Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Wind-tunnel investigation on the effect of a crescent planform on drag

Lift and drag forces were compared for elliptic and crescent wing models at cruise and climb conditions in the NASA/Langley 14 x 22-ft subsonic tunnel. The force measurements were obtained for an angle-of-attack range from -3 to 10 deg at a Reynolds number of about 1.7 million. The results indicate that for attached flow conditions, the crescent wing with its highly swept tips generates less lift-dependent drag than the elliptic wing for given lift force, wing span, and freestream conditions. The drag reduction is thought to be the result of the favorable influence of trailing wake deformations on the pressure distribution of the highly swept outboard region of the crescent wing.

Van Dam, C. P.↗
NASA NTRS1996

Effect of Cavity Injection on Wall Drag in a Supersonic Flow with Reflecting Shocks

The wall drag test tunnel at NASA Langley Research Center was used to evaluate simulated scramjet fuel injection into a wall cavity. In this tunnel, one wall consists of interchangeable aluminum plates attached to an air bearing suspension system. The plates were equipped with load cells to measure drag forces and static taps to determine pressure distributions. The plates were exposed to a Mach 2 air stream at a total pressure of 115 psia (793 kPa). This flow field contained a train of weak unsteady, reflecting shock waves that were produced in the nozzle assembly located upstream of the test section.

Castiglone, L. A.↗
NASA NTRS1938

The Effect of Surface Irregularities on Wing Drag. II - Lap Joints: Lap Joints - 2

Tests have been made in the NACA 8-foot high-speed wind tunnel of the drag caused by four types of lap joint. The tests were made on an airfoil of NACA 23012 section and 5-foot chord and covered in a range of speeds from 80 to 500 miles per hour and lift coefficients from 0 to 0.30. The increases in profile drag caused by representative arrangements of laps varied from 4 to 9%. When there were protruding rivet heads on the surface, the addition of laps increased the drag only slightly. Laps on the forward part of a wing increased the drag considerably more than those farther back.

Hood, Manley J.↗
NASA NTRS1938

The Effect of Surface Irregularities on Wing Drag: Roughness - 3

Tests have been made in the N.A.C.A. 8-foot high-speed wind tunnel of the drag caused by roughness on the surface of an airfoil of N.A.C.A. 23012 section and 5-foot chord. The tests were made at speeds from 80 t o 500 miles per hour at lift coefficients from 0 to 0.30. For conditions corresponding to high-speed flight, the increase in the drag was 30 percent of the profile drag of the smooth airfoil for the roughness produced by spray painting and 63 percent for the roughness produced. by 0.0037-inch carborundum grains. About one-half the drag increase was caused by the roughness on the forward one-fourth of the airfoil. Sandpapering the painted surface with No. 400 sandpaper made it sufficiently smooth that the drag was no greater than when the surface was polished. In the lower part of the range investigated the drag due to roughness increased rapidly with Reynolds Number.

Hood, Manley J.↗
NASA NTRS1983

Axisymmetric bluff-body drag reduction using circumferential grooves

The effect of shoulder radiusing and circumferentially grooving the afterbodies of bluff bodies to reduce the base drag at low speeds is discussed. Shoulder radii as large as 2.75 body diameters are examined. Reynolds number based on body diameter varied from 20,000 to 200,000. Results indicate that increasing the shoulder radius to 2.75 body diameters can reduce the drag levels to those of a streamline body having 67 percent greater fineness ratio. For zero shoulder radius, circumferential grooves were found to be effective in reducing body drag for zero shoulder radius in both laminar and tripped flow. Circumferential grooves on the afterbody with a shoulder radius of one-half the body diameter were only effective in reducing drag for laminar flow.

Howard, F. G.↗
NASA NTRS1991

Nonlinear Aerodynamics and the Design of Wing Tips

The analysis and design of wing tips for fixed wing and rotary wing aircraft still remains part art, part science. Although the design of airfoil sections and basic planform geometry is well developed, the tip regions require more detailed consideration. This is important because of the strong impact of wing tip flow on wing drag; although the tip region constitutes a small portion of the wing, its effect on the drag can be significant. The induced drag of a wing is, for a given lift and speed, inversely proportional to the square of the wing span. Concepts are proposed as a means of reducing drag. Modern computational methods provide a tool for studying these issues in greater detail. The purpose of the current research program is to improve the understanding of the fundamental issues involved in the design of wing tips and to develop the range of computational and experimental tools needed for further study of these ideas.

Kroo, Ilan↗
NASA NTRS2017

The Effectiveness of Shrouding on Reducing Meshed Spur Gear Power Loss Test Results

Gearbox efficiency is reduced at high rotational speeds due to windage drag and viscous effects on rotating, meshed gear components. A goal of NASA aeronautics rotorcraft research is aimed at propulsion technologies that improve efficiency while minimizing vehicle weight. Specifically, reducing power losses to rotorcraft gearboxes would allow gains in areas such as vehicle payload, range, mission type, and fuel consumption. To that end, a gear windage rig has been commissioned at NASA Glenn Research Center to measure windage drag on gears and to test methodologies to mitigate windage power losses. One method used in rotorcraft gearbox design attempts to reduce gear windage power loss by utilizing close clearance walls to enclose the gears in both the axial and radial directions. The close clearance shrouds result in reduced drag on the gear teeth and reduced power loss. For meshed spur gears, the shrouding takes the form of metal side plates and circumferential metal sectors. Variably positioned axial and radial shrouds are incorporated in the NASA rig to study the effect of shroud clearance on gearbox power loss. A number of researchers have given experimental and analytical results for single spur gears, with and without shrouding. Shrouded meshed spur gear test results are sparse in the literature. Windage tests were run at NASA Glenn using meshed spur gears at four shroud configurations: unshrouded, shrouded (max. axial, max. radial), and two intermediate shrouding conditions. Results are compared to available meshed spur gear power loss data analyses as well as single spur gear data analyses.

windage↗