Results for “CFD modeling” — Page 24

NASA NTRS2018

Quantitative Analysis of Planar Laser-Induced Fluorescence Measurements in a Hypersonic Boundary Layer

Several quantitative measurements extracted from nitric oxide (NO) planar laser-induced fluorescence (PLIF) data obtained in a hypersonic boundary layer are reported: (a) off-body NO mole fraction; (b) surface heat flux; and (c) near-wall static temperature. The experimental data was obtained at NASA Langley Research Center’s 31 in. Mach 10 air tunnel. NO was seeded into the flow through a spanwise slot on the surface of the 10 degree half-angle wedge model. An ultraviolet planar laser sheet was positioned perpendicular to the wedge surface, downstream of the seeding slot, to excite six fluorescence transitions. A method for extracting the relative NO mole fraction, based on spatial variations of the J”= 0.5 PLIF signal, is presented. Combined with the principle of mass conservation, the absolute NO mole fraction is determined. These measurements were used to assess CFD diffusion modelling, correct previously reported PLIF thermometry results, and develop methods for NO-PLIF heat transfer measurements.

McDougall, Connor C.↗

NASA NTRSDate not supplied

Cryogenic Propellant Tank Self-Pressurization and Active Pressure Control

This AIAA Short Course lecture will present an overview of different experiments and computational modeling work that has been done to examine different aspects of pressurization and pressure control of a Cryogenic propellant tank. The lecture will cover several large-scale ground-based liquid Hydrogen cryogenic self-pressurization experiments that were performed at NASA Glenn and NASA Marshall, LN2 Nitrogen autogenous pressurization experiments, pressure control experiments using both subcooled jet mixing and subcooled droplet injection, and experiments that examined pressure drops that occur during tank sloshing. Numerical modeling and simulations that were done in association to these experiments as part of a comprehensive model validation effort will also be presented and discussed. Finally, the results of two simulant fluid pressurization and pressure control microgravity investigations performed as part of the Tank Pressure Control Experiment (TCPE) and The Zero-Boil-Off Tank (ZBOT)Experiment will also be presented.

Propellant Management↗

NASA NTRS1996

Flamelet Model Application for Non-Premixed Turbulent Combustion

The current Final Report contains results of the study which was performed in Scientific Research Center 'ECOLEN' (Moscow, Russia). The study concerns the development and verification of non-expensive approach for modeling of supersonic turbulent diffusion flames based on flamelet consideration of the chemistry/turbulence interaction (FL approach). Research work included: development of the approach and CFD tests of the flamelet model for supersonic jet flames; development of the simplified procedure for solution of the flamelet equations based on partial equilibrium chemistry assumption; study of the flame ignition/extinction predictions provided by flamelet model. The performed investigation demonstrated that FL approach allowed to describe satisfactory main features of supersonic H 2/air jet flames. Model demonstrated also high capabilities for reduction of the computational expenses in CFD modeling of the supersonic flames taking into account detailed oxidation chemistry. However, some disadvantages and restrictions of the existing version of approach were found in this study. They were: (1) inaccuracy in predictions of the passive scalar statistics by our turbulence model for one of the considered test cases; and (2) applicability of the available version of the flamelet model to flames without large ignition delay distance only. Based on the results of the performed investigation, we formulated and submitted to the National Aeronautics and Space Administration our Project Proposal for the next step research directed toward further improvement of the FL approach.

Secundov, A.↗

NASA NTRSDate not supplied

CFD Predictions of Boiling Regime Transitions during Line Chilldown validated against a 1G LN2 Experiment

Introduction Before filling a propellant tank on the ground or in Space, the transfer line between the donor and receiver tanks must be cooled down preferably by sacrificing a minimum amount of the cryogenic fluid. The cryogenic line chill-down process involves a transition between different flow boiling regimes, namely, film boiling, transition film boiling, and nucleate boiling which are complex and may be quite gravity-dependent. Capturing these boiling phenomena and predicting the transition between them in a CFD framework is new and challenging both for 1g and microgravity applications. Materials & Methods The present work addresses this challenge by employing a two-phase Eulerian approach in the context of a homogeneous fluid mixture together with the Lee phase change model to capture the film boiling regime of the chill-down process using ANSYS Fluent®. The nucleate boiling regime is predicted by incorporating an in-house developed sub-grid model that accounts for bubble nucleation, bubble growth, bubble departure diameter, and their shedding frequency. The sub-grid model is encoded and implemented into Fluent via a user-defined function for the wall-fluid heat flux calculations. The mathematical formulation and numerical implementation of the CFD model are described in detail. The coupled CFD-Subgrid model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Results Numerical simulation results show good agreements between the CFD predictions of the wall temperature evolution, rewetting temperature, and transition between film and nucleate boiling, with the experimental measurements published by Darr et al [2] for several different LN2 flowrates in the vertical pipe orientation. The CFD predictions for the wall temperature distribution indicate a rapid quenching of the wall at two upstream and downstream temperature sensing locations as compared to the experimental measurement. The only tuning parameter in the CFD model is the Lee mass transfer coefficient. The CFD Model predicts the Liedenfrost rewetting temperature in close agreement with the experiment. This marks a transition between stable and transitionary flow boiling regimes. The CFD-predicted boiling curve for the downstream sensor location is also compared against its experimental counterpart and indicates that the model is able to predict all the key temperature and heat flux parameters during the transitions from stable to transitionary film boiling to nucleate boiling in close agreement with the experiment. A sequence of predicted volume fraction, and temperature contours depicting these transitions will be presented.

Evaporation Condensation↗

NASA NTRS1993

CFD Parametric Study of Consortium Impeller

Current design of high performance turbopumps for rocket engines requires effective and robust analytical tools to provide design impact in a productive manner. The main goal of this study is to develop a robust and effective computational fluid dynamics (CFD) pump model for general turbopump design and analysis applications. A Finite Difference Navier-Stokes flow solver, FDNS, which includes the extended k-epsilon turbulence model and appropriate moving interface boundary conditions, was developed to analyze turbulent flows in turbomachinery devices. A second-order central difference scheme plus adaptive dissipation terms was employed in the FDNS code, along with a predictor plus multi-corrector pressure-based solution procedure. The multi-zone, multi-block capability allows the FDNS code to efficiently solve flow fields with complicated geometry. The FDNS code has been benchmarked by analyzing the pump consortium inducer, and it provided satisfactory results. In the present study, a CFD parametric study of the pump consortium impeller was conducted using the FDNS code. The pump consortium impeller, with partial blades, is a new design concept of the advanced rocket engines. The parametric study was to analyze the baseline design of the consortium impeller and its modification which utilizes TANDEM blades. In the present study, the TANDEM blade configuration of the consortium impeller considers cut full blades for about one quarter chord length from the leading edge and clocks the leading edge portion with an angle of 7.5 or 22.5 degrees. The purpose of the present study is to investigate the effect and trend of the TANDEM blade modification and provide the result as a design guideline. A 3-D flow analysis, with a 103 x 23 x 30 mesh grid system and with the inlet flow conditions measured by Rocketdyne, was performed for the baseline consortium impeller. The numerical result shows that the mass flow rate splits through various blade passages are relatively uniform. Due to the complexity of blade geometries, the TANDEM blade configurations were analyzed with the multi-zone grid structure. Both the 7.5 deg- and the 22.5 deg-clocking TANDEM blade cases utilized a 80K mesh system. The numerical result of two TANDEM blade modifications indicates the efficiency and the head are worse than those of the baseline case due to larger flow distortion. The gap between the TANDEM blade and the full blade allows the flow passes through and heavily loads the pressure side of the partial blade such that flow reversal occurs near the suction side of the splitter. The flow split at the exit of impeller blades is very non-uniform for TANDEM blade cases, and this will greatly induce the side load on the diffuser. Therefore, the TANDEM blade modification in the present CFD analysis does not improve the performance of the consortium impeller.

Cheng, Gary C.↗

NASA NTRS2002

Overview of NASA Multi-dimensional Stirling Convertor Code Development and Validation Effort

A NASA grant has been awarded to Cleveland State University (CSU) to develop a multi-dimensional (multi-D) Stirling computer code with the goals of improving loss predictions and identifying component areas for improvements. The University of Minnesota (UMN) and Gedeon Associates are teamed with CSU. Development of test rigs at UMN and CSU and validation of the code against test data are part of the effort. The one-dimensional (1-D) Stirling codes used for design and performance prediction do not rigorously model regions of the working space where abrupt changes in flow area occur (such as manifolds and other transitions between components). Certain hardware experiences have demonstrated large performance gains by varying manifolds and heat exchanger designs to improve flow distributions in the heat exchangers. 1-D codes were not able to predict these performance gains. An accurate multi-D code should improve understanding of the effects of area changes along the main flow axis, sensitivity of performance to slight changes in internal geometry, and, in general, the understanding of various internal thermodynamic losses. The commercial CFD-ACE code has been chosen for development of the multi-D code. This 2-D/3-D code has highly developed pre- and post-processors, and moving boundary capability. Preliminary attempts at validation of CFD-ACE models of MIT gas spring and "two space" test rigs were encouraging. Also, CSU's simulations of the UMN oscillating-flow fig compare well with flow visualization results from UMN. A complementary Department of Energy (DOE) Regenerator Research effort is aiding in development of regenerator matrix models that will be used in the multi-D Stirling code. This paper reports on the progress and challenges of this

Tew, Roy C.↗

NASA NTRS2021

Assessment and Improvement of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon the correlations that were derived from a limited number of low-speed experiments and do not account for all of the transition mechanisms and/or their variation with the significant flow parameters. Available data from a recent experiment in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.2o code for a swept wing configuration at transonic cruise conditions. Specifically, the OVERFLOW solutions are used together with detailed stability analysis of the boundary layer flow over the new Common Research Model with Natural Laminar Flow (CRM-NLF) to evaluate the accuracy and the robustness of the transport-equation-based transition models, with the goal of proposing improvements that would help to strengthen the physical basis of these models for the important class of flows involving the combined effects of crossflow and flow compressibility. Results highlight the significant underprediction of the laminar flow extent within the inboard region of the wing, wherein the onset of transition may be attributed to a gradual amplification of Tollmien-Schlichting instabilities.

Boundary layer transition↗

NASA NTRSDate not supplied

Transition Analysis for the Pazy Wing

The Pazy wing, designed as a benchmark for highly flexible wings that experience large deformations, presents intriguing nonlinear phenomena due to its unique geometry with spanwise varying static deformation and low Reynolds number flow conditions. These phenomena include limit cycle oscillation related to laminar separation bubbles, boundary-layer transition, and dynamic stall. The primary focus of this study is to investigate transition behavior on the sagged Pazy wing under static loading by using the shear-stress-transport (SST)-based Langtry-Menter 𝜸 − 𝑹𝒆𝜽𝒕 transition model in the NASA OVERFLOW and FUN3D solvers. Based on the steady-state results obtained via different variants of the Langtry-Menter model, we investigate the likely transition behavior over a range of incidence angles. The predicted flowfield on the sagged Pazy wing is strongly three dimensional and the application of turbulence index as a viable indicator of the transition front in such flows is also explored. The study demonstrates the limitations of the Langtry-Menter model when applied to low Reynolds number flows. We introduce a spanwise periodic configuration to simulate a narrow-span section of the Pazy wing, specifically centered on one of the 14 nearly equidistant ribs spanning the wing. The computational results demonstrate that the spanwise periodic configuration provides a straightforward environment for studying transition characteristics as well as demonstrating systematic grid convergence and successful code-to-code comparisons. The research offers useful insights into the transition characteristics of flexible wings under various loading conditions, contributing to the field of aeroelastic simulations.

CFD Modeling↗

NASA NTRSDate not supplied

Transition Analysis for the Pazy Wing

The Pazy wing, designed as a benchmark for highly flexible wings that experience large deformations, presents intriguing nonlinear phenomena due to its unique geometry with spanwise varying static deformation and low Reynolds number flow conditions. These phenomena include limit cycle oscillation related to laminar separation bubbles, boundary-layer transition, and dynamic stall. The primary focus of this study is to investigate transition behavior on the sagged Pazy wing under static loading by using the shear-stress-transport (SST)-based Langtry-Menter 𝜸 − 𝑹𝒆𝜽𝒕 transition model in the NASA OVERFLOW and FUN3D solvers. Based on the steady-state results obtained via different variants of the Langtry-Menter model, we investigate the likely transition behavior over a range of incidence angles. The predicted flowfield on the sagged Pazy wing is strongly three dimensional and the application of turbulence index as a viable indicator of the transition front in such flows is also explored. The study demonstrates the limitations of the Langtry-Menter model when applied to low Reynolds number flows. We introduce a spanwise periodic configuration to simulate a narrow-span section of the Pazy wing, specifically centered on one of the 14 nearly equidistant ribs spanning the wing. The computational results demonstrate that the spanwise periodic configuration provides a straightforward environment for studying transition characteristics as well as demonstrating systematic grid convergence and successful code-to-code comparisons. The research offers useful insights into the transition characteristics of flexible wings under various loading conditions, contributing to the field of aeroelastic simulations.

CFD Modeling↗

NASA NTRS1996

Turbulence Modeling: Progress and Future Outlook

Progress in the development of the hierarchy of turbulence models for Reynolds-averaged Navier-Stokes codes used in aerodynamic applications is reviewed. Steady progress is demonstrated, but transfer of the modeling technology has not kept pace with the development and demands of the computational fluid dynamics (CFD) tools. An examination of the process of model development leads to recommendations for a mid-course correction involving close coordination between modelers, CFD developers, and application engineers. In instances where the old process is changed and cooperation enhanced, timely transfer is realized. A turbulence modeling information database is proposed to refine the process and open it to greater participation among modeling and CFD practitioners.

Marvin, Joseph G.↗

NASA NTRSDate not supplied

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

NASA NTRSDate not supplied

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

NASA NTRS1990

Design and validation of advanced transonic wings using CFD and very high Reynolds number wind tunnel testing

A study is presented that opens the possibility for further wing aerodynamic technology advances when the test and design environment is at a significantly higher Reynolds number than that used for previous generations of commercial transports. Early generation wings were based primarily on NACA airfoil sections integrated simply into three-dimensional designs. Recently, designs have been developed with a major influence from CFD and have depended less on iterative wind tunnel testing. It is shown that, coupled with improvements in CFD wing modeling and advances in test techniques, additional improvements in wing technology can be realized at significantly higher Reynolds numbers.

Goldhammer, Mark I.↗

NASA NTRS1991

Numerical study of external burning flowfields

This paper demonstrates the successful application of CFD to modeling an external burning flowfield. The study used the 2D, 3D, and PNS versions of the SPARK code. Various grids, boundary conditions, and ignition methodologies have been employed. Flameholding was achieved through the use of a subsonic outflow condition and a hot block located behind the step to ignite the fuel. Since the resulting burning produces a large subsonic region downstream of the cowl, this entire surface can be pressurized to the level of the back pressure. An evaluation of interactions between the ramjet exhaust and the external burning products demonstrate the complexity of this design issue. Ths code is now capable of evaluating the external burning effectiveness for flight vehicles using simple injector schemes, and the methodology can be readily applied to other external burning designs.

Bittner, Robert D.↗

NASA NTRS1991

Group evaporation

Liquid fuel combustion process is greatly affected by the rate of droplet evaporation. The heat and mass exchanges between gas and liquid couple the dynamics of both phases in all aspects: mass, momentum, and energy. Correct prediction of the evaporation rate is therefore a key issue in engineering design of liquid combustion devices. Current analytical tools for characterizing the behavior of these devices are based on results from a single isolated droplet. Numerous experimental studies have challenged the applicability of these results in a dense spray. To account for the droplets' interaction in a dense spray, a number of theories have been developed in the past decade. Herein, two tasks are examined. One was to study how to implement the existing theoretical results, and the other was to explore the possibility of experimental verifications. The current theoretical results of group evaporation are given for a monodispersed cluster subject to adiabatic conditions. The time evolution of the fluid mechanic and thermodynamic behavior in this cluster is derived. The results given are not in the form of a subscale model for CFD codes.

Shen, Hayley H.↗

NASA NTRS1992

Workshop on Grid Generation and Related Areas

A collection of papers given at the Workshop on Grid Generation and Related Areas is presented. The purpose of this workshop was to assemble engineers and scientists who are currently working on grid generation for computational fluid dynamics (CFD), surface modeling, and related areas. The objectives were to provide an informal forum on grid generation and related topics, to assess user experience, to identify needs, and to help promote synergy among engineers and scientists working in this area. The workshop consisted of four sessions representative of grid generation and surface modeling research and application within NASA LeRC. Each session contained presentations and an open discussion period.

Source record↗

NASA NTRS1995

Center for Modeling of Turbulence and Transition: Research Briefs, 1995

This research brief contains the progress reports of the research staff of the Center for Modeling of Turbulence and Transition (CMOTT) from July 1993 to July 1995. It also constitutes a progress report to the Institute of Computational Mechanics in Propulsion located at the Ohio Aerospace Institute and the Lewis Research Center. CMOTT has been in existence for about four years. In the first three years, its main activities were to develop and validate turbulence and combustion models for propulsion systems, in an effort to remove the deficiencies of existing models. Three workshops on computational turbulence modeling were held at LeRC (1991, 1993, 1994). At present, CMOTT is integrating the CMOTT developed/improved models into CFD tools which can be used by the propulsion systems community. This activity has resulted in an increased collaboration with the Lewis CFD researchers.

Source record↗

NASA NTRS1998

Liquid Motion in a Rotating Tank Experiment (LME)

The Liquid Motion Experiment (LME), which flew on STS 84 in May 1997, was an investigation of liquid motions in spinning, nutating tanks. LME was designed to quantify the effects of such liquid motions on the stability of spinning spacecraft, which are known to be adversely affected by the energy dissipated by the liquid motions. The LME hardware was essentially a spin table which could be forced to nutate at specified frequencies at a constant cone angle, independently of the spin rate. Cylindrical and spherical test tanks, partially filled with liquids of different viscosities, were located at the periphery of the spin table to simulate a spacecraft with off-axis propellant tanks; one set of tanks contained generic propellant management devices (PMDs). The primary quantitative data from the flight tests were the liquid-induced torques exerted on the tanks about radial and tangential axes through the center of the tank. Visual recordings of the liquid oscillations also provided qualitative information. The flight program incorporated two types of tests: sine sweep tests, in which the spin rate was held constant and the nutation frequency varied over a wide range; and sine dwell test, in which both the spin rate and the nutation frequency were held constant. The sine sweep tests were meant to investigate all the prominent liquid resonant oscillations and the damping of the resonances, and the sine dwell tests were meant to quantify the viscous energy dissipation rate of the liquid oscillations for steady state conditions. The LME flight data were compared to analytical results obtained from two companion IR&D programs at Southwest Research Institute. The comparisons indicated that the models predicted the observed liquid resonances, damping, and energy dissipation rates for many test conditions but not for all. It was concluded that improved models and CFD simulations are needed to resolve the differences. This work is ongoing under a current IR&D program.

Deffenbaugh, D. M.↗