Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alloy Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

A stress-sensitive precipitate nucleation model beyond classical nucleation theory

The dynamic evolution of precipitates and second phases dictates the strength and stability of most engineering alloys. By design, or as a consequence of thermo-mechanical aging, engineering metals and alloys often form precipitates of second phases when subjecting to diverse thermal and mechanical loads. Precipitation is governed by several factors, including the alloy’s composition, processing/operating temperature, and stresses — either as a result of external loads or from residual stresses. However, state-of-the-art models for precipitate nucleation (i.e., classical nucleation theory) typically lacks consistent method to capture the effects of externally applied and/or internal stresses on nucleation; thereby severely limiting the applicability of these models to complex materials systems and to representative loading scenarios. Here, in this work, we extend upon classical nucleation theory to account for the effect of stresses on precipitation kinetics and thermodynamics. This is achieved via the use of an Eshelbian micromechanics framework keeping track of (i) the stress build up resulting from second phase formation as a function of mechanical load and, (ii) the effects of dislocations on precipitate formation. This new model is applied to σ precipitate in Fe–Cr binary alloys and M 23 C 6 precipitate in 316H stainless steel (SS). Simulations demonstrate the important role of both the remotely applied loads and dislocation pile ups on precipitate nucleation.

36 MATERIALS SCIENCE↗

The corrosion performance of die-cast magnesium alloy MRI230D in 3.5% NaCl solution saturated with Mg(OH){sub 2}

The environmental behavior of die-cast magnesium alloy MRI230D designated for high-temperature applications was evaluated in comparison with regular AZ91D alloy. The microstructure examination was carried out using SEM, TEM, and X-ray diffraction analysis; the corrosion performance in 3.5% NaCl solution was evaluated by immersion test, salt spray testing, potentiodynamic polarization analysis, and stress corrosion behavior by Slow Strain Rate Testing (SSRT). Although the general corrosion resistance of MRI230D was slightly improved compared to that of AZ91D alloy its stress corrosion resistance was relatively reduced. The variations in the environmental behavior of the two alloys were mainly due to the differences in their chemical composition and microstructure after die casting. In particular, the differences were related to the reduced Al content in MRI230D and the addition of Ca to this alloy, which consequently affected its relative microstructure and electrochemical characteristics. - Research Highlights: {yields}Corrosion and SCC resistance of a new Mg alloy MRI230D was evaluated vs. regular AZ91D. {yields}MRI230D has a minor advantage in corrosion performance compared with AZ91D. {yields}The SCC resistance of MRI230D by SSRT analysis was relatively reduced. {yields}The reduced SCC resistance of MRI230D was due to the detrimental effect of Ca on ductility.

36 MATERIALS SCIENCE↗

Crystal Viscoplasticity Model of Molybdenum Including the Influence of Silicon in Solid Solution [Crystal Viscoplasticity Model of Mo Including the Influence of Si in Solid Solution]

Molybdenum (Mo)-based alloys offer higher temperature capability than nickel-based superalloys. The challenge of designing these alloys is tailoring the chemistry and microstructure to achieve high-temperature strength, creep and fatigue resistance, and oxidation resistance while maintaining lower-temperature ductility and damage tolerance. Structure-properties modeling tools can be used to identify optimum microstructures. However, one missing element in this tool set is a constitutive model for the more ductile α-Mo phase over the entire temperature range from room temperature to 1,400°C. A crystal viscoplasticity model is developed for α-Mo, including the influence of varying amounts of silicon (Si) in solid solution. As a result, the temperature, strain rate, and Si dependence of the deformation behavior needed to determine the model parameters are obtained from new compression experiments.

36 MATERIALS SCIENCE↗

Toward the design of ultrahigh-entropy alloys via mining six million texts

Abstract It has long been a norm that researchers extract knowledge from literature to design materials. However, the avalanche of publications makes the norm challenging to follow. Text mining (TM) is efficient in extracting information from corpora. Still, it cannot discover materials not present in the corpora, hindering its broader applications in exploring novel materials, such as high-entropy alloys (HEAs). Here we introduce a concept of “context similarity" for selecting chemical elements for HEAs, based on TM models that analyze the abstracts of 6.4 million papers. The method captures the similarity of chemical elements in the context used by scientists. It overcomes the limitations of TM and identifies the Cantor and Senkov HEAs. We demonstrate its screening capability for six- and seven-component lightweight HEAs by finding nearly 500 promising alloys out of 2.6 million candidates. The method thus brings an approach to the development of ultrahigh-entropy alloys and multicomponent materials.

36 MATERIALS SCIENCE↗

Preliminary neutronics design of china lead-alloy cooled demonstration reactor (CLEAR-III) for nuclear waste transmutation

China Lead-Alloy cooled Demonstration Reactor (CLEAR-III), which is the concept of lead-bismuth cooled accelerator driven sub-critical reactor for nuclear waste transmutation, was proposed and designed by FDS team in China. In this study, preliminary neutronics design studies have primarily focused on three important performance parameters including Transmutation Support Ratio (TSR), effective multiplication factor and blanket thermal power. The constraint parameters, such as power peaking factor and initial TRU loading, were also considered. In the specific design, uranium-free metallic dispersion fuel of (TRU-Zr)-Zr was used as one of the CLEAR-III fuel types and the ratio between MA and Pu was adjusted to maximize transmutation ratio. In addition, three different fuel zones differing in the TRU fraction of the fuel were respectively employed for this subcritical reactor, and the zone sizes and TRU fractions were determined such that the linear powers of these zones were close to each other. The neutronics calculations and analyses were performed by using Multi-Functional 4D Neutronics Simulation System named VisualBUS and nuclear data library HENDL (Hybrid Evaluated Nuclear Data Library). In the preliminary design, the maximum TSRLLMA was {approx}11 and the blanket thermal power was {approx}1000 MW when the effective multiplication factor was 0.98. The results showed that good performance of transmutation could be achieved based on the subcritical reactor loaded with uranium-free fuel. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Design and fabrication of a super alloy thermal protection system

A lightweight metallic TPS was designed, and two test articles were fabricated, one from Haynes 188 and one from Rene 41. A baseline TPS concept, selected at the beginning of the program, consisted of a Haynes 25 corrugation-stiffened beaded skin surface panel, a specially designed support system, and an insulation system. By optimizing the structure for the design loads and by chem-milling to remove material not needed, the mass of the baseline surface panel was reduced 25%, and the mass of the support structure was reduced 50%. The insulation system mass was reduced 40% by using two types of insulation, each suited to its temperature range, and by eliminating a foul bag which encapsulated the baseline insulation system. These reductions resulted in an overall 35% reduction in mass of the Haynes 188 panel from the baseline Haynes 25 design. Similar reductions were achieved with the Rene 41 system.

Varisco, A.↗

Room temperature creep in metals and alloys

Time dependent deformation in the form of creep and stress relaxation is not often considered a factor when designing structural alloy parts for use at room temperature. However, creep and stress relaxation do occur at room temperature (0.09-0.21 T m for alloys in this report) in structural alloys. This report will summarize the available literature on room temperature creep, present creep data collected on various structural alloys, and finally compare the acquired data to equations used in the literature to model creep behavior. Based on evidence from the literature and fitting of various equations, the mechanism which causes room temperature creep is found to include dislocation generation as well as exhaustion.

36 MATERIALS SCIENCE↗

The Analysis of the General Performance and Mechanical Behavior of Unirradiated FeCrAl Alloys Before and After Welding

The present report summarizes and discusses the preliminary results for the in-depth characterization of the modern, nuclear-grade FeCrAl alloys currently under development. The alloys were designed for enhanced radiation tolerance and weldability, and the research is currently being pursued by the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Last year, seven candidate FeCrAl alloys with well-controlled chemistry and microstructures were designed and produced; welding was performed under well-controlled conditions. The structure and general performance of unirradiated alloys were assessed using standardized and advanced microstructural characterization techniques and mechanical testing. The primary objective is to identify the best candidate alloy, or at a minimum to identify the contributing factors that increase the weldability and radiation tolerance of FeCrAl alloys, therefore enabling future generations of FeCrAl alloys to deliver better performance parameters. This report is structured so as to describe these critical assessments of the weldability; radiation tolerance will be reported on in later reports from this program.

36 MATERIALS SCIENCE↗

Design of Novel Precipitate-Strengthened Al-Co-Cr-Fe-Nb-Ni High-Entropy Superalloys

Here, a series of non-equiatomic Al-Co-Cr-Fe-Nb-Ni high-entropy alloys, with varying levels of Co, Nb and Fe, were investigated in an effort to obtain microstructures similar to conventional Ni-based superalloys. Elevated levels of Co were observed to significantly decrease the solvus temperature of the γ' precipitates. Both Nb and Co in excessive concentrations promoted the formation of Laves and NiAl phases that formed either during solidification and remained undissolved during homogenization or upon high-temperature aging. Lowering the content of Nb, Co, or Fe prevented the formation of the eutectic type Laves. In addition, lowering the Co content resulted in a higher number density and volume fraction of the γ' precipitates, while increasing the Fe content led to the destabilization of the γ' precipitates. Various aging treatments were performed which led to different size distributions of the strengthening phase. Results from the microstructural characterization and hardness property assessments of these high-entropy alloys were compared to a commercial, high-strength Ni-based superalloy RR1000. Potentially, precipitation-strengthened high-entropy alloys could find applications replacing Ni-based superalloys as structural materials in power generation applications.

36 MATERIALS SCIENCE↗

Proposed Material Properties, Allowable Stresses, and Design Curves of Diffusion Bonded Alloy 800H for the ASME Code Section III Division 5

Abstract Increased interest in compact heat exchangers (CHXs) to serve as intermediate heat exchangers of very high temperature reactors resulted in significant research and development on their design, analysis, and construction. Printed circuit heat exchangers are a type of CHXs with high thermal efficiency and compactness achieved through diffusion bonding a stack of etched plates with millimeter scaled channels. The diffusion bonding process changes the microstructural and mechanical properties of the wrought metal plates. The current nonnuclear design code ASME section VIII, division 1 captures the material property change through a “joint efficiency factor.” However, the current nuclear design code ASME section III, division 5 does not address or support the diffusion bonded material properties. Hence, there is a need to develop allowable stresses, isochronous curves, and fatigue life curves for various diffusion bonded alloys. In this study, Alloy 800H material was selected to establish the diffusion bonded material properties under tension, creep, fatigue, and creep-fatigue loads at elevated temperatures in the range 550–760 °C. A set of tests on diffusion bonded Alloy 800H (DB 800H) were performed and the acquired data are used in developing allowable stresses Sy, Su, Sr, Sm, St, Smt, So, isochronous curves and fatigue life curves according to the ASME section III, division 5 requirements. This paper also presents detailed procedures used in developing the ASME code section III division 5 design provisions for diffusion bonded Alloy 800H.

Engineering↗

Dynamic Atom Clusters on AuCu Nanoparticle Surface During CO Oxidation

Supported alloy nanoparticles are prevailing alternative low-cost catalysts for both heterogeneous and electrochemical catalytic processes. Selective interaction of an alloy component with a specific reactant induces a dynamic structural change of alloy nanoparticles under reaction conditions and largely controls their catalytic properties. However, such a multi-component dynamic-interaction-controlled evolution, both structural and chemical, remains far from clear. Herein, by using state-of-the-art environmental TEM, we directly visualize, in-situ at the atomic scale, the evolution of an AuCu alloy nanoparticle supported on CeO2 during CO oxidation. We find that gas molecules can “free” metal atoms on the {001} surface and form highly mobile atom clusters. Remarkably, we discover that CO exposure induces Au segregation and activation on nanoparticle surface, while O2 exposure leads to the segregation and oxidation of Cu on the particle surface. The as-formed Cu2O/AuCu interface may facilitate CO-O interaction corroborated by DFT calculations. These findings provide insights into the atomistic mechanisms on alloy nanoparticles during catalytic CO oxidation reaction, and to a broad scope of rational design of alloy nanoparticle catalysts.

Luo, Langli↗

Data-driven design of novel halide perovskite alloys

The great tunability of the properties of halide perovskites presents new opportunities for optoelectronic applications as well as significant challenges associated with exploring combinatorial chemical spaces. Here, in this work, we develop a framework powered by high-throughput computations and machine learning for the design and prediction of mixed cation halide perovskite alloys. In a chemical space of ABX 3 perovskites with a selected set of options for A, B, and X species, pseudo-cubic structures with B-site mixing are simulated using density functional theory (DFT) and several properties are computed, including stability, lattice constant, band gap, vacancy formation energy, refractive index, and optical absorption spectrum, using both semi-local and hybrid functionals. Neural networks (NN) are used to train predictive models for every property using tabulated elemental properties of A, B, and X site species as descriptors. Starting from a DFT dataset of 229 points, we use the trained NN models to predict the structural, energetic, electronic, and optical properties of an extensive dataset of 17955 compounds, and perform high-throughput screening in terms of stability, band gap, and defect tolerance, to obtain 392 promising compounds that are ranked as potential absorbers according to their photovoltaic figure of merit. Compositional trends in the screened set of attractive mixed cation halide perovskites are revealed and additional computations are performed on selected compounds. The data-driven design framework developed here is promising for designing novel mixed compositions and can be extended to a wider perovskite chemical space in terms of A, B, and X species, different kinds of mixing at the A, B, or X sites, non-cubic phases, and other properties of interest.

36 MATERIALS SCIENCE↗

High-entropy Al 0.3 CoCrFeNi alloy fibers with high tensile strength and ductility at ambient and cryogenic temperatures

High-entropy alloys (HEAs) are multi-component systems based on novel alloy composition designs with entropy maximization. They feature an array of unique mechanical properties when compared with traditional alloys. In this study, HEA fibers with diameters ranging from 1 to 3.15 mm in diameter, with the composition of Al 0.3 CoCrFeNi (atomic percent, at.%), were successfully fabricated by hot-drawing, followed by microstructural characterization using scanning-electron microscopy (SEM) and transmission-electron microscopy (TEM). The compositional variations within and between fibers were determined using energy-dispersive X-ray spectroscopy in TEM along with atomic-probe tomography (APT). These analyses revealed a homogeneous face-centered cubic (FCC) structure in the as-cast material, while post processing (e.g., forging and wire drawing) produced nanosized B2 particles in an FCC matrix. Electron back-scatter diffraction (EBSD) was used to determine the evolution of the texture and grain boundary character after processing of the fibers. The tensile strength and plasticity of the fibers were determined at both 298 K (1207 MPa/7.8%) and 77 K (1600 MPa/17.5%). Detailed TEM analyses revealed that the improvement of mechanical properties at 77 K (i.e. increased strength and ductility) is due to a change in deformation mechanisms from the planar slip of dislocations to nano-twinning. Such properties could be beneficial for cryogenic applications.

36 MATERIALS SCIENCE↗

Microstructural evolution of single Ni 2 TiAl or hierarchical NiAl/Ni 2 TiAl precipitates in Fe-Ni-Al-Cr-Ti ferritic alloys during thermal treatment for elevated-temperature applications

Precipitate features, such as the size, morphology, and distribution, are important parameters determining the mechanical properties of semi- or fully-coherent precipitatehardened alloys at elevated temperatures. In this study, the microstructural formation and evolution of recently-developed Fe-Ni-Al-Cr-Ti alloys with superior creep resistance have been systematically investigated using transmission-electron microscopy (TEM), scanning-electron microscopy (SEM), and atom-probe tomography (APT). These alloys were designed by adding 2 or 4 weight percent (wt. %) Ti into a NiAl-hardened ferritic alloy with a nominal composition of Fe-6.5Al-10Cr-10Ni-3.4Mo-0.25Zr-0.005B in wt. %. These alloys were, then, subjected to a homogenization treatment at 1,473 K for 0.5 hour, followed by aging treatments at 973 K for 1 ~ 500 hours. In the homogenization-treated case, both alloys contain a primary L21-type Ni 2 TiAl precipitate, but with the distinct size and morphology of the precipitates and precipitate/matrix interface structures. In the subsequent aging treatments, the 2 wt. % Ti alloy establishes a hierarchical-precipitate structure consisting of a fine network of a B2-type NiAl phase within the parent L2 1 -type Ni2TiAl precipitate, while the 4 wt. % Ti alloy retains the single Ni 2 TiAl precipitate. It was found that the hierarchical structure is more effective in remaining the coherent interface during the growth/coarsening of the precipitate. The formation of the different types of the precipitates, and their effects on the microstructural evolution are discussed, and the driving forces for these features are identified from the competition between the interface energy and elastic interactions due to the lattice misfit and misfit dislocations.

36 MATERIALS SCIENCE↗

Improved creep performance of CoCrFeNi high entropy alloys by Mo addition

The CoCrFeNi family of high entropy alloys has good mechanical and corrosion properties, performing like stainless steels with low yield stresses. They could, however, benefit from hardening methods for structural and high temperature applications. Here, this work investigates the potential for the CoCrFeNi alloy to be hardened with the addition of Mo. A series of CoCrFeNiMo alloys and their CoCrFeNi counterparts were subsequently manufactured at NETL and then mechanically creep tested at 650°C. The alloys were designed to possess a range of stacking fault energies which influence the mechanical properties of the alloys via the motion of their dislocations under stress. Results show that Mo-containing variants have creep rupture lives ranging from 4000 to 8000 hours, i.e., about two orders of magnitude longer than those for Mo-free variants. The significantly improved creep performance of the Mo-containing alloys is due to a combination of solid solution strengthening and precipitation strengthening from µ-phase and carbides.

36 MATERIALS SCIENCE↗

Design of high-strength refractory complex solid-solution alloys

Nickel-based superalloys and near-equiatomic high-entropy alloys containing molybdenum are known for higher temperature strength and corrosion resistance. Yet, complex solid-solution alloys offer a huge design space to tune for optimal properties at slightly reduced entropy. For refractory Mo-W-Ta-Ti-Zr, we showcase KKR electronic structure methods via the coherent-potential approximation to identify alloys over five-dimensional design space with improved mechanical properties and necessary global (formation enthalpy) and local (short-range order) stability. Deformation is modeled with classical molecular dynamic simulations, validated from our first-principle data. We predict complex solid-solution alloys of improved stability with greatly enhanced modulus of elasticity (3× at 300 K) over near-equiatomic cases, as validated experimentally, and with higher moduli above 500 K over commercial alloys (2.3× at 2000 K). We also show that optimal complex solid-solution alloys are not described well by classical potentials due to critical electronic effects.

36 MATERIALS SCIENCE↗

Rapid assessment of interfacial stabilization mechanisms of metastable precipitates to accelerate high-temperature Al-alloy development

Precipitate strengthened high-temperature alloys are currently used in safety-critical applications. Understanding precipitate stability and solute segregation mechanisms at high temperatures is key to designing high-strength alloys. Rapid in-situ approaches, therefore, are pivotal in accelerating the alloy design process. Hereby using the test case of a promising high-temperature Al-Cu-Mn-Zr alloy, we demonstrate the value of in-situ atom probe tomography coupled with in-situ transmission electron microscopy to reveal atomic-scale mechanisms that lead to the emergence of non-equilibrium solute segregation. Mn and Zr segregation at strengthening precipitate(θ’)-matrix interface increases the kinetic barrier for phase transformation thus retaining high-temperature strength.

36 MATERIALS SCIENCE↗

SU-F-T-505: A Novel Approach for Sparing Critical Organs at Risk for Cancer Patients Undergoing Radiation Oncology Treatments

Purpose: A major goal of an effective radiation treatment plan is to deliver the maximum dose to the tumor while minimizing radiation exposure to the surrounding normal structures. For example, due to the radiation exposure to neighboring critical structures during prostate cancer treatment, a significant increase in cancer risk was observed for the bladder (77%) and the rectum (105%) over the following decade. Consequently, an effective treatment plan necessitates limiting the exposure to such organs which can best be achieved by physically displacing the organ at-risk. The goal of this study is to present a prototype for an organ re-positioner device designed and fabricated to physically move the rectum away from the path of radiation beam during external beam and brachytherapy treatments. This device affords patient comfort and provides a fully controlled motion to safely relocate the rectum during treatment. Methods: The NiTi shape memory alloy was designed and optimized for manufacturing a rectal re-positioner device through cooling and heating the core alloy for its shaping. This has been achieved through a prototyped custom designed electronic circuit in order to induce the reversible austenitic transformation and was tested rigorously to ensure the integrity of the actuated motion in displacement of the target anatomy. Results: The desirable NiTi shape-setting was configured for easy insertion and based on anatomical constraint. When the final prototype was evaluated, accuracy and precision of the maximum displacement and temperature changes revealed that the device could safely be used within the target anatomy. Conclusion: The organ re-positioner device is a promising tool that can be implemented in clinical setting. It provides a controlled and safe displacement of the delicate organ(s) at risk. The location of the organ being treated could also be identified using conventional onboard imaging devices or MV imaging available on-board most modern clinical accelerators.

60 APPLIED LIFE SCIENCES↗