Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Control Theory”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Hybrid Feedforward-Feedback Noise Control Using Virtual Sensors

Several approaches to active noise control using virtual sensors are evaluated for eventual use in an active headrest. Specifically, adaptive feedforward, feedback, and hybrid control structures are compared. Each controller incorporates the traditional filtered-x least mean squares algorithm. The feedback controller is arranged in an internal model configuration to draw comparisons with standard feedforward control theory results. Simulation and experimental results are presented that illustrate each controllers ability to minimize the pressure at both physical and virtual microphone locations. The remote microphone technique is used to obtain pressure estimates at the virtual locations. It is shown that a hybrid controller offers performance benefits over the traditional feedforward and feedback controllers. Stability issues associated with feedback and hybrid controllers are also addressed. Experimental results show that 15-20 dB reduction in broadband disturbances can be achieved by minimizing the measured pressure, whereas 10-15 dB reduction is obtained when minimizing the estimated pressure at a virtual location.

Bean, Jacob↗

A Novel Sliding Mode Network Perimeter Controller

Congestion in urban areas is a chronic problem that faces many US and worldwide cities. It results in inefficient use of the infrastructure as well as increased fuel consumption and vehicle emissions. Congestion is intertwined with delay. Road users waste precious hours on the road, which reduces productivity. Throughout this decade researchers were and are developing tools and systems that alleviate this problem. Network perimeter control is one of these tools that has been studied extensively. It attempts to control the flow of vehicles entering a protected area so as not to reach the congested regime that is pre-determined using the Network Fundamental Diagram (NFD). In this paper, we present a novel and simple approach derived from sliding mode control theory that achieves the desired objective. Its main advantages over other control strategies include but are not limited to (1) ease of implementation, (2) minimal and straightforward model tuning, and (3) high performance. This controller was implemented and tested on a congested grid network. The results show that, the new logic performs as expected, producing network-wide delay savings that are consistent with other control approaches described in the literature. Furthermore, unlike other controllers, we demonstrate that the controller is robust to its hyper-parameter values, making the algorithm easy to implement and calibrate to local conditions. http://pubsindex.trb.org/

Sliding mode control, network perimeter control, n↗

A Review: Indirect Optimal Control of Wave Energy Converters

Wave energy conversion has been the subject of interest in the past several years. While there are several concepts for converting wave power into electric power, the cost of the electric power harvested from ocean waves remains high. One of the main challenges, though it receives less attention, is the control of the wave energy converter (WEC). This paper presents a treatment for the WEC control problem within the context of optimal control theory. The result is systematic development for an explicit expression for a control that maximizes the harvested energy while meeting operational constraints such as the maximum device stroke and the maximum control force. The control presented here can also be adjusted to meet device design constraints such as a limitation on the amount of reactive power available from the power take-off (PTO) unit; this feature enables a control co-design for the PTO unit. Numerical simulations are presented in this paper for demonstration.

control design↗

NASA propulsion controls research

Multivariable control theory is applied to the design of multiple input and output engine controls. Highly-accurate, real-time engine simulations are utilized for control development and checkout. Electro-optical control components are developed for use in electronic control systems having fiber optic data links. Integrated controls are developed for VSTOL and Rotorcraft propulsion systems. Post-stall models of engine systems are developed to aid in understanding and control of post-stall engine behavior.

Teren, F.↗

Task driven feedback control of robot arms - A step toward intelligent control

The process of connecting task descriptions originating from machine intelligence planning programs to the mechanization of feedback control of robot arms is analyzed. It is shown in this paper that control theories and practices can be extended to a higher level where feedback control of robot arms directly can respond to work space task commands provided that the work space task as a command is given in the form of a closed function of time. A general mathematical procedure using tools from differential geometry is introduced for synthesizing task space motion planning so that the planned motion can be used as a direct input to the robot arm feedback control system to achieve desired robot hand motion. By definition, 'intelligent control' is being manifested through robot performance in the task space relative to task space commands. Thus, the capability of implementing feedback control of robot arms directly driven by appropriate task descriptions in the workspace as commands is a step toward intelligent control.

Bejczy, A. K.↗

Optimal Angle of Attack Control for Aerocapture Maneuvers

Recent investigations of aerocapture maneuvers have considered direct force control as a promising alternative to bank angle control. By modulating the angle of attack and sideslip angle independently, the longitudinal and lateral channels can be decoupled and thus solved separately. However, the optimal angle of attack profile for minimizing post-atmospheric propellant expenditure was previously unknown. This research applies principles of optimal control theory to numerically solve for the optimal angle of attack profile for control of the longitudinal channel. Direct methods are first employed to discretize the angle of attack profile and show that an optimal solution follows a nearly bang-bang (full lift up then full lift down) structure under a variety of conditions along the flight path angle corridor. To corroborate these results, indirect methods were also applied to scope the Optimal Control Problem (OCP) as a Two Point Boundary Value Problem (2P-BVP) which could then be solved numerically. The indirect optimization results aligned closely with the direct results, providing further evidence that a bang-bang structure provides a good approximation for the optimal angle of attack profile for aerocapture maneuvers using direct force control.

aerocapture↗

Analogy Between the Collatz Conjecture and Sliding Mode Control

The Collatz Conjecture is a famous mathematics problem that is simple to state and understand but remains unsolved. In this paper, the problem is recast as a discrete-time nonlinear system. and viewed in a new light from the perspective of nonlinear systems and feedback control theory. In particular, connections are made between the Collatz sequence of numbers and the behavior of closed-loop dynamical systems designed using a feedback control method called sliding mode control. Trajectories of such systems are characterized by a reaching phase and a sliding phase, the latter of which exhibits exponential convergence. As sliding mode control design is rooted in Lyapunov stability theory, the analogy suggests a new direction for proving or disproving the Collatz Conjecture. Although several possible approaches are discussed, no formal proof is given in this paper.

Collatz conjecture↗

Communication system modeling

This report presents the results of work on communications systems modeling and covers three different areas of modeling. The first of these deals with the modeling of signals in communication systems in the frequency domain and the calculation of spectra for various modulations. These techniques are applied in determining the frequency spectra produced by a unified carrier system, the down-link portion of the Command and Communications System (CCS). The second modeling area covers the modeling of portions of a communication system on a block basis. A detailed analysis and modeling effort based on control theory is presented along with its application to modeling of the automatic frequency control system of an FM transmitter. A third topic discussed is a method for approximate modeling of stiff systems using state variable techniques.

Holland, L. D.↗

Structural tailoring and feedback control synthesis - An interdisciplinary approach

Structural tailoring provides an attractive method to optimize the performance of actively controlled space structures. However, the simultaneous optimization of control gains and structural properties often becomes prohibitively expensive for large systems and physical insight is often lost in the resulting control law. This paper presents a method for optimization of the closed loop structural system using only structural tailoring. Optimal Linear Quadratic Regulator (LQR) control theory is used with weighting matrices chosen based on physical considerations. The LQR control law depends only on two scalar gains and the structural properties. Hence, the closed loop-performance can be expressed in terms of the structural parameters. Results are given for a beam and a truss-beam to show the simplicity of the method and the importance of structural tailoring to increase dynamic performance and to reduce the control effort.

Belvin, W. Keith↗

Active flutter and gust response control

After a short recall concerning the aeroelastic equations, active control law based on optimal stochastic control theory is synthesized for a wing flutter and gust response. Robustness of the control system due to structured and unstructured uncertainties is considered. Robustness recovery technique is applied to improve the stability margin.

Oli, Muluneh↗

An Integrated Approach to Damage Accommodation in Flight Control

In this paper we present an integrated approach to in-flight damage accommodation in flight control. The approach is based on Multiple Models, Switching and Tuning (MMST), and consists of three steps: In the first step the main objective is to acquire a realistic aircraft damage model. Modeling of in-flight damage is a highly complex problem since there is a large number of issues that need to be addressed. One of the most important one is that there is strong coupling between structural dynamics, aerodynamics, and flight control. These effects cannot be studied separately due to this coupling. Once a realistic damage model is available, in the second step a large number of models corresponding to different damage cases are generated. One possibility is to generate many linear models and interpolate between them to cover a large portion of the flight envelope. Once these models have been generated, we will implement a recently developed-Model Set Reduction (MSR) technique. The technique is based on parameterizing damage in terms of uncertain parameters, and uses concepts from robust control theory to arrive at a small number of "centered" models such that the controllers corresponding to these models assure desired stability and robustness properties over a subset in the parametric space. By devising a suitable model placement strategy, the entire parametric set is covered with a relatively small number of models and controllers. The third step consists of designing a Multiple Models, Switching and Tuning (MMST) strategy for estimating the current operating regime (damage case) of the aircraft, and switching to the corresponding controller to achieve effective damage accommodation and the desired performance. In the paper present a comprehensive approach to damage accommodation using Model Set Design,MMST, and Variable Structure compensation for coupling nonlinearities. The approach was evaluated on a model of F/A-18 aircraft dynamics under control effector damage, augmented by nonlinear cross-coupling terms and a structural dynamics model. The proposed approach achieved excellent performance under severe damage effects.

Boskovic, Jovan D.↗

Adaptive Control of Non-Minimum Phase Modal Systems Using Residual Mode Filters2

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will modify the adaptive controller with a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. This paper will be divided into two parts. Here in Part I we will review the basic adaptive control approach and introduce the primary ideas. In Part II, we will present the RMF methodology and complete the proofs of all our results. Also, we will apply the above theoretical results to a simple flexible structure example to illustrate the behavior with and without the residual mode filter.

Balas, Mark J.↗

Adaptive Control Using Residual Mode Filters Applied to Wind Turbines

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a model reference direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will augment the adaptive controller using a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. We apply these theoretical results to design an adaptive collective pitch controller for a high-fidelity simulation of a utility-scale, variable-speed wind turbine that has minimum phase zeros.

Frost, Susan A.↗

Comparing Control Performance Between Simulation and Experiment using the Microreactor Automated Control System Testbed

In the advanced reactor domain, a flexible and scalable software/hardware infrastructure is crucial for integrating and validating various control technologies. This study used the Microreactor Automated Control System (MACS) hardware platform as a testbed. MACS was originally designed to mirror Idaho National Laboratory (INL)'s Microreactor Applications Research Validation and Evaluation (MARVEL), a 85-kW thermal fission microreactor. It features control drums for simulated reactivity control; lights that function as a surrogate reactor core, with the brightness being proportional to the reactor power; and light sensors that emulate neutron detectors. To transform MACS into a physical twin of MARVEL for evaluating control methods, the Control and Optimization Modular Modeling Application for Nuclear Deployment (COMMAND) software was employed. This software integrated the hardware with two models of the MARVEL core, based on Reactor Excursion and Leak Analysis Program (RELAP5-3D) and Monte Carlo N-Particle (MCNP) models. The study aimed to demonstrate the gap between control theory and actual practice—a gap that often necessitates empirical adjustments such as control gain retuning, filters, time discretization, and integrator anti-windup measures. Controllers were developed based on increasingly complex simulations without hardware, starting from the base MARVEL model and then introducing actuator saturation constraints and sensor noise. The final control strategy was then tested using MACS, and a comparative performance analysis was conducted.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗

Relationships between digital signal processing and control and estimation theory

Research areas associated with digital signal processing and control and estimation theory are identified. Particular attention is given to image processing, system identification problems (parameter identification, linear prediction, least squares, Kalman filtering), stability analyses (the use of the Liapunov theory, frequency domain criteria, passivity), and multiparameter systems, distributed processes, and random fields.

Willsky, A. S.↗