two-dimensional mixing layer has been simulated using this new method; the roll up of a vortex sheet into structures that interact and pair is observed. The growth of the momentum thickness and the development of the mean turbulence statistics are found to be consistent with experimental observations. Forcing of the layer at moderate and low frequencies shows a dramatic effect on the growth of the momentum thickness and the entrainment ratio. Low frequency forcing enhances the growth of the layer; moderate frequency forcing inhibits the growth.

Mansour, N. N.↗
NASA NTRS1984

Thermal convection during Bridgman crystal growth

Numerical experiments are used to study thermally driven flows which occur during vertical Bridgman crystal growth of a single component fluid. The solid-liquid interface was specified as parabolic and flow patterns were calculated for various insulation thicknesses, Grashof, Prandtl, and Biot numbers. When the melt is on top and the gravity vector is axially downward it is shown that flow persists as long as a radial temperature gradient is present. If the interface is convex, as viewed from the liquid, a single cell is observed. A concave interface exhibits multiple counterrotating cells. The insulation thickness and Grashof, Prandtl, and Biot numbers influence the flow in a quantitative manner.

Carlson, Frederick M.↗
NASA NTRS1988

Flight projects overview

Information is given in viewgraph form on the activities of the Flight Projects Division of NASA's Office of Aeronautics and Space Technology. Information is given on space research and technology strategy, current space flight experiments, the Long Duration Exposure Facility, the Orbiter Experiment Program, the Lidar In-Space Technology Experiment, the Ion Auxiliary Propulsion System, the Arcjet Flight Experiment, the Telerobotic Intelligent Interface Flight Experiment, the Cryogenic Fluid Management Flight Experiment, the Industry/University In-Space Flight Experiments, and the Aeroassist Flight Experiment.

Levine, Jack↗
NASA NTRS1991

Axial forcing of an inviscid finite length fluid cylinder

Current interest in microgravity materials processing has focused attention upon the finite fluid column. This configuration is used in the modeling of float zones. In this paper the incompressible inviscid finite length fluid column is subjected to an axial, time-dependent disturbance. The response of the fluid system and the resulting interface location are determined via Laplace transform methods.

Lyell, M. J.↗
NASA NTRS1991

Rotational fluid flow experiment: WPI/MITRE advanced space design GASCAN 2

The design and implementation is examined of an electro-mechanical system for studying vortex behavior in a microgravity environment. Most of the existing equipment was revised and redesigned as necessary. Emphasis was placed on the documentation and integration of the mechanical and electrical subsystems. Project results include the reconfiguration and thorough testing of all the hardware subsystems, the implementation of an infrared gas entrainment detector, new signal processing circuitry for the ultrasonic fluid circulation device, improved prototype interface circuits, and software for overall control of experiment design operation.

Daly, Walter F.↗
NASA NTRS1991

Electrophoresis of small particles and fluid globules in weak electrolytes

An examination is conducted of the influence of partial ionization on the electrophoresis of small particles and fluid globules, with a view to the nature of conditions under which dissociation-association (D-A) alters electrokinetics. It is found that, since D-A processes are important in cases where double-layer polarization and relaxation would otherwise prevail, the predicted effect on electrophoretic mobility is greatest for the drops and bubbles whose surfaces are fluid and convection within the interface is significant. While the computation scheme used applies only to situations where forcing-field magnitude is small, the results obtained indicate that D-A processes involving ionogenic solutes may be significant in apolar liquids where electrokinetic phenomena are driven by strong forcing fields.

Baygents, J. C.↗
NASA NTRS1991

Rotational fluid flow experiment

This project which began in 1986 as part of the Worcester Polytechnic Institute (WPI) Advanced Space Design Program focuses on the design and implementation of an electromechanical system for studying vortex behavior in a microgravity environment. Most of the existing equipment was revised and redesigned by this project team, as necessary. Emphasis was placed on documentation and integration of the electrical and mechanical subsystems. Project results include reconfiguration and thorough testing of all hardware subsystems, implementation of an infrared gas entrainment detector, new signal processing circuitry for the ultrasonic fluid circulation device, improved prototype interface circuits, and software for overall control of experiment operation.

Source record↗
NASA NTRS1998

Application of a Modified Gas Chromatograph to Analyze Space Experiment Combustion Gases on Space Shuttle Mission STS-94

A space experiment designed to study the behavior of combustion without the gravitational effects of buoyancy was launched aboard the Space Shuttle Columbia on July 1, 1997. The space experiment, designated as Combustion Module-1 (CM-1), was one of several manifested on the Microgravity Sciences Laboratory - 1 (MSL-1) mission. The launch, designated STS-94, had the Spacelab Module as the payload, in which the MSL-1 experiments were conducted by the Shuttle crewmembers. CM-1 was designed to accommodate two different combustion experiments during MSL-1. One experiment, the Structure of Flame Balls at Low Lewis-number experiment (SOFBALL), required gas chromatography analysis to verify the composition of the known, premixed gases prior to combustion, and to determine the remaining reactant and the products resulting from the combustion process in microgravity. A commercial, off-the-shelf, dual-channel micro gas chromatograph was procured and modified to interface with the CM-1 Fluids Supply Package and the CM-1 Combustion Chamber, to accommodate two different carrier gases, each flowing through its own independent column module, to withstand the launch environment of the Space Shuttle, to accept Spacelab electrical power, and to meet the Spacelab flight requirements for electromagnetic interference (EMI) and offgassing. The GC data was down linked to the Marshall Space Flight Center for near-real time analysis, and stored on-orbit for post-flight analysis. The gas chromatograph operated successfully during the entire SOFBALL experiment and collected 309 runs. Because of the constraints imposed upon the gas chromatograph by the CM-1 hardware, system and operations, it was unable to measure the gases to the required accuracy. Future improvements to the system for a re-flight of the SOFBALL experiment are expected to enable the gas chromatograph to meet all the requirements.

Coho, William K.↗
NASA NTRS1998

Arcjet Semi-Elliptic Nozzle Simulations and Validation in Support of TPS Testing

Much of the ground based testing of advanced thermal protection system (TPS) components for the X33 program is done in arc-heated wind tunnels such as those located in the Arc-Jet Complex at NASA Ames Research Center. These facilities are capable of simulating the high temperature, chemically reacting flow environment experienced by the vehicle during flight. This allows one to test critical design issues such as maximum reuse temperatures, seals, gaps, and increases in heating due to interfaces between different materials. Computational fluid dynamics (CFD) has evolved to the point where it now can be used in the vehicle design process for accurate and timely prediction of trajectory based aerothermal heating environments for re-entry vehicles. It can also be used for simulation of the flow environments in ground based facilities such as arcjets. By utilization of the same CFD code and solution methodology, the important differences between ground test and flight may be quantified. The goal of this paper is to utilize CFD to provide validated simulations of the flow environment in the NASA-Ames semi elliptic nozzle arcjet facilities. The validation of the ground simulations will come From comparison to existing calibration data. Specific tests in support of the X33 TPS test program will ilso be simulated. In this manner, the differences between the ground test simulation and the flight environment can be identified for a measure of ground test to flight traceability.

Loomis, Mark↗
NASA NTRS2006

Rapid Aeroelastic Analysis of Blade Flutter in Turbomachines

The LINFLUX-AE computer code predicts flutter and forced responses of blades and vanes in turbomachines under subsonic, transonic, and supersonic flow conditions. The code solves the Euler equations of unsteady flow in a blade passage under the assumption that the blades vibrate harmonically at small amplitudes. The steady-state nonlinear Euler equations are solved by a separate program, then equations for unsteady flow components are obtained through linearization around the steady-state solution. A structural-dynamics analysis (see figure) is performed to determine the frequencies and mode shapes of blade vibrations, a preprocessor interpolates mode shapes from the structural-dynamics mesh onto the LINFLUX computational-fluid-dynamics mesh, and an interface code is used to convert the steady-state flow solution to a form required by LINFLUX. Then LINFLUX solves the linearized equations in the frequency domain to calculate the unsteady aerodynamic pressure distribution for a given vibration mode, frequency, and interblade phase angle. A post-processor uses the unsteady pressures to calculate generalized aerodynamic forces, response amplitudes, and eigenvalues (which determine the flutter frequency and damping). In comparison with the TURBO-AE aeroelastic-analysis code, which solves the equations in the time domain, LINFLUX-AE is 6 to 7 times faster.

Trudell, J. J.↗
DOE OSTI2021

Algae cultivation systems and methods with bore waves

An algae cultivation system includes generating a translating hydraulic jump wave that travels across a gas-liquid interface of an algae cultivation fluid contained in the algae cultivation system. The translating hydraulic jump wave has Froude number greater than 1.

Hazlebeck, David A.↗
NASA NTRS2002

Crystal Growth of ZnSe and Related Ternary Compound Semiconductors by Vapor Transport

The objective of the project is to determine the relative contributions of gravity-driven fluid flows to the compositional distribution, incorporation of impurities and defects, and deviation from stoichiometry observed in the crystals grown by vapor transport as results of buoyance-driven convection and growth interface fluctuations caused by irregular fluid-flows. ZnSe and related ternary compounds, such as ZnSeS and ZnSeTe, were grown by vapor transport technique with real time in-situ non-invasive monitoring techniques. The grown crystals were characterized extensively to correlate the grown crystal properties with the growth conditions. The following are the research progress in the past two years. In-situ monitoring of partial pressure by optical absorption technique and visual observation of the growing crystal were performed during vapor growth of ZnSe. Low-temperature photoluminescence (PL) spectra and glow discharge mass spectroscopy (GDMS) were measured on ZnSe starting materials provided by various vendors and on bulk crystals grown from these starting materials by physical vapor transport (PVT) to study the effects of purification and contamination during crystal growth process. Optical characterization was performed on wafers sliced from the grown crystals of ZnSe, ZnTe and ZnSe(1-x),Te(x), (0<x<0.4). Energy band gaps at room temperature were determined from optical transmission measurements and a best fit curve to the band gap vs. composition, x, data gives a bowing parameter of 1.45. Low-temperature photoluminescence (PL) spectra of ZnSe and ZnTe were dominated by near band edge emissions and no deep donor-acceptor pairs were observed. The PL spectrum exhibited a broad emission for the ZnSe(1-x),Te(x), samples, 0.09<x<0.39. The single broad PL emission spectra and the spectra measured as a function of temperature were interpreted as being associated with the exciton bound to Te clusters because of the high Te content in these samples. To validate numerical codes, in-situ monitoring during the PVT of HgI2 was designed. Optical absorption spectra of the vapor phase over HgI2 were measured for wavelengths between 200 and 600nm at sample temperatures between 349 and 610K. The Beer's Law constants for 15 wavelengths between 200 and 440 nm were determined. From these constants the vapor pressure of HgI2 was established as a function of temperature for the liquid and the solid Beta-phases To characterize the growth conditions during the PVT growth of In-doped ZnSe the optical absorbance of the vapor phase over the In-Se system were measured and were used to obtain the partial pressures of Se2(g) and In2Se(g).

Su, Ching-Hua↗