Results for “FENCES” — Page 24

NASA NTRS2019

Bounding Methods for Heterogeneous Lidar-derived Navigational Geofences

Safe Unmanned Aerial Vehicle (UAV) operations near the ground require navigation methods that avoid fixed obstacles such as buildings, power lines and trees. Aerial lidar surveys of ground structures are available with the precision and accuracy to geolocate obstacles, but the high volume of raw survey data can exceed the compute power of onboard processors and the rendering ability of ground-based flight planning maps. Representing ground structures with bounding polyhedra instead of point clouds greatly reduces the data size and can enable effective obstacle avoidance, as long as the bounding geometry envelopes the structures with high spatial fidelity. This report describes in detail four methods to compute bounding geometries of ground obstacles from lidar point clouds. The four methods are: 1) 2.5D Maximum Elevation Box, 2) 2.5D Ground Map Extrusion, 3) 3D Bounding Cylinder, and 4) 3D Bounding Box. The methods are applied to five point cloud datasets from lidar surveys of UAV flight research sites in Georgia and Virginia with an average point spacing that ranges from 0.1m to 0.6m. The methods are assessed using survey areas with geometrically heterogeneous ground structures: buildings, vegetation, power lines, and sub-meter structures such as road signs and guy wires. The 2.5D Maximum Elevation Box method is useful for simple structures. The 2.5D Ground Map Extrusion method efficiently encloses vegetation, but requires handdrawn ground footprints. The 3D Bounding Cylinder method excels at enclosing linear structures such as power lines and fences. The 3D Bounding Box method excels at enclosing planar structures such as buildings. The methods are compared on the basis of data compression and boundary fidelity on selected areas. The 2.5D methods yield the highest data compression but the polyhedra produced by them enclose significant amounts of empty space. Boundary fidelity is superior for the 3D methods, though this fidelity comes at the cost of a roughly thirtyfold lower data compression ratio than the 2.5D Maximum Elevation Box method. A mix of these output geometries is proposed for autonomous UAV navigation with limited on-board computing. Both the accuracy and spatial detail of emerging satellite-based survey technology lower than that of aerial lidar scanning survey technology. Sub-meter structures and thin linear structures are not reliably mapped at present by satellite-based surveys.

Moore, Andrew J.↗

NASA NTRS2020

Drop Size Distribution Measurements in Outer Rainbands of Hurricane Dorian at the NASA Wallops Precipitation-Research Facility

Hurricane rainbands are very efficient rain producers, but details on drop size distributions are still lacking. This study focuses on the rainbands of hurricane Dorian as they traversed the densely instrumented NASA precipitation-research facility at Wallops Island, VA, over a period of 8 h. Drop size distribution (DSD) was measured using a high-resolution meteorological particle spectrometer (MPS) and 2D video disdrometer, both located inside a double-fence wind shield. The shape of the DSD was examined using double-moment normalization, and compared with similar shapes from semiarid and subtropical sites. Dorian rainbands had a superexponential shape at small normalized diameter values similar to those of the other sites. NASA’s S-band polarimetric radar performed range height-indicator (RHI) scans over the disdrometer site, showing some remarkable signatures in the melting layer (bright-band reflectivity peaks of 55 dBZ, a dip in the copolar correlation to 0.85 indicative of 12–15 mm wet snow, and a staggering reflectivity gradient above the 0 °C level of −10 dB/km, indicative of heavy aggregation). In the rain layer at heights < 2.5 km, polarimetric signatures indicated drop break-up as the dominant process, but drops as large as 5 mm were detected during the intense bright-band period.

Merhala Thurai↗

NASA NTRS2019

Satellite Conjunction Assessment Risk Analysis for "Dilution Region" Events: Issues and Operational Approaches

An important activity within Space Traffic Management is the detection and prevention of possible on-orbit collisions between space objects. The principal parameter for assessing collision likelihood is the probability of collision, which is widely accepted among conjunction assessment practitioners; but it possesses a known deficiency in that it can produce a false sense of safety when the orbital position uncertainties for the conjuncting objects are high. The probability of collision is said to be “diluted” in such a situation and to understate the possible risk; certain approaches have been recommended by researchers to provide (largely conservative) risk estimates and remediation methodologies in these cases. The present analysis explores two of the main proposals for quantifying and remediating possible risk in the dilution region and quantifies their operational implications. These implications with regard to imputed additional workload are considerable, especially in anticipating the conjunction event levels expected with the deployment of the USAF Space Fence radar. This effort has been undertaken as part of a larger enterprise that seeks to clarify the philosophical and statistical underpinnings of the conjunction risk assessment process. The analysis presented herein argues that a form of hypothesis testing is implicitly used in conjunction assessment risk analysis, and that there are a number of conceptual and practical reasons for constructing the associated null hypothesis to counsel against a satellite conjunction remediation action. In short, it is concluded that, for the purposes of determining whether a conjunction remediation action should be pursued, dilution-region probabilities of collision should be treated no differently from those produced under other circumstances.

Probability of collision↗

NASA NTRS2023

Experimental Investigation of Block-TPS Fence/Gap Roughness Effects on Transition Onset and Turbulent Heating at Mach 6

An experimental investigation of boundary-layer transition and convective surface heating on wind tunnel models that simulated aeroshells comprised of multiple blocks of thermal protection system (TPS) material has been performed. Two representative entry vehicle geometries, a sphere-cone aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with varying fence heights or gap depths to represent gap fillers that either protrude above, or are recessed below, the TPS blocks due to differential ablation during reentry. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Convective surface heating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations.

Aerothermodynamics↗

NASA NTRSDate not supplied

An Overview of Ground-Based Radar and Optical Measurements Utilized By the Nasa Orbital Debris Program Office

For over 30 years, the NASA Orbital Debris Program Office (ODPO) has led the characterization of orbital debris (OD) too small to be tracked by the U.S. Space Surveillance Network (SSN), yet which may pose the greatest threat to human spaceflight and robotic missions. Measurements from specialized sensors, including ground-based radars and telescopes capable of detecting smaller objects, provide the foundation for developing statistical models to describe the current state and future evolution of the OD environment from low Earth orbit (LEO) to geosynchronous Earth orbit (GEO). Since 1990, the ODPO has partnered with the U.S. Department of Defense and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL) to collect data using the Haystack Ultrawideband Satellite Imaging Radar (HUSIR) – formerly Haystack – to characterize OD in LEO with a sensitivity of approximately 5 mm at 1000 km altitude. In addition, since 1993, the Goldstone Orbital Debris Radar, operated by NASA’s Jet Propulsion Laboratory, has provided data on OD as small as approximately 2-3 mm for altitudes below 1000 km, some of the most sensitive ground-based measurements achievable at these altitudes. Recently, collaborations with the 18 th Space Control Squadron of the U.S. Space Force have also provided the ODPO with special datasets from the Space Fence to extend coverage below the historical SSN limit of 10 cm and to characterize individual breakup events in LEO. For GEO altitudes, the Eugene Stansbery Meter Class Autonomous Telescope (ES-MCAT), a joint NASA-Air Force Research Laboratory project that reached full operational capability in 2021, collects data on debris smaller than 1 m and provides coverage of debris in historically under-sampled high-altitude orbital regimes. This paper summarizes the radar and optical sensors utilized by the ODPO, their unique capabilities, and recent datasets and applications for statistical sampling of the dynamic OD environment.

Alyssa Manis↗

NASA NTRSDate not supplied

An Overview of NASA’s Newest Engineering Model, ORDEM 4.0

Since the mid-1990s, one of the most important products produced by the NASA Orbital Debris Program Office (ODPO) has been the Orbital Debris Engineering Model (ORDEM). This series of models distills down our knowledge of the orbital debris environment to compute debris fluxes on satellites in a given orbit. This information can be used by spacecraft and upper stage designers and operators to design missions for better protection against the debris environment. The current version of the model is ORDEM 3.2, but the ODPO is working on the next generation of ORDEM, to be designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. ORDEM 4.0 will update debris populations using the most recent measurements, including radar observations by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, data from the new Space Surveillance Network Space Fence, and observations of Geosynchronous Earth Orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). The latest in situ impact data from returned hardware surfaces will be used. In addition, ORDEM 4.0 will introduce a parameterized debris shape model based on laboratory hypervelocity impact tests, such as DebriSat. This will allow analysts to implement shape characteristics in their damage equations and more accurately predict impact damage risk by debris of different shapes and orientations. This paper provides an overview of some of the new features forthcoming in ORDEM 4.0 and a status report on its development.

Mark Matney↗

NASA NTRSDate not supplied

An Overview of Ground-Based Radar and Optical Measurements Utilized By the Nasa Orbital Debris Program Office

For over 30 years, the NASA Orbital Debris Program Office (ODPO) has led the characterization of orbital debris (OD) too small to be tracked by the U.S. Space Surveillance Network (SSN), yet which may pose the greatest threat to human spaceflight and robotic missions. Measurements from specialized sensors, including ground-based radars and telescopes capable of detecting smaller objects, provide the foundation for developing statistical models to describe the current state and future evolution of the OD environment from low Earth orbit (LEO) to geosynchronous Earth orbit (GEO). Since 1990, the ODPO has partnered with the U.S. Department of Defense and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL) to collect data using the Haystack Ultrawideband Satellite Imaging Radar (HUSIR) – formerly Haystack – to characterize OD in LEO with a sensitivity of approximately 5 mm at 1000 km altitude. In addition, since 1993, the Goldstone Orbital Debris Radar, operated by NASA’s Jet Propulsion Laboratory, has provided data on OD as small as approximately 2-3 mm for altitudes below 1000 km, some of the most sensitive ground-based measurements achievable at these altitudes. Recently, collaborations with the 18 th Space Control Squadron of the U.S. Space Force have also provided the ODPO with special datasets from the Space Fence to extend coverage below the historical SSN limit of 10 cm and to characterize individual breakup events in LEO. For GEO altitudes, the Eugene Stansbery Meter Class Autonomous Telescope (ES-MCAT), a joint NASA-Air Force Research Laboratory project that reached full operational capability in 2021, collects data on debris smaller than 1 m and provides coverage of debris in historically under-sampled high-altitude orbital regimes. This paper summarizes the radar and optical sensors utilized by the ODPO, their unique capabilities, and recent datasets and applications for statistical sampling of the dynamic OD environment.

Alyssa Manis↗

NASA NTRSDate not supplied

An Overview of NASA’s Newest Engineering Model, ORDEM 4.0

Since the mid-1990s, one of the most important products produced by the NASA Orbital Debris Program Office (ODPO) has been the Orbital Debris Engineering Model (ORDEM). This series of models distills down our knowledge of the orbital debris environment to compute debris fluxes on satellites in a given orbit. This information can be used by spacecraft and upper stage designers and operators to design missions for better protection against the debris environment. The current version of the model is ORDEM 3.2, but the ODPO is working on the next generation of ORDEM, to be designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. ORDEM 4.0 will update debris populations using the most recent measurements, including radar observations by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, data from the new Space Surveillance Network Space Fence, and observations of Geosynchronous Earth Orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). The latest in situ impact data from returned hardware surfaces will be used. In addition, ORDEM 4.0 will introduce a parameterized debris shape model based on laboratory hypervelocity impact tests, such as DebriSat. This will allow analysts to implement shape characteristics in their damage equations and more accurately predict impact damage risk by debris of different shapes and orientations. This paper provides an overview of some of the new features forthcoming in ORDEM 4.0 and a status report on its development.

Mark Matney↗

NASA NTRS2024

Idaho & Oregon Agriculture: Monitoring Vegetation Impacts of Livestock Management Practices Used to Reduce Predator Conflicts on Idaho and Oregon Grazing Allotments

The practice of night penning, which involves corralling livestock into a fenced, secure area overnight, aims to safeguard animals from predators. Although this method has proven successful in minimizing interactions between livestock and wildlife, the extent of its impact on vegetation communities is still being explored. This project examines the feasibility of using Net Primary Productivity (NPP) values from the Rangeland Analysis Platform (RAP) to quantify the impacts of night penning on rangeland vegetation communities. RAP provides spatially distributed values of vegetation composition, cover, and productivity, and is derived from imagery from Landsat 5, Landsat 7 & Landsat 8 at a 30m resolution for rangelands across the United States. Our DEVELOP team partnered with Alderspring Ranch, Krebs Livestock, and the U.S Department of Agriculture Animal & Plant Health Inspection Service (APHIS) to analyze the impacts of night penning on vegetation communities. We identified control sites that captured the topographic characteristics of night pen sites used by our partners. We then quantified and compared changes in annual NPP between night pen and control sites. Our analysis of RAP NPP data, using a control-treatment design did not find impacts of night penning on vegetation. However, this was a preliminary analysis, and does not conclusively quantify the impacts of night penning on rangeland vegetation. Our analysis indicated that RAP may be a feasible tool to study livestock management impacts on rangeland vegetation; however, future studies could further validate these findings through ground observations.

Rangeland Analysis Platform (RAP)↗

NASA NTRSDate not supplied

Monitoring Vegetation Impacts of Night Penning in Idaho and Oregon Grazing Allotments Using Remote Sensing

The practice of night penning, which involves corralling livestock into a fenced, secure area overnight, aims to safeguard animals from predators. Although this method has proven successful in minimizing interactions between livestock and wildlife, the extent of its impact on vegetation communities is still being explored. In this study, we used the Rangeland Analysis Platform (RAP), which aggregates spatially distributed values of vegetation composition, cover, and productivity from the Landsat missions, to quantify the effects of night penning on rangeland vegetation communities. We identified control sites that had similar topographic characteristics to night pen sites used by ranchers in Idaho and Oregon. We then quantified and compared changes in annual net primary productivity (NPP) between night pen and control sites. Our study found that RAP NPP data did not show a noticeable difference between control sites and night penning sites. When analyzed quantitatively, night pen sites showed variability in NPP before and after night penning; however, there were few discernible differences between night pen sites and control sites, suggesting that climate conditions can have more of an effect on NPP measurements compared to land management decisions. In the summer of 2024, field crews from the Natural Resource Ecology Laboratory collected biomass data from these rangeland sites, and this will be used to compare and validate RAP products while continuing to investigate the effects of night penning.

Truman Anarella↗

NASA NTRS2024

Launch Complex 39B, SWMU 009, 2023 Performance Monitoring and Air Sparge Expansion Construction Completion Report, Kennedy Space Center, Florida

The 2023 Performance Monitoring and Construction Completion Report (PM-CCR) presents the findings, observations, and results for Air Sparging (AS) operations and expansion activities, as well as sitewide groundwater monitoring for Launch Complex 39B (LC39B), Solid Waste Management Unit (SWMU) 009, at Kennedy Space Center (KSC), Florida. The reporting period for activities covered under this PM-CCR is from January 1, 2023, to December 31, 2023. At LC39B, AS operations began in 2017 in the area west of the launch pad, in the liquid oxygen (LOX) tank area located northwest of the launch pad, and in an area outside of the perimeter fence to protect nearby Outstanding Florida Waters (OFW). The LC39B AS system was installed with 279 AS wells to depths ranging from 23 to 60 feet below land surface (bls), including the sump, correlating to top of screen depths ranging from 20 to 57 feet bls. In December 2022, a total of 22 AS wells were abandoned to support launch pad crane operations, and in November 2023, the system was expanded with five additional AS wells installed to 13 or 17 feet bls near the LOX tank. The remedial objective of the LC39B AS Interim Measure (IM) is to actively decrease concentrations of contaminants of concern (COCs) in groundwater, specifically trichloroethene (TCE), cis-1,2-Dichloroethene (cDCE), and vinyl chloride (VC), to less than their respective Natural Attenuation Default Concentrations (NADCs), so LC39B can transition into a Long-Term Monitoring (LTM) program. This PM-CCR presents the following information for LC39B: • AS system operations and maintenance (O&M) (Year 7 of operation) from January 2023 to December 2023, to include AS trailer relocation in March 2023 and subsequent replacement and re-start in June 2023. • Construction completion details for AS system expansion, which included installation of five new AS wells and one new monitoring well in November 2023. As part of expansion activities, soil samples were also collected for petroleum analysis; no exceedances were identified, and no further investigation for petroleum is warranted. • Performance monitoring results for groundwater sampling events conducted in May/June 2023 (30 wells) and November 2023 (31 wells) in the AS IM area and in the Low Concentration Plume (LCP) areas located north and east of the launch pad for volatile organic compound (VOC) analysis. • Sampling results for one monitoring well, LOX-IW0012S, which is sampled for aluminum on an annual basis (May/June 2023). This well was resampled in November 2023 for both total and dissolved aluminum. Due to a communication error with the laboratory, the May/June 2023 sample was analyzed for total aluminum only. • Groundwater sampling results for per- and polyfluoroalkyl substances (PFAS) collected from seven monitoring wells during the May/June 2023 event to further investigate the Former Sewage Treatment Plant #6 and Percolation Pond area, west of the launch pad. O&M and performance monitoring results show that the AS system at LC39B is operating as designed and meeting performance criteria. Overall runtime was 45 percent (%) during the reporting period (January to December), but the operational runtime was 78% during the timeframe when the system could run (June to December). The most significant downtime contributor was post-launch crane operations following the Artemis launch on November 16, 2022, which lasted until June 2023. During that timeframe, the AS trailer at LC39B was relocated to another KSC remediation site (Wilson Corners) and was subsequently replaced with the AS trailer from the Paint & Oil Locker (POL) remediation site at KSC to resume AS system operations. Performance monitoring results in the AS IM and LCP areas continue to show reduction in COC concentrations over time when compared to baseline levels. In 2023, only one monitoring well (MW0048) detected a COC exceeding its NADC (VC at 740 micrograms per liter [µg/L]), which marks the baseline result for this new well installed during system expansion. Across the rest of the site, VC concentrations have declined or remained stable during the 2023 sampling events. Excluding MW0048, the highest VC result in 2023 was during the May/June sampling event with a concentration of 63 µg/L at MW0032, which is located near MW0048 and the AS expansion area by the LOX tank. TCE was detected in select monitoring wells in the IM area in 2023, but only two locations exceeded the State of Florida Groundwater Cleanup Target Level (GCTL): MW0032 (21 µg/L in May/June 2023 and 9.1 µg/L in November 2023) and MW0036 (5.0 µg/L in November 2023). MW0036 is also located near the LOX tank, on the north side, where the AS system is still operational (Zone Z4). cDCE and trans-1,2-dichloroethene concentrations were less than laboratory method detection limits or their respective GCTLs in all wells sampled in 2023. Near the OFW located northwest of the launch complex, all COC concentrations were less than laboratory method detection limits from monitoring wells (MW0039, MW0040, and LOXTA0002S) sampled in 2023. Aluminum results from LOX-IW0012S, which has been sampled routinely since 2006, detected a total aluminum concentration of 3,900 µg/L during the May/June 2023 sampling event. Results from the November 2023 event detected 5,700 µg/L for total aluminum and 5,500 µg/L for dissolved aluminum. These concentrations slightly decreased from the previous year but remain relatively consistent with historical detections. Aluminum will continue to be sampled on an annual basis at this well as results still exceed the GCTL of 200 µg/L and the Upper Limit of the KSC Background Concentration of 280 µg/L. PFAS results detected nine different PFAS compounds (out of 32 analyzed) from seven wells sampled. Two PFAS compounds, perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA), currently have FDEP Provisional GCTLs of 70 nanograms per liter (ng/L). All seven samples collected resulted in concentrations less than the FDEP Provisional GCTLs for both PFAS compounds; no exceedances were observed. PFOS and PFOA also have assigned United States Environmental Protection Agency (USEPA) Maximum Contaminant Levels (MCLs) of 4 nanograms per liter (ng/L). None of the PFOS results exceeded the USEPA MCLs. PFOA was detected in two samples above the USEPA MCL at concentrations of 5.8 ng/L (ECS-IW0009I) and 5.5 ng/L (ECS-IW0009S). Three other PFAS compounds, perfluorohexanesulfonic acid (PFHxS), perfluoro-n-nonanoic acid (PFNA), and hexafluoropropylene oxide dimer acid (GenX), currently have USEPA MCLs of 10 ng/L. PFHxS, PFNA, and GenX were not detected at concentrations greater than their respective USEPA MCLs in any of the seven wells. PFAS compounds without FDEP Provisional GCTLs or USEPA MCLs were screened against USEPA RSLs. No other detections exceeded their respective USEPA RSLs. Additional PFAS sampling will be conducted as part of a future PFAS Site Assessment. Based on O&M activities and performance monitoring, the following is recommended for LC39B: • Continue with Year 8 AS system operation within Zone Z4, which includes the AS expansion area. Zone Z3, which has been off since 2018, should remain off as no rebound has been observed. Zones Z1 and Z2, which were turned off at the end of 2022, will remain shut down as monitoring well results have consistently been below GCTLs or have low-level detections with stable or decreasing trends (Meeting Minute 2402-M10, Decision 2402-D30). • Continue with performance monitoring in 2024 with the same monitoring well network as 2023, except with the addition of MW0048 in both semi-annual events. Baseline concentrations for this well were collected during the November 2023 performance monitoring event. Semi-annual sampling should be planned for the May 2024 and November 2024 timeframes (Meeting Minute 2402-M10, Decision 2402-D31). • Continue sampling monitoring well, LOX-IW0012S, for aluminum (total and dissolved) on an annual basis in May 2024. It is also recommended to re-develop this well prior to the next sampling event (Meeting Minute 2402-M10, Decision 2402-D32). The above recommendations for LC39B were presented at the February 2024 KSCRT Meeting, with Team consensus reached on the path forward. The contents of this PM-CCR were also presented at this meeting.

Deborah M Wilson↗

NASA NTRS2025

Jemez Pueblo Agriculture: Monitoring Rangeland Conditions to Inform Drought and Land Management in New Mexico

The Jemez Pueblo, a community located in the semi-arid high desert region of northcentral New Mexico, faces challenges with drought mitigation and livestock management. NASA DEVELOP partnered with the Pueblo of Jemez Natural Resources Department and The Nature Conservancy to provide recent and historical rangeland conditions to aid present decision-making, which relies on cultural practices, site familiarity, available resources, and physical data. This partnership offers the opportunity to support management practices by leveraging remote sensing and virtual fencing technologies. Our project explored Rangeland Analysis Platform (RAP) products incorporating NASA Earth observation Landsat 5 TM, Landsat 7 ETM+, Landsat 8 OLI, and Landsat 9 OLI-2 remote-sensed imagery as an agricultural land management tool. We performed linear regression analysis to evaluate RAP data to field data and explored RAP annual herbaceous biomass, ground cover trends, and climatic factors at the pasture level. We then computed study area summary statistics, performed pixel-by-pixel trend analysis across the study period, and evaluated ground cover trends near water sources. Based on available data, RAP was poorly correlated to bare ground and herbaceous biomass, generally underestimating the former and overestimating the latter. To improve the evaluation of RAP products, we suggest increasing the spatiotemporal distribution of the field dataset. According to RAP, from 1986 to 2023, the site became hotter and drier, bare ground increased, and annual forbs and grasses increased while perennials decreased. RAP products did not agree with field-collected data; however, the trends over time may be useful for informing rangeland management actions.

cattle grazing management↗

DOE OSTI2011

Electromagnetic Isolation Solutions in Low Temperature Cofired Ceramic (LTCC)

Low Temperature Cofired Ceramic (LTCC) is a commercial ceramic-glass multilayer technology with compelling advantages for microelectronics, microsystems and sensors. High frequency applications require good electrical properties such as low dielectric loss and newer applications require extreme isolation from electromagnetic interference (EMI) that is even difficult to measure (-150db). Approaches to providing this isolation, once provided by via fences, have included sidewall coating and full tape thickness features (FTTF) that have been introduced by the filling of slots with via-fill compositions. Several techniques for creating these structures have been modeled for stress and temperature effects in the face of other necessary attachments, such as metallic seal frames. The relative effects of attachment media, FTTF geometry, and alternative measures will be reported. Approaches for thick film and thin film implementations are described.

36 MATERIALS SCIENCE↗

DOE OSTI2014

Results from the DOE Advanced Gas Reactor Fuel Development and Qualification Program

Modular HTGR designs were developed to provide natural safety, which prevents core damage under all design basis accidents and presently envisioned severe accidents. The principle that guides their design concepts is to passively maintain core temperatures below fission product release thresholds under all accident scenarios. This level of fuel performance and fission product retention reduces the radioactive source term by many orders of magnitude and allows potential elimination of the need for evacuation and sheltering beyond a small exclusion area. This level, however, is predicated on exceptionally high fuel fabrication quality and performance under normal operation and accident conditions. Germany produced and demonstrated high quality fuel for their pebble bed HTGRs in the 1980s, but no U.S. manufactured fuel had exhibited equivalent performance prior to the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. The design goal of the modular HTGRs is to allow elimination of an exclusion zone and an emergency planning zone outside the plant boundary fence, typically interpreted as being about 400 meters from the reactor. To achieve this, the reactor design concepts require a level of fuel integrity that is better than that claimed for all prior US manufactured TRISO fuel, by a few orders of magnitude. The improved performance level is about a factor of three better than qualified for German TRISO fuel in the 1980’s. At the start of the AGR program, without a reactor design concept selected, the AGR fuel program selected to qualify fuel to an operating envelope that would bound both pebble bed and prismatic options. This resulted in needing a fuel form that could survive at peak fuel temperatures of 1250°C on a time-averaged basis and high burnups in the range of 150 to 200 GWd/MTHM (metric tons of heavy metal) or 16.4 to 21.8% fissions per initial metal atom (FIMA). Although Germany has demonstrated excellent performance of TRISO-coated UO2 particle fuel up to about 10% FIMA and 1150°C, UO2 fuel is known to have limitations because of CO formation and kernel migration at the high burnups, power densities, temperatures, and temperature gradients that may be encountered in the prismatic modular HTGRs. With uranium oxycarbide (UCO) fuel, the kernel composition is engineered to prevent CO formation and kernel migration, which are key threats to fuel integrity at higher burnups, temperatures, and temperature gradients. Furthermore, the recent poor fuel performance of UO2 TRISO fuel pebbles measured in Chinese irradiation testing in Russia and in German pebbles irradiated at 1250°C, and historic data on poorer fuel performance in safety testing of German pebbles that experienced burnups in excess of 10% FIMA [1] have each raised concern about the use of UO2 TRISO above 10% FIMA and 1150°C and the degree of margin available in the fuel system. This continues to be an active area of study internationally.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2014

Big Explosives Experimental Facility - BEEF

The Big Explosives Experimental Facility or BEEF is a ten acre fenced high explosive testing facility that provides data to support stockpile stewardship and other national security programs. At BEEF conventional high explosives experiments are safely conducted providing sophisticated diagnostics such as high speed optics and x-ray radiography.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Biogenic Aerosols—Effects on Clouds and Climate: Snowfall Experiment Field Campaign Report

The snowfall measurement campaign took place during deployment of the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Climate Research Facility second ARM Mobile Facility (AMF2) in Finland. The campaign focused on understanding snowfall microphysics and characterizing performance of surface-based snowfall measurement instruments. This was achieved by combining triple frequency (X, Ka, W-band) radar observations of vertical structure of the precipitation, microwave radiometer observations of liquid water path (LWP), and lidar measurements of supercooled water layers with surface-based observations of snowfall rate and particle size distributions. To facilitate accurate surface measurements of snowfall properties, a double-fence intercomparison reference wind protection for the weighing precipitation gauge and two-dimensional (2D)-video disdrometer was built on site. Due to the duplication of some instruments, namely the 2D-video disdrometer and the weighing gauge, we were able to characterize their measurement errors as a function of wind speed, thus aiming at providing a correction procedure for the other ARM sites.

snowfall microphysics, snow growth processes, prec↗

DOE OSTI2017

Sensored fiber reinforced polymer grate

Various technologies described herein pertain to a sensored grate that can be utilized for various security fencing applications. The sensored grate includes a grate framework and an embedded optical fiber. The grate framework is formed of a molded polymer such as, for instance, molded fiber reinforced polymer. Further, the grate framework includes a set of elongated elements, where the elongated elements are spaced to define apertures through the grate framework. The optical fiber is embedded in the elongated elements of the grate framework. Moreover, bending or breaking of one or more of the elongated elements can be detected based on a change in a characteristic of input light provided to the optical fiber compared to output light received from the optical fiber.

36 MATERIALS SCIENCE↗

DOE OSTI2017

ABLEPathPlanner library for Umbra

Umbra contains a flexible, modular path planner that is used to simulate complex entity behaviors moving within 3D terrain environments that include buildings, barriers, roads, bridges, fences, and a variety of other terrain features (water, vegetation, slope, etc…). The path planning algorithm is a critical component required to execute these tactical behaviors to provide realistic entity movement and provide efficient system computing performance.

Oppel III, Fred J↗