Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface passivation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Chemical Passivation of Crystalline Si by Al 2 O 3 Deposited Using Atomic Layer Deposition: Implications for Solar Cells

The atomistic-level mechanism for the chemical passivation of the monocrystalline Si (c-Si) surface with thermally annealed Al 2 O 3 was studied using in situ infrared spectroscopy and photoconductance decay measurements. Al 2 O 3 was deposited on high-lifetime, float-zone c-Si substrates using atomic layer deposition (ALD) from trimethylaluminum (TMA), and H 2 O or O 3 . Surface-sensitive attenuated total reflection Fourier transform infrared spectroscopy was used to monitor the c-Si/Al 2 O 3 interface, as well as the bulk of the Al 2 O 3 film during the entire process. Our results show that some surface Si–H bonds are preserved after the ALD of Al 2 O 3 on H-terminated Si. During the annealing step at 400 °C, restructuring occurs at the c-Si/Al 2 O 3 interface to form interfacial SiO x . Isotope labeling was used to differentiate interfacial SiD bonds on the c-Si surface from H incorporated in Al 2 O 3 . Within the sensitivity of our infrared setup (~10 13 cm –2 ), we did not observe any net migration of atomic H or D from Al 2 O 3 to the c-Si/Al 2 O 3 interface. To isolate the effects of chemical and field-effect passivation of Al 2 O 3 thin films, we carried out surface passivation studies on c-Si/SiO 2 /Al 2 O 3 stacks. We also annealed these stacks in different atmospheres to test the influence of annealing atmospheres on the chemical passivation of c-Si by Al 2 O 3 and observed that O 2 -containing atmosphere led to the best surface chemical passivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Probing the Reactivity of the Active Material of a Li-Ion Silicon Anode with Common Battery Solvents

Calculations and modeling have shown that replacing the traditional graphite anode with silicon can greatly improve the energy density of lithium-ion batteries. However, the large volume change of silicon particles and high reactivity of lithiated silicon when in contact with the electrolyte lead to rapid capacity fading during charging/discharging processes. In this report, we use specific lithium silicides (LS) as model compounds to systematically study the reaction between lithiated Si and different electrolyte solvents, which provides a powerful platform to deconvolute and evaluate the degradation of various organic solvents in contact with the active lithiated Si-electrode surface after lithiation. Nuclear Magnetic Resonance (NMR) characterization results show that a cyclic carbonate such as ethylene carbonate is chemically less stable than a linear carbonate such as ethylmethyl carbonate, fluoroethylene carbonate, and triglyme as they are found to be more stable when mixed with LS model compounds. Furthermore, guided by the experimental results, two ethylene carbonate (EC)-free electrolytes are studied, and the electrochemical results show improvements with graphite-free Si electrodes relative to the traditional ethylene-carbonate-based electrolytes. More importantly, the study contributes to our understanding of the significant fundamental chemical and electrochemical stability differences between silicon and traditional graphite lithium-ion battery (LIB) anodes and suggests a focused development of electrolytes with specific chemical stability vs lithiated silicon which can passivate the surface more effectively.

25 ENERGY STORAGE↗
NASA NTRS1993

Interfacial chemistry of a perfluoropolyether lubricant studied by X-ray photoelectron spectroscopy and temperature desorption spectroscopy

The interfacial chemistry of Fomblin Z25, a commercial perfluoropolyether used as lubricant for space applications was studied with different metallic surfaces: 440C steel, gold, and aluminum. Thin layers of Fomblin Z25 were evaporated onto the oxide-free substrates, and the interfacial chemistry was studied using XPS and TDS. The reactions were induced by heating the substrate and by rubbing the substrate with a steel ball. Gold was found to be completely unreactive towards Fomblin at any temperature. Reaction at room temperature was observed only in the case of the aluminum substrate, the most reactive towards Fomblin Z25 of the substrates studied. It was necessary to heat the 440C steel substrate to 190 C to induce decomposition of the fluid. The degradation of the fluid was indicated by the formation of a debris layer at the interface. This debris layer, composed of inorganic and organic reaction products, when completely formed, passivated the surface from further attack to the Fromblin on top. The tribologically induced reactions on 440C steel formed a debris layer of similar chemical characteristics to the thermally induced layer. In all cases, the degradation reaction resulted in preferential consumption of the difluoroformyl carbon (-OCF2O-).

Herrera-Fierro, Pilar↗
NASA NTRS1992

Interfacial chemistry of a perfluoropolyether lubricant studied by XPS and TDS

The interfacial chemistry of Fomblin Z25, a commercial perfluoropolyether used as lubricant for space applications, with different metallic surfaces: 440C steel, gold and aluminum was studied. Thin layers of Fomblin Z25 were evaporated onto the oxide-free substrates and the interfacial chemistry studied using XPS and TDS. The reactions were induced by heating the substrate and by rubbing the substrate with a steel ball. Gold was found to be completely unreactive towards Fomblin at any temperature. Reaction at room temperature was observed only in the case of the aluminum substrate, the most reactive towards Fomblin Z25 of the substrates studied. It was necessary to heat the 440C steel substrate to 190 degree C to induce decomposition of the fluid. The degradation of the fluid was indicated by the formation of a debris layer at the interface. This debris layer, composed of inorganic and organic reaction products, when completely formed, passivated the surface from further attack to the Fromblin on top. The tribologically induced reactions on 440C steel formed a debris layer of similar chemical characteristics to the thermally induced layer. In all cases, the degradation reaction resulted in preferential consumption of the difluoroformyl carbon (-OCF2O-).

Herrera-Fierro, Pilar C.↗
NASA NTRS2008

Recent Progress in Characterization of Dust over Land Surfaces with Space-borne Passive Remote Sensing

Among the many components that contribute to air pollution, airborne mineral dust plays an important role due to its biogeochemical impact on the ecosystem and its radiative-forcing effect on the climate system. In East Asia, dust storms frequently accompany the cold and dry air masses that occur as part of springtime cold front systems. Outbreaks of Asian dust storms occur often in the arid and semi-arid areas of northwestern China -about 1.6x10(exp 6) square kilometers including the Gobi and Taklimakan deserts- with continuous expanding of spatial coverage. These airborne dust particles, originating in desert areas far from polluted regions, interact with anthropogenic sulfate and soot aerosols emitted from Chinese mega-cities during their transport over the mainland. Adding the intricate effects of clouds and marine aerosols, dust particles reaching the marine environment can have drastically different properties than those from their sources. Furthermore, these aerosols, once generated over the source regions, can be transported out of the boundary layer into the free troposphere and can travel thousands of kilometers across the Pacific into the United States and beyond. In this paper, we will demonstrate the capability of a new satellite algorithm to retrieve aerosol properties (e.g., optical thickness, single scattering albedo) over bright-reflecting surfaces such as urban areas and deserts. Such retrievals have been difficult to perform using previously available algorithms that use wavelengths from the mid-visible to the near IR because they have trouble separating the aerosol signal from the contribution due to the bright surface reflectance. This new algorithm, called Deep Blue, utilizes blue-wavelength measurements from instruments such as SeaWiFS and MODIS to infer the properties of aerosols, since the surface reflectance over land in the blue part of the spectrum is much lower than for longer wavelength channels. Reasonable agreements have been achieved between Deep Blue retrievals of aerosol optical thickness and those directly from AERONET sunphotometers over desert and semi-desert regions. New Deep Blue products will allow scientists to determine quantitatively the aerosol properties near sources using high spatial resolution measurements from SeaWiFS and MODIS-like instruments. Long-term satellite measurements (1998 - 2007) from SeaWiFS will be utilized to investigate the interannual variability of source, pathway, and dust loading associated with the Asian dust storm outbreaks. In addition, monthly averaged aerosol optical thickness during the springtime from SeaWiFS will also be compared with the MODIS Deep Blue products.

Hsu, N. Christina↗
NASA NTRS2007

Remote Sensing of Terrestrial Water Storage and Application to Drought Monitoring

Terrestrial water storage (TWS) consists of groundwater, soil moisture and permafrost, surface water, snow and ice, and wet biomass. TWS variability tends to be dominated by snow and ice in polar and alpine regions, by soil moisture in mid-latitudes, and by surface water in wet, tropical regions such as the Amazon (Rodell and Famiglietti, 2001; Bates et al., 2007). Drought may be defined as a period of abnormally dry weather long enough to cause significant deficits in one or more of the TWS components. Thus, along with observations of the agricultural and socioeconomic impacts, measurements of TWS and its components enable quantification of drought severity. Each of the TWS components exhibits significant spatial variability, while installation and maintenance of sufficiently dense monitoring networks is costly and labor-intensive. Thus satellite remote sensing is an appealing alternative to traditional measurement techniques. Several current remote sensing instruments are able to detect variations in one or more TWS variables, including the Advanced Microwave Scanning Radiometer (AMSR) on NASA's Aqua satellite and the Moderate Resolution Imaging Spectroradiometer (MODIS) on NASA's Terra and Aqua. Future satellite missions have been proposed to improve this capability, including the European Space Agency's Soil Moisture Ocean Salinity mission (SMOS) and the Soil Moisture Active Passive (SMAP), Surface Water Ocean Topography (SWOT), and Snow and Cold Land Processes (SCLP) missions recommended by the US National Academy of Science's Decadal Survey for Earth Science (NRC, 2007). However, only one remote sensing technology is able to monitor changes in TWS from the land surface to the base of the deepest aquifer: satellite gravimetry. This paper focuses on NASA's Gravity Recovery and Climate Experiment mission (GRACE; http://www.csr.utexas.edu/grace/) and its potential as a tool for drought monitoring.

Rodell, Matt↗
DOE OSTI2021

A hybrid CoOOH-rGO/Fe 2 O 3 photoanode with spatial charge separation and charge transfer for efficient photoelectrochemical water oxidation

As a promising photoanode for photoelectrochemical (PEC) water oxidation, hematite (Fe 2 O 3 ) still suffers from poor charge mobility and serious charges recombination and sluggish surface oxygen evolution kinetics. Herein, a hybrid photoanode of cobalt (oxy)hydroxide coupled with reduced graphene oxide modified Fe 2 O 3 (CoOOH-rGO/Fe 2 O 3 ) is well crafted by a facile hydrothermal synthesis with a chelation-mediated in-situ growth method. Morphology characterizations indicate rGO forms the internal network among isolated Fe 2 O 3 and CoOOH nanosheets distribute on the terminal of Fe 2 O 3 , forming a spatial separated nanostructure. The resultant CoOOH-rGO/Fe 2 O 3 exhibits an obviously reduced onset potential of ca. 150 mV and a significantly enhanced photocurrent density of 2.56 mA cm -2 at 1.23 V, which is ca. 3.3 times higher than that of bare Fe 2 O 3 . Especially, the functions of rGO and CoOOH are studied by using electrochemical impedance spectroscopy, open circuit potentials and intensity modulated photocurrent spectroscopy. It is found rGO act as conductive network which facilitates the electron transfer from Fe 2 O 3 to the substrate, while CoOOH evidently passivate the surface states of Fe 2 O 3 , improve charge separation and provide catalytic active sites for water oxidation. Additionally, the spatial charge separation and charge transfer caused by CoOOH and rGO are responsible for the enhanced PEC performance of water oxidation. The rational design and the facile fabrication strategy exhibit great potential to be used for other PEC system with great efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Blade Coating Inverted Perovskite Solar Cells with Vacuum-Assisted Nucleation Based on Bottom Quasi-2D Passivation

Metal halide perovskite solar cells (PSCs) attract an enormous attention because of their high power conversion efficiency (PCE) and low fabrication cost. However, their commercialization is limited by fabricating highly efficient large-area solar cells. Controlling the morphology and crystallization of perovskite for large-area fabrication is difficult but important. Here, in this work, a vacuum-assisted approach is developed to obtain mirror-like, pinhole-free, highly crystalline, and uniform blade-coated perovskite films, without the use of antisolvent and air knife. This method can be a universal approach for various perovskite compositions. Meanwhile, the phenethylammonium iodide passivation effect at the top and bottom interfaces of perovskite layer based on FTO/NiO x /perovskite/C 60 /BCP/Cu inverted p-i-n structure is systematically investigated. The optimized device fabricated by blade coating under an ambient environment exhibits the champion PCE of 20.7% and is among the top few records of blade coating inverted structure based on NiOx hole transport layer. The encapsulated device retains 97% of its maximum efficiency under open-circuit condition after 1000 h of photostability test in an ambient environment at room temperature with a relative humidity of 40–60%. Herein, low-cost, easy, and reproducible strategies to fabricate efficient and stable blade-coated PSCs are demonstrated.

14 SOLAR ENERGY↗
NASA NTRS1994

Ice surface temperature retrieval from AVHRR, ATSR, and passive microwave satellite data: Algorithm development and application

One essential parameter used in the estimation of radiative and turbulent heat fluxes from satellite data is surface temperature. Sea and land surface temperature (SST and LST) retrieval algorithms that utilize the thermal infrared portion of the spectrum have been developed, with the degree of success dependent primarily upon the variability of the surface and atmospheric characteristics. However, little effort has been directed to the retrieval of the sea ice surface temperature (IST) in the Arctic and Antarctic pack ice or the ice sheet surface temperature over Antarctica and Greenland. The reason is not one of methodology, but rather our limited knowledge of atmospheric temperature, humidity, and aerosol vertical, spatial and temporal distributions, the microphysical properties of polar clouds, and the spectral characteristics of snow, ice, and water surfaces. Over the open ocean the surface is warm, dark, and relatively homogeneous. This makes SST retrieval, including cloud clearing, a fairly straightforward task. Over the ice, however, the surface within a single satellite pixel is likely to be highly heterogeneous, a mixture of ice of various thicknesses, open water, and snow cover in the case of sea ice. Additionally, the Arctic is cloudy - very cloudy - with typical cloud cover amounts ranging from 60-90 percent. There are few observations of cloud cover amounts over Antarctica. The goal of this research is to increase our knowledge of surface temperature patterns and magnitudes in both polar regions, by examining existing data and improving our ability to use satellite data as a monitoring tool. Four instruments are of interest in this study: the AVHRR, ATSR, SMMR, and SSM/I. Our objectives are as follows. Refine the existing AVHRR retrieval algorithm defined in Key and Haefliger (1992; hereafter KH92) and applied elsewhere. Develop a method for IST retrieval from ATSR data similar to the one used for SST. Further investigate the possibility of estimating surface temperature from passive microwave data (in conjunction with AVHRR clear sky samples) through the use of 'effective emissivities' and physical relationships between skin temperature and subsurface temperature. Use the general method outlined in MK93 to calculate a 12-year record of clear sky equivalent surface temperatures, or possibly all-sky snow-ice interface physical temperatures, from SMMR and SSM/I, compare these temperatures to climatologies, ECMWF modeled surface temperatures, and surface temperatures predicted by a 2-D ice model. And intercompare several ice surface retrieval methods and validate them against ground measurements from the Swiss Camp on the Greenland ice sheet. Additionally, we intend to develop a surface temperature product based on AVHRR data and possibly blended with drifting buoy and meteorological station temperatures.

Key, Jeff↗
DOE OSTI2020

Laser Crystallization and Dopant Activation of a-Si:H Carrier-Selective Layer in TOPCon Si Solar Cells

Herein, we present a pulsed-laser processing method for crystallization and dopant activation of a highly n-doped amorphous silicon (a-Si:H) carrier-selective layer in a tunnel oxide passivated contact (TOPCon) Si solar cell structure. Here, the laser method provides enhanced conductivity and implied open circuit voltage while reducing emitter saturation current density and surface heating, as opposed to conventional high-temperature furnace annealing of the bulk Si wafer with a TOPCon structure. We identify an appropriate laser wavelength, fluence, and layer thickness using modeling and simulations. Raman and Hall effect measurements demonstrate increased crystallinity and dopant activation, whereas photoconductive decay shows enhanced surface and interface passivation quality. Additionally, we examine the role of subsequent SiNx deposition on further improving the passivation of laser-processed TOPCon layers to achieve a 5.9 kΩ/sq film sheet resistance, 2 ms effective carrier lifetime, 718 mV implied open-circuit voltage (iVOC), and 8.6 fA/cm 2 one-side recombination current density (J0) with the potential for further passivation improvement via laser process and a-Si layer thickness optimization.

14 SOLAR ENERGY↗
DOE OSTI2024

Covalently-Bonded Laminar Assembly of Van der Waals Semiconductors with Polymers: Toward High-Performance Flexible Devices

Van der Waals semiconductors (vdWS) offer superior mechanical and electrical properties and are promising for flexible microelectronics when combined with polymer substrates. However, the self-passivated vdWS surfaces and their weak adhesion to polymers tend to cause interfacial sliding and wrinkling, and thus, are still challenging the reliability of vdWS-based flexible devices. Here, in this study, an effective covalent vdWS–polymer lamination method with high stretch tolerance and excellent electronic performance is reported. Using molybdenum disulfide (MoS 2 ) and polydimethylsiloxane (PDMS) as a case study, gold–chalcogen bonding and mercapto silane bridges are leveraged. The resulting composite structures exhibit more uniform and stronger interfacial adhesion. This enhanced coupling also enables the observation of a theoretically predicted tension-induced band structure transition in MoS 2 . Moreover, no obvious degradation in the devices’ structural and electrical properties is identified after numerous mechanical cycle tests. This high-quality lamination enhances the reliability of vdWS-based flexible microelectronics, accelerating their practical applications in biomedical research and consumer electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cross-scale modeling and experimental integration for advancing cathode electrolyte interphase studies in high energy density lithium-ion batteries

Electrochemical interfaces are critical to the performance and durability of lithium-ion batteries (LIBs). The solid electrode-electrolyte interphase (SEI and CEI) structures that form during cycling can passivate reactive surfaces, ensuring safe operation, but also may contribute to performance degradation. Understanding the microscopic factors influencing interphase formation, growth, and evolution is essential for balanced battery design. While significant research has focused on the anode-electrolyte interphase (SEI), the cathode-electrolyte interphase (CEI) remains less explored, despite its importance in high-voltage and advanced battery technologies. Challenges in conducting in-situ or operando experiments arise from the occluded nature of these interfaces and the long timescales involved, often leading to biased interpretations. A validated multi-scale, multi-physics modeling approach, integrated with advanced characterization techniques, can effectively elucidate the intrinsic stability of electrolyte and cathode surfaces, the impact of chemical heterogeneity, and the role of microstructural features on CEI performance. In conclusion, this article reviews current modeling and simulation strategies for studying CEI in advanced LIBs and highlights opportunities for future methodological advancements and experimental integration.

Cathode-electrolyte interphase↗
DOE OSTI2021

A refined design concept for sulfur-tolerant Pd catalyst supported on zeolite by shape-selective exclusion and hydrogen spillover for hydrogenation of aromatics

Sulfur poisoning of noble metal catalysts has been a major challenge for decades. This work demonstrates the superior sulfur tolerance of a hybrid zeolite-supported Pd catalyst for hydrogenation of tetralin containing benzothiophene. The hybrid catalyst consists of Pd supported on a large-pore acidic zeolite Y (Pd/HY) and a small-pore zeolite A without (Pd/HA) or with surface metal passivation by chemical vapor deposition of SiO 2 (SiO 2 -Pd/HA) and with potassium ion exchange (SiO 2 -Pd/KA). Pd/HY is very active for tetralin hydrogenation but quickly deactivates after exposure to benzothiophene at high concentration of 100 ppm sulfur. The SiO 2 -coated Pd/HA shows no activity for tetralin hydrogenation, but continues to activate H 2 and serve as a source of hydrogen spillover from Pd/HA since these metal sites are protected from thiophenic sulfur due to size-selective exclusion. Adding K ion-exchanged and SiO 2 -coated catalyst SiO 2 -Pd/KA to Pd/HY is even more effective for enhancing sulfur tolerance, both for tetralin hydrogenation and for isomerization of cis-decalin to trans-decalin in the presence of benzothiophene. The turnover frequencies (TOF) of all the catalysts are similar at the exposed sulfur/Pd atomic ratio of around 0.5. With further increase in sulfur/Pd ratio, rapid decline in TOF was observed on Pd/HY, but SiO 2 -Pd/KA + Pd/HY hybrid catalyst shows a significantly higher TOF than that over Pd/HY, even though SiO 2 -Pd/KA or SiO 2 -Pd/HA alone shows no TOF for tetralin hydrogenation. Even after high-dose poisoning at 400 ppm sulfur, the SiO 2 -Pd/KA + Pd/HY hybrid recovered activity more quickly than SiO 2 -Pd/HA + Pd/HY, while the latter in turn is much better than Pd/HY alone. These results point to the higher activity for hydrogen spillover from SiO 2 -Pd/KA where Pd metal sites are protected from not only thiophenic sulfur but also inorganic sulfur H 2 S by shape-selective exclusion. The present work further establishes the validity of shape-selective exclusion and hydrogen spillover in the design concept proposed for a sulfur-tolerant bimodal acidic zeolite-supported metal catalyst for hydrogenation of naphthalene [C.S. Song, Chemtech, 29 (1999) 26–30], and refines the design concept further for limiting the size of small pore in hybrid catalysts to~3 Å for restricting access of H 2 S but allowing entrance of H 2 . Further, this refined design concept is applicable to other supported monometallic and bimetallic catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhancing the performance of the perovskite solar cells by modifying the SnO 2 electron transport layer

The tin oxide (SnO 2 ) electron transport layer (ETL) plays a vital role in the photo-conversion efficiency (PCE) and stability of organic-inorganic perovskite solar cells (PSCs). However, SnO 2 ETL-induced defects such as hydroxyl groups, oxygen vacancies, exposed Sn atoms, and dangling bonds hinder device performance. In this study, rubidium chloride (RbCl) has been used to modify the SnO 2 ETL. Perovskite film formed on the RbCl-modified SnO 2 ETL exhibits improved crystallinity with enlarged grain size and reduced grain boundaries and enhanced optical absorption. Further, the Hall-effect measurements indicate the improved carrier mobility, and the dark J-V curve shows the increment of electrical conductivity for the RbCl-modified SnO 2 ETL. X-ray photoelectron spectroscopy (XPS) results demonstrate the surface defects passivation of the perovskite layer by modifying the SnO 2 ETL. A champion PCE of 19.35% has been achieved for the RbCl-modified SnO 2 ETL-based devices with improved stability, while the control devices with unmodified SnO 2 ETL show a PCE of 17.18%.

14 SOLAR ENERGY↗
DOE OSTI2020

Interfacial engineering for stabilizing polymer electrolytes with 4V cathodes in lithium metal batteries at elevated temperature

Poly (ethylene oxide) (PEO) polymer electrolytes are promising candidates for next-generation rechargeable lithium batteries. However, the poor interfacial stability between 4 V cathodes and PEO electrolytes impedes their applications in 4 V lithium batteries with high energy density. Here, we demonstrate a facile and effective strategy to enhance the interfacial stability by the synergy of Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) coating on the cathode surface, and salt combination in the electrolyte, even with a cut-off voltage of 4.25–4.4 V vs. Li + /Li. Nano-LAGP coated Li|PEO|LiCoO 2 cell delivers stable cycling with a capacity retention of 81.9%/400 cycles and 84.7%/200 cycles at 60 °C when charged to 4.25 and 4.3 V in pure polyether electrolyte, respectively. Steady cycling is also demonstrated at room temperature and with LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523) cathode. This work offers a viable and scalable approach to improve the stability between PEO electrolytes and 4 V cathodes and open up new possibilities for practical application of 4 V lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Robust Unencapsulated Perovskite Solar Cells Protected by a Fluorinated Fullerene Electron Transporting Layer

The emergent perovskite photovoltaics technology faces challenges like the long-term durability combining moisture, thermal, and photo stresses that prevents them from competing with established technologies. In this work, we introduce a series of new fluorinated fullerenes as an electron-transporting layer (ETL) for robust perovskite photovoltaics that deliver a high power conversion efficiency of 21.27% with substantially improved durability against environmental stressing. The hydrophobic nature of the new fullerene protects the unencapsulated perovskite cell with stability over 1400 h in 85% relative humidity. Notably, the unencapsulated device maintained 80% of their original performance (T-80) after being immersed in water for over 10 min. Detailed characterizations suggest that the fluorinated fullerene can immobilize the cations in perovskites and passivate the surface traps. Therefore, the T-80 lifetime of the devices under constant illumination reached 1920 h. On the basis of the accelerated test, we estimate a lifetime approaching 10 years with encapsulation. The successful demonstration of the new ETL can stimulate further research and momentum for future photovoltaic technology development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗