Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Sensitivity analysis results of the effects of various parameters on composite design

Sensitivity analysis results are presented to assess the effects of a multitude of important parameters on fiber composite design and structural response. These results were obtained by using optimum design procedures in conjunction with sensitivity analyses. Sensitivity analyses were performed to assess the effects on composite optimum design and structural response of parameters such fiber transverse and shear properties, in situ matrix elastic and strength properties, correlation coefficients used in composite micromechanics and in combined strength predictions, processing variables, and perturbations of loading conditions. The results show that matrix properties, fiber volume ratio and small perturbations of the loading conditions have significant effects on certain composite structural responses. The remaining parameters have negligible effect.

Chamis, C. C.↗
NASA NTRS1987

Controller for a High-Power, Brushless dc Motor

Driving and braking torques controllable. Control circuit operates 7-kW, 45-lb-ft (61-N-m), three-phase, brushless dc motor in both motor and generator modes. In motor modes, energy from power source is pulse-width modulated to motor through modified "H-bridge" circuit, in generator mode, energy from motor is pulse-width modulated into bank of load resistors to provide variable braking torques. Circuit provides high-resolution torque control in both directions over wide range of speeds and torques. Tested successfully at bus voltages up to 200 Vdc and currents up to 45 A.

Fleming, David J.↗
NASA NTRS1989

Transonic airfoil design for helicopter rotor applications

Despite the fact that the flow over a rotor blade is strongly influenced by locally three-dimensional and unsteady effects, practical experience has always demonstrated that substantial improvements in the aerodynamic performance can be gained by improving the steady two-dimensional charateristics of the airfoil(s) employed. The two phenomena known to have great impact on the overall rotor performance are: (1) retreating blade stall with the associated large pressure drag, and (2) compressibility effects on the advancing blade leading to shock formation and the associated wave drag and boundary-layer separation losses. It was concluded that: optimization routines are a powerful tool for finding solutions to multiple design point problems; the optimization process must be guided by the judicious choice of geometric and aerodynamic constraints; optimization routines should be appropriately coupled to viscous, not inviscid, transonic flow solvers; hybrid design procedures in conjunction with optimization routines represent the most efficient approach for rotor airfroil design; unsteady effects resulting in the delay of lift and moment stall should be modeled using simple empirical relations; and inflight optimization of aerodynamic loads (e.g., use of variable rate blowing, flaps, etc.) can satisfy any number of requirements at design and off-design conditions.

Hassan, Ahmed A.↗
NASA NTRS1992

Stress and tectonics on Mars

Deformation of the Martian lithosphere and the various theoretical formulations used to model its behavior on local, regional, and global scales are studied. An overview of the various classes of tectonic features found on Mars is presented. The tectonic record on Mars, which provides the basic framework for interpreting theoretical thermomechanical models in terms of major tectonic events and provinces is summarized. The thickness of the elastic lithosphere is estimated using its response to local surface loads, and significant spatial variability is found, with values ranging from 20 to 300 km. A comparison of the major radial graben systems with theoretical stress models shows that more than one mechanism of lithospheric deformation is required to produce its enormous extent.

Banerdt, W. B.↗
NASA NTRS1939

A recurrence formula for shear-lag problems

The analysis of the bending action in box beams with appreciable shear deformation of the flanges becomes very difficult in the general case of variable cross section and loading. This paper presents a convenient method of solving the problem by the familiar method of dividing the beam into a number of bays that can be assumed to have constant cross section and loading. Application of formerly derived shear-lag formulas leads to a general equation closely analogous in form to the well-known three-moment equation. A numerical example and two comparisons between calculation and experimental results are included.

Kuhn, Paul↗
NASA NTRS1994

Experimental evaluation of shape memory alloy actuation technique in adaptive antenna design concepts

Creation of an antenna system that could autonomously adapt contours of reflecting surfaces to compensate for structural loads induced by a variable environment would maximize performance of space-based communication systems. Design of such a system requires the comprehensive development and integration of advanced actuator, sensor, and control technologies. As an initial step in this process, a test has been performed to assess the use of a shape memory alloy as a potential actuation technique. For this test, an existing, offset, cassegrain antenna system was retrofit with a subreflector equipped with shape memory alloy actuators for surface contour control. The impacts that the actuators had on both the subreflector contour and the antenna system patterns were measured. The results of this study indicate the potential for using shape memory alloy actuation techniques to adaptively control antenna performance; both variations in gain and beam steering capabilities were demonstrated. Future development effort is required to evolve this potential into a useful technology for satellite applications.

Kefauver, W. Neill↗
NASA NTRS1996

Test and Analysis of Composite Hat Stringer Pull-off Test Specimens

Hat stringer pull-off tests were performed to evaluate the delamination failure mechanisms in the flange region for a rod-reinforced hat stringer section. A special test fixture was used to pull the hat off the stringer while reacting the pull-off load through roller supports at both stringer flanges. Microscopic examinations of the failed specimens revealed that failure occurred at the ply termination in the flange area where the flange of the stiffener is built up by adding 45/-45 tape plies on the top surface. Test results indicated that the as-manufactured microstructure in the flange region has a strong influence on the delamination initiation and the associated pull-off loads. Finite element models were created for each specimen with a detailed mesh based on micrographs of the critical location. A fracture mechanics approach and a mixed mode delamination criterion were used to predict the onset of delamination and the pull-off load. By modeling the critical local details of each specimen from micrographs, the model was able to accurately predict the hat stringer pull-off loads and replicate the variability in the test results.

Li, Jian↗
NASA NTRS1998

Towards a Probabilistic Criterion for Preliminary Shell Design

Thin-walled stiffened or unstiffened, metallic or composite shells are widely used structural elements in aeronautical and space applications. Buckling strength, which is a major concern in all these areas, is affected by the uncertainties in the definition of loads, material properties, geometric variables, engineering models and the accuracy of the analysis tools used in the design phase. The NASA design criteria monographs from the late sixties account for these design uncertainties by the use of a lump sum safety factor or the so-called "knockdown" factor gamma, which usually results in an overly conservative design. In the present paper a new, reliability based, probabilistic design procedure for buckling critical imperfect isotropic shells is proposed. It essentially consists of a stochastic approach based on a new, improved "knockdown" factor lambda(sub a) that is not as conservative as the traditional one. It is felt that by quantifying and understanding the "problem uncertainties" such as initial imperfections and their influence on the design variables, one can develop a better engineered, better designed and safer system.

Arbocz, Johann↗
NASA NTRS2001

On the Accuracy of Probabilistic Bucking Load Prediction

The buckling strength of thin-walled stiffened or unstiffened, metallic or composite shells is of major concern in aeronautical and space applications. The difficulty to predict the behavior of axially compressed thin-walled cylindrical shells continues to worry design engineers as we enter the third millennium. Thanks to extensive research programs in the late sixties and early seventies and the contributions of many eminent scientists, it is known that buckling strength calculations are affected by the uncertainties in the definition of the parameters of the problem such as definition of loads, material properties, geometric variables, edge support conditions, and the accuracy of the engineering models and analysis tools used in the design phase. The NASA design criteria monographs from the late sixties account for these design uncertainties by the use of a lump sum safety factor. This so-called 'empirical knockdown factor gamma' usually results in overly conservative design. Recently new reliability based probabilistic design procedure for buckling critical imperfect shells have been proposed. It essentially consists of a stochastic approach which introduces an improved 'scientific knockdown factor lambda(sub a)', that is not as conservative as the traditional empirical one. In order to incorporate probabilistic methods into a High Fidelity Analysis Approach one must be able to assess the accuracy of the various steps that must be executed to complete a reliability calculation. In the present paper the effect of size of the experimental input sample on the predicted value of the scientific knockdown factor lambda(sub a) calculated by the First-Order, Second-Moment Method is investigated.

Arbocz, Johann↗
NASA NTRS1995

Wear Measurement System

Lewis Research Center developed a tribometer for in-house wear tests. Implant Sciences Corporation (ISC), working on a NASA contract to develop coatings to enhance the wear capabilities of materials, adapted the tribometer for its own use and developed a commercial line of user-friendly systems. The ISC-200 is a pin-on-disk type of tribometer, functioning like a record player and creating a wear groove on the disk, with variables of speed and load. The system can measure the coefficient of friction, the wear behavior between materials, and the integrity of thin films or coatings. Applications include measuring wear on contact lenses and engine parts and testing disk drives.

Source record↗
NASA NTRS2011

The Effects of Foam Thermal Protection System on the Damage Tolerance Characteristics of Composite Sandwich Structures for Launch Vehicles

For any structure composed of laminated composite materials, impact damage is one of the greatest risks and therefore most widely tested responses. Typically, impact damage testing and analysis assumes that a solid object comes into contact with the bare surface of the laminate (the outer ply). However, most launch vehicle structures will have a thermal protection system (TPS) covering the structure for the majority of its life. Thus, the impact response of the material with the TPS covering is the impact scenario of interest. In this study, laminates representative of the composite interstage structure for the Ares I launch vehicle were impact tested with and without the planned TPS covering, which consists of polyurethane foam. Response variables examined include maximum load of impact, damage size as detected by nondestructive evaluation techniques, and damage morphology and compression after impact strength. Results show that there is little difference between TPS covered and bare specimens, except the residual strength data is higher for TPS covered specimens.

Nettles, A. T.↗
NASA NTRS2011

Major Influence of Tropical Volcanic Eruptions on the Stratospheric Aerosol Layer During the Last Decade

The variability of stratospheric aerosol loading between 1985 and 2010 is explored with measurements from SAGE II, CALIPSO, GOMOS/ENVISAT, and OSIRIS/Odin space-based instruments. We find that, following the 1991 eruption of Mount Pinatubo, stratospheric aerosol levels increased by as much as two orders of magnitude and only reached background levels between 1998 and 2002. From 2002 onwards, a systematic increase has been reported by a number of investigators. Recently, the trend, based on ground-based lidar measurements, has been tentatively attributed to an increase of SO2 entering the stratosphere associated with coal burning in Southeast Asia. However, we demonstrate with these satellite measurements that the observed trend is mainly driven by a series of moderate but increasingly intense volcanic eruptions primarily at tropical latitudes. These events injected sulfur directly to altitudes between 18 and 20 km. The resulting aerosol particles are slowly lofted into the middle stratosphere by the Brewer-Dobson circulation and are eventually transported to higher latitudes.

Vernier, Jean-Paul↗
NASA NTRSDate not supplied

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Plasma↗
NASA NTRSDate not supplied

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Space Crop Production↗
DOE OSTI2024

Dynamic Modeling and Simulation of a Subcritical Coal-Fired Power Plant under Load-Following Conditions

Dynamic models for power plants that capture realistic general process trends and effects of manipulated variables are needed to improve load-following, while minimizing carbon footprint. In this work, a dynamic modeling approach and simulation results for subcritical coal-fired power plant components are presented. These encompass simulation of the dynamics in the fireside, including the effects of fuel, air combustion, and the dynamics of the entire waterside and power generation sections. This model development enables the simulation and analysis of the important short and long-time scale dynamics of components such as heaters, evaporative loop, and power generation units. Furthermore, additional variables in the power generation section are introduced to improve model accuracy, extending the prediction capability of subcritical power plant models and opening new opportunities for research in operator training, optimization, and advanced model-based controller design that are based on these models. The change in process gain for different ramp rates associated with disturbance signals that affect process variables is also explored and a correlation developed. This provides opportunities to study disturbance rejection control implementation and adaptation for scenarios with such variations in ramp rates. The prediction capabilities of selected components are compared to data available in literature, with the obtained root mean squared error ranges that reflect the model performance and quality of predictions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

Composite load spectra for select space propulsion structural components

The objective of this program is to develop generic load models to simulate the composite load spectra (CLS) that are induced in space propulsion system components representative of the space shuttle main engines (SSME). These models are being developed through describing individual component loads with an appropriate mix of deterministic and state-of-the-art probabilistic models that are related to key generic variables. Combinations of the individual loads are used to synthesize the composite loads spectra. A second approach for developing the composite loads spectra load model simulation, the option portion of the contract will develop coupled models which combine the individual load models. Statistically varying coefficients of the physical models will be used to obtain the composite load spectra.

Newell, J. F.↗
NASA NTRS1985

Probabilistic Finite Element Development

The probabilistic finite element computer program known as Numerical Evaluation of Stochastic Structures Under Stress (NESSUS) is being developed for the analysis of critical structural components for reusable space propulsion systems. First year efforts involve the formulation of the probabilistic analysis strategy and the development of a probabilistic linear analysis code. The ultimate goal of the 3-year program is the development of a finite element code capable of performing nonlinear dynamic analysis of structures having stochastic material properties, geometry, and boundary conditions and subjected to random loading. Three levels of sophistication are envisioned for the stochastic description of the structural problem, namely: (1) homogeneous random variable for stiffness, mass, damping, and external loading; (2) stochastic characterization of variables at the element level, with specified interelement correlations; and (3) stochastic interpolation of variables within a finite element. Two alternative probabilistic analysis methods will be developed, allowing for all three levels of modeling sophistication.

Nagtegaal, J.↗
NASA NTRS2011

Iterative Strain-Gage Balance Calibration Data Analysis for Extended Independent Variable Sets

A new method was developed that makes it possible to use an extended set of independent calibration variables for an iterative analysis of wind tunnel strain gage balance calibration data. The new method permits the application of the iterative analysis method whenever the total number of balance loads and other independent calibration variables is greater than the total number of measured strain gage outputs. Iteration equations used by the iterative analysis method have the limitation that the number of independent and dependent variables must match. The new method circumvents this limitation. It simply adds a missing dependent variable to the original data set by using an additional independent variable also as an additional dependent variable. Then, the desired solution of the regression analysis problem can be obtained that fits each gage output as a function of both the original and additional independent calibration variables. The final regression coefficients can be converted to data reduction matrix coefficients because the missing dependent variables were added to the data set without changing the regression analysis result for each gage output. Therefore, the new method still supports the application of the two load iteration equation choices that the iterative method traditionally uses for the prediction of balance loads during a wind tunnel test. An example is discussed in the paper that illustrates the application of the new method to a realistic simulation of temperature dependent calibration data set of a six component balance.

Ulbrich, Norbert Manfred↗