Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dendrites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Analysis of defect structure in silicon. Silicon sheet growth development for the large area silicon sheet task of the Low-Cost Solar array Project

One hundred ninety-three silicon sheet samples, approximately 880 square centimeters, were analyzed for twin boundary density, dislocation pit density, and grain boundary length. One hundred fifteen of these samples were manufactured by a heat exchanger method, thirty-eight by edge defined film fed growth, twenty-three by the silicon on ceramics process, and ten by the dendritic web process. Seven solar cells were also step-etched to determine the internal defect distribution on these samples. Procedures were developed or the quantitative characterization of structural defects such as dislocation pits, precipitates, twin & grain boundaries using a QTM 720 quantitative image analyzing system interfaced with a PDP 11/03 mini computer. Characterization of the grain boundary length per unit area for polycrystalline samples was done by using the intercept method on an Olympus HBM Microscope.

Natesh, R.↗
NASA NTRS1982

Irradiation effects in rapidly and conventionally solidified alloys. Phase stability in rapidly solidified N i-Nb under Ni ion irradiation

Two alloy compositions in the Ni-Nb system (Ni60Nb40 and Ni85Nb15) were produced by rapidly quenching from the melt with the piston anvil technique. The Ni60Nb40 was transformed to a metastable, partially crystalline state by heat treatment in a differential scanning calorimeter. The Ni85Nb15 was fully crystalline, with the majority of the grains composed of collections of primary dendrite arms. Both compositions were irradiated with 4 MeV Ni++ ions. The irradiation induced microstructures were examined by transmission electron microscopy and compared with thermally aged samples. The thermal evolution was arrested by ion irradiation in the temperature range studied, by inhibiting the nucleation of the NiNb phase. No irradiation induced voids were observed. It is found that the ion irradiation drives the microstructure along a different path than thermal evolution.

Source record↗
NASA NTRS1982

A Module Experimental Process System Development Unit (MEPSDU)

Restructuring research objectives from a technical readiness demonstration program to an investigation of high risk, high payoff activities associated with producing photovoltaic modules using non-CZ sheet material is reported. Deletion of the module frame in favor of a frameless design, and modification in cell series parallel electrical interconnect configuration are reviewed. A baseline process sequence was identified for the fabrication of modules using the selected dendritic web sheet material, and economic evaluations of the sequence were completed.

Source record↗
NASA NTRS1982

Inexpensive cross-linked polymeric separators made from water-soluble polymers

Polyvinyl alcohol (PVA), cross-linked chemically with aldehyde reagents, produces membranes which demonstrate oxidation resistance, dimensional stability, low ionic resistivity (less than 0.8 Ohms sq cm), low zincate diffusivity (less than 1 x 10 to the -7th mols/sq cm per min), and low zinc dendrite penetration rate (greater than 350 min) which make them suitable for use as alkaline battery separators. They are intrinsically low in cost, and environmental health and safety problems associated with commercial production appear minimal. Preparation, property measurements, and cell test results in Ni/Zn and Ag/Zn cells are described and discussed.

Hsu, L.-C.↗
NASA NTRS1981

Progress toward goals in silicon sheet development

One of the goals of the national photovoltaic program in the U.S. is the establishment of an industry producing photovoltaic material which can be sold at a price not exceeding $0.70/W by 1986. A key element concerning the achievement of this goal is the development and utilization of improved methods for producing silicon sheet. Specific technologies being investigated in this connection can be divided into two categories. Methods of one category are based on a utilization of sheet growth techniques including film-fed growth, dendritic web, and silicon-on-ceramic processes. The approaches used by methods of the second category involve ingot and wafering processes, including Czochralski growth, the heat exchanger method, multiblade procedures, and the use of a fixed abrasive multiwire. It is found that using $84/kg silicon, most sheet technologies would yield module prices in the $2.00/Wp to $3.00/Wp range.

Koliwad, K. M.↗
NASA NTRS1982

Conditions of formation of pyroxene excentroradial chondrules

Understanding the exact mechanism of origin of chondrules and the attendant physical conditions remains a key factor in understanding the early evolution of the solar system. The present investigation is concerned with an interpretation of the range of cooling histories needed to make chondrules. Chondrule-like spherules were formed in dynamic crystallization experiments, using gas-mixing facilities. It is found that textures in pyroxene-rich chondrules are well reproduced in the laboratory by cooling melts of chondrule composition from just above the liquidus. The range of pyroxene dendrite widths is slightly greater for natural chondrules than for droplets cooled from 50 C/hr to greater than 3000 C/hr. A blanketing medium of variable thickness explains the cooling rates lower than expected for radiative cooling. Experimental results, textures indicating incomplete melting, and isotopic disequilibrium are compatible with reheating of primitive material in the early solar nebula.

Hewins, R. H.↗
NASA NTRS1984

Oscillating-Crucible Technique for Silicon Growth

Technique yields better mixing of impurities and superior qualiity crystals. Accellerated motion stirs melt which reduces temperature gradients and decreases boundary layer for diffusion of impurities near growing surface. Results better mixing of impurities into melt, decrease in tendency for dendritic growth or cellular growth and crystals with low dislocation density. Applied with success to solution growth and Czochralski growth, resulting in large crystals of superior quality.

Daud, T.↗
NASA NTRS1984

Improved Radiative Control of Ribbon Growth

Shield modifications enhance growth rate while reducing silicon oxide formation. Control of dendritic-web crystal growth requires precise control of web temperature profile. Achieved by using series of thermal radiation shields to control thermal-radiation field in region where melt solidifying onto crystal ribbon being pulled from melt.

Mchugh, J. P.↗
NASA NTRS1982

Theoretical Model of the Effect of Crack Tip Blunting on the Ultimate Tensile Strength of Welds in 2219-T87 Aluminum

A theoretical model representing blunting of a crack tip radius through diffusion of vacancies is presented. The model serves as the basis for a computer program which calculates changes, due to successive weld heat passes, in the ultimate tensile strength of 2219-T81 aluminum. In order for the model to yield changes of the same order in the ultimate tensile strength as that observed experimentally, a crack tip radius of the order of .001 microns is required. Such sharp cracks could arise in the fusion zone of a weld from shrinkage cavities or decohered phase boundaries between dendrites and the eutectic phase, or, possibly, from plastic deformation due to thermal stresses encountered during the welding process. Microstructural observations up to X2000 (resolution of about .1 micron) did not, in the fusion zone, show structural details which changed significantly under the influence of a heat pass, with the exception of possible small changes in the configuration of the interdendritic eutectic and in porosity build-up in the remelt zone.

Beil, R. J.↗
NASA NTRS1982

Process research on non-CZ silicon material

High risk, high payoff research areas associated with he process for producing photovoltaic modules using non-CZ sheet material are investigated. All investigations are being performed using dendritic web silicon, but all processes are directly applicable to other ribbon forms of sheet material. The technical feasibility of forming front and back junctions in non-CZ silicon using liquid dopant techniques was determined. Numerous commercially available liquid phosphorus and boron dopant solutions are investigated. Temperature-time profiles to achieve N(+) and P(+) sheet resistivities of 60 + or - 10 and 40 + or - s10 ohms per square centimeter respectively are established. A study of the optimal method of liquid dopant application is performed. The technical feasibility of forming a liquid applied diffusion mask to replace the more costly chemical vapor deposited SiO2 diffusion mask was also determined.

Source record↗
NASA NTRS1983

Method of increasing minority carrier lifetime in silicon web or the like

A silicon dendrite is grown as a ribbon forming two silicon crystal layers which are separated by an interface layer which contains a large number of defects. Significant increase of minority carrier lifetime with homogeneous distribution at the outer surfaces of the two silicon crystal layers is achieved by processing the web in an atmosphere of a selected gas, e.g., oxygen, nitrogen or an inert gas, for about 30 minutes to several hours at a temperature preferably on the order of 900 to 1200 C.

Liu, J. K.↗
NASA NTRS1982

Gravitationally induced convection during directional solidification of off-eutectic Mn-Bi alloys

The effects of thermal and solute gradient, gravity induced convection during vertical directional solidification, on longitudinal macrosegregation of Bi and Mn rich off-eutectic starting compositions, has been studied as a function of composition, growth velocity and gravity vector orientation. Since the morphology of these alloys is characterized by an aligned, rodlike permanent magnet composite when grown cooperatively, the magnetic properties were used to measure composition segregation and the transition from dendritic to composite growth. Severe macrosegregation was observed in all cases studied and the degree of convection inferred by modeling the observed composition segregation using a stagnant film approach. Morphological stability was found to follow a constitutional supercooling-type law for both Bi and Mn rich compositions.

Pirich, R. G.↗
NASA NTRS1983

Materials processing in the reduced-gravity environment of space

Studies of the effects of gravitation on the behavior of fluids and the shapes of materials for the years 1977-1982 are reviewed, with a focus on ground-based research which complements and gives direction to experimentation in the reduced-gravity environment of space. Fluid-behavior topics discussed include crystal growth from melts and from vapor, dendritic solidification and casting, multiphase alloy solidification, electrophoresis, convection behavior, and special heat-flow considerations characteristic of the space environment. With regard to solids, such subjects as containerless positioning technology and its applications (in glass preparation, liquid drop and shell studies, nucleation experiments, and measurements of fundamental properties of molten reactants), liquid floating zones, solid self-deformation, and sedimentation and buoyancy effects are considered and illustrated.

Carruthers, J. R.↗
NASA NTRS1985

Improved Melt-Level Control System

Laser feedback control automatically maintains silicon melt levels. During long-term growth of dendritic-web silicon, silicon melt level controlled and held nearly constant using laser feedback system to sense level of melt and control silicon-pellet feed rate.

Meier, D. L.↗
NASA NTRS1983

Solidification rate influence on orientation and mechanical properties of MAR-M-246+Hf

The influence of solidification rates on the orientation and mechanical properties of MAR-M-246+Hf was studied. The preferred orientation was found to be (001) for single crystals, with all samples with 45 degrees of (001). Tensile tests were performed at room temperature. The anisotropy of directionally solidified MAR-M-246+Hf was demonstrated by gage section deformation. Dendrite arm spacing and crystal growth were found to depend on solidification rates and source material conditions. The greatest strength occurred at lower solidification rates. Some single crystals were grown by control of growth rates without seeding.

Hamilton, D.↗
NASA NTRS1984

Crystallization of Silicon Ribbons

Purity constraints for reasonable solar-cell efficiency require that silicon-ribbon growth for photovoltaics occur in a regime in which constitutional supercooling or other compositional effects on the crystallization front are not important. A major consideration in the fundamentals of crystallization is the removal of the latent heat of fusion. The direction of removal, compared with the growth direction, has a major influence on the crystallization rate and the development of localized stresses. The detailed shape of the crystallization front appears to have two forms: that required for dendritic-web growth, and that occurring in all others. After the removal of the latent heat of fusion, the thermal-mechanical behavior of all ribbons appears similar within the constraints of the exothermal gradient. The technological constraints in achieving the required thermal and mechanical conditions vary widely among the growth processes.

Leipold, M. H.↗