Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASSISTED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Phosphonate functionalized magnetic mesoporous silica for rare earth element recovery from citrate assisted solid waste extracts

The growing high demand of rare earth elements (REEs) has prompted extensive research on REE recovery from waste streams. This study reports the synthesis and evaluation of phosphonate-functionalized magnetic mesoporous silica (MMS-PP) for REE recovery from the acidic extracts of solid wastes. MMS-PP was synthesized using surfactant template and post-synthesis methods, and tested using simulated and real extraction solutions from citrate-assisted REE extracts from municipal solid waste incineration (MSWI) ash. The organic-inorganic hybrid MMS-PP was evaluated for La recovery from 50 mM simulated citrate extract, with the adsorption capacity of 13.5 mg/g compared to ∼2.5 mg/g for non-functionalized MMS. The MMS-PP material exhibited fast adsorption within 10 min, good La selectivity against competing Na + and Ca 2+ , moderate selectivity against Al 3+ and Fe 3+ , high recyclability over multiple adsorption-desorption cycles, and equivalent efficiency for La, Ce, Nd, and Y recovery. Furthermore, the MMS-PP material also demonstrated 70–95% REE recovery from real citrate extracts of MSWI ash, and the spent MMS-PP material can be regenerated and reused for multiple cycles. Functionalized mesoporous materials in combination with organic-ligand assisted extraction can potentially provide a green, effective, and tunable solid-liquid separation platform for REE recovery from complex solid waste streams.

REE recovery↗

Kinetics of low temperature plasma assisted NH 3 /H 2 oxidation in a nanosecond-pulsed discharge

Ammonia (NH 3 ) has been widely recognized as one of the carbon-neutral fuels. However, ammonia combustion suffers low reactivity and high N 2 O/NO x emissions. Here, to overcome these issues, this work reports plasma assisted NH 3 /H 2 oxidation and unveils the kinetics of fuel oxidation and N 2 O/NO x formation by combining time-resolved laser diagnostics with plasma modeling. Firstly, we found that the NH 3 consumption is promoted with a H 2 blending ratio of 0.3, due to enhancements of H and OH formation by plasma assisted H 2 dissociation. Secondly, at a high reduced electric field, when the H 2 blending ratio increases, the NH 3 oxidation is promoted due to both the HO 2 formation and strong NO kinetic enhancement via NO-HO 2 and NO 2 -H pathways. In the meantime, it is shown that the NO mole fraction also increases with H 2 blending ratio, because the NO formation is enhanced via N( 2 D)-O 2 pathways, and the DeNO x chemistry is weakened with less NH 2 production. By contrast, at a lower reduced electric field, when the H 2 blending ratio increases, the decreased N( 2 D) formation does not produce enough NO to replenish the NO formation drop caused by lower NH 3 concentration. Thirdly, the reduced electric field non-monotonically affects fuel consumption and N 2 O/NO x formation by manipulating electron energy deposition pathways. The NH 3 consumption is maximized with an optimal reduced electric field where N 2 * excitation and O 2 dissociation are most efficient. When the reduced electric field deviates from its optimum, the NH 3 consumption decreases due to the discharge energy deposition to either vibrational excitation or dissociation of N 2 . The N 2 O/NO x emissions governed by the NH 3 oxidation follow the above NH 3 consumption trend.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ultrasonic-Assisted Extrusion Processing for Enhancing Physical Properties of High-Density Polyethylene by Flow-Induced Crystallization

The evolution of crystallinity resulting from stress imposed on a melt, known as flow-induced crystallinity, can strongly influence the mechanical and physical properties of semicrystalline polymers. This study investigates shear-induced crystallization by applying an ultrasonic field to the melt flow as it passes through dies with various geometries. A custom-built sonication die is employed for controlling the dynamic temperature and shear environment, resulting in molecular alignment and potential for flow-induced crystallization. Application of both conventional and ultrasonic shear rates at the equilibrium melt temperature of high-density polyethylene (HDPE) was investigated to accelerate crystallinity and manipulate the crystal morphology across the film in pursuit of improved mechanical and gas barrier properties without the need for additives or other polymer layers. The relationships among ultrasonic-assisted extrusion processing, polymer structure, and performance were analyzed using wide- and small-angle X-ray scattering (WAXS and SAXS), tensile testing, and oxygen transmission rate (OTR) analysis. Multiple linear regression models were implemented to predict the correlation among HDPE structure, process, and properties. Structural analysis revealed that both conventional and ultrasonic shear rates had the most significant influence on lamellar spacing and redistribution of rigid and soft amorphous fractions within the crystalline domains, ultimately dictating the mechanical and physical properties of the films. The goal is to explore the potential of the ultrasonic-assisted high crystallinity monolayer that can replace some of the functionality of complex, heterogeneous multilayer packaging with a single-material film having enhanced oxygen barrier properties.

crystallinity↗

Pulsed Laser-Assisted Focused Electron-Beam-Induced Etching of Titanium with XeF 2 : Enhanced Reaction Rate and Precursor Transport

We introduce a laser-assisted focused electron-beam-induced etching (LA-FEBIE) process which is a versatile, direct write nanofabrication method that allows nanoscale patterning and editing; we do this in order to enhance the etch rate of electron-beam-induced etching. The results demonstrate that the titanium electron stimulated etch rate via the XeF2 precursor can be enhanced up to a factor of 6 times with an intermittent pulsed laser assist. Moreover, the evolution of the etching process is correlated to in situ stage current measurements and scanning electron micrographs as a function of time. Finally, the increased etch rate is attributed to photothermally enhanced Ti–F reaction and TiF4 desorption and in some regimes enhanced XeF2 surface diffusion to the reaction zone.

36 MATERIALS SCIENCE↗

IEA Wind Task 32: Best Practices for the Certification of Lidar-Assisted Control Applications

Lidar-assisted control is a promising technology for reducing structural loads on wind turbines. Guidelines for certifying wind turbines with this technology are important for its widespread adoption. As a first step, an IEA Wind Task 32 workshop was held, bringing together wind turbine manufacturers, lidar suppliers, certifiers, consultants, and researchers to identify barriers to certification with lidar-assisted control and ideas for mitigating the barriers. Here this paper builds on the outcome of the workshop by providing an analysis of the areas affected and the remaining challenges. Further, initial best practices are given to address the challenges, covering the lidar system, control and protection systems, design loads, and type testing.

17 WIND ENERGY↗

Solar Technical Assistance Team (STAT) (Fact Sheet)

The Solar Technical Assistance Team (STAT) is a team of solar technology and deployment experts who ensure that the best information on policies, regulations, financing and other issues is getting into the hands of state government decision makers at the time they need it. The goal of the team is to provide timely, unbiased expertise to assist key policy makers and regulators in making informeddecisions.

14 SOLAR ENERGY↗

Analysis and Methane Gas Separations Studies for City of Marsing, Idaho. An Idaho National Laboratory Technical Assistance Program Study

Introduction and Background: Large amounts of methane in well water is a wide spread problem in North America. Methane gas from decaying biomass and oil and gas deposits escape into water wells typically through cracks or faults in otherwise non-porous rock strata producing saturated water systems. This methane saturated water can pose several problems in the delivery of drinking water. The problems range from pumps vapor locking (cavitating), to pump houses exploding. The City of Marsing requested Idaho National Laboratory (INL) to assist with some water analyses as well as to provide some engineering approaches to methane capture through the INL Technical Assistance Program (TAP). There are several engineering approaches to the removal of methane and natural gas from water sources that include gas stripping followed by compression and/or dehydration; membrane gas separators coupled with dehydration processes, membrane water contactors with dehydration processes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Renewable Energy Project Development Assistance (Fact Sheet)

This fact sheet provides information on the Tribes selected to receive assistance from the U.S. Department of Energy Office of Indian Energy 2013 Strategic Technical Assistance Response Team (START) Program, which provides technical expertise to support the development of next-generation energy projects on tribal lands.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Techniques for energetic ion assisted in-situ coating of long, small diameter, beam pipes with compacted thick crystalline copper film

High wall resistivity can cause heating and instabilities in accelerators. Electron clouds in accelerators limit machine performance through associated dynamical instabilities and/or vacuum pressure increases. Coating accelerator vacuum tubes with compacted thick crystalline copper will mitigate those problems and can enhance luminosity. Develop compact ion assisted deposition (IAD) devices by incorporating ion bombardment in a robotic cylindrical magnetron sputtering device configured for small radial dimension tubes for in-situ coating of long, small diameter tubes with defect free thick films copper. Selected an ion assisted plasma deposition technique for in-situ coating of long, small diameter tubes. Set up a cryogenic resonator for measuring conductivity of deposited copper at cryogenic temperature to optimize the deposition technique; preliminary design of phase II full-scale device. Coating of existing accelerator vacuum tubes with compacted thick crystalline copper is a very cost effective way to mitigate significant problems in accelerators trying to increase luminosity. IAD results in superior quality film deposition, which due to inefficiencies, is presently restricted to high value items. Advancing to industry forefront more cost effective IAD, will improve tools, ball bearings & other lower value industrial products, thus reducing waste as well as improving industrial accelerators and electron guns, impacting companies who utilize accelerators. Develop improved inexpensive plasma deposition for copper coating accelerator tubes with compacted thick crystalline copper. Although there are commercial applications, initial project focus is to facilitate cost-effective luminosity increase in RHIC at BNL as well as other machines.

43 PARTICLE ACCELERATORS↗

Effect of Swelling on Irradiation-Assisted Stress Corrosion Cracking

A highly irradiated stainless steel 304 material irradiated to 27 dpa in the Experimental Breeder Reactor-II was used to investigate the relation between void swelling, grain boundary cohesion and intergranular crack growth rate under solicitation by irradiation assisted stress corrosion cracking. The material selected offered two different swelling amounts (about 2% and 3.7%) in the same material at high dose. The material had been irradiated at the same time, same condition, only the temperature gradient led to different swelling. This material, however, proved to be very resistant to irradiation assisted stress corrosion cracking under pressurized water reactor conditions. The crack growth rates measured were very low with the lowest being obtained with the material exhibiting the most amount of swelling. Micromechanical testing performed with the material exhibiting the higher crack propagation rate demonstrated that the irradiation damages (including void swelling) did not decrease grain boundary cohesion enough to make the grain boundaries the weak points under load solely. Crack path and crack tip analysis showed evidence of material modification ahead of the crack but it is not clear, at this point, if the changes observed were caused by the crack advance or if their presence in front of the crack was causing the low crack growth rate measured.

36 MATERIALS SCIENCE↗

Creating an Inter-Tribal Technical Assistance Network in the Northwest Arctic

The US Department of Energy-Office of Indian Energy's (DOE-IE) support for NANA's establishment of an Inter-Tribal Assistance Network in the Northwest Arctic was a ground-breaking effort that led to many individual community successes and a regional escalation of clean energy for our tribes. Before this grant award was initiated, high penetration renewable-diesel hybrid systems were primarily aspirational. Now, after five years of intensive technical assistance and multi-institution collaboration and funding, the NANA Region has three high penetration solar-wind-battery-diesel hybrid systems and one solar-battery-diesel hybrid system fully operational with diesel-off operation occurring regularly; another solar-battery-diesel hybrid system fully funded with an RFP for construction targeted for 2023; a current grant application that was awarded to begin the final design process for solar-battery-diesel hybrid systems for four other villages in the region; and initial funding to begin a high penetration wind-battery-diesel system for the remaining village in the region. Clearly, our goal to demonstrate and replicate high penetration renewable hybrid technology has been accomplished and is increasing in scale and pace.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Can a Nuclear-Assisted Biofuels System Enable Liquid Biofuels as the Economic Low-carbon Replacement for All Liquid Fossil Fuels and Hydrocarbon Feedstocks and Enable Negative Carbon Emissions?

This report integrates the results of a series of studies and workshops to address the question: Can a nuclear-assisted biofuels system enable liquid biofuels as the economic low-carbon replacement for all liquid fossil fuels and hydrocarbon feedstocks and simultaneously enable negative carbon emissions? “Economic” is defined as economically competitive relative to other low-carbon replacement options for crude oil. “All” refers to the capability to replace the 18 million barrels of oil per day used by the United States. “Nuclear-assisted” refers to the provision of massive quantities of low-carbon heat and hydrogen at the refinery to fully utilize the carbon content of the cellulosic biomass feedstocks for liquid hydrocarbon production. A system is proposed that decarbonizes about half of the U.S. economy while improving long-term soil productivity and sequestering carbon from the atmosphere. In the U.S. almost half the energy consumed by the final customer is in the form of liquid hydrocarbons produced from crude oil. Liquid hydrocarbons are used as (1) an energy source, (2) a method for daily-to-seasonal energy storage, (3) a chemical feedstock, (4) a chemical reducing agent, (5) a method to enhance high-temperature heat transfer in many furnaces and industrial processes and (6) other purposes. As a consequence, the U.S. consumes ~18 million barrels of crude oil per day to produce liquid hydrocarbons. While there are substitutes for liquid hydrocarbons for some applications, our assessment is that the costs and difficulty will dramatically increase if liquid hydrocarbon use goes much below the equivalent of 10 million barrels per day of crude oil. New uses of liquid hydrocarbons to partly replace coal and natural gas could increase demand beyond the equivalent of 10 million barrels of oil per day. One can produce and burn liquid hydrocarbons from biomass without any net addition of carbon dioxide to the atmosphere. Plants grow by removing carbon dioxide from the atmosphere; thus, burning biomass does not result in any net addition of carbon dioxide to the atmosphere. Biomass is typically 40% oxygen. To remove this oxygen to create hydrocarbon liquids, there are two options. The first option is to use biomass as (1) a feedstock, (2) an energy source to operate the process and (3) a supply of carbon to remove the biomass oxygen as carbon dioxide. The second option is to use external heat and hydrogen to remove the oxygen as water and produce liquid hydrocarbons. The use of massive quantities of external heat and hydrogen for hydrocarbon liquid fuels production reduces the biomass feedstock per unit of liquid hydrocarbon product by more than a factor of two reducing land use by more than a factor of two. Many cellulosic feedstocks unsuitable for liquid hydrocarbon production are viable feedstocks with external heat and hydrogen inputs. As a result, there is sufficient cellulosic feedstocks to meet U.S. and global liquid fuels hydrocarbon demand without significant impacts on food and fiber prices. The heat and hydrogen (heat plus electricity) are produced using base-load nuclear power plants—the most economic form of nuclear energy. If low-price natural gas, there is also the option of producing hydrogen from natural gas with sequestration of the carbon dioxide. The biomass is locally processed in depots to produce commodity feedstocks that can be shipped long distances to large biorefineries (250,000 barrels per day, oil equivalent) similar to existing refineries except modifications of front-end processes. The depot system enables local recycle of nutrients back to the soil. The biorefinery can produce variable quantities of liquid hydrocarbon fuels and carbon dioxide for sequestration enabling removal of carbon dioxide from the atmosphere. Preliminary estimates are that the liquid hydrocarbon costs are equivalent to crude oil at between $60 and $70 per barrel. The largest cost is for hydrogen with biomass feedstocks and refinery costs a smaller fraction of the total cost.

09 BIOMASS FUELS↗

Advanced Energy Manufacturing and Recycling Grant Readiness Technical Assistance Program [Slides]

The U.S. Department of Energy's Office of Manufacturing and Energy Supply Chains (MESC) has launched a new technical assistance program, administered by NREL, in support of prospective applicants to the Advanced Energy Manufacturing and Recycling Grant Program. The competitive technical assistance program will help small- and medium-sized manufacturers understand the requirements of the Advanced Energy Manufacturing and Recycling Grant Program and prepare for future applications. Such applications must propose a project to build, retrofit, or expand facilities in coal communities for producing or recycling goods used to support clean energy supply chains. This presentation is for an informational webinar on Wednesday, April 26, 2023.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

International Clean Energy Analysis Gateway: Assisting Developing Countries with Clean Energy Deployment (Fact Sheet)

The International Clean Energy Analysis Gateway seeks to enhance developing country access to energy efficiency and renewable energy analysis tools, databases, methods, and other technical resources in a dynamic user interaction environment. In addition to providing information on available tools, the gateway also is a platform for Web seminars, online training, peer networks, and expert assistance. The gateway is sponsored by the U.S. Department of Energy (DOE) and the United Nations Industrial Development Organization (UNIDO) and managed by the National Renewable Energy Laboratory (NREL). Further cooperation is desired with organizations that can help expand the information presented in the portal and assist with outreach and training.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Microwave-Assisted Preparation of Luminescent Inorganic Materials: A Fast Route to Light Conversion and Storage Phosphors

Luminescent inorganic materials are used in several technological applications such as light-emitting displays, white LEDs for illumination, bioimaging, and photodynamic therapy. Usually, inorganic phosphors (e.g., complex oxides, silicates) need high temperatures and, in some cases, specific atmospheres to be formed or to obtain a homogeneous composition. Low ionic diffusion and high melting points of the precursors lead to long processing times in these solid-state syntheses with a cost in energy consumption when conventional heating methods are applied. Microwave-assisted synthesis relies on selective, volumetric heating attributed to the electromagnetic radiation interaction with the matter. The microwave heating allows for rapid heating rates and small temperature gradients yielding homogeneous, well-formed materials swiftly. Luminescent inorganic materials can benefit significantly from the microwave-assisted synthesis for high homogeneity, diverse morphology, and rapid screening of different compositions. The rapid screening allows for fast material investigation, whereas the benefits of enhanced homogeneity include improvement in the optical properties such as quantum yields and storage capacity.

59 BASIC BIOLOGICAL SCIENCES↗

CFD-Guided Evaluation of Spark-Assisted Gasoline Compression Ignition for Cold Idle Operation

A closed-cycle, three-dimensional (3D) computational fluid dynamics (CFD) analysis campaign was conducted to evaluate the performance of using spark plugs to assist gasoline compression ignition (GCI) combustion during cold idle operations. A conventional spark plug using single-sided J-strap design was put at a location on the cylinder head to facilitate spray-guided spark assistance. Ignition was modeled with an L-type energy distribution to depict the breakdown and the arc-to-glow phases during the energy discharge process. Several key design parameters were investigated, including injector clocking, number of nozzle holes, spray inclusion angle, number of fuel injections, fuel split ratio, and fuel injection timings. The study emphasized the region around the spark gap, focusing on flame kernel formation and development and local equivalence ratio distribution. Flame kernel development and the ignition process were found to correlate strongly with the fuel stratification and the flow velocity near the spark gap. The analysis results showed that the flame kernel development followed the direction of the local flow field. In addition, the local fuel stratification notably influenced early-stage flame kernel development due to varying injection spray patterns and the fuel injection strategies. Among these design parameters, the number of nozzle holes and fuel injection timing had the most significant effects on the engine combustion performance.

42 ENGINEERING↗

Atmospheric Sounder Spectrometer for Infrared Spectral Technology (ASSIST): summary data

This datastream encapsulates the contents of the ASSIST "ExtraCSV" files. The ExtraCSV files contain an array of defined system constants, quantities derived from the calibrated radiances including brightness temperatures and noise estimates. It also contains most values from both the housekeeping (hkp) and annotator (ann) files except at coarser temporal resolution so represents a virtual one-stop-shop for determining the ASSIST system status.

54 ENVIRONMENTAL SCIENCES↗

Technical Assistance

DOE-TTO Annual Merit Review presentation on the Technical Assistance task, covering FY25-26. Includes an overview of what technical assistance is and highlights three key projects: (1) FLeet CNG Infrastructure Clean Cities TA request, (2) 3D Mobile App for Emergency Responders (for EVs) Pilot Project, and (3) Smart Playbook for Fleets AFDC content development.

33 ADVANCED PROPULSION SYSTEMS↗