Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Liquid-Cooled Heat Sink Optimization for Thermal Imbalance Mitigation in Wide-Bandgap Power Modules

Power semiconductor die placement on substrates used in high-power modules is generally optimized to minimize electrical parasitic (e.g., stray inductance, common-mode capacitance), taking into account the minimum spacing between semiconductor dies for thermal decoupling. The layout assumes sufficient heat spreading and transfer from dies to the cooling structure. Insulated metal substrate-based power module designs may lead to asymmetrical thermal resistance across the dies, which may cause significant temperature differences among the devices. Such unintentional thermal asymmetries can lead to oversizing the cooling system design or underusing the semiconductor power processing capability. This article proposes a thermal imbalance mitigation method that uses evolutionary optimized liquid-cooled heat sinks to improve the thermal loading among devices.

42 ENGINEERING↗

SU-E-J-65: Evaluation of a Radiation-Induced Cell Proliferation Probability Formula Using Monte Carlo Simulation

Purpose: To evaluate the analytic formula of the cell death probability after single fraction dose. Methods: Cancer cells endlessly divide, but radiation causes the cancer cells to die. Not all cells die right away after irradiation. Instead, they continue dividing for next few cell cycles before they stop dividing and die. At the end of every cell cycle, the cell decides if it undertakes the mitotic process with a certain probability, Pdiv, which is altered by the radiation. Previously, by using a simple analytic model of radiobiology experiments, we obtained a formula of Pdeath (= 1 − Pdiv). A question is if the proposed probability can reproduce the well-known survival data of the LQ model. In this study, we evaluated the formula by doing a Monte Carlo simulation of the cell proliferation process. Starting with Ns seed cells, the cell proliferation process was simulated for N generations or until all cells die. We counted the number of living cells at the end. Assuming that the cell colony survived when more than Nc cells were still alive, the surviving fraction S was estimated. We compared the S vs. dose, or S-D curve, with the LQ model. Results: The results indicated that our formula does not reproduce the experimentally observed S-D curve without selecting appropriate α and α/β. With parameter optimization, there was a fair agreement between the MC result and the LQ curve of dose lower than 20Gy. However, the survival fraction of MC decreased much faster in comparison to the LQ data for doses higher than 20 Gy. Conclusion: This study showed that the previously derived probability of cell death per cell cycle is not sufficiently accurate to replicate common radiobiological experiments. The formula must be modified by considering its cell cycle dependence and some other unknown effects.

60 APPLIED LIFE SCIENCES↗

Adrian Portales Coop Internship Report

Using the thesis of W.R. Nolan (cite) as a guide, Cobalt Iron (CoFe) powders were reacted with 0.1 wt.% and 0.2 wt.% phosphoric acid in a 20:1 ratio of acetone to phosphoric acid. The powders were then dried at room temperature. The resulting phosphate coated CoFe was then mixed with 0.75 wt.% of the lubricant N,N' ethylene bis-stearamide (trade name: Acrawax C) and hot pressed to form a consolidated soft magnetic material referred to as CoFeP. With an avenue of synthesis for CoFeP determined, a proper amount of stock was synthesized for continuous “brick” production. While under current optimization, these 1x1 mm magnetic bricks will ultimately be placed and secured along the inside wall of each MK Magnetics transformer core by an appropriate CoFeP dispersed epoxy. As of now each brick has been produced though a pressing and annealing process via square 2x2 cm die. Before a brick is made a pressure calculation is run to ensure the dies maximum operating pressure is not exceeded. Figure 1. ensures the user’s safety by showing that the tons-on-ram required for a 2x2 cm square die to reach 760 MPa is below the point of die failure.

36 MATERIALS SCIENCE↗

Fine Pitch Bonding for High Density Interconnects

CTE (coefficient of thermal expansion) mismatch between two wafers has potential for brittle failure when large areas are bonded on top of one another (wafer to wafer or wafer to die bonds). To address this type of failure, we proposed patterning a polymer around metallic interconnects. For this project, utilized benzo cyclobutene (BCB) to form the bond and accommodate stress. For the metal interconnects, we used indium. To determine the benefits of utilizing BCB, mechanical shear testing of die bonding with just BCB were compared to die bonded just with oxide. These tests demonstrated that BCB, when cured for only 30 minutes and bonded at 200°C, the BCB was able to withstand shear forces similar to oxide. Furthermore, when the BCB did fail, it experienced a more ductile failure, allowing the silicon to crack, rather than shatter. To demonstrate the feasibility of using BCB between indium interconnects, wafers were pattered with layers of BCB with vias for indium or ENEPIG (electroless nickel, electroless palladium, immersion gold). Subsequently, these wafers were pattered with a variety of indium or ENEPIG interconnect pitches, diameters, and heights. These dies were bonded under a variety of conditions, and those that held a bond, were cross-sectioned and imaged. Images revealed that certain bonding conditions allow for interconnects and BCB to achieve a void-less bond and thus demonstrate that utilizing polymers in place of oxide is a feasible way to reduce CTE stress.

36 MATERIALS SCIENCE↗

Force Modulator System

Many metal parts manufacturers use large metal presses to shape sheet metal into finished products like car body parts, jet wing and fuselage surfaces, etc. These metal presses take sheet metal and - with enormous force - reshape the metal into a fully formed part in a manner of seconds. Although highly efficient, the forces involved in forming metal parts also damage the press itself, limit the metals used in part production, slow press operations and, when not properly controlled, cause the manufacture of large volumes of defective metal parts. To date, the metal-forming industry has not been able to develop a metal-holding technology that allows full control of press forces during the part forming process. This is of particular importance in the automotive lightweighting efforts under way in the US automotive manufacturing marketplace. Metalforming Controls Technology Inc. (MC2) has developed a patented press control system called the Force Modulator that has the ability to control these press forces, allowing a breakthrough in stamping process control. The technology includes a series of hydraulic cylinders that provide controlled tonnage at all points in the forming process. At the same time, the unique cylinder design allows for the generation of very high levels of clamping forces (very high tonnages) in very small spaces; a requirement for forming medium and large panels out of HSS and AHSS. Successful production application of these systems testing at multiple stamping operations - including Ford and Chrysler - has validated the capabilities and economic benefits of the system. Although this technology has been adopted in a number of stamping operations, one of the primary barriers to faster adoption and application of this technology in HSS projects is system cost. The cost issue has surfaced because the systems currently in use are built for each individual die as a custom application, thus driving higher tooling costs. This project proposed to better marry the die-specific Force Modulator technology with stamping presses in the form of a press cushion. This system would be designed to operate the binder ring for multiple parts, thus cutting the per-die cost of the technology. This study reports the results of technology field application. This project produced the following conclusions: (1) The Force Modulator system is capable of operating at very high tempos in the stamping environment; (2) The company can generate substantial, controlled holding tonnage (binder ring pressure) necessary to hold high strength steel parts for proper formation during draw operations; (3) A single system can be designed to operate with a family of parts, thus significantly reducing the per-die cost of a FM system; (4) High strength steel parts made with these systems appear to show significant quality improvements; (5) The amounts of steel required to make these parts is typically less than the amounts required with traditional blank-holding technologies; and (6) This technology will aid in the use of higher strength steels in auto and truck production, thus reducing weight and improving fuel efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Precision metal molding

Method provides precise alignment for metal-forming dies while permitting minimal thermal expansion without die warpage or cavity space restriction. The interfacing dowel bars and die side facings are arranged so the dies are restrained in one orthogonal angle and permitted to thermally expand in the opposite orthogonal angle.

Townhill, A.↗

Silicon ribbon growth by a capillary action shaping technique

The crystal growth method described is a capillary action shaping technique. Meniscus shaping for the desired ribbon geometry occurs at the vertex of a wettable die. As ribbon growth depletes the melt meniscus, capillary action supplies replacement material. A capillary die is so designed that the bounding edges of the die top are not parallel or concentric with the growing ribbon. The new dies allow a higher melt meniscus with concomitant improvements in surface smoothness and freedom from SiC surface particles, which can degrade perfection.

Schwuttke, G. H.↗

Adjustable Tooling for Bending Brake

Deep metal boxes and other parts easily fabricated. Adjustable tooling jig for bending brake accommodates spacing blocks and either standard male press-brake die or bar die. Holds spacer blocks, press-brake die, bar window die, or combination of three. Typical bending operations include bending of cut metal sheet into box and bending of metal strip into bracket with multiple inward 90 degree bends. By increasing free space available for bending sheet-metal parts jig makes it easier to fabricate such items as deep metal boxes or brackets with right-angle bends.

Ellis, J. M.↗

NASA Ultra-Sensitive Miniature Accelerometer

Using micro-machined silicon technology, an ultra-sensitive miniature acce.,rometer can be constructed which meets the requirements for microgravity experiments in the space environment.Such an accelerometer will have a full scale sensitivity of 1C2 g a resolution of lC8 g, low cross axis sensitivity, and low temperature sensitivity. Mass of the device is approximately five grams and its footprint is 2 cm x 2 cm. Innovative features of the accelerometer, which are patented, are: electrostatic caging to withstand handling shock up to 150 g, in-situ calibration, in situ performance characterization, and both static and dynamic compensation. The transducer operates on a force balance principle wherein the displacement of the proof mass is monitored by measuring tunneling electron current flow between a conductive tip, and a fixed platen. The four major parts of the accelerometer are tip die, incorporating the tunneling tip and four field plates for controlling pitch and roll of the proof mass; two proof mass dies, attached to the surrounding frame by sets of four leg" springs; and a force plate die. The four parts are fuse-bonded into a complete assembly. External electrical connections are made at bond pads on the front surface of the force plate die. Materials and processes used in the construction of the transducer are compatible with volume production.

Zavracky, Paul M.↗

Qualification and Reliability for MEMS and IC Packages

Advanced IC electronic packages are moving toward miniaturization from two key different approaches, front and back-end processes, each with their own challenges. Successful use of more of the back-end process front-end, e.g. microelectromechanical systems (MEMS) Wafer Level Package (WLP), enable reducing size and cost. Use of direct flip chip die is the most efficient approach if and when the issues of know good die and board/assembly are resolved. Wafer level package solve the issue of known good die by enabling package test, but it has its own limitation, e.g., the I/O limitation, additional cost, and reliability. From the back-end approach, system-in-a-package (SIAP/SIP) development is a response to an increasing demand for package and die integration of different functions into one unit to reduce size and cost and improve functionality. MEMS add another challenging dimension to electronic packaging since they include moving mechanical elements. Conventional qualification and reliability need to be modified and expanded in most cases in order to detect new unknown failures. This paper will review four standards that already released or being developed that specifically address the issues on qualification and reliability of assembled packages. Exposures to thermal cycles, monotonic bend test, mechanical shock and drop are covered in these specifications. Finally, mechanical and thermal cycle qualification data generated for MEMS accelerometer will be presented. The MEMS was an element of an inertial measurement unit (IMU) qualified for NASA Mars Exploration Rovers (MERs), Spirit and Opportunity that successfully is currently roaring the Martian surface

inertial measurement unit↗

Advanced Flip Chips in Extreme Temperature Environments

The use of underfill materials is necessary with flip-chip interconnect technology to redistribute stresses due to mismatching coefficients of thermal expansion (CTEs) between dissimilar materials in the overall assembly. Underfills are formulated using organic polymers and possibly inorganic filler materials. There are a few ways to apply the underfills with flip-chip technology. Traditional capillary-flow underfill materials now possess high flow speed and reduced time to cure, but they still require additional processing steps beyond the typical surface-mount technology (SMT) assembly process. Studies were conducted using underfills in a temperature range of -190 to 85 C, which resulted in an increase of reliability by one to two orders of magnitude. Thermal shock of the flip-chip test articles was designed to induce failures at the interconnect sites (-40 to 100 C). The study on the reliability of flip chips using underfills in the extreme temperature region is of significant value for space applications. This technology is considered as an enabling technology for future space missions. Flip-chip interconnect technology is an advanced electrical interconnection approach where the silicon die or chip is electrically connected, face down, to the substrate by reflowing solder bumps on area-array metallized terminals on the die to matching footprints of solder-wettable pads on the chosen substrate. This advanced flip-chip interconnect technology will significantly improve the performance of high-speed systems, productivity enhancement over manual wire bonding, self-alignment during die joining, low lead inductances, and reduced need for attachment of precious metals. The use of commercially developed no-flow fluxing underfills provides a means of reducing the processing steps employed in the traditional capillary flow methods to enhance SMT compatibility. Reliability of flip chips may be significantly increased by matching/tailoring the CTEs of the substrate material and the silicon die or chip, and also the underfill materials. Advanced packaging interconnects technology such as flip-chip interconnect test boards have been subjected to various extreme temperature ranges that cover military specifications and extreme Mars and asteroid environments. The eventual goal of each process step and the entire process is to produce components with 100 percent interconnect and satisfy the reliability requirements. Underfill materials, in general, may possibly meet demanding end use requirements such as low warpage, low stress, fine pitch, high reliability, and high adhesion.

Ramesham, Rajeshuni↗

Nuclear Thermal Rocket (NTR) Development Risk Communication

There are clear advantages of development of a Nuclear Thermal Rocket (NTR) for a crewed mission to Mars. NTR for in-space propulsion enables more ambitious space missions by providing high thrust at high specific impulse (approximately 900 sec) that is 2 times the best theoretical performance possible for chemical rockets. Missions can be optimized for maximum payload capability to take more payload with reduced total mass to orbit; saving cost on reduction of the number of launch vehicles needed. Or missions can be optimized to minimize trip time significantly to reduce the deep space radiation exposure to the crew. NTR propulsion technology is a game changer for space exploration. However, "NUCLEAR" is a word that is feared and vilified by some groups and the hostility towards development of any nuclear systems can meet great opposition by the public as well as from national leaders and people in authority. Communication of nuclear safety will be critical to the success of the development of the NTR. Why is there a fear of nuclear? A bomb that can level a city is a scary weapon. The first and only times the Nuclear Bomb was used in a war was on Hiroshima and Nagasaki during World War 2. The "Little Boy" atomic bomb was dropped on Hiroshima on August 6, 1945 and the "Fat Man" on Nagasaki 3 days later on August 9th. Within the first 4 months of bombings, 90- 166 thousand people died in Hiroshima and 60-80 thousand died in Nagasaki. It is important to note for comparison that over 500 thousand people died and 5 million made homeless due to strategic bombing (approximately 150 thousand tons) of Japanese cities and war assets with conventional non-nuclear weapons between 1942- 1945. A major bombing campaign of "firebombing" of Tokyo called "Operation Meetinghouse" on March 9 and 10 consisting of 334 B-29's dropped approximately1,700 tons of bombs around 16 square mile area and over 100 thousand people have been estimated to have died. The declaration of death is very clear for conventional weapons and then the declaration of death due to radiation becomes vague and unclear. This may have been due to people mis-understanding the dangers and effects of radiation when assessing the damage and harm to people initially, but it is also become insidious when expressing opposition to nuclear energy. A nuclear radiation accident can be scary due to the power involved and the fear of radiation release. The International Atomic Energy Agency defines a nuclear and radiation accident a "an event that has led to significant consequences to people, the environment or the facility." There have been 3 commercial nuclear reactor accidents (Chernobyl, Three Mile Island, and Fukushima) that stand out to the public and much of the information about the result and impact to workers, environment, and public can be misleading. Often information is presented without clear correlation with radiation and other pertinent information is left out presenting a very scary situation to affect the emotions of the reader. A very boring but "critically acclaimed" movie was made in 1979 called "The China Syndrome" starring Jane Fonda and Jack Lemmon. The film was released on March 16, 1979, 12 days before the 3-Mile Island nuclear accident in Pennsylvania. The basis from the movie was from a few nuclear plant incidents and in particular, the Brown's Ferry Alabama Power Plant fire. In one scene from the movie, a physicist Dr. Elliott Lowell played by Donald Hotton states that a China Syndrome event would make "an area the size of Pennsylvania" permanently uninhabitable. Real serious nuclear incidents like Chernobyl and Fukushima are often sited to make people fear the consequences of using nuclear power. However, the consequences are at best poorly communicated and at worst fictitiously inflated to instigate social unrest against nuclear power. There is an article being circulated on Facebook with a title "28 Signs that the (US) West Coast is being absolutely fried with nuclear radiation from Fukushima" which focus on mis-information and fear mongering. Nuclear power and NTR are powerful resources that can open many doors for future prosperity and capability. With great power comes great responsibility. Radiation and its effects need to be better understood, quantified, and communicated. A human mission to mars has its own risks of deep space radiation and is considered a considerable risk at 400 milli-Sieverts per year in deep space and 245 milli-Sieverts per year on the surface of Mars as measured by the Mars Curiosity mission. Although these quantities of ionizing radiation are within the astronaut career limit, it exceeds the yearly average amounts of ionizing radiation. Astronaut crews have experienced these levels of radiation before, but for durations shorter than a year, and a mission to Mars could possibly be 3 years in length. There is also evidence that people can comfortably handle higher levels of ionizing radiation where the radiation occurs naturally like Ramsar, Iran when people can experience 270 milli-Sieverts per year. A risk posture that the development, test, and flight of an NTR will meet opposition from groups who oppose nuclear energy must be likely and the impact can be sever to the effort. Active risk mitigation must be taken for an NTR full-scale development project. The NTR design must take into account safety for transport and off nominal conditions. Nuclear fuel element must consider containment of fission products and Low Enriched Uranium (LEU) that may meet less opposition should be considered for safety and security reasons. Even though testing was conducted on Rover/NERVA safely and successfully in the 60's with exhaust sent heavenward in to open air, modern testing of NTR must consider full containment and no release of ionizing radiation to the public and must meet the current requirement of no more than 0.1 milli-Sieverts per year to the public. 0.1 milli-Sieverts is equivalent to eating one banana or a 20 hour plane flight. Good communication with the public and regulatory agencies will be essential to show that all effort is applied toward protection to the public and astronauts. The inspiring endeavor to put humans on Mars to study the planet, search for life, and learn more about this Solar System will be full of risks but it will be worth it. NTR will be worth the development effort if it allows humans to explore our Solar System.

Kim, Tony↗

Power module packaging with double sided planar interconnection and heat exchangers

A double sided cooled power module package having a single phase leg topology includes two IGBT and two diode semiconductor dies. Each IGBT die is spaced apart from a diode semiconductor die, forming a switch unit. Two switch units are placed in a planar face-up and face-down configuration. A pair of DBC or other insulated metallic substrates is affixed to each side of the planar phase leg semiconductor dies to form a sandwich structure. Attachment layers are disposed on outer surfaces of the substrates and two heat exchangers are affixed to the substrates by rigid bond layers. The heat exchangers, made of copper or aluminum, have passages for carrying coolant. The power package is manufactured in a two-step assembly and heating process where direct bonds are formed for all bond layers by soldering, sintering, solid diffusion bonding or transient liquid diffusion bonding, with a specially designed jig and fixture.

33 ADVANCED PROPULSION SYSTEMS↗

High voltage power chip module

A power die module using a compression connection to a power die in a small package with corona extenders positioned around short efficient path exterior electrical connections. The module is built from a baseplate with connected sidewalls forming an interior compartment holding a power substrate with attached threaded inserts. A printed circuit board bolted to the power substrate with high voltage power die compressively held between the board and the substrate. The compressive hold enhances the electrical connections between the contacts on the top and bottom of the power die and either the power substrate or the printed circuit board. Exterior blade connectors extend upward from the printed circuit board through blade apertures in a lid that covers the interior compartment. The lid includes corona extenders positioned around the blade apertures to allow for high voltage applications while maintaining a small size lightweight package. The sidewall has a perimeter that also includes one or more corona extenders.

42 ENGINEERING↗

Extreme-bandwidth scalable performance-per-watt GPU architecture

A technique for accessing memory in an accelerated processing device coupled to stacked memory dies is provided herein. The technique includes receiving a memory access request from an execution unit and identifying whether the memory access request corresponds to memory cells of the stacked dies that are considered local to the execution unit or non-local. For local accesses, the access is made “directly”, that is, without using a bus. A control die coordinates operations for such local accesses, activating particular through-silicon-vias associated with the memory cells that include the data for the access. Non-local accesses are made via a distributed cache fabric and an interconnect bus in the control die. Various other features and details are provided below.

97 MATHEMATICS AND COMPUTING↗

Tooling assembly and method for explosively forming features in a thin-walled cylinder

The present invention provides a method of explosively forming a helical tube from at least one thin-walled cylinder using a tooling assembly. The method includes inserting the at least one thin-walled cylinder into a die of the tooling assembly. The die surrounds the at least one thin-walled cylinder and includes an interior surface that defines a helical thread pattern. The method further includes surrounding the at least one thin-walled cylinder and the die with a casing of the tooling assembly. A cavity is defined by the casing and the thin-walled cylinder. The method further includes positioning an explosive charge within the cavity. The method additionally includes at least partially submerging the tooling assembly. The method further includes detonating the explosive charge. As a result, the at least one thin-walled cylinder is formed into a helical tube that corresponds with helical thread pattern of the interior surface of the die.

Eberl, Kurt R.↗

Eco–Friendly Solvent Engineered CsPbI 2.77 Br 0.23 Ink for Large–Area and Scalable High Performance Perovskite Solar Cells

The performance of large-area perovskite solar cells (PSCs) has been assessed for typical compositions, such as methylammonium lead iodide (MAPbI 3 ), using a blade coater, slot-die coater, solution shearing, ink-jet printing, and thermal evaporation. However, the fabrication of large-area all-inorganic perovskite films is not well developed. This study develops, for the first time, an eco-friendly solvent engineered all-inorganic perovskite ink of dimethyl sulfoxide (DMSO) as a main solvent with the addition of acetonitrile (ACN), 2-methoxyethanol (2-ME), or a mixture of ACN and 2-ME to fabricate large-area CsPbI 2.77 Br 0.23 films with slot-die coater at low temperatures (40–50 °C). The perovskite phase, morphology, defect density, and optoelectrical properties of prepared with different solvent ratios are thoroughly examined and they are correlated with their respective colloidal size distribution and solar cell performance. Here, the optimized slot-die-coated CsPbI 2.77 Br 0.23 perovskite film, which is prepared from the eco-friendly binary solvents dimethyl sulfoxide:acetonitrile (0.8:0.2 v/v), demonstrates an impressive power conversion efficiency (PCE) of 19.05%. Moreover, the device maintains ≈91% of its original PCE after 1 month at 20% relative humidity in the dark. It is believed that this study will accelerate the reliable manufacturing of perovskite devices.

binary and ternary solvent↗

Corrosion Behavior of AZ31 Magnesium Alloy Produced by Continuous Variable Cross Section Direct Extrusion

In order to study the corrosion behavior of magnesium alloys of high performance in the simulated seawater by continuous variable cross section direct extrusion (CVCDE), an electrochemical method and weight loss method were used to study the difference between AZ31 magnesium alloys produced by CVCDE with different numbers of interim dies to examine the electrochemical corrosion behavior and corrosion rate at 3.5 wt.% NaCl solution in this paper. Scanning electron microscopy and x-ray diffraction were used to analyze the morphology of corrosion surfaces and the composition of the corrosion products of samples soaked for different times. The results show that after CVCDE with different numbers of interim dies, the size of the microstructure is refined gradually, and the grain orientation is also different; with the increase in the number of interim dies, the thermodynamic corrosion tendencies are different, and the corrosion resistance of samples extruded by conventional extrusion is relatively good; the charge transfer and material transfer process are the two main factors affecting the corrosion rate, which determines the direction of the electrochemical reaction; the corrosion form of the sample extruded by CVCDE is the local corrosion which is the filiform corrosion and pitting corrosion, and the corrosion product is mainly water-insoluble Mg(OH){sub 2}.

36 MATERIALS SCIENCE↗