SEARCH · Engineering Papers

Results for “thin membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Membrane-Based Air Dehumidification Using Organic Ionic Liquid Desiccant

Membrane Ionic Liquid Desiccant Air Dehumidification (MILDAD) is a promising alternative to conventional dehumidification systems that employ mechanical compressors and refrigerant-based cooling with evaporator and condensing coils. However, its application has been limited due to high manufacturing and installation cost, durability issues, concerns with corrosion due to leakage and salt carry over into the downstream air and onto surfaces. This paper reviews substantial progress made with new systems based on combining advanced ionic membranes that are pressure resistant, thin walled with high water permeability, and non-porous with synthetic organic, non-crystalline ionic liquid desiccants. Alternative design configurations are discussed comparing cross flow shell-and-tube membrane contactors employing ionic membrane tubes through which ionic liquid desiccant air flows. Performance data for MILDAD prototypes is provided. Dehumidification of the incoming supply airstream and regeneration into exhausted building air is demonstrated. The latent effectiveness of the MILDAD system will be discussed along with some future steps to improve performance of the system.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗

NASA NTRS1980

Experimental investigation of drag on a compliant surface

The feasibility of reducing turbulent skin-friction drag by means of surface compliance was studied experimentally in a fully developed flat-plate turbulent boundary layer in air, using a membranous surface backed by a thin cavity containing a layer of polyurethane foam. Surface motion characteristics, boundary layer structure, and overall drag were measured over a range of freestream speeds from 7 to 30 m/sec, and a range of membrane tensions from 44 to 350 N/m. Low-amplitude long-wavelength motions predominate, and no significant change from the rigid surface skin-friction coefficients was observed.

Mcmichael, J. M.↗

DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Abstract All‐solid‐state Li‐metal battery (ASSLB) chemistry with thin solid‐state electrolyte (SSE) membranes features high energy density and intrinsic safety but suffers from severe dendrite formation and poor interface contact during cycling, which hampers the practical application of rechargeable ASSLB. Here, we propose a universal design of thin Li‐metal anode (LMA) via a dynamic stability strategy to address these issues. The ultra‐thin LMA (20 μm) is in situ constructed with uniform highly Li‐ion conductive solid‐electrolyte interphase and composite‐polymer interphase (CPI) via electroplating process. As a result, the passivation layer with poor Li‐ion conduction on Li anode can be dissolved and small surface resistance can be achieved due to the good compatibility of CPI to SSEs. The cycling of Li symmetric cell with Li 6 PS 5 Cl thin film electrolyte (<100 μm) shows a high critical current density of >2.0 mA cm −2 with excellent cycling stability at 1.0 mA cm −2 . The ASSLBs paring with Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode demonstrated the feasibility of engineered LMA design by presenting good rate capability from 0.1 C to 1.0 C at room temperature, as well as long‐term cycling stability (81 % retention after 100 cycles). This work represents a general pathway to make thin dendrite‐free LMA available for high‐energy‐density ASSLBs.

Deng, Tao [Department of Chemical and Biomolecular↗

DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Deng, Tao [Department of Chemical and Biomolecular↗

DOE OSTI2025

Durability Optimization of CO 2 Electrolyzers for Syngas Evolution

Recently, there has been an increased interest in mitigating anthropogenic CO 2 emissions through the electrochemical conversion of CO 2 into fuels and fuel feedstocks, including hydrogen gas (H 2 ), carbon monoxide (CO), and mixtures of the two to yield syngas. Commercial applications of these systems require high catalytic selectivity for the desired products, while exhibiting operational lifetimes exceeding thousands of hours. Advancements in this field have produced systems that display high selectivity of the desired products at faradaic efficiencies exceeding 95%. Despite the advancements made in CO 2 electrolysis, system durability remains a standing challenge in the field. CO 2 electrolyzer lifetimes are often limited by carbonate fouling, catalyst degradation, detrimental flooding of electrode microporous layers and anion exchange membrane (AEM) failures. In this report, a 5 cm 2 membrane electrode assembly (MEA) device is used to investigate potential failure modes and to optimize AEM CO 2 electrolyzer operation. Key findings of this study include the importance of CO 2 flow rate, use of a thin PiperION PTFE-reinforced membrane, optimizing compression to enhance contact under 40 in-lb compression, and the effect of more compressible, commercial iridium oxide anodes on system durability.

Abouremeleh, Mohammed H. [Lawrence Berkeley Nation↗

NASA NTRS1994

Molecular Dynamics of a Water-Lipid Bilayer Interface

We present results of molecular dynamics simulations of a glycerol 1-monooleate bilayer in water. The total length of analyzed trajectories is 5ns. The calculated width of the bilayer agrees well with the experimentally measured value. The interior of the membrane is in a highly disordered fluid state. Atomic density profile, orientational and conformational distribution functions, and order parameters indicate that disorder increases toward the center of the bilayer. Analysis of out-of-plane thermal fluctuations of the bilayer surfaces occurring at the time scale of the present calculations reveals that the distribution of modes agrees with predictions of the capillary wave model. Fluctuations of both bilayer surfaces are uncorrelated, yielding Gaussian distribution of instantaneous widths of the membrane. Fluctuations of the width produce transient thinning defects in the bilayer which occasionally span almost half of the membrane. The leading mechanism of these fluctuations is the orientational and conformational motion of head groups rather than vertical motion of the whole molecules. Water considerably penetrates the head group region of the bilayer but not its hydrocarbon core. The total net excess dipole moment of the interfacial water points toward the aqueous phase, but the water polarization profile is non-monotonic. Both water and head groups significantly contribute to the surface potential across the interface. The calculated sign of the surface potential is in agreement with that from experimental measurements, but the value is markedly overestimated. The structural and electrical properties of the water-bilayer system are discussed in relation to membrane functions, in particular transport of ions and nonelectrolytes across membranes.

Wilson, Michael A.↗

DOE OSTI2023

Electrically Driven Ion Separations in Permeable Membranes

Ion separations are critical for producing materials such as Li and rare-earth element salts that are essential for applications including energy storage and production. This research aimed to develop and understand separations of singly and multiply charged ions as well as separations among different singly charged ions such as Li + and Na + . Thin layers of polyelectrolytes on membranes allow passage of singly charged ions at rates 1000 times faster than those for multiply charged ions. This allows purification of mixtures with equal concentrations of Li + and Mg 2+ to create a permeate solution with >99% Li + . Such membranes may also effectively isolate rare earth elements. To separate Li + and K + , this work developed opposing flow and current in membranes. The current overcomes the flow of K + to allow Li + to selectively pass through the membrane, leading to Li + /K + selectivities around 70. All of the research employs modelling to better understand the mechanism of these separations, which includes transport driven by gradients in electrical potential, concentration, and pressure. The interplay of these driving forces can create highly selective separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2003

Ultra-Sensitive Magnetoresistive Displacement Sensing Device

An ultrasensitive displacement sensing device for use in accelerometers, pressure gauges, temperature transducers, and the like, comprises a sputter deposited, multilayer, magnetoresistive field sensor with a variable electrical resistance based on an imposed magnetic field. The device detects displacement by sensing changes in the local magnetic field about the magnetoresistive field sensor caused by the displacement of a hard magnetic film on a movable microstructure. The microstructure, which may be a cantilever, membrane, bridge, or other microelement, moves under the influence of an acceleration a known displacement predicted by the configuration and materials selected, and the resulting change in the electrical resistance of the MR sensor can be used to calculate the displacement. Using a micromachining approach, very thin silicon and silicon nitride membranes are fabricated in one preferred embodiment by means of anisotropic etching of silicon wafers. Other approaches include reactive ion etching of silicon on insulator (SOI), or Low Pressure Chemical Vapor Deposition of silicon nitride films over silicon substrates. The device is found to be improved with the use of giant magnetoresistive elements to detect changes in the local magnetic field.

Olivas, John D.↗

NASA NTRS2004

Fabrication of Monolithic Sapphire Membranes for High T(sub c) Bolometer Array Development

This paper examines the effectiveness of Pt/Cr thin film masks for the architecture of monolithic membrane structures in r-plane single crystal sapphire. The development of a pinhole-free Pt/Cr composite mask that is resistant to boiling H2SO4:H3PO4 etchant will lead to the fabrication of smooth sapphire membranes whose surfaces are well-suited for the growth of low-noise high Tc films. In particular, the relationship of thermal annealing conditions on the Pt/Cr composite mask system to: (1) changes in the surface morphology (2) elemental concentration of the Pt/Cr thin film layers and (3) etch pit formation on the sapphire surface will be presented.

Pugel, D. E.↗

DOE OSTI2024

Porous Organic Cage Membranes for Molecular Gas Separations (Final Technical Report for DE-SC0021357)

This proposal aims at demonstrating the development of a novel family of membranes, composed of porous organic cages (POC) which offer the possibility of displaying high separation performance for challenging molecular gas separations relevant to natural gas purification, and olefin/paraffin separation. The proposed POCs synthesized in membrane form will display the most desirable properties of polymers (facile processability and flexibility) and inorganic materials (hierarchically ordered pores with molecular sieving properties) leading to highly selective and permeable membranes. POCs should display distinctive structural, compositional, adsorption and transport properties than those of conventional porous materials, opening the doors for a new research direction in membrane science, and gas separations. Our preliminary results demonstrate the feasibility of preparing POC crystals with controlled size, and continuous POC membranes with remarkable high permeances, and separation ability for CO 2 /CH 4 , N 2 /CH 4 and C 3 H 6 /C 3 H 8 separations serving as a solid foundation for our proposed work. Fundamentally, this proposal aims at elucidating separation mechanisms of different gas mixtures related to natural gas composition, and olefin/paraffin separation over porous organic cage membranes. The proposed research will result in fundamental understanding of adsorption and transport properties of industrially relevant gas molecules through novel microporous membranes, and may lead to the development of a cost effective membrane technology for natural gas purification, and olefin/paraffin separation surpassing the conventional benchmark technology distillation. Furthermore, we aim at demonstrating selective water transport through POC membranes, which can be positively impactful in numerous industrial applications in which water is present. The ability to fabricate thin, chemically and mechanically stable POC membranes for societal relevant gas separations constitute a new and distinctive direction in membrane science. Our proposed work aims at addressing some of the challenges recognized in the Research Agenda for Transforming Separation Science . Specifically: (a) advancing understanding of complex mixtures on separation performance; (b) exploring thermodynamic and kinetic mechanisms through the elucidation of separation mechanisms, and (c) study potential stability issues of the membranes to be assessed by evaluating the long term membrane stability and performance at various temperatures and pressures. The team is uniquely qualified to execute the proposed work. The PI has solid expertise in the rational molecular engineering design of porous crystalline membranes for molecular gas separations. The PNNL collaborator has extensive experience in the synthesis, characterization, and functional applications of microporous crystals, with particular emphasis on gas adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Polyamide-Based Ion Exchange Membranes: Cation-Selective Transport through Water Purification Membranes

Ion-selective membranes are necessary components of many electrochemical systems including fuel cells, electrolyzers, redox flow batteries, and electrodialyzers. Perfluorinated sulfonated membranes (PFSMs) dominate these applications due to their excellent combination of fast ion transport, stability, and processability. However, perfluorinated cation exchange membranes (CEMs) are expensive, and their production process involves chemistry that generates toxic perfluorinated chemicals. The development of affordable, nonfluorinated membranes with a competitive combination of high ion selectivity, transport, and stability could help enable the widespread use of the technologies listed above while hastening the development of emerging electrochemical systems, including aqueous alkaline CO 2 sorbent regeneration. To this end, we pursue the use of thin-film composite polyamide (PA-TFCs) membranes–those that typically find application in reverse osmosis and nanofiltration desalination–as cation-selective exchange membranes. Given their negative surface charge under neutral-to-alkaline conditions, PA-TFCs can serve as effective CEMs in these pH regimes. We prepared a series of PA-TFCs from traditional monomers (trimesoyl chloride and piperazine) and compared their thicknesses, charge densities, water transport properties, ion transport properties, and long-term stability in a high pH environment to traditional CEMs (Nafion and FKE) and commercial nanofiltration and reverse osmosis membranes. We find that some of the best-performing PA-TFC membranes have similar resistances and Na + transference numbers compared to Nafion 117 in Na 2 SO 4 and NaHCO 3 -containing solutions. This proof-of-principle study suggests that further optimization of PA-TFCs could enable cost-effective ion exchange membrane alternatives to PFSMs.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Compositionally-Graded Shape Memory Film for Self-Deployment of Membrane Reflectors and Optics

The next generation of space systems will require large apertures in order to image faint targets or cover large areas of Earth. These large apertures must be able to fit inside a launch vehicle fairing, be light enough for launch into orbit, and deploy on orbit with repeatability and reliability. The current state-of-the-art in flight optics is represented by the 4 meter LAMP telescope, with an areal density of 10 km sq m. Development of a Beryllium mirror demonstration article for NGST (Next Generation Space Telescope) at the University of Arizona indicate areal densities of 0.5 kg sq m with flight hardware in the 12 meter range. With progressive improvements in existing deployment, packaging, and structural technologies, the size of optics and reflectors will continue to increase, while mass is reduced. However, without a breakthrough in materials, packaging and/or deployment technologies, the goal for Gossamer structures of 0.1 kg sq m is unachievable for the near and mid-term NASA missions. Membrane technology provides the best hope of achieving such low areal densities. In combination with advances in membrane materials and structures, development of revolutionary techniques for deployment systems can provide significant improvements in large aperture technology. In this paper, the results of a six-month Phase I research effort to demonstrate the application of thin film NiTi to aerospace-qualified membrane and mesh materials are presented. Deposition of shape memory thin film was achieved Astromesh (trademark) metal mesh and CP-1, and optical-quality polymer membrane. Not only was full-coating deposition demonstrated, but also small segment deposition which holds potential for local surface control. Deployment of these materials was also demonstrated, setting the stage for the development of a larger test article.

Hill, Lisa↗

DOE OSTI2023

Orientation matters: Measuring the correct surface of polyamide membranes with quartz crystal microbalance

The surface of polyamide reverse osmosis (RO) membranes which regulates interface-dominated phenomena, such as partitioning and fouling, is the one facing the feed during operation. However, the opposite surface of the polyamide selective layer, the one facing the permeate and in contact with the polysulfone porous support, is commonly analyzed in quartz crystal microbalance (QCM) measurements due to limitations of state-of-the-art transfer methodologies. Such measurements on the back surface cannot be generalized because the polyamide layer is chemically and morphologically asymmetric. Herein, we introduce a simple method to coat QCM sensors with polyamide active layers in the correct orientation (i.e., exposing their front surface) and show that interface-dominated phenomena differ significantly between orientations. We start by describing a transfer protocol to coat any surface with a polyamide layer on its front surface orientation. We then systematically analyze the chemical and morphological differences between the two surfaces of the polyamide layer of a commercial RO membrane. Finally, we demonstrate that interface-dominated phenomena depend on the orientation by showing that NaCl partitioning at pH 6 was 1.3 to 2.3-fold higher on the front surface and that organic fouling with humic acid occurred at a lower rate on this surface. The new method presented herein enables measurements on the front surface of polyamide RO membranes, which should be the standard in any future QCM studies.

Fouling behavior↗

NASA NTRS1992

Validation of the CQUAD4 element for vibration and shock analysis of thin laminated composite plate structure

The performance of the NASTRAN CQUAD4 membrane and plate element in the analysis of undamped natural vibration modes of thin fiber reinforced composite plates was evaluated. The element provides natural frequency estimates that are comparable in accuracy to alternative formulations, and, in most cases, deviate by less than 10 percent from experimentally measured frequencies. The predictions lie within roughly equal accuracy bounds for the two material types treated (GFRP and CFRP), and for the ply layups considered (unidirectional, cross-ply, and angle-ply). Effective elastic lamina moduli had to be adjusted for fiber volume fraction to attain this level of frequency. The lumped mass option provides more accurate frequencies than the consistent mass option. This evaluation concerned only plates with L/t ratios on the order of 100 to 150. Since the CQUAD4 utilizes first-order corrections for transverse laminate shear stiffness, the element should provide useful frequency estimates for plate-like structures with lower L/t. For plates with L/t below 20, consideration should be given to idealizing with 3-D solid elements. Based on the observation that natural frequencies and mode shapes are predicted with acceptable engineering accuracy, it is concluded that CQUAD4 should be a useful and accurate element for transient shock and steady state vibration analysis of naval ship

Lesar, Douglas E.↗

DOE OSTI2021

Studying Corrosion Using Miniaturized Particle Attached Working Electrodes and the Nafion Membrane

We developed a new approach to attach particles onto a conductive layer as a working electrode (WE) in a microfluidic electrochemical cell with three electrodes. Nafion, an efficient proton transfer molecule, is used to form a thin protection layer to secure particle electrodes. Spin coating is used to develop a thin and even layer of Nafion membrane. The effects of Nafion (5 wt% 20 wt%) and spinning rates were evaluated using multiple sets of replicates. The electrochemical performance of various devices was demonstrated. Additionally, the electrochemical performance of the devices is used to select and optimize fabrication conditions. The results show that a higher spinning rate and a lower Nafion concentration (5 wt%) induce a better performance, using cerium oxide (CeO2) particles as a testing model. The WE surfaces were characterized using atomic force microscopy (AFM), scanning electron microscopy-focused ion beam (SEM-FIB), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and X-ray photoelectron spectroscopy (XPS). The comparison between the pristine and corroded WE surfaces shows that Nafion is redistributed after potential is applied. Our results verify that Nafion membrane offers a reliable means to secure particles onto electrodes. Furthermore, the electrochemical performance is reliable and reproducible. Thus, this approach provides a new way to study more complex and challenging particles, such as uranium oxide, in the future.

42 ENGINEERING↗

DOE OSTI2026

Sculpting 2D Crystals via Membrane Contractions before and during Solidification

When phospholipids crystallize within the otherwise fluid membranes of giant unilamellar vesicles, the resulting molecularly thin “2D” solids exhibit great variety in their morphology evolution. For example, within membranes containing moderate amounts of the crystallizing component, crystals grow with a fixed morphology depending on vesicle size. Conversely for membranes containing large amounts of the crystallizing species, we find small compact crystals on vesicles of all sizes. However, on large vesicles, growing crystals sprout flower petals that lengthen progressively. These behaviors result from two combined mechanisms: first, like other 2D solids, the shear rigidity of phospholipid crystals renders them intolerant to morphologies with nonzero Gaussian curvature. As a result and especially at elevated membrane tension, the cost of bending elasticity is reduced at the expense of line energy by the formation of flowers as opposed to compact crystals. Second, the composition-dependent tension rise during cooling relaxes via water permeation of the membrane with a time constant scaling as R2. The amount of crystal formed for a small decrease in temperature determines this composition-dependent increase in stress from thermal contractions versus solidification. Surface Evolver computations were motivated using the predicted tension evolution to develop a processing space that maps to experimental observations for initial and growing crystal morphology. Important variable groups are identified, including a scaled ratio of bending to line energy, a vesicle-size-independent group for membrane contractions, and a time constant for stress relaxation. Though processing stresses ultimately relax, the crystal morphology persists well beyond the processing window.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1999

Fabrication of Pop-up Detector Arrays on Si Wafers

High sensitivity is a basic requirement for a new generation of thermal detectors. To meet the requirement, close-packed, two-dimensional silicon detector arrays have been developed in NASA Goddard Space Flight Center. The goal of the task is to fabricate detector arrays configured with thermal detectors such as infrared bolometers and x-ray calorimeters to use in space fliGht missions. This paper focuses on the fabrication and the mechanical testing of detector arrays in a 0.2 mm pixel size, the smallest pop-up detectors being developed so far. These array structures, nicknamed "PUDS" for "Pop-Up Detectors", are fabricated on I pm thick, single-crystal, silicon membranes. Their designs have been refined so we can utilize the flexibility of thin silicon films by actually folding the silicon membranes to 90 degrees in order to obtain close-packed two-dimensional arrays. The PUD elements consist of a detector platform and two legs for mechanical support while also serving as electrical and thermal paths. Torsion bars and cantilevers connecting the detector platform to the legs provide additional flexures for strain relief. Using micro-electromechanical structure (MEMS) fabrication techniques, including photolithography, anisotropic chemical etching, reactive-ion etching, and laser dicing, we have fabricated PLTD detector arrays of fourteen designs with a variation of four parameters including cantilever length, torsion bar length and width, and leg length. Folding tests were conducted to test mechanical stress distribution for the array structures. We obtained folding yields and selected optimum design parameters to reach minimal stress levels. Computer simulation was also employed to verify mechanical behaviors of PUDs in the folding process. In addition, scanning electron microscopy was utilized to examine the flatness of detectors and the alignment of detector pixels in arrays. The fabrication of thermistors and heaters on the pop-up detectors is under way, preparing us for the next step of the experiment, the thermal test.

Li, Mary J.↗

DOE OSTI2021

Exfoliation of surfactant swollen layered MWW zeolites into two-dimensional zeolite nanosheets using telechelic liquid polybutadiene

We report two-dimensional (2D) zeolites have the potential to enhance mass transport by reducing diffusion lengths and thus find applications in catalysis and separation. High aspect ratio 2D zeolite nanosheets are required for fabrication of thin, high-flux zeolite membranes. Preparation of 2D zeolite nanosheets can be achieved by exfoliation of layered zeolite precursors, which usually requires multiple steps including swelling with cationic surfactants, exfoliation by applying a mechanical force such as shearing or sonication, purification and removal of the surfactants. The exfoliation of surfactant swollen layered zeolite precursors has been studied using molten polystyrene and telechelic liquid polybutadiene, but still requires extensive shearing force. Recently, a novel one-step exfoliation method has been developed for nonswollen MWW zeolite precursors using tetrabutylammonium hydroxide (TBAOH) solution. In this work, we study the exfoliation of surfactant swollen MWW layered precursors (with and without aluminum) in commercially available liquid hydroxyl-terminated polybutadiene (HTPB) with the aim to provide fundamental understanding of the interaction between the liquid polybutadiene and the surfactant swollen layered zeolite precursors. It was found that surfactant swollen ITQ-1, (ITQ-1(S)), a pure silica layered precursor with MWW framework after being swollen with a cationic surfactant, can be exfoliated in liquid HTPB at room temperature without applying any additional shearing force. The aluminum containing surfactant swollen MWW precursors can be also exfoliated in HTPB at room temperature, but require additional shearing forces. The exfoliation process was monitored using rheology experiments and studied by tuning the composition of the zeolite precursors. The interaction between the layered zeolite precursor and the hydroxyl group of the liquid polybutadiene allows the polymer to intercalate the precursor and exfoliate it into nanosheets. The presence of framework aluminum and the nature of the organic structure directing agents (OSDAs) are key parameters affecting the exfoliation process. Framework Al is unfavorable for the exfoliation possibly due to the surface charges introduced by the aluminum. Bulky OSDA, trimethyladamantammonium (TMAda + ), in the interlayer spacing may facilitate the exfoliation.

2D nanosheets↗