Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EQUATIONS - STRESSES PLATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Scaling of low-velocity impact for symmetric composite laminates

The equations governing the problem of low-velocity impact of a simply supported rectangular midplane-symmetric laminated plate are nondimensionalized such that the problem is defined in terms of five dimensionless parameters. A parametric study using the Graeco-Latin Factorial Plan is performed. Semi-empirical formulas for maximum impact force, impact duration, and maximum back surface strains are obtained. It is found that some of the simple impact models provide the bounds for the case of impact on a finite extent plate. A one parameter model is derived for impacts of short duration.

Sankar, Bhavani V.↗
NASA NTRS1991

Momentum transfer in the one-dimensional impact of spaced plates

The two-dimensional hydrocode CSQ III was used to calculate the fraction of momentum transferred from a flyer plate to a target of two spaced plates. The effect of the vaporization phase transition, as calculated with the ANEOS analytical complete three-phase equation of state, was estimated. Application of these results to the protection of spacecraft from meteoroids and orbital debris is discussed.

Abbott, R. D.↗
NASA NTRS1997

Modeling of Structural-Acoustic Interaction Using Coupled FE/BE Method and Control of Interior Acoustic Pressure Using Piezoelectric Actuators

A coupled finite element (FE) and boundary element (BE) approach is presented to model full coupled structural/acoustic/piezoelectric systems. The dual reciprocity boundary element method is used so that the natural frequencies and mode shapes of the coupled system can be obtained, and to extend this approach to time dependent problems. The boundary element method is applied to interior acoustic domains, and the results are very accurate when compared with limited exact solutions. Structural-acoustic problems are then analyzed with the coupled finite element/boundary element method, where the finite element method models the structural domain and the boundary element method models the acoustic domain. Results for a system consisting of an isotropic panel and a cubic cavity are in good agreement with exact solutions and experiment data. The response of a composite panel backed cavity is then obtained. The results show that the mass and stiffness of piezoelectric layers have to be considered. The coupled finite element and boundary element equations are transformed into modal coordinates, which is more convenient for transient excitation. Several transient problems are solved based on this formulation. Two control designs, a linear quadratic regulator (LQR) and a feedforward controller, are applied to reduce the acoustic pressure inside the cavity based on the equations in modal coordinates. The results indicate that both controllers can reduce the interior acoustic pressure and the plate deflection.

Mei, Chuh↗
NASA NTRS2000

Validation of a High-Order Prefactored Compact Scheme on Nonlinear Flows with Complex Geometries

Three benchmark problems are solved using a sixth-order prefactored compact scheme employing an explicit 10th-order filter with optimized fourth-order Runge-Kutta time stepping. The problems solved are the following: (1) propagation of sound waves through a transonic nozzle; (2) shock-sound interaction; and (3) single airfoil gust response. In the first two problems, the spatial accuracy of the scheme is tested on a stretched grid, and the effectiveness of boundary conditions is shown. The solution stability and accuracy near a shock discontinuity is shown as well. Also, 1-D nonlinear characteristic boundary conditions will be evaluated. In the third problem, a nonlinear Euler solver will be used that solves the equations in generalized curvilinear coordinates using the chain rule transformation. This work, continuing earlier work on flat-plate cascades and Joukowski airfoils, will focus mainly on the effect of the grid and boundary conditions on the accuracy of the solution. The grids were generated using a commercially available grid generator, GridPro/az3000.

Hixon, Ray↗
NASA NTRS1976

Evaluation of flat-plate collector efficiency under controlled conditions in a solar simulator

The measured thermal efficiencies of 35 collectors tested with a solar simulator, along with the correlation equations used to generalize the data, are presented. The single correlation used is shown to apply to all the different types of collectors tested, including one with black paint and one cover, one with a selective surface coating and two covers, and an evacuated-tube collector. The test and correlation technique is also modified by using a shield so that collectors larger than the simulator test area can also be tested. This technique was verified experimentally for a shielded collector for which the collector shielded area was 31% of the solar simulator radiation area. A table lists all the collectors tested, the collector areas, and the experimental constants used to correlate the data for each collector.

Johnson, S. M.↗
NASA NTRS1976

Evaluation of flat-plate collector efficiency under controlled conditions in a solar simulator

The measured thermal efficiencies of 35 collectors tested with a solar simulator, along with the correlation equations used to generalize the data, are presented in this report. The single correlation used is shown to apply to all the different types of collectors tested, including one with black paint and one cover, one with a selective surface coating and two covers, and an evacuated-tube collector. The test and correlation technique is also modified by using a shield so that collectors larger than the simulator test area can also be tested. This technique was verified experimentally for a shielded collector for which the collector shielded area was 31% of the solar simulator radiation area. A table lists all the collectors tested, the collector areas, and the experimental constants used to correlate the data for each collector.

Johnson, S. M.↗
NASA NTRS1989

Vibration of beams and plate strips with three-dimensional flexibility

Studies making use of higher vibration modes and frequencies have indicated a need for a more accurate beam theory. Equations of motion are developed here that give a more accurate representation of the dynamic behavior of a beam than conventional beam theory. Results are obtained using these equations for the natural vibrations of simply-supported aluminum beams of rectangular cross-sections. These results are compared to results from conventional beam theory, and they are examined to identify where various effects are important.

Stein, Manuel↗
NASA NTRS2016

Transient Growth Analysis of Compressible Boundary Layers with Parabolized Stability Equations

The linear form of parabolized linear stability equations (PSE) is used in a variational approach to extend the previous body of results for the optimal, non-modal disturbance growth in boundary layer flows. This methodology includes the non-parallel effects associated with the spatial development of boundary layer flows. As noted in literature, the optimal initial disturbances correspond to steady counter-rotating stream-wise vortices, which subsequently lead to the formation of stream-wise-elongated structures, i.e., streaks, via a lift-up effect. The parameter space for optimal growth is extended to the hypersonic Mach number regime without any high enthalpy effects, and the effect of wall cooling is studied with particular emphasis on the role of the initial disturbance location and the value of the span-wise wavenumber that leads to the maximum energy growth up to a specified location. Unlike previous predictions that used a basic state obtained from a self-similar solution to the boundary layer equations, mean flow solutions based on the full Navier-Stokes (NS) equations are used in select cases to help account for the viscous-inviscid interaction near the leading edge of the plate and also for the weak shock wave emanating from that region. These differences in the base flow lead to an increasing reduction with Mach number in the magnitude of optimal growth relative to the predictions based on self-similar mean-flow approximation. Finally, the maximum optimal energy gain for the favorable pressure gradient boundary layer near a planar stagnation point is found to be substantially weaker than that in a zero pressure gradient Blasius boundary layer.

Compressible boundary layer↗
NASA NTRS1992

Structural similitude and scaling laws for laminated beam-plates

The establishment of similarity conditions between two structural systems is discussed. Similarity conditions provide the relationship between a scale model and its prototype and can be used to predict the behavior of the prototype by extrapolating the experimental data of the corresponding small-scale model. Since satisfying all the similarity conditions simultaneously is difficult or even impossible, distorted models with partial similarity (with at least one similarity condition relaxed) are more practical. Establishing similarity conditions based on both dimensional analysis and direct use of governing equations is discussed, and the possibility of designing distorted models is investigated. The method is demonstrated through analysis of the cylindrical bending of orthotropic laminated beam-plates subjected to transverse line loads.

Simitses, George J.↗
NASA NTRS1992

Structural similitude and scaling laws for laminated beam-plates

The establishment of similarity conditions between two structural systems is discussed. Similarity conditions provide the relationship between a scale model and its prototype and can be used to predict the behavior of the prototype by extrapolating the experimental data of the corresponding small-scale model. Since satisfying all the similarity conditions simultaneously is difficult or even impossible, distorted models with partial similarity (with at least one similarity condition relaxed) are more practical. Establishing similarity conditions based on both dimensional analysis and direct use of governing equations is discussed, and the possibility of designing distorted models is investigated. The method is demonstrated through analysis of the cylindrical bending of orthotropic laminated beam-plates subjected to transverse line loads.

Simitses, G. J.↗
NASA NTRS2007

Displacement Theories for In-Flight Deformed Shape Predictions of Aerospace Structures

Displacement theories are developed for a variety of structures with the goal of providing real-time shape predictions for aerospace vehicles during flight. These theories are initially developed for a cantilever beam to predict the deformed shapes of the Helios flying wing. The main structural configuration of the Helios wing is a cantilever wing tubular spar subjected to bending, torsion, and combined bending and torsion loading. The displacement equations that are formulated are expressed in terms of strains measured at multiple sensing stations equally spaced on the surface of the wing spar. Displacement theories for other structures, such as tapered cantilever beams, two-point supported beams, wing boxes, and plates also are developed. The accuracy of the displacement theories is successfully validated by finite-element analysis and classical beam theory using input-strains generated by finite-element analysis. The displacement equations and associated strain-sensing system (such as fiber optic sensors) create a powerful means for in-flight deformation monitoring of aerospace structures. This method serves multiple purposes for structural shape sensing, loads monitoring, and structural health monitoring. Ultimately, the calculated displacement data can be visually displayed to the ground-based pilot or used as input to the control system to actively control the shape of structures during flight.

Ko, William L.↗
NASA NTRS1983

Implicit conservative characteristic modeling schemes for the Euler equations - A new approach

An implicit characteristic-modeling solution scheme for the Euler equations is presented. The scheme does not require the governing equations to be written in characteristic variables or the flux terms to be split into positive and negative contributions. For the two-dimensional problem of a shock wave reflecting from a flat plate, this feature and the simple solution algorithm combine to reduce the computational work per mesh point by 40 percent from that required by a standard, central-difference, implicit, solution algorithm. Application of the method to the quasi-one-dimensional nozzle flow equations for subsonic and supersonic flows without shocks shows the method to be well-conditioned for large time steps.

Wornom, S. F.↗
NASA NTRS1986

Non-reflecting boundary conditions for the compressible Navier-Stokes equations

A small perturbation analysis, in the long wavelength regime, is used to obtain the downstream boundary condition for the pressure for the flow over a flat plate. The methodology is extendable to other geometries. Numerical results for high Reynolds number laminar flows show great improvement in convergence rate to steady state as well as the quality of the results.

Abarbanel, S.↗
NASA NTRS1989

Numerical Study of Three-dimensional Spatial Instability of a Supersonic Flat Plate Boundary Layer

The behavior of spatially growing three-dimensional waves in a supersonic boundary layer was studied numerically by solving the complete Navier-Stokes equations. Satisfactory comparison with linear parallel and non-parallel stability theories, and experiment are obtained when a small amplitude inflow disturbance is used. The three-dimensional unsteady Navier-Stokes equations are solved by a finite difference method which is fourth-order and second-order accurate in the convection and viscous terms respectively, and second-order accurate in time. Spanwise periodicity is assumed. The inflow disturbance is composed of eigenfunctions from linear stability theory. By increasing the amplitude of the inflow disturbance, nonlinear effects in the form of a relaxation type oscillation of the time signal of rho(u) are observed.

Maestrello, Lucio↗
NASA NTRS1971

Transient-forced convection film boiling on an isothermal flat plate

An approach for the solution of transient-forced convection film boiling on an isothermal flat plate using the boundary layer model is developed. The similarity variables are used to convert the governing partial differential equations to ordinary ones. The results of numerical solutions of these ordinary equations indicate that the transient process can be classified as one-dimensional conduction, intermediate, and the steady state regions. The time required for the one-dimensional conduction and the time necessary to attain a steady state condition are obtained. The influence of interfacial shear is seen to be negligible while the Prandtl Number and the ratio (C sub p delta T divided by h sub fg times Pr) have major influence. The use of local similarity approximations for the intermediate regime facilitates prediction of complete boundary layer growth. Using the ratio of time at any instant to the steady state time as abscissa, the curves representing the boundary layer growth can be merged into a single mean curve within 5 percent. Further, the analysis shows that the average rate of heat transfer during transient is 50 to 100 percent higher than those at steady state. The average rate of vapor convected away is 10 to 15 percent lower than at steady state while the average rate of accumulation to form the vapor layer is 1 to 14 times larger. Further, the total heat transferred during transient increases and the evaporation decreases for increasing values of C sub p delta T divided by h sub fg times Pr

Nagendra, H. R.↗
NASA NTRS1973

Hematological Viscometry

Concepts and defining equations for the design of a relative velocity blood viscometer are reported. The device consists of two cone and plate chambers, a variable speed drive, and rotational velocity detectors. Two con-plate systems are directly coupled with one system driving the other through the viscous drag transmitted in the test fluid. Angular velocity measurements are processed electronically. A brief description of current viscometer designs is included.

West, D. R.↗