Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Comparing the Purity of Rolled versus Evaporated Lithium Metal Films Using X-ray Microtomography

Here, we present a comparison of lithium metal films produced via rolling and thermal evaporation using synchrotron hard X-ray microtomography. In past studies of rolled lithium metal foils, a large number of C, O, and N impurities were found and identified as the key cause for failure in lithium metal cells. In this comparison, the X-ray tomography data show that the evaporated lithium metal films have an average impurity concentration of 19 particles/mm3 in comparison to 1350 particles/mm3 in the rolled lithium metal. An analysis of the inner substrate/lithium interface and outer lithium surface of the thermally evaporated film shows a much greater concentration of impurities at these interfaces, further emphasizing the importance of interface engineering in producing high-quality lithium metal batteries. Furthermore, we show that, if surface contamination can be avoided, it is possible to obtain lithium films with no impurities detectable by synchrotron hard X-ray tomography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Experimental Investigation of Sweeping Jet Film Cooling in a Transonic Turbine Cascade

Abstract The sweeping jet (SJ) film cooling hole has shown promising cooling performance compared to the standard shaped hole in low-speed conditions. The present work demonstrates the first attempt of SJ film cooling at an engine relevant Mach number. An experimental investigation was conducted to study the SJ film cooling on a nozzle guide vane suction surface. A well-established additive manufacturing technique commonly known as stereolithography (SLA) was utilized to design a transonic, engine representative vane geometry in which a row of SJ holes was used on the vane suction surface. Experiments were performed in a linear transonic cascade at an exit Mach number of 0.8 and blowing ratios of BR = 0.25–2.23. The measurement of heat transfer was conducted with the transient IR method, and the convective heat transfer coefficient (HTC) and adiabatic film cooling effectiveness were estimated using a dual linear regression technique (DLRT). Aerodynamic loss measurements were also performed with a total pressure Kiel probe at 0.25Cax downstream of the exit plane of the vane cascade. Experiments were also conducted for a baseline-shaped hole (777-hole) for a direct comparison. Results showed that the SJ hole has a wider coolant spreading in the lateral direction near the hole exit due to its sweeping motion that improves the overall cooling performance particularly at high blowing ratios (BR > 1). Aerodynamic loss measurement suggested that the SJ hole has a comparable total pressure loss to the 777-shaped hole.

Engineering↗
DOE OSTI2022

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple–Conducting Oxides for Protonic Ceramic Electrochemical Cells

Porous electrodes that conduct electrons, protons, and oxygen ions with dramatically expanded catalytic active sites can replace conventional electrodes with sluggish kinetics in protonic ceramic electrochemical cells. In this work, a strategy is utilized to promote triple conduction by facilitating proton conduction in praseodymium cobaltite perovskite through engineering non-equivalent B-site Ni/Co occupancy. Surface infrared spectroscopy is used to study the dehydration behavior, which proves the existence of protons in the perovskite lattice. The proton mobility and proton stability are investigated by hydrogen/deuterium (H/D) isotope exchange and temperature-programmed desorption. It is observed that the increased nickel replacement on the B-site has a positive impact on proton defect stability, catalytic activity, and electrochemical performance. This doping strategy is demonstrated to be a promising pathway to increase catalytic activity toward the oxygen reduction and water splitting reactions. The chosen PrNi 0.7 Co 0.3 O 3–δ oxygen electrode demonstrates excellent full-cell performance with high electrolysis current density of –1.48 A cm –2 at 1.3 V and a peak fuel-cell power density of 0.95 W cm –2 at 600 °C and also enables lower-temperature operations down to 350 °C, and superior long-term durability.

08 HYDROGEN↗
DOE OSTI2023

In situ Stress Monitoring Reveals Tension and Wrinkling Evolutions during Halide Perovskite Film Formation

Metal halide perovskites (MHPs) are promising candidates for next-generation thin film photovoltaics and high-performance tandems. Solution-processed MHP films are susceptible to residual stress that can induce undesirable surface wrinkles. However, the origins and evolution of stress during solution processing remain elusive. Here, in this work, we utilize multimodal in situ characterizations, including substrate curvature, reflectance, absorbance, and photoluminescence, to monitor stress and morphology evolution during MHP film formation. A film formation model emerges, consisting of a perovskite top crust on a semirigid sol with the ability to transfer mechanical forces. The phase transformation induces tension in the MHP crust, while shrinkage of the sol causes additional compression and surface wrinkles. Wrinkle-free films are formed through dynamically balancing forces between the crust and the sol. This study provides a powerful toolkit for the fast-growing area of stress engineering in MHP photovoltaics to achieve dynamic control of film stress and surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Geometric prior of multi-resolution yielding manifolds and the local closest point projection for nearly non-smooth plasticity

Elastoplasticity models often introduce a scalar-valued yield function to implicitly represent the boundary between elastic and plastic material states. Here this paper introduces a new alternative where the yield envelope is represented by a manifold of which the topology and the geometry are learned from a set of data points in a parametric space (e.g. principal stress space, π-plane). Here, deep geometric learning enables us to reconstruct a highly complex yield envelope by breaking it down into multiple coordinate charts. The global atlas that consists of these coordinate charts in return allows us to represent the yield surface via multiple overlapping patches, each with a specific local parametrization. This setup provides several advantages over the classical implicit function representation approach. For instance, the availability of coordinate charts enables us to introduce an alternative stress integration algorithm where the trial stress may project directly on a local patch and hence circumvent the issues related to non-smoothness and the lack of convexity of yield surfaces. Meanwhile, the local parametric approach also enables us to predict hardening/softening locally in the parametric space, even without complete knowledge of the yield surface. Comparisons between the classical yield function approach on the non-smooth plasticity and anisotropic cam-clay plasticity model are provided to demonstrate the capacity of the models for highly precise yield surface and the feasibility of the implementation of the learned model in the local stress integration algorithm.

42 ENGINEERING↗
DOE OSTI2023

Increased localization of Majorana modes in antiferromagnetic chains on superconductors

Magnet-superconductor hybrid (MSH) systems are a key platform for custom-designed topological superconductors. Ideally, the ends of a one-dimensional MSH structure will host Majorana zero-modes (MZMs), the fundamental unit of topological quantum computing. However, some experiments with ferromagnetic (FM) chains show a more complicated picture. Due to tiny gap sizes and hence long coherence lengths, MZMs might hybridize and lose their topological protection. Recent experiments on a niobium surface have shown that both FM and antiferromagnetic (AFM) chains may be engineered, with the magnetic order depending on the crystallographic direction of the chain. While FM chains are well understood, AFM chains are less so. Here, we study two models inspired by the niobium surface: A minimal model to elucidate the general topological properties of AFM chains and an extended model to more closely simulate a real system by mimicking the proximity effect. Here, we find that, in general, for AFM chains, the topological gap is larger than for FM ones, and thus, coherence lengths are shorter for AFM chains, yielding more pronounced localization of MZMs in these chains. While for some parameters AFM chains may be topologically trivial, we find in these cases that adding an adjacent chain can result in a nontrivial system, with a single MZM at each chain end.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Hydropower Geotechnical Foundations: Current Practice and Innovation Opportunities for Low-Head Applications

Hydropower is a renewable energy resource that produces electricity from flowing water under pressure. Engineered hydropower structures, such as dams, are used to create a hydraulic head, enabling a turbinegenerator unit to convert pressurized flow into electricity. While hydropower has been a source of renewable energy since antiquity, new development in the United States has slowed in recent decades. Based on recent resource assessments, the largest opportunity to expand hydropower in the United States is from new stream-reach development (i.e., new hydropower development along stream-reaches that do not currently have hydroelectric facilities or other forms of infrastructure, such as dams). Roughly 75% of identified new stream-reach development potential is from low-head sites (less than 30 ft of head), which typically suffer from smaller power densities and higher normalized costs, given economies of scale. Hydropower developers and other stakeholders are thus interested in strategies to reduce initial capital costs while practicing sustainable development to maximize environmental compatibility with minimal disruption to natural aquatic life, sediment, and water flows. Historically, civil works have represented a significant cost driver for new hydropower development, with the foundation system representing a major cost component and source of uncertainty. The foundation system is the collection of engineered structural features (e.g. cutoff trenches, walls, grouting, anchors) constructed at or below the preconstruction ground surface that interfaces between the overlying structures (superstructures) and the bed material below (subsurface). Development of a hydropower foundation system must consider the various characteristics of the surrounding stream environment and subsurface while adhering to the engineering requirements of the superstructure that it supports. The care of water, excavation, and other construction activities are important features of foundation design and construction. The design and construction cost of the foundation system is largely dependent on the site geology and riverbed composition and is influenced by the level of geotechnical assessment required and conducted. Thus, a hydropower facility’s geotechnical foundation is often highly site-specific, with proper site selection and assessment being important to project success. The foundation system is designed to provide structural stability (of the foundation and dam), limit seepage, ensure public safety, and maintain functionality for the project life, during both construction and facility operations. Inadequate foundation or dam design can result in dam failure and the uncontrolled release of significant volumes of water, which could cause a high number of casualties and extensive property damage downstream of the failure. According to the Association of State Dam Safety Officials, approximately 30% of all historical dam failures in the United States are attributed to foundation or abutment defects, and another 20% are attributed to piping or seepage through the embankment, foundation, or abutment. To ameliorate these safety considerations, foundations often require massive amounts of construction material (e.g., grout, concrete, engineered dam fill) and long construction times. Foundation design also requires significant analysis prior to construction because the initial in-stream and abutment subsurface conditions are site-specific, and sufficient data for them often are lacking. Current practice requires on-site assessment, using expensive drilling and invasive and non-invasive investigation methods, to determine the expected cost of foundation material and treatment. Additionally, foundation construction often requires site dewatering (and other care of water activities), which involves constructing temporary diversion structures upstream and often downstream, called cofferdams, and water diversion systems that route water around the construction site. Cofferdams and water diversion systems can drastically increase construction costs and contribute to environmental disruption, including modification of flow patterns and benthic habitats. Given the technical, economic, and environmental challenges associated with hydropower foundations, opportunities exist to improve the current state of practice and to develop new and innovative solutions to Hydropower is a renewable energy resource that produces electricity from flowing water under pressure. Engineered hydropower structures, such as dams, are used to create a hydraulic head, enabling a turbinegenerator unit to convert pressurized flow into electricity. While hydropower has been a source of renewable energy since antiquity, new development in the United States has slowed in recent decades. Based on recent resource assessments, the largest opportunity to expand hydropower in the United States is from new stream-reach development (i.e., new hydropower development along stream-reaches that do not currently have hydroelectric facilities or other forms of infrastructure, such as dams). Roughly 75% of identified new stream-reach development potential is from low-head sites (less than 30 ft of head), which typically suffer from smaller power densities and higher normalized costs, given economies of scale. Hydropower developers and other stakeholders are thus interested in strategies to reduce initial capital costs while practicing sustainable development to maximize environmental compatibility with minimal disruption to natural aquatic life, sediment, and water flows. Historically, civil works have represented a significant cost driver for new hydropower development, with the foundation system representing a major cost component and source of uncertainty. The foundation system is the collection of engineered structural features (e.g. cutoff trenches, walls, grouting, anchors) constructed at or below the preconstruction ground surface that interfaces between the overlying structures (superstructures) and the bed material below (subsurface). Development of a hydropower foundation system must consider the various characteristics of the surrounding stream environment and subsurface while adhering to the engineering requirements of the superstructure that it supports. The care of water, excavation, and other construction activities are important features of foundation design and construction. The design and construction cost of the foundation system is largely dependent on the site geology and riverbed composition and is influenced by the level of geotechnical assessment required and conducted. Thus, a hydropower facility’s geotechnical foundation is often highly site-specific, with proper site selection and assessment being important to project success. The foundation system is designed to provide structural stability (of the foundation and dam), limit seepage, ensure public safety, and maintain functionality for the project life, during both construction and facility operations. Inadequate foundation or dam design can result in dam failure and the uncontrolled release of significant volumes of water, which could cause a high number of casualties and extensive property damage downstream of the failure. According to the Association of State Dam Safety Officials, approximately 30% of all historical dam failures in the United States are attributed to foundation or abutment defects, and another 20% are attributed to piping or seepage through the embankment, foundation, or abutment. To ameliorate these safety considerations, foundations often require massive amounts of construction material (e.g., grout, concrete, engineered dam fill) and long construction times. Foundation design also requires significant analysis prior to construction because the initial in-stream and abutment subsurface conditions are site-specific, and sufficient data for them often are lacking. Current practice requires on-site assessment, using expensive drilling and invasive and non-invasive investigation methods, to determine the expected cost of foundation material and treatment. Additionally, foundation construction often requires site dewatering (and other care of water activities), which involves constructing temporary diversion structures upstream and often downstream, called cofferdams, and water diversion systems that route water around the construction site. Cofferdams and water diversion systems can drastically increase construction costs and contribute to environmental disruption, including modification of flow patterns and benthic habitats. Given the technical, economic, and environmental challenges associated with hydropower foundations, opportunities exist to improve the current state of practice and to develop new and innovative solutions to challenges frequently encountered with traditional approaches. With this understanding, it is critically important to understand and document the current state of practice for hydropower geotechnical foundations, identify key challenges, and define opportunities for innovative solutions. To this end, this report documents the current state of practice across the three main phases of geotechnical foundation development: (1) geotechnical site assessment, (2) design, and (3) construction for hydropower systems. It also describes the major challenges with conventional approaches and identifies opportunities for innovation to reduce hydropower foundations costs, timelines, and risks. Key takeaways from this report include the following: Approximately 80% of available low-head sites are expected to have foundations on soil beds rather than rock beds, suggesting that rockfill and earthfill dams may be the most cost-effective conventional dam type for new projects.; Geotechnical and geologic investigation activities are time-consuming and expensive but are essential to define the parameters and criteria needed for foundation design.; Certain riverbed soil and bedrock types present significant technical challenges or require expensive foundation construction, which can prove financially prohibitive for low-head project development.; Modular hydropower design and prefabricated modular foundations represent a promising but unproven paradigm for new hydropower development. Design and construction approaches using optimized and highly repeatable, reliable components would benefit project cost, time, and risk but require additional research and development.; Temporary construction features for foundations, including cofferdams, water diversion, and water control systems, can prove costly and have inherent construction risk.; For economically viable development, hydropower geotechnical foundations should be limited to 4 to 15% of the project’s total initial capital costs. Many proposed projects have experienced cost overruns attributable to foundation difficulties or surprises during construction. These overruns may have been due to inadequate investigations, lack of adequate engineering effort to tailor the structures to site geology and topography, and/or contractual terms, among other considerations.; Challenges for hydropower foundations and opportunities for innovative technology solutions are identified in the following areas (consistent with the three main phases of foundation development): Geotechnical site assessment, Foundation design and materials, Construction methods and technology. Ultimately, this report aims to provide information about geotechnical foundations for low-head hydropower and to motivate transformative technologies to support hydropower growth.

13 HYDRO ENERGY↗
DOE OSTI2022

On the surface passivating principle of functional thiol towards efficient and stable perovskite nanocrystal solar cells

Inorganic halide perovskite nanocrystals (PNCs) have demonstrated promising potential for solar cell applications. However, the lability of photoactive CsPbI3 phase under ambient conditions, coupled with considerable amounts of surface defects induced during solidification process, have impeded achieving high performances and longevities of the PNC-based solar cells. Post-treatment of the PNCs with organic ligands has been proposed as an efficient strategy for surface passivation, which, however, still relies on the binding actions of typical functional groups towards surface defects (especially, carboxylates onto iodine vacancies). Herein, we uncover that thiolate, a deprotonated form of thiol, renders distinctive binding feasibility towards iodine vacancies at the CsPbI3 PNC surface, compared with those of typical functional groups. By treating the PNC solid with deprotonated cysteine as a ligand, the surface defects are comprehensively passivated. The solar cells with the modified PNC films demonstrate an excellent PCE of 15.5 % and improved device longevity (77 % of initial PCE over 2 months) under ambient conditions. Our work not only elucidates the chemical principles of thiol on the binding with PNC surface, but also corroborates the power of thiolate as a promising strategy to develop high performances and improved longevity of solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Numerical simulation of falling film sensible heat transfer over round horizontal tubes

Numerical simulations are performed to explore the heat transfer characteristics of falling films over horizontal round tubes with uniform heat flux imposed for a range of Reynolds numbers spanning the droplet, jet, and sheet regimes. Simulations results agree well with available experimental measurements. The study analyzes the local as well as average heat transfer behavior under the different flow modes. The numerical results show that the local Nusselt number (Nu) distribution depends on the flow features in each mode and varies substantially in all directions for the respective mode. In the droplet mode, the Nu value varies significantly as the droplet impinges and the remnant liquid-bridge retracts (peak instantaneous Nu near 6), followed by wave propagation over the tube surface with peak Nu around 0.25. For the jet modes, the local maximum in the heat transfer occurs off-center to the impingement location with magnitudes of peak Nu = 3.1 for the inline jet mode and Nu = 2.7 for the staggered jet mode, while on the rest of the tube surface, it has an inverse relation with the liquid film thickness. Substantial variations in the heat transfer value are also recorded in the middle of the two impinging jets with Nu = 0.95 in the inline jet mode where the neighboring jets do not interact, and Nu = 0.60 in the crest region of the staggered jet mode where the neighboring jets interact with each other. In the sheet mode, the Nu was seen to depend on the thickness of the liquid waves traversing over the tube surface. Lower Nu values were recorded beneath the crest location of the liquid waves, which increases (1.4–11.6% depending on circumferential location) abruptly in magnitude at the advancing fronts of the waves. The temperature distribution in the liquid film in each of the modes was examined to evaluate the mechanism of heat transfer process. This study also compares the local heat transfer coefficient distribution with the analytical heat transfer models derived to predict heat transfer performance over horizontal tube surfaces.

42 ENGINEERING↗
DOE OSTI2025

Microstructurally Strained Pyrochlore–Perovskite Biphasic Electrocatalysts for the Oxygen Evolution Reaction

Efficiency of water splitting for hydrogen production is often limited by the sluggish kinetics of multiple electronic transfers required in the heterogeneous oxygen evolution reaction (OER). Catalyst design for reducing the high OER overpotential remains a major scientific challenge. Lattice-strain engineering, a method for tuning the electronic structure and surface geometric configuration of active sites, may greatly affect the interaction between adsorbates and catalytic surfaces for high activity and stability. Here, in this study, we present the synthesis of biphasic oxides of YPrSrRuMnO x , which consists of distinct phases of Y 2 Ru 2 O 7 pyrochlore and (Pr 0.7 Sr 0.3 )MnO 3 perovskite, and the development of a suitable analytical approach to study the strain–catalytic property relationship. Linear sweep voltammetry results reveal that the biphasic oxide exhibits approximately 3.1 times greater mass activity and 2.4 times larger turnover frequency (TOF) than single-phase Y 2 Ru 2 O 7 in the 0.1 M HClO 4 electrolyte. The biphasic catalyst is also about 3 times more stable than the single-phase oxide under acidic conditions. X-ray photoelectron spectroscopy, nitrogen isotherm, and electrochemical surface area analyses indicate that the oxidation state, specific surface area, and electrochemical surface area do not cause enough difference in the observed enhancement of OER performance. We examined the effects of microstrain on electrocatalysis, originating from lattice mismatch between different phases, using three different structural models. Specifically, we compared the Williamson–Hall method, standard stress–strain analysis, and Rietveld refinement in analyzing the structure–property relationship. Strain mapping using geometric phase analysis (GPA) further revealed significant microstrain and lattice dislocations localized near phase boundaries in the biphasic oxide, in contrast to the uniform strain in single-phase materials. The results reveal that the increased microstrain correlates well with the improved OER performance, as the biphasic oxide catalyst exhibits 2–3 times greater microstrain than Y 2 Ru 2 O 7 pyrochlore.

electrocatalysts↗
DOE OSTI2022

Synthesis of La 2–x Sr x CuO 4 films via atomic layer-by-layer molecular beam epitaxy

Atomic layer-by-layer molecular beam epitaxy (ALL-MBE) is a sophisticated technique to synthesize high-temperature superconductor (HTS) materials. ALL-MBE produces single-crystal HTS films with atomically smooth surfaces and interfaces, as well as precise multilayer heterostructures engineered down to a single atomic layer level. This enables the fabrication of tunnel junctions, nanowires, nanorings, and other HTS devices of interest. Our group has focused on ALL-MBE synthesis and materials science of La 2–x Sr x CuO 4 (LSCO), a representative HTS cuprate. In the past two decades, we have synthesized over three thousand LSCO thin films and characterized them by a range of analytical techniques. Here, we present in full detail a systematic process for the synthesis and engineering of atomically perfect LSCO films. The procedure includes the preparation of substrates, calibration of the elemental sources, the recipe for ALL growth of LSCO films without any secondary-phase precipitates, post-growth annealing of the films, and ex situ film characterization. This report should aid replication and dissemination of this technique of synthesizing single-crystal LSCO films for basic research as well as for HTS electronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

A Novel Active Optimization Approach for Rapid and Efficient Design Space Exploration Using Ensemble Machine Learning

In this work, a novel design optimization technique based on active learning, which involves dynamic exploration and exploitation of the design space of interest using an ensemble of machine learning algorithms, is presented. In this approach, a hybrid methodology incorporating an explorative weak learner (regularized basis function model) that fits high-level information about the response surface and an exploitative strong learner (based on committee machine) that fits finer details around promising regions identified by the weak learner is employed. For each design iteration, an aristocratic approach is used to select a set of nominees, where points that meet a threshold merit value as predicted by the weak learner are selected for evaluation. In addition to these points, the global optimum as predicted by the strong learner is also evaluated to enable rapid convergence to the actual global optimum once the most promising region has been identified by the optimizer. Additionally, this methodology is first tested by applying it to the optimization of a two-dimensional multi-modal surface and, subsequently, to a complex internal combustion (IC) engine combustion optimization case with nine control parameters related to fuel injection, initial thermodynamic conditions, and in-cylinder flow. It is found that the new approach significantly lowers the number of function evaluations that are needed to reach the optimum design configuration (by up to 80%) when compared to conventional optimization techniques, such as particle swarm and genetic algorithm-based optimization techniques.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Reliability of Copper Inverse Opal Surfaces for Extreme-Heat-Flux Micro-Coolers in Low-Global-Warming-Potential Refrigerant R-1233zd Pool Boiling Experiments

This presentation provides a brief snapshot of the InterPACK paper InterPACK2023-113781. The paper explores copper inverse opal (CIO) surface reliability in pool boiling experiments in water and a new, low-global-warming-potential (GWP = 1) hydrofluoroolefin (HFO) refrigerant R-1233zd. The CIO-based structure is intended to develop enhanced two-phase heat transfer surfaces for extreme-heat-flux (approximately 1 kW/cm2) micro-coolers. In this study, a limited number of pool boiling experiments were performed using water and HFO-1233zd fluid, and the reliability of the CIO-based surfaces was evaluated. Critical heat flux (CHF) values in HFO-1233zd at 40 Degrees Celsius to 45 Degrees Celsius saturation temperatures and the corresponding saturation pressures were also measured. The CHF values with the refrigerant are significantly lower compared to those with water, but the refrigerant allows for a wider usable temperature range in the end application of the micro-coolers and is not limited to data centers with controlled ambient conditions. Reliability experiments with CIO surface samples - involving pool boiling with water on the CIO surfaces for approximately 48 hours and with HFO-1233zd for 144 hours - showed no structural degradation of the enhanced surface or any significant performance drop in heat transfer coefficients. The CIO surface samples in water were oxidized, most likely due to the presence of air in water and in the experimental vessel.

critical heat flux↗
DOE OSTI2025

Uniform Field Electrode Generator

SAND2025-03788O Uniform Field Electrode Generator is a user-friendly tool designed to create uniform electric field electrodes, essential for high voltage applications. By generating electrodes with precise dimensions, it ensures a consistent electric field across their surfaces. This software is particularly beneficial for researchers and engineers working on projects like closing switches and studying power flow in advanced systems, such as the Z machine. Its unique approach simplifies the design process, making it accessible for users without technical expertise, while enhancing the efficiency and effectiveness of their electrical applications. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Mason, Tyler [Sandia National Lab. (SNL-CA), Liver↗
DOE OSTI2022

Experiments and modelling of adhesive failure initiation of an epoxy underfill: a study of electronic packaging survivability

Epoxy underfills can be implemented in electronic packaging to enhance solder joint reliability of surface mounted components. However, it is important for an engineer to have a failure criterion that can be used for failure predictions and redesign of electronic assemblies. For this study, data from epoxy bond failure in mock electronic part assemblies were correlated to finite element analyses to predict adhesive failure initiation. Experiments were performed to determine failure loads for various loading locations and nonlinear viscoelastic analyses were performed for the same loading locations to determine a maximum principal strain failure parameter. Predictions showed that a maximum principal strain failure parameter defined from one test could be used as an indicator of adhesive failure of an epoxy bond undergoing other modes of loading. Failure initiation predictions matched experimental data using a maximum principal strain failure parameter for an epoxy bond undergoing mixed modes of loading for both unfilled and alumina oxide filled 828DEA epoxy. Such experimental setup is deemed appropriate for future epoxy testing.

42 ENGINEERING↗
DOE OSTI2024

New Matrix Framework to Determine Carbon Storage Technical Viability

Carbon storage is an integral component of reducing CO2 emissions. Research over the past two decades has developed workflows for volume assessments and economic project feasibility, providing necessary and useful tools to progress geologic carbon storage (GCS) projects. These workflows and assessments have focused primarily on determining the in-situ storage resource based on geologic and engineering parameters and do not integrate subsurface characterization with surface conditions, social factors, and environmental factors that may pose a benefit or impediment to the implementation of GCS. Furthermore, the data required to assess the technical viability of GCS are myriad and disparate. There is no current methodology that identifies technical viability criteria and systematically informs how to aggregate these factors for spatial assessments. To address this gap, the National Energy Technology Laboratory has developed a Carbon Storage Technical Viability Approach (CS TVA) Matrix that incorporates a wide variety of factors to inform and accelerate screening for GCS site selection in the United States.

Mulhern, Julia↗
DOE OSTI2024

Methods of controllable interstitial oxygen doping in niobium

A method for vacuum heat treating Nb, such as is used in superconducting radio frequency cavities, to engineer the interstitial oxygen profile with depth into the surface to conveniently optimize the low-temperature rf surface resistance of the material. An example application is heating of 1.3 GHz accelerating structures between 250-400° C. to achieve a very high quality factor of 5×1010 at 2.0 K. With data supplied by secondary ion mass spectrometry measurements, application of oxide decomposition and oxygen diffusion theory was applied to quantify previously unknown parameters crucial in achieving the oxygen alloy concentration profiles required to optimize the rf surface resistance. RF measurements of vacuum heat treated Nb superconducting radio frequency cavities confirmed the minimized surface resistance (higher Q0) previously expected only from 800° C. diffusive alloying with nitrogen.

Palczewski, Ari D.↗
DOE OSTI2024

Mitigation of safety and environmental challenges posed by refrigerants

The abatement of safety and environmental burden associated with low and ultra-low Global Warming Potential (GWP) refrigerants is a critical undertaking. As the industry shifts towards more environmentally friendly alternatives, mitigating the potential risks and ensuring safety standards becomes paramount. The adoption of mildly and highly flammable refrigerants contributes significantly to minimizing the greenhouse gas impact on the environment, aligning with global climate and sustainability goals. However, it is essential to address safety concerns and potential environmental implications associated with the end use of these refrigerants. A method to mitigate the safety risk in a flammable refrigerant based heating, ventilation, air-conditioning, and refrigeration (HVACR) system is the primary focus of this paper. Advent of A2L and A3 refrigerants as replacements to high GWP refrigerants requires careful handling of leak episodes to lower or eliminate the risk associated with creating flammable mixtures capable of fire/explosion hazard. Solid materials tailored to target the molecule of interest (i.e., refrigerant.) by engineering the microporous structure as well as chemically functionalizing the surface to attract and hold on to the chemical compound being removed from the gas stream was realized. Quantitative analysis reveals the adsorbent's effectiveness in reducing leak potential in the range of 40 %–100 % for various refrigerants. Strategic placement and active leak management with negative pressure offer promising avenues for capturing leaked refrigerants, enhancing overall safety.

42 ENGINEERING↗