Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

An Investigation of Bluff Body Blockage Corrections Using the NASA/ODU 6-inch MSB

Spheres of different diameters were tested in the NASA/ODU 6-inch MSBS. The objective is to develop an improved understanding of blockage corrections to be made to other bluff-body geometries. Drag coefficients are shown with classical corrections applied, along with wall pressure signatures and base pressure measurements. Anomalous behavior was observed with the largest diameter, thought to be some form of flow breakdown, hence uncorrectable interference.

blunt body↗
NASA NTRS1953

Force and Pressure Recovery Characteristics at Supersonic Speeds of a Conical Spike Inlet with a Bypass Discharging from the Top or Bottom of the Diffuser in an Axial Direction

Force and pressure-recovery characteristics of a nacelle-type conical-spike inlet with a fixed-area bypass located in the top or bottom of the diffuser are presented for flight Mach numbers of 1.6, 1.8, and 2.0 for angles of attack from 0 degrees to 9 degrees. Top or bottom location of the bypass did not have significant effects on diffuser pressure-recovery, bypass mass-flow ratio, or drag coefficient over the range of angles of attack, flight Mach numbers, and stable engine mass-flow ratios investigated. A larger stable subcritical operating range was obtained with the bypass on the bottom at angles of attack from 3 degrees to 9 degrees at a flight Mach number of 2.0. At a flight Mach number of 2.0, the discharge of 14 percent of the critical mass flow of the inlet by means of a bypass increased the drag only one-fifth of the additive drag that would result for equivalent spillage behind an inlet normal shock without significant reductions in diffuser pressure recovery.

DIFFUSERS, SUBSONIC↗
NASA NTRS1934

The Drag of Two Streamline Bodies as Affected by Protuberances and Appendages

This report presents the results of wind tunnel tests of two airship models conducted to determine the drag coefficients at zero pitch, and the effect of fins and cars and of flat and streamlined protuberances located at various positions along the hull. During the investigation the stern of one model was rounded off to produce a blunter shape. The extreme range of the Reynolds number based on the over-all length of the models was from 1,300,000 to 33,000,000. At large values of the Reynolds number the streamlined protuberance affected the drag very little, and the additional drag caused by the flat protuberance was less than the calculated drag by the protuberance alone. The fins and cars together increased the bare-hull drag about 20 per cent.

Abbott, Ira H↗
NASA NTRS1968

Flight Test of a 40-Foot Nominal Diameter Disk-Gap-Band Parachute Deployed at a Mach Number of 2.72 and a Dynamic Pressure of 9.7 Pounds per Square Foot

A 40-foot-nominal-diameter (12.2 meter) disk-gap-band parachute was flight tested as part of the NASA Supersonic Planetary Entry Decelerator (SPED-I) Program. The test parachute was deployed from an instrumented payload by means of a deployment mortar when the payload was at an altitude of 158,500 feet (48.2 kilometers), a Mach number of 2.72, and a free-stream dynamic pressure of 9.7 pounds per foot(exp 2) (465 newtons per meter(exp 2)). Suspension line stretch occurred 0.46 second after mortar firing and the resulting snatch force loading was -8.lg. The maximum acceleration experienced by the payload due to parachute opening was -27.2g at 0.50 second after the snatch force peak for a total elapsed time from mortar firing of 0.96 second. Canopy-shape variations occurred during the higher Mach number portion of the flight test (M greater than 1.4) and the payload was subjected to large amplitude oscillatory loads. A calculated average nominal axial-force coefficient ranged from about 0.25 immediately after the first canopy opening to about 0.50 as the canopy attained a steady inflated shape. One gore of the test parachute was damaged when the deployment bag with mortar lid passed through it from behind approximately 2 seconds after deployment was initiated. Although the canopy damage caused by the deployment bag penetration had no apparent effect on the functional capability of the test parachute, it may have affected parachute performance since the average effective drag coefficient of 0.48 was 9 percent less than that of a previously tested parachute of the same configuration.

EXPERIMENTS↗
NASA NTRS1987

Two-phase flow measurements of a spray in a turbulent flow

The dynamics of spray drop interaction with a turbulent coflowing air stream were investigated using a Phase Doppler Particle Analyzer that determines both drop size and velocity. Detailed measurements obtained included spray drop size, axial and radial velocity, angle of trajectory, drop Reynolds number, and size-velocity correlations. The gas-phase flow field was also ascertained via the behavior of the smallest drops. Also investigated were the drag coefficients of droplets in a turbulent air cross flow for both monodispersions and polydispersions. Most notable aspects of the coflow included the effect of air streams with velocities significantly different from the spray sheet. Local changes in number density were produced as a result of lateral convection and streamwise accelerations and decelerations of various drop size classes. The complexity of the spray field interaction illustrated by this data effectively describes the development of the spray due to the influence of the airflow. The droplet drag measurements showed similar behavior for monodispersed and polydispersed flows and similar trends to previously obtained data. The measurements also pointed out further studies which would assist in creating an improved drag law for polydispersed drops in a turbulent environment.

Rudoff, R. C.↗
NASA NTRS2013

Testing Small CPAS Parachutes Using HIVAS

The High Velocity Airflow System (HIVAS) facility at the Naval Air Warfare Center (NAWC) at China Lake was successfully used as an alternative to flight test to determine parachute drag performance of two small Capsule Parachute Assembly System (CPAS) canopies. A similar parachute with known performance was also tested as a control. Realtime computations of drag coefficient were unrealistically low. This is because HIVAS produces a non-uniform flow which rapidly decays from a high central core flow. Additional calibration runs were performed to characterize this flow assuming radial symmetry from the centerline. The flow field was used to post-process effective flow velocities at each throttle setting and parachute diameter using the definition of the momentum flux factor. Because one parachute had significant oscillations, additional calculations were required to estimate the projected flow at off-axis angles. The resulting drag data from HIVAS compared favorably to previously estimated parachute performance based on scaled data from analogous CPAS parachutes. The data will improve drag area distributions in the next version of the CPAS Model Memo.

Ray, Eric S.↗
NASA NTRS2022

An ODE-Fitting Approach to Estimate Critical Aircraft Performance Parameters for Trajectory Prediction

Ground-based decision support tools (DST) in air traffic management (ATM) typically perform trajectory prediction based on aircraft performance model (APM) parameters, but some or all of these parameters might not be readily available. In particular, the three critical parameters required for trajectory prediction are the thrust setting, drag coefficients, and takeoff weight of the aircraft. Unfortunately, these parameters are coupled and appear together in physics-based kinetic models. Past approaches utilize data from a specific phase of flight (climb, level flight or descent), where one or more of the parameters are assumed to be known and estimate the remaining unknown parameters. This approach introduces bias/errors and also does not extend to scenarios where all of the above parameters are not known with sufficient accuracy. This paper is the first of its kind to propose a generalized framework for simultaneous estimation of all three critical APM parameters (thrust, drag, and mass). The proposed approach utilizes data from both the climb and descent phases and fits the ordinary differential equation for altitude in each phase using historical trajectory data available from radar tracks or ADS-B. The approach yields a set of optimized APM parameters that are best suited to fit each historical flight record. The methodology is applied on on sample flights from three different aircraft types, and the results demonstrate low fit error and consequently will yield a high level of prediction accuracy.

trajectory prediction, aircraft performance model,↗
NASA NTRSDate not supplied

An ODE-Fitting Approach to Estimate Critical Aircraft Performance Parameters for Trajectory Prediction

Ground-based decision support tools (DST) in air traffic management (ATM) typically perform trajectory prediction based on aircraft performance model (APM) parameters, but some or all of these parameters might not be readily available. In particular, the three critical parameters required for trajectory prediction are the thrust setting, drag coefficients, and takeoff weight of the aircraft. Unfortunately, these parameters are coupled and appear together in physics-based kinetic models. Past approaches utilize data from a specific phase of flight (climb, level flight or descent), where one or more of the parameters are assumed to be known and estimate the remaining unknown parameters. This approach introduces bias/errors and also does not extend to scenarios where all of the above parameters are not known with sufficient accuracy. This paper is the first of its kind to propose a generalized framework for simultaneous estimation of all three critical APM parameters (thrust, drag, and mass). The proposed approach utilizes data from both the climb and descent phases and fits the ordinary differential equation for altitude in each phase using historical trajectory data available from radar tracks or ADS-B. The approach yields a set of optimized APM parameters that are best suited to fit each historical flight record. The methodology is applied on on sample flights from three different aircraft types, and the results demonstrate low fit error and consequently will yield a high level of prediction accuracy.

trajectory prediction↗
NASA NTRS1951

Flight Investigation of the Drag of Round-nosed Bodies of Revolution at Mach Numbers from 0.6 to 1.5 Using Rocket-propelled Test Vehicles

Values of total drag coefficient were measured for four round-nosed bodies of revolution in free flight at Mach numbers from 0.6 to 1.5 and Reynolds numbers from 10 x 10(6) to 50 x 10(6). The bodies were designed by rounding off the sharp, fineness-ratio-3.56 nose of a previously tested configuration. The nose radii tested were 27.4, 38.7, 80.6, and 100 percent of the maximum body radius and corresponded to values of 0.075, 0.150, 0.650, and 1.000, respectively, for the ratio of nose-sphere frontal area to body frontal area. The body having least bluntness did not differ appreciably in drag from the pointed-nose body. The others showed marked increases in supersonic drag with increasing bluntness. (author)

Hart, Roger G↗
NASA NTRS1959

Stability Investigation of a Blunted Cone and a Blunted Ogive with a Flared Cylinder Afterbody at Mach Numbers from 0.30 to 2.85

A cone with a blunt nose tip and a 10.7 deg cone half angle and an ogive with a blunt nose tip and a 20 deg flared cylinder afterbody have been tested in free flight over a Mach number range of 0.30 to 2.85 and a Reynolds number range of 1 x 10(exp 6) to 23 x 10(exp 6). Time histories, cross plots of force and moment coefficients, and plots of the longitudinal force,coefficient, rolling velocity, aerodynamic center, normal- force-curve slope, and dynamic stability are presented. With the center-of-gravity location at about 50 percent of the model length, the models were both statically and dynamically stable throughout the Mach number range. For the cone, the average aerodynamic center moved slightly forward with decreasing speeds and the normal-force-curve slope was fairly constant throughout the speed range. For the ogive, the average aerodynamic center remained practically constant and the normal-force-curve slope remained practically constant to a Mach number of approximately 1.6 where a rising trend is noted. Maximum drag coefficient for the cone, with reference to the base area, was approximately 0.6, and for the ogive, with reference to the area of the cylindrical portion, was approximately 2.1.

Coltrane, Lucille C.↗
NASA NTRS2018

Generation of Performance Model for the Aeolian Wind Tunnel (AWT) Rotor at Reduced Pressure

The NASA Jet Propulsion Laboratory (JPL) designed the Mars Helicopter (MH) in collaboration with AeroVironment Inc., NASA Ames Research Center, and NASA Langley Research Center to explore the possibility of a vertical takeoff and landing (VTOL) Unmanned Aerial Vehicle (UAV) for flight on Mars. A 40-inch-diameter Aeolian Wind Tunnel (AWT) rotor, roughly approximating the proposed MH design by JPL, was tested in forward flight at Mars atmospheric pressure at the NASA Ames Planetary Aeolian Laboratory (PAL) in support of MH research efforts. This report describes the generation of the rotor model used to correlate with that experimental effort as reported by Ament and Koning. The 40-inch-diameter rotor was 3D-scanned and transformed into an airfoil deck. The scanned rotor airfoil sections are analyzed using C81 Generator (C81Gen) to generate the sectional aerodynamic coefficients for comprehensive analyses. A mid-fidelity computational fluid dynamics (CFD) simulation using Rotorcraft CFD (RotCFD) is pursued to efficiently estimate rotor hover and forward flight performance. Simulations at two pressures, 7 mbar (approximate Martian atmospheric pressure) and 1018 mbar (1 atmosphere), are performed to gain an understanding of the performance differences and Reynolds number effects observed. Experimental 1-atmosphere thrust for single- and dual-rotor isolated hover cases correlate well with the modeled rotor. Performance results at reduced pressure (7 mbar) show a drastic decrease in lift for equivalent RPMs tested at 1 atmosphere. Although this is primarily due to pressure reduction, Reynolds number effects also contribute to this decrease, as airfoil lift and drag coefficients are affected when compared with 1-atmosphere results. Further, simulated rotor power coefficient shows drastic increases at reduced pressures, attributed to laminar boundary layer separation, as described in Koning et al. for the MH rotor analysis. PAL experimental Martian Surface Wind Tunnel (MARSWIT) results are presented in the paper by Ament and Koning. The very low Reynolds number range is currently not well understood and presents various challenges for both experimentation and simulation.

Koning, Witold J. F.↗
NASA NTRS1956

Flat Plate Cascades at Supersonic Speed

A brief review of exact two-dimensional supersonic flow theory and Ackeret's linearized theory are first presented. The lift and drag coefficients of a cascade of flat plates are calculated exactly and compared to those obtained using the linearized theory. The forces on the cascade are determined for unsteady inlet flow. The flat plate cascade theory is extended to compute the efficiency of a supersonic propeller with friction and finite blade thickness.

FLOW - PLATES, FLAT - SUPERSONIC↗
NASA NTRS2019

Adjoint-Based Anisotropic Mesh Adaptation for a Stabilized Finite-Element Flow Solver

An adjoint solver is implemented in the FUN3D stabilized finite-element flow solver. The adjoint solution is used to generate anisotropic, adapted meshes to control error in scalar out- put functionals, such as lift or drag coefficient. The inviscid and turbulent adjoints are verified with a finite-difference derivative approximation and can be used in design optimization in addition to mesh adaptation. The adjoint capability represents an extension of previous research using the FUN3D stabilized finite-element capability with metric-based mesh adaptation and interpolation-based error estimates to generate highly anisotropic adapted meshes for turbulent flows. In the present work, a metric-based approach is again utilized, where the adjoint and the primal solutions both contribute to the generation of a metric tensor field that is subsequently used to produce the required anisotropic mesh for each adaptation cycle. Adaptive results are then shown for an inviscid supersonic flow over a diamond airfoil, inviscid transonic flow over the ONERA M6 wing, and viscous laminar flow over the NACA 0012 airfoil, all using drag force as the output functional. Adjoint-based adaptation is compared with a multiscale solution-based approach that controls the L norm of Mach number interpolation error to demonstrate the effectiveness and effciency of the adjoint-based adaptive mesh technology.

Balan, Aravind↗
NASA NTRS2010

Development of an Uncertainty Model for the National Transonic Facility

This paper introduces an uncertainty model being developed for the National Transonic Facility (NTF). The model uses a Monte Carlo technique to propagate standard uncertainties of measured values through the NTF data reduction equations to calculate the combined uncertainties of the key aerodynamic force and moment coefficients and freestream properties. The uncertainty propagation approach to assessing data variability is compared with ongoing data quality assessment activities at the NTF, notably check standard testing using statistical process control (SPC) techniques. It is shown that the two approaches are complementary and both are necessary tools for data quality assessment and improvement activities. The SPC approach is the final arbiter of variability in a facility. Its result encompasses variation due to people, processes, test equipment, and test article. The uncertainty propagation approach is limited mainly to the data reduction process. However, it is useful because it helps to assess the causes of variability seen in the data and consequently provides a basis for improvement. For example, it is shown that Mach number random uncertainty is dominated by static pressure variation over most of the dynamic pressure range tested. However, the random uncertainty in the drag coefficient is generally dominated by axial and normal force uncertainty with much less contribution from freestream conditions.

Walter, Joel A.↗
NASA NTRS2011

Effects of Low Activity Solar Cycle on Orbital Debris Lifetime

Long duration of low solar activity in the last solar minimum has an undesirable consequence of extending the lifetime of orbital debris. The AFRL TacSat-2 satellite decommissioned in 2008 has finally re-entered into the atmosphere on February 5th after more than one year overdue. Concerning its demise we have monitored its orbital decay and monthly forecasted Tacsat-2 re-entry since September 2010 by using the Orbital Element Prediction (OEP) model developed by the AFRL Orbital Drag Environment program. The model combines estimates of future solar activity with neutral density models, drag coefficient models, and an orbit propagator to predict satellite lifetime. We run the OEP model with solar indices forecast by the NASA Marshall Solar Activity Future Estimation model, and neutral density forecast by the MSIS-00 neutral density model. Based on the two line elements in 2010 up to mid September, we estimated at a 50% confidence level TacSat-2's re-entry time to be in early February 2011, which turned out to be in good agreement with Tacsat-2's actual re-entry date. The potential space weather effects of the coming low activity solar cycle on satellite lifetime and orbital debris population are examined. The NASA long-term orbital debris evolutionary model, LEGEND, is used to quantify the effects of solar flux on the orbital debris population in the 200-600 km altitude environment. The results are discussed for developing satellite orbital drag application product.

Cable, Samual B.↗
NASA NTRS2002

Spike-Nosed Bodies and Forward Injected Jets in Supersonic Flow

The paper contains new numerical simulation and experimental test results of blunt body drag reduction using thin spikes mounted in front of a body and one- or two-phase jets injected against a supersonic flow. Numerical simulations utilizing the NASA CFL3D code were conducted at the Hampton University Fluid Mechanics and Acoustics Laboratory (FM&AL) and experimental tests were conducted using the facilities of the IM/MSU Aeromechanics and Gas Dynamics Laboratory. Previous results were presented at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference. Those results were based on some experimental and numerical simulation tests for supersonic flow around spike-nosed or shell-nosed bodies, and numerical simulations were conducted only for a single spike-nosed or shell-nosed body at zero attack angle, alpha=0. In this paper, experimental test results of gas, liquid and solid particle jet injection against a supersonic flow are presented. In addition, numerical simulation results for supersonic flow around a multiple spike-nosed body with non-zero attack angles and with a gas and solid particle forward jet injection are included. Aerodynamic coefficients: drag, C(sub D), lift, C(sub L), and longitudinal momentum, M(sub z), obtained by numerical simulation and experimental tests are compared and show good agreement.

Gilinsky, M.↗
NASA NTRS2002

Spike-Nosed Bodies and Forward Injected Jets in Supersonic Flow

The paper contains new numerical simulation and experimental test results of blunt body drag reduction using thin spikes mounted in front of a body and one- or two-phase jets injected against a supersonic flow. Numerical simulations utilizing the NASA CFL3D code were conducted at the Hampton University Fluid Mechanics and Acoustics Laboratory (FM&AL) and experimental tests were conducted using the facilities of the IM/MSU Aeromechanics and Gas Dynamics Laboratory. Previous results were presented at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference. Those results were based on some experimental and numerical simulation tests for supersonic flow around spike-nosed or shell-nosed bodies, and numerical simulations were conducted only for a single spike-nosed or shell-nosed body at zero attack angle, alpha = 0 degrees. In this paper, experimental test results of gas, liquid and solid particle jet injection against a supersonic flow are presented. In addition, numerical simulation results for supersonic flow around a multiple spike-nosed body with non-zero attack angles and with a gas and solid particle forward jet injection are included. Aerodynamic coefficients: drag, C (sub D), lift, C(sub L), and longitudinal momentum, M(sub z), obtained by numerical simulation and experimental tests are compared and show good agreement.

Gilinsky, M.↗
NASA NTRS1963

Spin Investigation Of A 1/20-Scale Model Of An Unswept-Wing, Twin-Engine, Observation Airplane

An investigation was conducted in the Langley 20-foot free-spinning tunnel on a 1/20-scale model of an unswept-wing, twin-engine, observation airplane. The effects of control settings and movements on the erect spin and recovery characteristics for the normal loading and the most rearward center-of-gravity loading (external wing tanks full) were determined. Also, tests were made to determine the effect on the spin and recovery characteristics of a large radar store, of empty and full external wing tanks, and of an asymmetrical condition when one empty or one full external wing tank is carried. Spin-recovery parachute tests were also performed. The results of the tests indicate that erect spins obtained on the airplane for the normal loading should be satisfactorily terminated by rudder reversal to full against the spin, ailerons moved to with the spin, followed one-half turn later by forward movement of the stick to neutral. With the radar store, with wing tanks empty, or with an asymmetrical condition when one empty tank is on either wing, satisfactory recoveries can be obtained by using the same technique as for the normal loading. Recoveries for the model with a rearward center-of-gravity loading (external wing tanks full) or with a full tank on the wing inboard of the spin axis will be slow to unsatisfactory with rudder reversal to full against the spin followed by brisk forward stick movement. With a full tank on the wing outboard of the spin axis, the recoveries will be satisfactory. Spins in the landing configuration should be terminated by first retracting the flaps, slats, and landing gear, after which recovery should be attempted immediately by using the recovery technique recommended for the normal loading condition. Inverted spins can be satisfactorily terminated by rudder reversal to full against the spin followed by neutralization of the longitudinal and lateral controls. A 12.7-foot-diameter tail parachute with a towline length of 21.7 feet and a drag coefficient of 0.65 should be satisfactory for recoveries from erect and inverted demonstration spins when used simultaneously with movement of rudder to neutral.

SPIN↗