Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of Dopant Compensation on the Conductivity of the Intrinsic poly-Si Isolation Region in Passivated IBC Silicon Solar Cells

The performance of IBC solar cells depends on the ability of this region to electrically isolate the doped fingers so that shunting does not occur and reduce the cell fill factor. We report on simulations which model the region between the p- and n-type poly-Si fingers of interdigitated back contact (IBC) solar cells as a series of resistors extending from one doped finger to the other. We demonstrate that the existence of a well compensated region between the doped fingers is enough to prevent shunting and loss of cell performance, despite contamination of dopants from the opposing dopant fingers. We show through these simulations that a net doping concentration below ~1018 cm-3 will enable a high resistivity and identify the conditions under which this highly resistive region forms despite imperfect finger edges. Additionally, we apply this analysis to tails measured by time-of-flight secondary ion mass spectrometry and confirm this hypothesis for our experimentally measured tails.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Diffusion study of uranium mononitride/zirconium carbide composite for space nuclear propulsion

Here, the next generation of space exploration will require extensive developments in rocket technology. Space nuclear propulsion is of interest due to its high fuel density and power, however, it also has high temperature and stability demands. This study examines a uranium nitride/zirconium carbide ceramic-ceramic particle composite as a potential fuel for these missions. Based on the constituent properties, this fuel composite is expected to be highly thermally efficient and resistant to the hot hydrogen propellant. One of the main concerns with this composite is unknown diffusion behavior between UN and ZrC over time. Diffusion couples and composites were used to determine how these constituents will behave when left in contact at high temperatures. UN and ZrC were found to have limited but observable diffusion at the phase boundary. The resulting phase is a UZr(CN) quaternary phase. UZr(CN) has been examined for other high temperature and gas nuclear reactors with preliminary success; however, there lacks sufficient data to fully qualify this phase. Based on the limited information available, the resultant quaternary phase could be deemed acceptable and even provide better adhesion for the fuel particles (UN) to the matrix (ZrC).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Engineering Antifreeze Proteins to Optimally Resist Engulfment by Ice

Antifreeze proteins (AFPs) facilitate the survival of organisms in cold climates by inhibiting the growth and/or recrystallization of ice. To function, AFPs must first bind to ice crystals; bound AFPs must then resist engulfment by using their nonbinding side (NBS) to pin the ice–water interface. Here, we seek to understand how the molecular characteristics of an NBS, such as its ice-phobicity or shape, influence its ability to resist engulfment. By characterizing the free energy barriers that impede the engulfment of model AFPs, we find that the critical supercooling ΔT*, above which an AFP is engulfed, is dictated by an optimal pinning site on the NBS. We further find that the optimal pinning site is determined by an interplay between the contact line perimeter P and a pinning efficiency η, with ΔT* ∝ ηP at the optimal pinning site. For a hemispherical AFP, which displays progressively inward tapering, we find that η increases during engulfment, whereas P decreases; conversely, an NBS with outward tapering can achieve high P, but it suffers from low η. Because the product of η and P determines ΔT*, the inverse correlation between them limits ΔT. To circumvent such limiting behavior, we propose an NBS shape with an outward bulge; by initially tapering outward, a bulged NBS permits higher P, and by subsequently tapering inward, it promotes high η as well. Importantly, we find that ΔT* is enhanced by more than a factor of 2 with an outward bulge of only 1 nm. We also find that the more ice-phobic an NBS is, the more efficiently it pins the ice–water interface, resulting in a higher ΔT. Furthermore, our findings shed light on how the NBS molecular characteristics influence ΔT* and suggest strategies for engineering the NBS to optimally resist engulfment by ice.

Antifreeze↗
DOE OSTI2021

Two-terminal electronic charge resistance switching device

A two-terminal memory device and methods for its use are provided. In the device, a bottom electrode is electrically continuous with a first operating terminal, and a control gate electrode is electrically continuous with a second operating terminal. A stack of insulator layers comprising a hopping conduction layer and a tunnel layer is contactingly interposed between the bottom electrode and the control gate electrode. The tunnel layer is thinner than the hopping conduction layer, and it has a wider bandgap than the hopping conduction layer. The hopping conduction layer consists of a material that supports electron hopping transport.

Marinella, Matthew↗
DOE OSTI2024

Dual material fused filament fabrication of composite core‐shell structures with improved impact resistance and interfacial adhesion

The mechanical performance of parts produced by fused filament fabrication (FFF) has been limited due to the presence of voids and poor interlayer welding. Recent advancements in FFF have enabled the fabrication of void-free objects with strong interlayer welding through the use of semicrystalline polymer shells such as high-density polyethylene (HDPE) along with a high viscosity core polymer like acrylonitrile-butadiene-styrene (ABS). Furthermore, the zero-shear viscosity (η0) of ABS is three orders of magnitude higher than HDPE making the ABS-HDPE core-shell configuration preferable. ABS holds the shape by preventing bulk flow and part bending while HDPE promotes full surface contact across the layers. Most polymers, however, are immiscible which causes a weak weld line along the core-shell interface. Herein, maleic anhydride (MAH) is grafted to the butadiene segment of the ABS core thereby compatibilizing the interface with HDPE, improving the interfacial adhesion. Attenuated total reflectance-Fourier transform infrared spectroscopy was employed to confirm successful grafting. Using a custom-made die affording the core-shell structure, the ABS-g-MAH is shown to improve the impact resistance by 253% and 16% compared to neat HDPE and ABS specimens, respectively. Additionally, a 10% increase compared to the unmodified ABS-HDPE core-shell configuration is observed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electron doping of NdNiO 3 thin films using dual chamber CaH 2 annealing

Hydrogen donor doping has been exploited as a strategy to manipulate the electronic structure and electrical properties of functional oxide systems. Especially, the development of synthetic methods to achieve electron doping of perovskite rare-earth nickelate thin films utilizing interstitial hydrogen is highly desirable considering the rich electronic phase diagram hosting several functional properties. Here, in this work, we present the hydrogenation of NdNiO 3 (NNO) thin films using CaH 2 annealing and the resulting giant modulation of electrical resistivity in hydrogenated NNO (H–NNO) thin films. Magnetron sputtering was employed to deposit epitaxial ~60 nm-thin NNO films on single crystal LaAlO 3 (LAO) substrates. The formation of the pristine perovskite NNO phase was realized after annealing the films at 500 °C for 24 h. CaH 2 annealing of NNO thin films for time durations ranging from 1 to 6 h was performed in a vacuumed ampule with two interconnected chambers at 280 °C. The two-chamber design enables a simple and clean approach for hydrogen doping without physical contact between the powder and sample of interest. X-ray diffraction and Raman spectroscopy revealed the formation of NNO in pristine samples, and the subsequent hydrogen incorporation upon CaH 2 annealing without forming any impurity phases. The conversion of the oxidation state of Ni towards +2 upon CaH 2 annealing was probed using X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. Consequently, a substantial increase in the room-temperature resistivity was observed upon CaH 2 annealing indicating the formation of a strongly correlated electronic configuration of Ni in H–NNO due to electron doping. Overall, the findings of this study highlight the versatility of CaH 2 annealing as an electron doping method to tune the electrical properties of correlated oxides at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗
DOE OSTI2021

Characterization of front contact degradation in monocrystalline and multicrystalline silicon photovoltaic modules following damp heat exposure

Reliability and durability tests play a key role in the photovoltaic (PV) industry by minimizing potential failure risks for both existing and new cell and module technologies. In this work, a detailed study of contact degradation in monocrystalline and multicrystalline PV modules is performed. The modules are subjected to a sequence of damp heat (DH) exposures followed by electrical characterization after each step. Electroluminescence (EL) imaging shows different darkening patterns for monocrystalline modules compared to multicrystalline modules; the former shows darkening near the busbars and the latter shows it across virtually the entire cell surface. The primary loss mechanism is confirmed to be resistive after comparing the current-voltage (I–V) characteristics at each DH exposure step. Representative samples have been cored out from both the degraded modules and controls for materials characterization to gain further insights into the degradation mechanism. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and top-down high-resolution X-ray photoelectron spectroscopy (XPS) analysis performed on the cored samples confirm the degradation is due to metallization corrosion. Our study suggests that the difference in the darkening pattern can most likely be attributed to the different silver paste composition used for contacting each cell technology, particularly the composition of the glass frit.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Plasma Etching on Dopant Compensation between p- and n-Type Poly-Si Fingers in Passivated Interdigitated Back Contact Solar Cells

Efficiencies surpassing 26% have been achieved for single-junction Si solar cells based on the interdigitated back contact (IBC) architecture. However, the possibility of lateral shunting between the doped fingers has limited industrial adoption thus far. To avoid this possibility of shunt, complicated patterning techniques of the doped rear fingers have been developed, but spreading can still occur through multiple pathways during cell processing. Patterning can be simplified by using masked plasma-enhanced chemical vapor deposition (PECVD), but spreading during deposition will also lead to contamination of the isolation region between doped fingers. We significantly reduce the effect of this spreading through a short, gentle plasma etching step, which enables a trap-assisted compensation mechanism to take effect more easily than without the plasma etch. These two effects combined allow for the use of a simple patterning technique while still maintaining a highly resistive region between the doped fingers, and will reduce the complexity of IBC cell fabrication overall.

atom probe↗
DOE OSTI2020

Zero-Valent Iron Permeable Reactive Barrier to Remediate Volatile Organic Compounds in Groundwater - 20209

The US DOE-SRS, the US EPA, and the South Carolina Department of Health and Environmental Control determined it was appropriate to perform a non-time critical removal action at the P-Area Groundwater Operable Unit at the SRS to reduce the mass and downgradient transport of trichloroethylene in the P-Area groundwater plume. Contaminated groundwater discharges to a nearby stream, Steel Creek, within the SRS boundaries, resulting in trichloroethylene concentrations above the maximum contaminant level. Impact to surface water is limited in areal extent and supported by recently collected characterization data. The P-Area Groundwater Operable Unit encompasses the groundwater beneath an industrial area within SRS, P Area, where the P-Reactor once operated. The boundaries of the P-Area Groundwater Operable Unit extend northwest to Steel Creek, northeast toward PAR Pond, and southeast to Meyers Branch. Groundwater in the Upper Three Runs Aquifer of the P-Area Groundwater Operable Unit has been impacted by reactor and facility operations between 1954 and 1991, including tritium and volatile organic compounds. The P-Area surface units contributing to groundwater contamination were remediated as part of the P-Area Operable Unit in 2011. The P-Reactor closure is one of the first of its kind in the DOE Complex and is one of only a few full-sized production reactors in the US to undergo completion of final closure activities. The nature and extent of groundwater contamination was determined using a variety of investigative approaches such as groundwater monitoring wells, direct-push technology, and surface water samples. Groundwater contamination associated with trichloroethylene is primarily exhibited in a narrow plume that extends from the source area at P-Reactor and west to Steel Creek. Maximum contaminant level exceedances in groundwater occur over an area of ∼6.9 hectares for trichloroethylene with concentrations as high as 7.7 milligrams per liter. To the west of the P-Area facility area, the trichloroethylene groundwater plume is controlled by a buried geologic feature, assumed to be an old stream bed, that further narrows the groundwater plume in what has been designated as the 'neck area.' This narrowing of the groundwater plume provides an ideal location for a treatment barrier. The non-time critical removal action alternative chosen is to install a zero-valent iron permeable reactive barrier within the neck area of the trichloroethylene groundwater plume, perpendicular to groundwater flow direction. This technology will provide a treatment barrier that will reduce trichloroethylene groundwater concentrations by 90% and has an anticipated useful life of at least 25 years. A pre-design investigation was performed in the neck area to confirm site lithology, hydrogeology, geochemistry, and extent of trichloroethylene contamination prior to a final design. A treatability study, conducted as part of the pre-design investigation, indicated that the subsurface and groundwater in the PArea Groundwater Operable Unit is compatible with the zero-valent iron and will not lead to excessive buildup from mineralization/precipitation or biofouling. Probabilistic modeling was conducted using field and laboratory data to determine the expected performance of the zero-valent iron permeable reactive barrier. The model simulations indicated that a 3.81-centimeter thick barrier would provide greater than 90% reduction of trichloroethylene groundwater concentration. The final design of the zero-valent iron permeable reactive barrier is a barrier that will extend 80.5 linear meters in a 'zigzag' orientation to best transect the trichloroethylene plume and account for varying groundwater flow. The barrier will be installed from 13.7 meters below ground surface to 41.1 meters below ground surface for 65.8 linear meters and from 13.7 meters below ground surface to 36.6 meters below ground surface for 14.6 linear meters, the base of which is 'keyed' into a low permeability zone. The barrier is designed to a thickness of 10.2 centimeters, which was determined to reduce the trichloroethylene groundwater concentrations by greater than 90% with a safety factor of 2.67. A total of approximately 689 metric tons of zero-valent iron will be injected through 22 injection wells spaced 3.66 meters apart, using guar to suspend the zero-valent iron. Zero-valent iron permeable reactive barrier construction will be monitored through 23 installed resistivity receivers offset 7.32 meters from the zerovalent iron permeable reactive barrier. The zero-valent iron will be energized with a low-voltage 100 Hertz signal during injection and will be monitored using the resistivity receivers to ensure complete coalescence of the zero-valent iron permeable reactive barrier. The zero-valent iron was sized to have a hydraulic conductivity greater than the natural subsurface, thus promoting groundwater flow through the barrier. As contaminated groundwater contacts the zero-valent iron, volatile organic compounds, including trichloroethylene, are immediately degraded to harmless compounds such as ethylene. The performance of the zero-valent iron permeable reactive barrier will be monitored using three upgradient monitoring well clusters, six downgradient monitoring well clusters, and four in-wall monitoring wells. The in-wall monitoring wells will indicate immediate reduction of trichloroethylene mass in the groundwater and allow analyses of the zero-valent iron permeable reactive barrier health. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Trap-Assisted Dopant Compensation Prevents Shunting in Poly-Si Passivating Interdigitated Back Contact Silicon Solar Cells

Using a trap-assisted compensation model, we explain why polycrystalline Si (poly-Si) passivating contacts are able to achieve low leakage current between the doped fingers of interdigitated back contact (IBC) monocrystalline Si solar cells despite mixing of boron and phosphorus dopants in the isolation region. The fill factor of IBC solar cells is strongly affected by the electrical isolation region between n- and p-type fingers, as this region is critical in minimizing shunting losses. During fabrication of monocrystalline Si solar cells with poly-Si passivating contacts, the intrinsic poly-Si isolation region inevitably gets contaminated with both p- and n-type dopants. Using dopant profiles measured with time-of-flight secondary ion mass spectrometry and scanning probe measurements of the isolation region, we demonstrate that despite the dopant spreading during cell processing, a well-compensated region between the doped fingers exists that prevents shunting. The trap-assisted dopant compensation mechanism significantly widens the compensated region to tens of microns, where the residual dopant densities are below the trap density. This enables a high-resistivity region, resulting in low shunt current. Using one-dimensional (1-D) finite element diode simulations, we identify the design parameters and experimental conditions under which a sufficiently resistive region can form. Furthermore, our measurements of 2-D local resistivity and work function maps across the isolation region using scanning spreading resistance microscopy and Kelvin probe force microscopy demonstrate the existence of a highly resistive, wide compensated region and confirm our proposed compensation mechanism. For our structures, this region is ~25 µm in width within a ~150 µm wide finger isolation region with nearly 3 orders of magnitude higher resistivity than the regions dominated by a single type of dopant.

14 SOLAR ENERGY↗
DOE OSTI2021

Trap-Assisted Dopant Compensation Prevents Shunting in poly-Si Passivating Interdigitated Back Contact Silicon Solar Cells

Interdigitated back contact (IBC) solar cells achieve the highest efficiencies of single-junction architectures, but complicated patterning of the rear fingers and spreading of dopants during processing inhibit their mainstream adoption due to concerns of shunting between the IBC fingers. One method of simplifying patterning at the rear is by using contact masks combined with plasma-enhanced chemical vapor deposition (PECVD) or ion implantation. However, the intrinsic isolation region becomes contaminated during high-temperature annealing by lateral diffusion of dopants and during masked PECVD by spreading of dopant radicals through region between the mask and the substrate. Despite this contamination, we show through scanning spreading resistance microscopy and Kelvin probe force microscopy that a ~20 µm wide compensating region exists with high enough resistivity to prevent shunting. We model this p-i-n poly-Si system using two simulation models: a simple resistor model considering only the capture of charge carriers by trap defects in poly-Si to reduce the conductivity, and a more refined 1-dimensional finite element model using Poisson’s equation, drift-diffusion equations, and recombination of carriers. Using this model, we show that high defect density significantly decreases the current across the region between the p- and n-type fingers, preventing shunting.

atom probe↗
DOE OSTI2021

Large aperture and durable glass-engraved optical metasurfaces using nanoparticle etching masks: prospects and future directions

Abstract Metasurfaces (MSs), or surfaces consisting of engineered spatially oriented sub-wavelength elements—also known as meta-atoms—are quickly becoming a burgeoning field of interest due to their seemingly unparalleled control over the propagation of light. This article will discuss the emergence of a MS technology that is based on dewetting thin metal films to form dry etching masks for MS fabrication. The novelty this process presents is the ability to spatially vary mask features—which translates into spatially varying index of the finished surface—in a way that, rather than writing subwavelength elements one-by-one, writes entire areas at once to provide a route to easily scale the process up to meter-sized optics. Glass-engraved MSs have shown to be laser damage resistant, with damage thresholds close to the parent substrate damage thresholds. Furthermore, these surfaces have proven to be mechanically durable and capable of handling normal loads two orders of magnitude higher than that of an average fingerprint pressure. This indicates that accidental handling contact is not detrimental to the MS optical performance. Also discussed are the foreseeable technological challenges, potential solutions for those obstacles, and some currently unexplored directions for future efforts.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Understanding the Mechanisms of Self-Organization in Atmospheric Pressure DC Glows

One of the most challenging areas in atmospheric pressure plasmas is controlling uniformity and contact area. Indeed it is this problem which is closely related to scale up that has impeded the widespread applications of these plasmas. The atmospheric pressure plasma glow is a type of atmospheric pressure discharge akin to a traditional low pressure glow particularly when compared with discharge morphology. But this is where the similarities end. Unlike low pressure glows, atmospheric pressure glows do not rely on electrode processes such as secondary electron emission to make the discharge self-sustaining, rather the discharge is sustained by typically processes such as the presence of a resistive layer or through favorable atomic collisional processes such as that which prevail in helium that stabilizes the discharge so that the thermal instability is mitigated. These discharges can feature either solid metal electrodes or geometries where at least one electrode is a liquid water electrolyte. Regardless of the implementation, DC 1 Atm glows are fascinating in that the plasma attachment under certain conditions can self-organize. The attachment surface area therefore changes as a result. Therefore, self-organization could be the key to optimizing plasma contact area and thereby open the door to applications in the real world. The plasma physical processes prevailing at the surface where the self-organization takes place remain largely unexplored. There is very little published research on the conditions that prevail at the surface and virtually no scholarship on measured plasma parameters of the self-organized attachments themselves or the surface electric field. This effort breaks new ground by elucidating these largely unexplored physical processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

CRADA 2022-03 Final Report: Advanced Bearing Materials for Harsh Service Conditions

Develop advanced bearing materials for hydrogen gas turbines and wind turbines. Two candidate materials have been selected based on Ames lab’s recent work on high entropy alloys and shape memory alloys. These materials are designed to exhibit a balance of hardness, strength, toughness, and corrosion resistance. The hydrogen diffusion coefficient in the NiTi based shape memory alloy is two order of magnitude lower than that of the conventional case hardened bearing steel. We plan to atomize these materials into powders, additive manufacture cylindrical bearings, then test these bearing for rolling-contact fatigue, corrosion properties, and hydrogen embrittlement. We are a vertically integrated team comprises of national labs, bearing manufacturers, raw material powders makers, and aircraft gas turbine manufacturer.

Argibay, Nicolas [Ames Laboratory (AMES), Ames, IA↗
DOE OSTI2022

Highly stretchable organic electrochemical transistors with strain-resistant performance

Realizing fully stretchable electronic materials is central to advancing new types of mechanically agile and skin-integrable optoelectronic device technologies. Here we demonstrate a materials design concept combining an organic semiconductor film with a honeycomb porous structure with biaxially prestretched platform that enables high-performance organic electrochemical transistors with a charge transport stability over 30-140% tensional strain, limited only by metal contact fatigue. In this work, the prestretched honeycomb semiconductor channel of donor-acceptor polymer poly(2,5-bis(2-octyldodecyl)-3,6-di(thiophen-2-yl)-2,5-diketo-pyrrolopyrrole-alt-2,5-bis(3-triethyleneglycoloxy-thiophen-2-yl) exhibits high ion uptake and completely stable electrochemical and mechanical properties over 1,500 redox cycles with 10(4) stretching cycles under 30% strain. Invariant electrocardiogram recording cycles and synapse responses under varying strains, along with mechanical finite element analysis, underscore that the present stretchable organic electrochemical transistor design strategy is suitable for diverse applications requiring stable signal output under deformation with low power dissipation and mechanical robustness. Highly stretchable organic electrochemical transistors with stable charge transport under severe tensional strains are demonstrated using a honeycomb semiconducting polymer morphology, thereby enabling controllable signal output for diverse stretchable bioelectronic applications.

36 MATERIALS SCIENCE↗