Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Doppler”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Extreme measurements with Photonic Doppler Velocimetry (PDV)

Photonic Doppler Velocimetry (PDV) is a fiber-based diagnostic for the extreme conditions created by high-speed impact, explosive detonation, electrical pulsed power, and intense laser ablation. PDV is a conceptually simple application of the optical Doppler effect, but measurements above 1 km/s only became practical at the beginning of the twenty-first century. In this work, I discuss the evolution of PDV, its operational details, practical analysis, and outstanding challenges.

47 OTHER INSTRUMENTATION↗

Time-lens photon Doppler velocimetry (TL-PDV)

Here, we describe a time lens (TL) to expand the dynamic range of photon Doppler velocimetry (PDV) systems. The principle and preliminary design of a TL-PDV system are explained and shown to be feasible through simulations. In a PDV system, an interferometer is used for measuring frequency shifts due to the Doppler effect from the target motion. However, the sampling rate of the electronics could limit the velocity range of a PDV system. A four-wave-mixing (FWM) TL applies a quadratic temporal phase to an optical signal within a nonlinear FWM medium (such as an integrated photonic waveguide or a highly nonlinear optical fiber). By spectrally isolating the mixing product, termed the idler, and with appropriate lengths of dispersion prior to and after this FWM TL, a temporally magnified version of the input signal is generated. Therefore, the frequency shifts of PDV can be “slowed down” with the magnification factor M of the TL. M = 1 corresponds to a regular PDV system without a TL. M = 10 has been shown to be feasible for a TL-PDV system. The use of this effect for PDV can expand the velocity measurement range and allow for the use of lower bandwidth electronics. TL-PDV will open up new avenues for various dynamic material experiments.

47 OTHER INSTRUMENTATION↗

Quantum interference of biphotons with a Doppler frequency shift

We report a theoretical study of transformation of a biphoton state of light under Bragg diffraction on a travelling sound wave in an acousto-optic modulator (AOM). It is shown that the diffraction of AOM biphotons emitted during the collinear parametric scattering of light leads to a shift of the carrier frequency of a biphoton wave packet, which exceeds twice the Doppler frequency shift for the classical field. A method is proposed for measuring the Doppler frequency shift of a biphoton, which is based on interference between independent biphotons. (quantum interferometry)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

ON THE DOPPLER SHIFT AND ASYMMETRY OF STOKES PROFILES OF PHOTOSPHERIC Fe I AND CHROMOSPHERIC Mg I LINES

We analyzed the full Stokes spectra using simultaneous measurements of the photospheric (Fe I 630.15 and 630.25 nm) and chromospheric (Mg I b {sub 2} 517.27 nm) lines. The data were obtained with the High Altitude Observatory/National Solar Observatory (HAO/NSO) advanced Stokes polarimeter, about a near disk center sunspot region, NOAA AR 9661. We compare the characteristics of the Stokes profiles in terms of Doppler shifts and asymmetries among the three spectral lines, helping us to better understand the chromospheric lines and the magnetic and flow fields in different magnetic regions. The main results are: (1) for the penumbral area observed by the photospheric Fe I lines, Doppler velocities derived from Stokes I ({nu} {sub i}) are very close to those derived from linear polarization profiles ({nu}{sub lp}) but significantly different from those derived from Stokes V profiles ({nu}{sub zc}), thus providing direct and strong evidence that the penumbral Evershed flows are magnetized and mainly carried by the horizontal magnetic component; (2) the rudimentary inverse Evershed effect observed by the Mg I b {sub 2} line provides qualitative evidence on its formation height that is around or just above the temperature minimum region; (3) {nu}{sub zc} and {nu}{sub lp} in the penumbrae and {nu}{sub zc} in the pores generally approach their {nu} {sub i} observed by the chromospheric Mg I line, which is not the case for the photospheric Fe I lines; (4) the outer penumbrae and pores show similar Stokes V asymmetry behavior that tend to change from positive values in the photosphere (Fe I lines) to negative values in the low chromosphere (Mg I line); (5) the Stokes V profiles in plage regions are highly asymmetric in the photosphere and more symmetric in the low chromosphere; and (6) strong redshifts and large asymmetries are found around the magnetic polarity inversion line within the common penumbra of the {delta} spot. We offer explanations or speculations to the observed discrepancies between the photospheric and chromospheric lines in terms of the three-dimensional structure of the magnetic and velocity fields. This study thus emphasizes the importance of spectropolarimetry using chromospheric lines.

79 ASTRONOMY AND ASTROPHYSICS↗

SOLAR MERIDIONAL CIRCULATION FROM DOPPLER SHIFTS OF THE Fe I LINE AT 5250 A AS MEASURED BY THE 150-FOOT SOLAR TOWER TELESCOPE AT THE MT. WILSON OBSERVATORY

Doppler shifts of the Fe I spectral line at 5250 A from the full solar disk obtained over the period 1986 to 2009 are analyzed to determine the circulation velocity of the solar surface along meridional planes. Simultaneous measurements of the Zeeman splitting of this line are used to obtain measurements of the solar magnetic field that are used to select low field points and impose corrections for the magnetically induced Doppler shift. The data utilized is from a new reduction that preserves the full spatial resolution of the original observations so that the circulation flow can be followed to latitudes of 80{sup 0} N/S. The deduced meridional flow is shown to differ from the circulation velocities derived from magnetic pattern movements. A reversed circulation pattern is seen in polar regions for three successive solar minima. A surge in circulation velocity at low latitudes is seen during the rising phases of cycles 22 and 23.

79 ASTRONOMY AND ASTROPHYSICS↗

A high-frequency Doppler feature in the power spectra of simulated GRMHD black hole accretion disks

Black hole binaries exhibit a wide range of variability phenomena, from large-scale state changes to broadband noise and quasi-periodic oscillations, but the physical nature of much of this variability is poorly understood. We examine the variability properties of three GRMHD simulations of thin accretion disks around black holes of varying spin, producing light curves and power spectra as would be seen by observers. We find that the simulated power spectra show a broad feature at high frequency, which increases in amplitude with the inclination of the observer. We show that this high-frequency feature is a product of the Doppler effect and that its location is a function of the mass and spin of the black hole. This Doppler feature demonstrates that power spectral properties of the accretion disk can be tied to, and potentially used to determine, physical properties of the black hole.

79 ASTRONOMY AND ASTROPHYSICS↗

A misaligned prograde orbit for Kepler-13 Ab via doppler tomography

Transiting planets around rapidly rotating stars are not amenable to precise radial velocity observations, such as are used for planet candidate validation, as they have wide, rotationally broadened stellar lines. Such planets can, however, be observed using Doppler tomography, wherein stellar absorption line profile distortions during transit are spectroscopically resolved. This allows the validation of transiting planet candidates and the measurement of the stellar spin-planetary orbit (mis)alignment, which is an important statistical probe of planetary migration processes. We present Doppler tomographic observations that provide direct confirmation of the hot Jupiter Kepler-13 Ab and also show that the planet has a prograde, misaligned orbit with λ = 58.°6 ± 2.°0. Our measured value of the spin-orbit misalignment is in significant disagreement with the value of λ = 23° ± 4° previously measured by Barnes et al. (2011) from the gravity-darkened Kepler light curve. We also place an upper limit of 0.75 M{sub ☉} (95% confidence) on the mass of Kepler-13 C, the spectroscopic companion to Kepler-13 B, which is the proper-motion companion of the planet host star Kepler-13 A.

79 ASTRONOMY AND ASTROPHYSICS↗

Long-range Doppler lidar measurements of wind turbine wakes and their interaction with turbulent atmospheric boundary-layer flow at Perdigao 2017

As part of the Perdigão 2017 campaign, vertical RHI (range-height indicator) scans with long-range pulsed Doppler wind lidars were performed aligned with the main wind direction and a wind turbine (WT) located on a mountain ridge. The measurements are used to not only retrieve flow velocities, but also their variance and - by using the turbulent broadening of the Doppler spectrum - also turbulent kinetic energy (TKE) dissipation rate. The study shows that turbulence in the WT wake is dependent on the turbulence of the inflow, but also on atmospheric stability. In stable atmospheric conditions, wakes could be analyzed up to five rotor diameters downstream (D) and showed the maximum turbulence in the wake at 2-3 D, whereas in unstable conditions, the maximum was found at 2 D and the wake could not be detected further than 3 D. A clear dependency of wake turbulence enhancement on inflow turbulence intensity is found, which levels out to no further enhancement at turbulence intensities of 30%.

17 WIND ENERGY↗

Comparison of horizontal wind speed and direction measurements from dual-Doppler radar and profiling lidars

Dual-Doppler radar is a relatively new technology in the wind energy community and thus not yet studied vastly. This paper aims to compare horizontal wind speed and direction data retrieved from dual-Doppler radar and profiling lidars within the American WAKE experimeNt (AWAKEN) to investigate the influence of measurement height, wind direction and speed on the comparison. The 10-min averaged data show a better agreement of the measurements for higher altitudes, especially at faster wind speeds. For the wind direction, two sectors of larger differences in the measurements were detected: around 270° transient winds occur with a higher frequency than in other sectors. To explain the different measurement values in the wind direction sector around 90°, further studies, e.g. on the influence of atmospheric stability, are necessary.

17 WIND ENERGY↗

Cavity ring-down spectroscopy measurements of sub-Doppler hyperfine structure

Frequency-stabilized cavity ring-down spectroscopy (FS-CRDS) was used to measure magnetic dipole transitions in the b {sup 1{Sigma}}{sub g}{sup +} (leftarrow) X {sup 3{Sigma}}{sub g}{sup -}(0,0) band of O{sub 2}. The {sup 17}O-containing isotopologues show unresolved hyperfine structure due to magnetic hyperfine splitting in the ground state. The sensitivity and stability of FS-CRDS allow for quantitative sub-Doppler measurements of the hyperfine constants, even when the hyperfine splittings are much smaller than the Doppler width. Unlike saturation spectroscopy, this linear absorption technique can be applied to weak transitions and employed to quantitatively measure intensities and line shapes. This method may be an attractive approach for measuring unresolved hyperfine structure in excited electronic states.

74 ATOMIC AND MOLECULAR PHYSICS↗

Prospects for Doppler cooling of three-electronic-level molecules

Analogous to the extension of laser cooling techniques from two-level to three-level atoms, Doppler cooling of molecules with an intermediate electronic state is considered. In particular, we use a rate-equation approach to simulate cooling of SiO{sup +}, in which population buildup in the intermediate state is prevented by its short lifetime. We determine that Doppler cooling of SiO{sup +} can be accomplished without optically repumping from the intermediate state, at the cost of causing undesirable parity flips and rotational diffusion. Since the necessary repumping would require a large number of continuous-wave lasers, optical pulse shaping of a femtosecond laser is proposed as an attractive alternative. Other candidate three-electron-level molecules are also discussed.

74 ATOMIC AND MOLECULAR PHYSICS↗

Doppler cooling with coherent trains of laser pulses and a tunable velocity comb

We explore the possibility of decelerating and Doppler cooling an ensemble of two-level atoms by a coherent train of short, nonoverlapping laser pulses. We derive analytical expressions for mechanical force exerted by the train. In frequency space the force pattern reflects the underlying frequency comb structure. The pattern depends strongly on the ratio of the atomic lifetime to the repetition time between the pulses and pulse area. For example, in the limit of short lifetimes, the frequency-space peaks of the optical force wash out. We propose to tune the carrier-envelope offset frequency to follow the Doppler-shifted detuning as atoms decelerate; this leads to compression of atomic velocity distribution about comb teeth and results in a ''velocity comb''--a series of narrow equidistant peaks in the velocity space.

74 ATOMIC AND MOLECULAR PHYSICS↗

Observation of Doppler-free electromagnetically induced transparency in atoms selected optically with specific velocity

We observed an electromagnetically induced transparency signal in a four-level system with optically selected rubidium atoms at specific velocities in a room-temperature vaporized cell. Since the atoms behave like cold atoms in the selected atomic view, the observed signals coincide with a trapped atomic system. According to this result, we can observe Doppler-free signals, which correspond from 1.2 to 1.0 K in a Doppler-broadened medium. And the selected atoms have velocity components of {+-}(131 {+-} 3) MHz per wave number. Our experimental results can provide insight for research in cold media.

74 ATOMIC AND MOLECULAR PHYSICS↗

Doppler- and recoil-free laser excitation of Rydberg states via three-photon transitions

Three-photon laser excitation of Rydberg states by three different laser beams can be arranged in a starlike geometry that simultaneously eliminates the recoil effect and Doppler broadening. Our analytical and numerical calculations for a particular laser excitation scheme 5S{sub 1/2}{yields}5P{sub 3/2}{yields}6S{sub 1/2}{yields}nP in Rb atoms have shown that, compared to the one- and two-photon laser excitation, this approach provides much narrower linewidth and longer coherence time for both cold atom samples and hot vapors, if the intermediate one-photon resonances of the three-photon transition are detuned by more than respective single-photon Doppler widths. This method can be used to improve fidelity of Rydberg quantum gates and precision of spectroscopic measurements in Rydberg atoms.

74 ATOMIC AND MOLECULAR PHYSICS↗

Time delay and Doppler tests of the Lorentz symmetry of gravity

Modifications to the classic time-delay effect and Doppler shift in general relativity (GR) are studied in the context of the Lorentz-violating standard-model extension (SME). We derive the leading Lorentz-violating corrections to the time-delay and Doppler shift signals, for a light ray passing near a massive body. It is demonstrated that anisotropic coefficients for Lorentz violation control a time-dependent behavior of these signals that is qualitatively different from the conventional case in GR. Estimates of sensitivities to gravity-sector coefficients in the SME are given for current and future experiments, including the recent Cassini solar conjunction experiment.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Photonic Doppler Velocimetry Probe Designed with Stereo Imaging

The velocity distribution of an imploding curved surface is measured with a miniature fiber-optic probe. The probe uses fiber matrix arrays that are focused onto different regions of this curved surface. A pyramid reflector deflects the interrogation onto specific regions of this curved surface. The fiber arrays record velocity along several hundred lines of sight with sub-nanosecond resolution. Reflected light from each spot on the moving surface is Doppler shifted with a small portion of this light propagating backwards through the launching fiber. The reflected light is mixed with a reference laser in a technique called Photonic Doppler velocimetry, providing continuous time records. Within the probe, seven groups of miniature optical relay lenses are grouped into a close-packed array, allowing the interrogation of seven regions of interest. A six-faceted pyramid reflector with a conical hole drilled into its center is used to direct the light beams onto different regions. To minimize back reflections, the fiber matrix arrays are index matched onto the first relay lens made of fused silica. The optical lens design minimizes the laser beam diameters and also provides excellent imaging capabilities. Therefore, two of the fiber matrix arrays are replaced by coherent bundles for stereo imaging recorded by a high-speed framing camera. This requires additional cutouts of the pyramid reflector to allow imaging overlap. Six additional 1.5 mm diameter incoherent bundles are attached to the edges of the pyramid reflector and are used for illumination. Precision metrology on the direction cosines of the trajectories is measured to satisfy environmental requirements for vibration and temperature.

photonic doppler velocimetry, PDV, pyramid reflect↗

Design, Assembly, and Testing of a Photon Doppler Velocimetry Probe

A novel fiber-optic probe measures the velocity distribution of an imploding surface along many lines of sight. Reflected light from each spot on the moving surface is Doppler shifted with a small portion of this light propagating backwards through the launching fiber. The reflected light is mixed with a reference laser in a technique called photon Doppler velocimetry, providing continuous time records. Within the probe, a matrix array of 56 single-mode fibers sends light through an optical relay consisting of three types of lenses. Seven sets of these relay lenses are grouped into a close-packed array allowing the interrogation of seven regions of interest. A six-faceted prism with a hole drilled into its center directs the light beams to the different regions. Several types of relay lens systems have been evaluated, including doublets and molded aspheric singlets. The optical design minimizes beam diameters and also provides excellent imaging capabilities. One of the fiber matrix arrays can be replaced by an imaging coherent bundle. This close-packed array of seven relay systems provides up to 476 beam trajectories. The pyramid prism has its six facets polished at two different angles that will vary the density of surface point coverage. Fibers in the matrix arrays are angle polished at 8{sup o} to minimize back reflections. This causes the minimum beam waist to vary along different trajectories. Precision metrology on the direction cosine trajectories is measured to satisfy environmental requirements for vibration and temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Fisheye Lens as a Photonic Doppler Velocimetry Probe

A new fisheye lens design is used as a miniature probe to measure the velocity distribution of an imploding surface along many lines of sight. Laser light, directed and scattered back along each beam on the surface, is Doppler shifted by the moving surface and collected into the launching fiber. The received light is mixed with reference laser light in each optical fiber in a technique called photonic Doppler velocimetry, providing a continuous time record. An array of single-mode optical fibers sends laser light through the fisheye lens. The lens consists of an index-matching positive element, two positive doublet groups, and two negative singlet elements. The optical design minimizes beam diameters, physical size, and back reflections for excellent signal collection. The fiber array projected through the fisheye lens provides many measurement points of surface coverage over a hemisphere with very little crosstalk. The probe measures surface movement with only a small encroachment into the center of the cavity. The fiber array is coupled to the index-matching element using index-matching gel. The array is bonded and sealed into a blast tube for ease of assembly and focusing. This configuration also allows the fiber array to be flat polished at a common object plane. In areas where increased measurement point density is desired, the fibers can be close packed. To further increase surface density coverage, smaller-diameter cladding optical fibers may be used.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗