Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Computations of Flow Over a Hump Model Using Higher Order Method With Turbulence Modeling

Turbulent separated flow over a two-dimensional hump is computed by solving the RANS equations with k-omega (SST) turbulence model for the baseline, steady suction and oscillatory blowing/suction flow control cases. The flow equations and the turbulent model equations are solved using a fifth-order accurate weighted essentially nonoscillatory (WENO) scheme for space discretization and a third order, total variation diminishing (TVD) Runge-Kutta scheme for time integration. Qualitatively the computed pressure distributions exhibit the same behavior as they are observed in the experiments. The computed separation regions are much longer than that are observed. However, the percentage reduction in the separation region in the steady suction case is closer to that was measured in the experiment. The computations did not predict the expected reduction in the separation length in the oscillatory case. The predicted turbulent quantities are two to three times smaller than that are measured and it points towards the deficiencies in the existing turbulent models when they are applied to strong steady/unsteady separated flows.

Balakumar, Ponnampalam↗
NASA NTRS1990

An abbreviated Reynolds stress turbulence model for airfoil flows

An abbreviated Reynolds stress turbulence model is presented for solving turbulent flow over airfoils. The model consists of two partial differential equations, one for the Reynolds shear stress and the other for the turbulent kinetic energy. The normal stresses and the dissipation rate of turbulent kinetic energy are computed from algebraic relationships having the correct asymptotic near wall behavior. This allows the model to be integrated all the way to the wall without the use of wall functions. Results for a flat plate at zero angle of attack, a NACA 0012 airfoil and a RAE 2822 airfoil are presented.

Gaffney, R. L., Jr.↗
NASA NTRS2013

ISSM: Ice Sheet System Model

In order to have the capability to use satellite data from its own missions to inform future sea-level rise projections, JPL needed a full-fledged ice-sheet/iceshelf flow model, capable of modeling the mass balance of Antarctica and Greenland into the near future. ISSM was developed with such a goal in mind, as a massively parallelized, multi-purpose finite-element framework dedicated to ice-sheet modeling. ISSM features unstructured meshes (Tria in 2D, and Penta in 3D) along with corresponding finite elements for both types of meshes. Each finite element can carry out diagnostic, prognostic, transient, thermal 3D, surface, and bed slope simulations. Anisotropic meshing enables adaptation of meshes to a certain metric, and the 2D Shelfy-Stream, 3D Blatter/Pattyn, and 3D Full-Stokes formulations capture the bulk of the ice-flow physics. These elements can be coupled together, based on the Arlequin method, so that on a large scale model such as Antarctica, each type of finite element is used in the most efficient manner. For each finite element referenced above, ISSM implements an adjoint. This adjoint can be used to carry out model inversions of unknown model parameters, typically ice rheology and basal drag at the ice/bedrock interface, using a metric such as the observed InSAR surface velocity. This data assimilation capability is crucial to allow spinning up of ice flow models using available satellite data. ISSM relies on the PETSc library for its vectors, matrices, and solvers. This allows ISSM to run efficiently on any parallel platform, whether shared or distrib- ISSM: Ice Sheet System Model NASA's Jet Propulsion Laboratory, Pasadena, California uted. It can run on the largest clusters, and is fully scalable. This allows ISSM to tackle models the size of continents. ISSM is embedded into MATLAB and Python, both open scientific platforms. This improves its outreach within the science community. It is entirely written in C/C++, which gives it flexibility in its design, and the power/speed that C/C++ allows. ISSM is svn (subversion) hosted, on a JPL repository, to facilitate its development and maintenance. ISSM can also model propagation of rifts using contact mechanics and mesh splitting, and can interface to the Dakota software. To carry out sensitivity analysis, mesh partitioning algorithms are available, based on the Scotch, Chaco, and Metis partitioners that ensure equal area mesh partitions can be done, which are then usable for sampling and local reliability methods.

Larour, Eric↗
NASA NTRS1993

Computational fluid dynamic modelling of cavitation

Models in sheet cavitation in cryogenic fluids are developed for use in Euler and Navier-Stokes codes. The models are based upon earlier potential-flow models but enable the cavity inception point, length, and shape to be determined as part of the computation. In the present paper, numerical solutions are compared with experimental measurements for both pressure distribution and cavity length. Comparisons between models are also presented. The CFD model provides a relatively simple modification to an existing code to enable cavitation performance predictions to be included. The analysis also has the added ability of incorporating thermodynamic effects of cryogenic fluids into the analysis. Extensions of the current two-dimensional steady state analysis to three-dimensions and/or time-dependent flows are, in principle, straightforward although geometrical issues become more complicated. Linearized models, however offer promise of providing effective cavitation modeling in three-dimensions. This analysis presents good potential for improved understanding of many phenomena associated with cavity flows.

Deshpande, Manish↗
NASA NTRS1987

Fluid particle motion and Lagrangian velocities for pulsatile flow through a femoral artery branch model

A flow visualization study using selective dye injection and frame by frame analysis of a movie provided qualitative and quantitative data on the motion of marked fluid particles in a 60 degree artery branch model for simulation of physiological femoral artery flow. Physical flow features observed included jetting of the branch flow into the main lumen during the brief reverse flow period, flow separation along the main lumen wall during the near zero flow phase of diastole when the core flow was in the downstream direction, and inference of flow separation conditions along the wall opposite the branch later in systole at higher branch flow ratios. There were many similarities between dye particle motions in pulsatile flow and the comparative steady flow observations.

Cho, Y. I.↗
NASA NTRS1991

Modeling of linear isentropic flow systems

A modeling approach for linear isentropic flow systems based on the quasi-one-dimensional Euler equations of non-viscous, compressible flow are presented. Such systems are representative of certain high speed propulsion systems. Accurate models useful in control system studies are developed. A supersonic inlet is considered, and the resulting set of partial differential equations with boundary conditions is solved for a linear transfer matrix using Laplace transforms.

Sarantopoulos, Athan D.↗
NASA NTRS1991

Modeling of linear isentropic flow systems

A modeling approach for linear isentropic flow systems based on the quasi-one-dimensional Euler equations of non-viscous, compressible flow are presented. Such systems are representative of certain high speed propulsion systems. Accurate models useful in control system studies are developed. A supersonic inlet is considered, and the resulting set of partial differential equations with boundary conditions is solved for a linear transfer matrix using Laplace transforms.

Sarantopoulos, Athan D.↗
NASA NTRS1975

Shear flow aerodynamics - Lifting surface theory

A lifting surface theory based on a parallel shear flow model is presented for steady, incompressible flows. The theory is intended to account approximately for the presence of a boundary layer. The method of Fourier transforms is used to calculate the pressure on a surface of infinite extent and arbitrary contour. Immediately above the surface is a region of sheared flow (the boundary layer), outside of which the flow velocity is constant. The Fourier transform of the pressure on this surface is used to derive the shear flow equivalent to the kernel function of classical potential flow lifting surface theory. The kernel function provides an integral relation between the upwash at a given point on the surface and the pressure everywhere on the surface. This relation is treated as an integral equation for the pressure, and is solved numerically. Computations are presented for the lift and pitching moment on a flat plate in two-dimensional flow, and for flat, rectangular wings of aspect ratio 1, 2, and 5. As expected, the shear layer decreases the lift curve slope; however, the shear layer (whose thickness is constant along the wing chord) has little effect on the center of pressure.

Ventres, C. S.↗
NASA NTRS1977

Transmission of sound through nonuniform circular ducts with compressible mean flows

An acoustic theory is developed to determine the sound transmission and attenuation through an infinite, hard-walled or lined, circular duct carrying compressible, sheared, mean flows and having a variable cross section. The theory is applicable to large as well as small axial variations, as long as the mean flow does not separate. Although the theory is described for circular ducts, it is applicable to other duct configurations - annular, two dimensional, and rectangular. The theory is described for the linear problem, but the technique is general and has the advantage of being applicable to the nonlinear case as well as the linear case. The technique is based on solving for the envelopes of the quasi-parallel acoustic modes that exist in the duct instead of solving for the actual wave. A computer program was developed. The mean flow model consists of a one dimensional flow in the core and a quarter-sine profile in the boundary layer. Results are presented for the reflection and transmission coefficients in ducts with varying slopes and carrying different mean flows.

Nayfeh, A. H.↗
NASA NTRS1983

Tests of SSME low pressure pump in liquids at zero throughflow

Shutdown requirements in space of the Space Shuttle Main Engines require that the low pressure pump operate under conditions of zero flow and zero NPSH and still be able to generate head and absorb torque. Ground tests were conducted in both water and liquid oxygen to verify these capabilities. The test facilities are described, and the test results are presented showing the pump performance at zero flow over a wide range of NPSH conditions including zero values. The influence of operating speed, fluid medium, and internal struts upstream of the inducer are presented. A flow model schematic is presented sketching a flow field in the pump that is consistent with the observed data.

Jackson, E. D.↗
NASA NTRS1982

Gas flow environment and heat transfer nonrotating 3D program

A complete set of benchmark quality data for the flow and heat transfer within a large rectangular turning duct is provided. These data are to be used to evaluate, and verify, three-dimensional internal viscous flow models and computational codes. The analytical contract objective is to select a computational code and define the capabilities of this code to predict the experimental results obtained. Details of the proper code operation will be defined and improvements to the code modeling capabilities will be formulated. Internal flow in a large rectangular cross-sectioned 90 deg. bend turning duct was studied. The duct construction was designed to allow detailed measurements to be made for the following three duct wall conditions: (1) an isothermal wall with isothermal flow; (2) an adiabatic wall with convective heat transfer by mixing between an unheated surrounding flow; and (3) an isothermal wall with heat transfer from a uniformly hot inlet flow.

Schulz, R. J.↗
NASA NTRS1994

A vorticity dynamics based model for the turbulent dissipation: Model development and validation

A new model dissipation rate equation is proposed based on the dynamic equation of the mean-square vorticity fluctuation for large Reynolds number turbulence. The advantage of working with the vorticity fluctuation equation is that the physical meanings of the terms in this equation are more clear than those in the dissipation rate equation. Hence, the model development based on the vorticity fluctuation equation is more straightforward. The resulting form of the model equation is consistent with the spectral energy cascade analysis introduced by Lumley. The proposed model dissipation rate equation is numerically well behaved and can be applied to any level of turbulence modeling. It is applied to a realizable eddy viscosity model. Flows that are examined include: rotating homogeneous shear flows; free shear flows; a channel flow and flat plate boundary layers with and without pressure gradients; and backward facing step separated flows. In most cases, the present model predictions show considerable improvement over the standard kappa-epsilon model.

Shih, Tsan-Hsing↗
NASA NTRS1993

Heat transfer in rocket engine combustion chambers and nozzles

Complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analyses verified with appropriate test data. Finally, the component analyses will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Since test data from the NLS development program are not available, new validation heat transfer data have been sought. Suitable data were obtained from a Rocketdyne test program on a model hydrocarbon/oxygen engine. Simulations of these test data will be presented. Recent interest in the hybrid motor have established the need for analyses of ablating solid fuels in the combustion chamber. Analysis of a simplified hybrid motor will also be presented.

Anderson, P. G.↗
NASA NTRS2010

Active Flow Control Strategies Using Surface Pressure Measurements

Evaluate the efficacy of Microjets Can we eliminate/minimize flow separation? Is the flow unsteadiness reduced? Guidelines for an active control Search for an appropriate sensor. Examine for means to develop a flow model for identifying the state of flow over the surface Guidelines toward future development of a Simple and Robust control methodology

Kumar, Vikas↗
NASA NTRS2001

Modeling of dense reactive granular flows

A general model of dense granular flows derived elsewhere is here assessed to understand the validity of some of the assumptions embedded in the derivation.

granular↗
NASA NTRS2005

Particle Image Velocimetry Measurements to Evaluate the Effectiveness of Deck-Edge Columnar Vortex Generators on Aircraft Carriers

Candidate passive flow control devices were chosen from a NASA flow visualization study to investigate their effectiveness at improving flow quality over a flat-top carrier model. Flow over the deck was analyzed using a particle image velocimeter and a 1/120th scaled carrier model in a low-speed wind tunnel. Baseline (no devices) flow quality was compared to flow quality from combinations of bow and deck-edge devices at both zero and 20 degrees yaw. Devices included plain flaps and spiral cross-section columnar vortex generators attached in various combinations to the front and sides of the deck. Centerline and cross plane measurements were made with velocity and average turbulence measurements reported. Results show that the bow/deck-edge flap and bow/deck-edge columnar vortex generator pairs reduce flight deck turbulence both at zero yaw and at 20 degrees yaw by a factor of approximately 20. Of the devices tested, the most effective bow-only device appears to be the plain flap.

Landman, Drew↗