Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Air- and oxygen-broadening coefficients for the O2 rotational line at 60.46/cm

Using an NBS laser-based tunable far-infrared spectrometer, the air- and oxygen-broadening coefficients were measured for the J = 10 - 10, N = 11 - 9 O2 rotational transition at 60.46/cm (1.812 THz). The air-broadening coefficient is 5.04 + or - 0.38 x 10 to the -7th/cm/Pa (0.0511 + or - 0.0039/cm/atm) (HWHM) at 245 + or - 6 K; the oxygen-broadening coefficient is 4.92 + or - 0.47 x 10 to the -7th/cm/Pa (0.0499 + or - 0.0048/cm/atm) (HWHM) at 259 + or -2 K. These direct experimental measurements of the air-broadening coefficient should improve the accuracy of retrieval calculations for far-infrared stratospheric balloon experiments which use O2 rotational lines to calibrate the viewing geometry.

Jennings, D. A.↗

Use of a liquid-crystal and heater-element composite for quantitative, high-resolution heat-transfer coefficients on a turbine airfoil including turbulence and surface-roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, S. A.↗

Annular honeycomb seals: Test results for leakage and rotordynamic coefficients; comparisons to labyrinth and smooth configurations

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals show the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluid entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

Childs, Dara W.↗

Annular honeycomb seals: Test results for leakage and rotordynamic coefficients - Comparisons to labyrinth and smooth configurations

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals shows the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluids entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

Childs, D.↗

Stabilized determination of geopotential coefficients by the mixed hom-BLUP approach

For the determination of geopotential coefficients, data can be used from rather different sources, e.g., satellite tracking, gravimetry, or altimetry. As each data type is particularly sensitive to certain wavelengths of the spherical harmonic coefficients it is of essential importance how they are treated in a combination solution. For example the longer wavelengths are well described by the coefficients of a model derived by satellite tracking, while other observation types such as gravity anomalies, delta g, and geoid heights, N, from altimetry contain only poor information for these long wavelengths. Therefore, the lower coefficients of the satellite model should be treated as being superior in the combination. In the combination a new method is presented which turns out to be highly suitable for this purpose due to its great flexibility combined with robustness.

Middel, B.↗

Second coefficient of viscosity in air

Acoustic attenuation measurements in air were analyzed in order to estimate the second coefficient of viscosity. Data over a temperature range of 11 C to 50 C and at relative humidities between 6 percent and 91 percent were used. This analysis showed that the second coefficient of viscosity varied between 1900 and 20,000 times larger than the dynamic or first coefficient of viscosity over the temperature and humidity range of the data. In addition, the data showed that the molecular relaxation effects, which are responsible for the magnitude of the second coefficient of viscosity, place severe limits on the use of time-independent, thermodynamic equations of state. Compressible flows containing large streamwise velocity gradients, like shock waves, which cause significant changes in particle properties to occur during time intervals shorter than hundredths of seconds, must be modeled using dynamic equations of state. The dynamic model approach is described briefly.

Ash, Robert L.↗

The development and analysis of geopotential coefficient models to spherical harmonic degree 360

Two new geopotential coefficient models to spherical harmonic degree 360 are developed using recent advances made in theoretical modeling methods, satellite gravitational models, and expanded and improved terrestrial data. The new models are based on the combination of a satellite potential coefficient model (GEM-T2) to degree 50 with 30-arc mean gravity anomalies, yielding an adjusted set of coefficients and gravity anomalies, which were then harmonically analyzed to yield a set of potential coefficients to degree 360. The models were verified in several ways including satellite orbit residual analysis, demonstrating a substantial improvement over previous high-degree expansions.

Rapp, Richard H.↗

The Ohio State 1991 geopotential and sea surface topography harmonic coefficient models

The computation is described of a geopotential model to deg 360, a sea surface topography model to deg 10/15, and adjusted Geosat orbits for the first year of the exact repeat mission (ERM). This study started from the GEM-T2 potential coefficient model and it's error covariance matrix and Geosat orbits (for 22 ERMs) computed by Haines et al. using the GEM-T2 model. The first step followed the general procedures which use a radial orbit error theory originally developed by English. The Geosat data was processed to find corrections to the a priori geopotential model, corrections to a radial orbit error model for 76 Geosat arcs, and coefficients of a harmonic representation of the sea surface topography. The second stage of the analysis took place by doing a combination of the GEM-T2 coefficients with 30 deg gravity data derived from surface gravity data and anomalies obtained from altimeter data. The analysis has shown how a high degree spherical harmonic model can be determined combining the best aspects of two different analysis techniques. The error analysis was described that has led to the accuracy estimates for all the coefficients to deg 360. Significant work is needed to improve the modeling effort.

Rapp, Richard H.↗

Estimation of high temperature metal-silicate partition coefficients

It has been known for some time that abundances of siderophile elements in the upper mantle of the Earth are far in excess of those expected from equilibrium between metal and silicate at low pressures and temperatures. Murthy (1991) has re-examined this excess of siderophile element problem by estimating liquid metal/liquid silicate partition coefficients reduces from their measured values at a lower temperature, implying that siderophile elements become much less siderophilic at high temperatures. Murthy then draws the important conclusion that metal/silicate equilibrium at high temperatures can account for the abundances of siderophile elements in the Earth's mantle. Of course, his conclusion is critically dependent on the small values of the partition coefficients he calculates. Because the numerical values of most experimentally-determined partition coefficients increase with increasing temperature at both constant oxygen fugacity and at constant redox buffer, we think it is important to try an alternative extrapolation for comparison. We have computed high temperature metal/silicate partition coefficients under a different set of assumptions and show that such long temperature extrapolations yield values which are critically dependent upon the presumed chemical behavior of the siderophile elements in the system.

Jones, John H.↗

Stiffness and thermoelastic coefficients for composite laminates

Simple analytic expressions are presented for the stiffness and thermoelastic coefficients of composite laminates in terms of the material properties of the individual layers. Expressions for the derivatives of the various coefficients with respect to each of the material properties and fiber orientation angles are also included. For typical high-performance composites, numerical values are given showing the effects of the stacking sequence and the fiber orientation angle of quasi-isotropic and angle-ply laminates on the values of the various coefficients and their sensitivity derivatives. The expressions for the thermoelastic coefficients and the sensitivity derivatives are given herein for the first time.

Noor, Ahmed K.↗

Accuracy of critical-temperature sensitivity coefficients predicted by multilayered composite plate theories

An assessment is made of the accuracy of the critical-temperature sensitivity coefficients of multilayered plates predicted by different modeling approaches, based on two-dimensional shear-deformation theories. The sensitivity coefficients considered measure the sensitivity of the critical temperatures to variations in different lamination and material parameters of the plate. The standard of comparison is taken to be the sensitivity coefficients obtained by the three-dimensional theory of thermoelasticity. Numerical studies are presented showing the effects of variation in the geometric and lamination parameters of the plate on the accuracy of both the sensitivity coefficients and the critical temperatures predicted by the different modeling approaches.

Noor, Ahmed K.↗

Series integration of the diaphragm cell transport equation when the diffusion coefficient is a function of concentration

An integral of the form, t = B0 + BL ln(Delta-c) + B1(Delta-c) + B2(Delta-c)-squared + ..., where t is the time and Delta-c is the concentration difference across the frit, is derived in the case of the diaphragm cell transport equation where the interdiffusion coefficient is a function of concentration. The coefficient, B0, is a constant of the integration, while the coefficients, BL, B1, B2,..., depend in general upon the constant, the compartment volumes, and the interdiffusion coefficient and various of its concentration derivatives evaluated at the mean concentration for the cell. Explicit formulas for BL, B1, B2,... are given.

Cain, Judith B.↗

Calculation of stiffness and damping coefficients for elastically supported gas foil bearings

The stiffness and damping coefficients of an elastically supported gas foil bearing are calculated. A perfect gas is used as the lubricant, and its behavior is described by the Reynolds equation. The structural model consists only of an elastic foundation. The fluid equations and the structural equations are coupled. A perturbation method is used to obtain the linearized dynamic coefficient equations. A finite difference formulation has been developed to solve for the four stiffness and the four damping coefficients. The effect of the bearing compliance on the dynamic coefficients is discussed in this paper.

Peng, J.-P.↗

Strain energy of thermally stressed multilayer panels and its sensitivity coefficients

A study is made of the effect of lamination and material parameters of thermally stressed multilayer composite panels on the strain energy and its sensitivity coefficients obtained by the three-dimensional thermoelasticity model. The sensitivity coefficients measure the sensitivity of the strain energy to variations in the different lamination and material parameters of the panel. The strain energy and sensitivity coefficients obtained by the three-dimensional model are used as the basis for assessing the accuracy of the corresponding quantities obtained by two-dimensional first-order shear deformation theory. Numerical results are presented for antisymmetrically laminated angle-ply panels subjected to linear temperature variation through the thickness. The numerical results demonstrate the accuracy of the strain energy and its sensitivity coefficients obtained by the first-order shear deformation theory, for the range of parameters considered, and the importance of the particular terms in the strain energy, which vanish for single-layer panels.

Noor, Ahmed K.↗

A parameter identification method for the rotordynamic coefficients of a high Reynolds number hydrostatic bearing

In identifying the rotordynamic coefficients of a high-Reynolds-number hydrostatic bearing, fluid-flow induced forces present a unique problem, in that they provide an unmeasureable and uncontrollable excitation to the bearing. An analysis method is developed that effectively eliminates the effects of fluid-flow induced excitation on the estimation of the bearing rotordynamic coefficients, by using power spectral densities. In addition to the theoretical development, the method is verified experimentally by single-frequency testing, and repeatability tests. Results obtained for a bearing are the twelve rotordynamic coefficients (stiffness, damping, and inertia coefficients) as functions of eccentricity ratio, speed, and supply pressure.

Rouvas, C.↗

Absolute Coefficients and the Graphical Representation of Airfoil Characteristics

It is argued that there should be an agreement as to what conventions to use in determining absolute coefficients used in aeronautics and in how to plot those coefficients. Of particular importance are the absolute coefficients of lift and drag. The author argues for the use of the German method over the kind in common use in the United States and England, and for the Continental over the usual American and British method of graphically representing the characteristics of an airfoil. The author notes that, on the whole, it appears that the use of natural absolute coefficients in a polar diagram is the logical method for presentation of airfoil characteristics, and that serious consideration should be given to the advisability of adopting this method in all countries, in order to advance uniformity and accuracy in the science of aeronautics.

Munk, Max↗

Intermittent-flow coefficients of a poppet valve

Flow coefficients were determined for the inlet valve of a modern air-cooled cylinder during operation of the valve. The cylinder head with valves was mounted on a large tank that could be evacuated. Operating the valve with a rotating cam allowed air to flow through the valve into the evacuated tank. The change of pressure in the tank was a measure of the amount of air flowing though the valve in a given number of cycles. The flow coefficients were determined from the pressure across the valve, the quantity of air flowing, and the valve-lift curve. Coefficients were measured with lifts of 0.1 to 0.6 inch and speeds of 130 to 1,200 r.p.m. The results obtained with intermittent flow were compared with the results of tests made with steady flow through this cylinder head. This comparison indicated that steady-flow coefficients can be used for intermittent flow.

Waldron, C D↗

Determination of blade-to-coolant heat-transfer coefficients on a forced-convection, water-cooled, single-stage turbine

Blade-to-coolant convective heat-transfer coefficients were obtained on a forced-convection water-cooled single-stage turbine over a large laminar flow range and over a portion of the transition range between laminar and turbulent flow. The convective coefficients were correlated by the general relation for forced-convection heat transfer with laminar flow. Natural-convection heat transfer was negligible for this turbine over the Grashof number range investigated. Comparison of turbine data with stationary tube data for the laminar flow of heated liquids showed good agreement. Calculated average midspan blade temperatures using theoretical gas-to-blade coefficients and blade-to-coolant coefficients from stationary-tube data resulted in close agreement with experimental data.

COOLING - GAS TURBINE SYSTEMS↗