Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CERIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Effect of Minor Ce Additions on Corrosion Behavior of Experimental Pipeline Steel

Minor additions of rare earth elements (REEs) have been shown to improve various steel properties. In particular, Cerium (Ce), as a relatively abundant and inexpensive element, has received attention as a potentially beneficial minor alloying addition for a variety of steel applications, including pipelines materials. The objective of this work is to investigate the effect of Ce on corrosion performance of experimental high-strength pipeline steel. Electrochemical corrosion experiments were carried out on steel without and with 0.006, 0.018, and 0.03 wt.% of Ce in 3.5 wt.% NaCl saturated with CO2 at 20 oC. For comparison purposes, X100 carbon steel specimens machined from an experimental pipe with a yield strength of 731 MPa were tested under the same conditions. The electrochemical techniques employed included: potentiodynamic polarization (PDP), linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS). In addition, post-corrosion surface characterization was performed using scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), while crystalline phases were determined by X-ray diffraction (XRD). The corrosion of base metal without Ce was lower (0.15 mm/y) compared to carbon steel X100 (0.9 mm/yr). The electrochemical results showed that adding Ce accelerates corrosion rates compared to base metal without Ce. No pitting corrosion of tested steel was detected.

Belarbi, Zineb↗

Gas-Phase Stability of Large Lanthanide:Ligand Clusters Evaluated Using Collision-Induced Dissociation

Introduction In the reprocessing of f-elements present in used nuclear fuels, a variety of diglycolamides (DGA’s) are used as extractants for actinide partitioning. In particular, the Actinide-Lanthanide Separation (ALSEP) process typically utilizes either the N,N,N’,N’-tetraoctyl diglycolamide (TODGA) or N,N,N',N'-tetra-2-ethylhexyl diglycolamide (T2EHDGA) extractant ligands following the partitioning of uranium and plutonium from used nuclear fuel. To better understand fundamental interactions in these processes, covalent bonding of several f-elements with diglycolamides, primarily TODGA, is investigated in the gas phase using nanospray ionization and a quadrupole time-of-flight mass spectrometer. Further, analysis of the identity and relative strength of the cluster is enabled by MS2 isolation and collision induced dissociation. Methods Metal ion cluster analysis was completed using a Bruker (Billerica, MA, USA) mircOTOF-Q II quadrupole time-of-flight mass spectrometer with a CaptiveSpray nanospray ion source. Detection was accomplished using positive ionization mode. Metal: ligand solutions were assembled as 30 µM europium nitrate, samarium nitrate, cerium nitrate, or holmium nitrate and 3 µM DGA in acetonitrile or a 50:50 mixture of acetonitrile: isopropanol. Preliminary data The samarium cluster experiments yielded clusters with a samarium:TODGA ratio of up to 1:7 able to be isolated and evidence of greater ratios present in the mass spectrum. This is surprising, as metal clusters are not expected to have a coordination space able to accommodate this many TODGA ligands, due to its size and tridenticity. Collisional activation of [Sm(TODGA)3]3+ suggested loss of a TODGA radical cation, in addition to ligand fragmentation. In contrast, activation of clusters with higher Sm:TODGA ratios resulted in loss of entire ligands, with no evidence of fragmentation. A lower collision energy was required to remove ligands as the number of bound TODGAs increased, suggesting that in larger clusters, ligands are more delicately complexed to the metal. In addition, several clusters were observed with the composition [Sm(NO3)x(TODGA)n x]+3 x. With a single nitrate ion, clusters with up to six TODGAs were able to be isolated. In a similar pattern to the samarium clusters containing only TODGA, less collision energy was required to eliminate one or more TODGAs with increasing size. Clusters with composition [Sm(NO3)(TODGA)n-1]2+ appeared in lower abundance and were more collisionally stable than [Sm(TODGA)n]3+ clusters. With two nitrate ions, only clusters with a single TODGA were able to be isolated. Analogous europium experiments resulted in similar clusters. Ratios of up to 1:7 Eu:TODGA and clusters with one nitrate and up to five TODGAs were isolated. In clusters with two nitrate ions, only one or two TODGAs were observed to be bound. Similar to samarium, MS2 experiments with the Eu clusters suggested that larger clusters required less collision energy to eliminate TODGA. Europium clusters with the composition [Eu(NO3)(TODGA)n-1]2+ were observed in greater abundance and with greater stability than the equivalent cluster with the composition [Eu(TODGA)n]3+. Novel Aspect These are the first reported Ln:TODGA clusters, allowing us to begin to investigate intrinsic complexation of lanthanides with process-relevant ligands.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High temperature electrical property measurements of ceramics

Emerging applications in energy and aerospace systems require high quality data on the high temperature electrical properties of ceramics, particularly oxides, to guide material selection, design, and modeling. This presentation demonstrates the functionality of a specially designed sample fixture that enables electrical measurements to be conducted up to temperatures as high as 1600°C. Utilizing the mismatch in the coefficient of thermal expansion between two materials, a purely mechanical method for establishing electrical contact in the van der Pauw geometry is used to measure the bulk resistivity of ceramic materials. Measurements conducted on a number of common high temperature materials will be presented, including 20 mol % Gd-doped cerium oxide. Measurements are performed using multiple techniques and compared to literature values finding excellent agreement. The approach described in this work enables the van der Pauw method to be applied to many ceramic materials over a wide range of temperatures and environments.

Cann, David P.↗

Piston for use in internal combustion engines and method of making the piston

An additive manufactured piston having a crown portion and a skirt portion form of an aluminum-cerium-silicon alloy. The piston includes a least one recess pocket in an unstressed region located at an interface between an inner surface of the crown portion and an outer surface of the skirt portion. The skirt portion includes an outer panel surface defining an external rib adjacent a peripheral end surface, at least one stiffening rib extending from a pin boss to a skirt end, and a wall thickness of between 0.2 mm and 1.0 mm in a region between the external rib and the at least one stiffening rib. The skirt portion further includes an internal first rib having a width W1 on a thrust side portion and an internal second rib having a width W2 located on an anti-thrust side portion, in which W1 is greater than W2.

Petrus, Ronald John↗

Mapping Rare Earths and Toxics in E-Waste via Hyperspectral Imaging and Machine Learning

Electronic waste (e-waste) presents a mounting challenge to environmental sustainability due to its complex composition, which includes high-value rare earth elements, hazardous organic compounds, and non-recyclable plastics. Accurate and scalable material classification is essential for enabling efficient resource recovery and safe recycling practices. This study introduces a confidence-aware classification pipeline that combines mid-infrared hyperspectral imaging (HSI), spectral angle mapping (SAM), and iterative machine learning to perform pixel-level material identification across e-waste devices. A curated spectral library encompassing artificial materials (e.g., plastic iron oxide, galvanized metals), minerals (e.g., allanite, hematite), and organic compounds (e.g., benzanthracene, toluene) was used to generate pseudo-labels, each assigned a confidence score based on SAM-derived spectral similarity. High-confidence samples from seven consumer electronics—digital cameras, keyboards, laptop fans, modems, motherboards, TV remotes, and speakers—were iteratively expanded and classified using models such as Support Vector Machine (SVM), Random Forest, Gradient Boosting Classifier, Partial Least Squares Discriminant Analysis (PLSDA) and Logistic Regression. The best-performing classifiers achieved macro F1 scores approaching 1.0. Results revealed widespread plastic content (dominated by plastic iron oxide), the presence of rare earth-bearing minerals like cerium-containing allanite, and pervasive detection of hazardous organics such as benzanthracene. Principal Component Analysis (PCA) visualizations and confusion matrices confirmed high separability and robust classification performance. This methodology enables precise, non-destructive, and scalable classification of heterogeneous e-waste streams. It supports automated, hazard-aware sorting in recycling workflows, facilitating selective recovery of critical materials and compliance with circular economy goals. The confidence-aware framework provides a foundation for real-time deployment in industrial settings, offering significant implications for smart e-recycling infrastructure and policy-driven material stewardship.

Circular economy↗

Development of Biological and Electrochemical Technologies for the Clean Extraction of Copper and Critical Materials from Low Grade Ores

As we transition toward renewable energy resources and electrification, there will be an increasing demand for critical materials, including copper. While copper is currently mined in the US, processing capacity is not sufficient, and intermediate mining products are shipped to Asia for further processing. The goal of this research was to develop a transformative hydrometallurgical process for the production of copper from low-grade ores that would eliminate the need for smelting and would increase the domestic processing capacity in the US, The project initially focused on the electrochemical reduction of copper concentrate using vanadium, followed by the biological oxidation to produce a stream compatible with existing solvent extraction and electrowinning operations. We discovered an efficient electrochemical process that could produce copper salts from concentrate without the need for biological oxidation, and this technology has been licensed and spun-off into a start-up company. The microbes involved in the current state-of-the-art bioleaching processes were genetically modified to introduced a number of new traits, including increased sulfur oxidation, salt-tolerance, and binding of other critical metals such as cobalt, molybdenum, rhenium, and the rare earth elements. The project was extended to also explore the electrochemical oxidation of copper concentrate using cerium which would potentially eliminate production of hydrogen sulfide that occurs with the reductive leaching process. This technology was found to have slower kinetics, however could it still be developed as an alternative process for domestic copper production and has been found to be applicable to other critical minerals.

42 ENGINEERING↗

Post-irradiation 1600°C Heating Test of AGR-1 UCO Fuel Kernels

Five bare kernels were selected from the U.S. Advanced Gas Reactor (AGR) 1 irradiation experiment Compact 5-3-1 to perform post-irradiation safety tests. The safety test involved heating the kernels in the Fuel Accident Condition Simulator (FACS) furnace in the inert atmosphere to a peak temperature of 1600°C and isothermally holding at this temperature for about 47 hours while collecting fission products released. This test was to assess the retention of fission products in bare kernels without the effects of the other TRISO layers (buffer, IPyC, SiC, and OPyC) or the graphitic matrix material. The bare kernels released nearly 100% of cesium and antimony, while they were able to maintain about 30% of europium, 50% of strontium, and the majority of cerium and ruthenium. In addition, about 48% of the calculated inventory of Kr-85 released during the test, indicating that kernels were capable of retaining a considerable fraction of fission gas K-85 during irradiation.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fast and bright scintillators for ultrafast materials dynamics using 4th generation synchrotron

We present recent advances in fast and bright scintillators for ultrafast X-ray phase contrast imaging of dynamic materials experiments at the upgraded Advanced Photon Source (APS-U), a fourth generation synchrotron. APS-U enables hard X-ray imaging at frame rates of at least 13 MHz (corresponding to 77 ns or shorter interframe intervals), creating a new need for scintillators with faster response and higher light output than lutetium yttrium oxyorthosilicate (LYSO). For indirect imaging and diffraction with ultrafast cameras, commercial lanthanum bromide (LaBr3) and cerium bromide (CeBr3) are promising candidates. These materials exhibit decay times approximately a factor of two shorter than LYSO (around 40 ns) and lutetium oxyorthosilicate (LSO), while maintaining comparable light yield per incident X-ray photon. However, their implementation at APS-U requires addressing several challenges, including material limitations due to hygroscopicity, efficient optical coupling to imaging systems, and high quantum efficiency for conversion of scintillation light, predominantly at wavelengths below 400 nm, into detectable electronic signals. We report results from material characterization, detector integration and packaging, and beamline experiments of materials with impact. In addition, emerging scintillator classes, including perovskites and high-entropy materials, are discussed as potential alternatives for next-generation ultrafast X-ray diagnostics.

Wang, Zhehui [Los Alamos] (ORCID:0000000178264063)↗

Engineering of Grain Boundaries in CeO 2 Enabling Tailorable Resistive Switching Properties

Abstract Defect engineering in valence change memories aimed at tuning the concentration and transport of oxygen vacancies are studied extensively, however mostly focusing on contribution from individual extended defects such as single dislocations and grain boundaries. In this work, the impact of engineering large numbers of grain boundaries on resistive switching mechanisms and performances is investigated. Three different grain morphologies, that is, “random network,” “columnar scaffold,” and “island‐like,” are realized in CeO 2 thin films. The devices with the three grain morphologies demonstrate vastly different resistive switching behaviors. The best overall resistive switching performance is shown in the devices with “columnar scaffold” morphology, where the vertical grain boundaries extending through the film facilitate the generation of oxygen vacancies as well as their migration under external bias. The observation of both interfacial and filamentary switching modes only in the devices with a “columnar scaffold” morphology further confirms the contribution from grain boundaries. In contrast, the “random network” or “island‐like” structures result in excessive or insufficient oxygen vacancy concentration migration paths. The research provides design guidelines for grain boundary engineering of oxide‐based resistive switching materials to tune the resistive switching performances for memory and neuromorphic computing applications.

36 MATERIALS SCIENCE↗

Ce IV 70 oxosulfate rings, frameworks, supramolecular assembly and redox activity

M IV molecular oxo-clusters (M=Zr, Hf, Ce, Th, U, Np, Pu) are prolific in bottoms-up material design, catalysis, and elucidating reaction pathways in nature and in synthesis. Here we introduce Ce 70 , a wheel-shaped oxo-cluster, [Ce IV 70 -(OH) 36 (O) 64 (SO 4 ) 60 (H 2 O) 10 ] 4- . Ce 70 crystallizes into intricate high pore volume frameworks with divalent transition metals and Ce-monomer linkers. Eight crystal-structures feature four framework types in which the Ce 70 -rings are linked as propellers, in offset-stacks, in a tartan pattern, and as isolated rings. In this work, small-angle X-ray scattering of Ce 70 dissolved in butylamine, with and without added cations (Ce IV , alkaline earths, Mn II ), shows the metals‘ differentiating roles in ring linking, leading to supramolecular assemblies. The large acidic pores and abundant terminal sulfates provide ion-exchange behavior, demonstrated with U IV and Nd III . Frameworks featuring Ce III/IV -monomer linkers demonstrate both oxidation and reduction. Furthermore, this study opens the door to mixed-metal, highly porous framework catalysts, and new clusters for metal-organic framework design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineering PdAu/CeO 2 Alloy/Oxide Interfaces for Selective Methane‐to‐Methanol Conversion with Water

The direct conversion of methane-to-methanol remains a critical challenge in methane valorization. In this study, we unveil the crucial role of PdAu/CeO 2 catalysts in enabling selective methane transformation under mild conditions, using only water as the sole oxidant. Through a combination of experimental techniques, including XPS and catalytic testing, alongside density functional theory (DFT) calculations, we demonstrate that a Pd 0.3 Au 0.7 /CeO 2 catalyst, which predominantly exposes isolated Pd atoms, achieves remarkable methanol selectivity (∼80%) at 500 K with a 1:1 methane-to-water ratio. While Pd/CeO 2 efficiently activates methane, its tendency for overreaction leads to complete methanol decomposition, thereby limiting selectivity. Alloying Pd with Au on ceria mitigates this over-reactivity, preventing methanol degradation while maintaining sufficient catalytic activity. The PdAu/CeO 2 composite exhibits a synergistic effect: Pd in contact with the ceria support facilitates methane activation and water dissociation, while Au fine-tunes reactivity to promote methanol formation. DFT calculations confirm that isolated Pd sites at the PdAu/CeO 2 interface play a key role in balancing activity and selectivity. This work underscores the importance of alloy/oxide interfaces in controlling selective methane conversion with water and offers valuable insights for designing highly efficient catalysts for methanol synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of a Pressurized Water Treatment on Internal Gelation Sol-Gel Microspheres

Based on previous observations that a pressurized water treatment (PWT) prevented cracking of sol-gel microspheres, we investigated the effects of a PWT on microsphere crystallinity, density, and specific surface area (SSA). Results were used to determine how a PWT alters the properties of microspheres upon drying and heating. Microspheres with diameters near 100-200 µm were prepared with and without a PWT and measured using x-ray diffraction (XRD), transmission electron microscopy (TEM), nitrogen adsorption (BET), and pycnometry. Properties of air-dried microspheres processed with and without a PWT are compared. Additionally, the properties of microspheres processed using a PWT are reported after heating to 150 °C, 450 °C, 750 °C, 1050 °C, and 1350 °C. X-ray diffraction measurements indicate that the PWT step improves the crystallinity of air-dried microspheres. XRD data was also used to calculate crystallite size, which increases with higher heat treatment temperatures. TEM images support crystallite size calculations from XRD data and provide an indication of the range of crystallite sizes, particularly for samples processed at higher temperatures where crystallite sizes are too large for estimation using the Scherrer formula. Density and SSA measurements performed as a function of heat treatment temperature indicate that a PWT increases the density of air-dried microspheres, creates a pore network, and that significant densification occurs between 450 - 750 °C. These results may be used to inform decisions on internal gelation flowsheet parameters to optimize the microsphere formation and gelation step, prevent microsphere cracking, and produce microspheres suitable for subsequent coating operations or pressing into pellets.

cerium oxide, TRISO, internal gelation, nuclear fu↗

The Ce-Fe-Ti System: Phase Equilibria in the Fe-rich Corner at 1000 °C

The rare earth–iron–transition metal systems are of increasing interest in the search for novel permanent magnet phases. This work reports on the solidification behavior, phase equilibria and stability range of solid phases in the ternary Ce-Fe-Ti system, focusing on the iron-rich region (> 65 at.% Fe) of the isothermal section at 1000 °C. Further, two ternary phases Ce 1.03 Fe 12-x Ti x (x = 0.87–1.02) with ThMn 12 structure type and Ce 3.06 Fe 27.6 Ti 1.4 with Nd 3 Fe 29 structure type were observed. Magnetic measurements of Ce 1.03 Fe 12-x Ti x and Ce 3.06 Fe 27.6 Ti 1.4 revealed ferromagnetic ordering with Curie temperatures of 550 K and 327 K, respectively.

36 MATERIALS SCIENCE↗

Efficient transfer hydrodehalogenation of halophenols catalyzed by Pd supported on ceria

We report the transfer hydrodehalogenation (THD) of halophenols is efficiently catalyzed by palladium supported on high surface area ceria (Pd/CeO 2 ) under mild conditions (65 °C) using isopropanol (iPrOH) as hydrogen source. The reactivity of 4-halophenols (4-X-PhOH) varies in the order 4-F-PhOH > 4-Cl-PhOH > 4-Br-PhOH > > 4-I-PhOH and appears to be controlled by the desorption of halides from the catalyst surface. Kinetic analysis of the reactions and temperature programmed surface reaction (TPSR) experiments indicate that oxidative addition of C-X bonds and H-abstraction from isopropoxide compete for the same active sites on Pd. The catalyst was able to conduct the THD of various hazardous pollutants and emerging contaminants (dichlorodiphenyltrichloroethane (DDT), pentachlorophenol, pentafluorophenol and triclosan).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Intuitive study on the effect of support morphology over Cs-Ru/CeO 2 catalyst for microwave-initiated ammonia synthesis

Microwave-initiated ammonia synthesis is a potential candidate to the current Haber-Bosch process that can operate from stranded renewable energy source. Our previous studies indicated Cs-Ru/CeO 2 is a promising catalyst for microwave-assisted ammonia synthesis and the morphology of CeO 2 significantly affects the catalytic performance. In this paper, CeO 2 support with distinct morphologies nanorod, nanoparticle, and microstructure, is studied comprehensively at ambient pressure and low temperature under microwave irradiation. Moreover, CeO 2 nanorods of various sizes were synthesized at different timing (24, 36, and 48 h). Nanorods synthesized at 36 h exhibited superior activity associated to high dispersion and small Ru particle size.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The solubility and speciation of REE phosphate endmembers (CePO 4 and YPO 4 ) in Cl-rich aqueous fluids from 350 to 450 °C and implications for natural systems

The rare earth elements (REE) are important metals used increasingly in advanced technologies. Within the crust, the elements Ce and Y are commonly more abundant compared to other lanthanides and comprise important end-member constituents of REE-bearing minerals. Specifically, Ce is part of the light (L) REE which have larger ionic radii than the heavy (H) REE, which are grouped together with Y. These differences in ionic radius can lead to important physico-chemical trends within the lanthanide group. Despite a recent increase in experimental and thermodynamic data for the REE at high temperature and pressure, there is still a significant lack of these data at supercritical conditions. In this study we conducted batch-type experiments to measure the solubility of REE phosphates (CePO 4 and YPO 4 ) at varying starting pH (1.5–10), and salinity (0.01–1.4 mol/kg NaCl) at 350 and P sat , and from 400 to 450 °C at 700 bar. Results show that the solubility of Ce (33–0.14 ppb) is generally higher than Y (13–0.13 ppb) and that Ce complexes more strongly with both chloride and hydroxyl ligands compared to Y. The solubilities of both REE phosphates are highly pH-dependent and, to a lesser extent, depend on salinity at the studied conditions. The solubility data from this study were implemented into the GEMSFITS program to optimize the thermodynamic properties of Ce and Y hydroxyl and chloride species. The updated standard partial molal Gibbs energies of formation (Δ f G 0 T,P ) are used within the experimental temperature and pressure range to accurately predict the CePO 4 and YPO 4 solubility and Ce and Y speciation behavior. Based on the updated thermodynamic properties we also provide formation constants (log β n Cl,OH ) for Ce and Y hydroxyl and chloride species. Updated thermodynamic properties are applied to model REE-apatite dissolution and REE mobility based on the Pea Ridge iron oxide apatite deposit in Missouri, USA. The apatite dissolution model replicates natural observations including the replacement of monazite and xenotime after apatite and is an example of the utility of the new thermodynamic constants applied to supercritical crustal fluids. Furthermore, the findings of this study advance the predictive capabilities of geochemical models, our understanding of the behavior of individual REE, and permit modeling the overarching fractionation trends between LREE and HREE in supercritical crustal fluids.

58 GEOSCIENCES↗

Modeling the performance and faradaic efficiency of solid oxide electrolysis cells using doped barium zirconate perovskite electrolytes

Y-doped BaZrO 3 (BaZr 1 x Y x O 3 δ , or “BZY”), a proton-conducting ceramic featuring high bulk conductivity and good chemical stability, is a promising electrolyte material for solid oxide electrolysis cells. Further doping with Ce and/or Yb (creating materials “BCZY” and “BCZYYb”) can improve conductivity and sintering properties, but at significant penalty to cells’ faradaic efficiency (FE). Studies have proposed that reduction of lattice Ce can occur in the hydrogen electrode, which consumes some hydrogen produced by the hydrogen evolution reaction, leading to decreased FE. Despite studies suggesting this phenomenon, the mechanism is largely unknown. In this work, we developed a multiphysics model to study the transport of multiple defect species and the performance of BZY, BCZY, and BCZYYb, capturing the tradeoff between enhanced performance at the cost of FE for BCZY and BCZYYb electrolytes compared to BZY. We also found that increasing the water content of the anode gas supply lowers the current output of the cell but results in better FE. The model, which uses several parameters previously unavailable in the literature, was validated to experiments varying temperature, steam water content, and electrolyte material, as well as two performance metrics (performance curves and FE). Results verify and explain observed trends, informing future work on Ce-doped BZY electrolytes.

08 HYDROGEN↗

Investigating the failure behavior of cast Al-11Ce-0.4Mg alloys using in-situ scanning electron microscopy tensile testing

Within the last decade, research on Al-Ce-Mg alloys has reported promising results for use in cast part applications. In this paper, the failure behavior of cast Al-11Ce-0.4Mg (wt%) was investigated experimentally with focus on the effect the matrix and intermetallic phases have on the fracture propagation behavior at failure. For the first time, in-situ SEM tensile testing was used to study the failure behavior of cast Al-Ce alloys, reporting results for uniaxial, DIC, and single edge notch tensile tests. The results of the in-situ SEM tensile testing were compared with the materials characterization experiments, which included serial sectioning, EBSD, EDS, and fractography. Analysis of EBSD and EDS mapping of cast Al-11Ce-0.4Mg showed that the cast microstructure was a hypereutectic two phase Al-Ce alloy with grains encompassing large complex colonies of laminar eutectic Al 11 Ce 3 intermetallic. The uniaxial tensile results reported the effect casting defects have on the strength and ductility of the alloy, and DIC in-situ testing showed that the eutectic colonies plastically deform less than the matrix phase. In-situ SEM single edge notch tensile testing displayed how the strength of an individual phase affected the crack propagation direction in the alloy. The results of both the materials characterization and in-situ tensile testing experiments on the failure of this alloy revealed further directions for future alloy development that can improve both the strength and fracture toughness of Al-Ce-Mg alloys.

36 MATERIALS SCIENCE↗