Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solution assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

On the apparent insignificance of the randomness of flexible joints on large space truss dynamics

Deployable periodic large space structures have been shown to exhibit high dynamic sensitivity to period-breaking imperfections and uncertainties. These can be brought on by manufacturing or assembly errors, structural imperfections, as well as nonlinear and/or nonconservative joint behavior. In addition, the necessity of precise pointing and position capability can require the consideration of these usually negligible and unknown parametric uncertainties and their effect on the overall dynamic response of large space structures. This work describes the use of a new design approach for the global dynamic solution of beam-like periodic space structures possessing parametric uncertainties. Specifically, the effect of random flexible joints on the free vibrations of simply-supported periodic large space trusses is considered. The formulation is a hybrid approach in terms of an extended Timoshenko beam continuum model, Monte Carlo simulation scheme, and first-order perturbation methods. The mean and mean-square response statistics for a variety of free random vibration problems are derived for various input random joint stiffness probability distributions. The results of this effort show that, although joint flexibility has a substantial effect on the modal dynamic response of periodic large space trusses, the effect of any reasonable uncertainty or randomness associated with these joint flexibilities is insignificant.

Koch, R. M.↗
NASA NTRS2000

Design and Flight Testing of an Inflatable Sunshield for the NGST

The Next Generation Space Telescope (NGST) mission is scheduled to launch in 2007 and be stationed at L2 for a mission life of ten years. The large aperture mirror and optical detectors aboard NGST require shielding from the constant solar energy seen at this orbit. The government reference NGST design, called the Yardstick, baselined a sunshield using an inflation deployment system. During the formulation phase, NGST is spending approximately 25% of the overall budget to foster the development of new technology. The goal is to develop and demonstrate enabling or enhancing technology and provide innovative solutions for the design of the NGST observatory. Inflatable technology falls in the category of enhancing technology due to its advantages in weight, stowed volume and cost. The Inflatable Sunshield in Space (ISIS) flight experiment will provide a realistic space flight demonstration of an inflatable sunshield. The supporting technology development program will provide an information base for the design, manufacture, assembly and testing of large thin membranes and inflatable structural elements for space structures. The ISIS experiment will demonstrate the feasibility of using inflatable technology to passively cool optical systems for NGST and provide correlation between analytical predictions and on orbit results. The experiment will be performed on a Hitchhiker/Space Shuttle mission in late 2001. The ISIS mission is an effort to address several major technical challenges of the NGST inflatable sunshield, namely controlled inflation deployment, plenarity and separation of large stretched membranes, space rigidization of inflatable booms, and dynamic modeling and simulation. This paper will describe the design of the flight experiment and the testing to be performed on-orbit.

Adams, Michael L.↗
NASA NTRS2013

Method for making a microporous membrane

A method for making a microporous membrane comprises the steps of: providing a plurality of carbon nanotubes having a hollow interior diameter of 20 Angstroms or less; sonicating the plurality of carbon nanotubes utilizing a solution comprising deionized, distilled water and a surfactant that coats at least one of the plurality of carbon nanotubes; collecting the coated carbon nanotubes; forming a matrix that supports the plurality of carbon nanotubes; embedding the coated carbon nanotubes into the matrix; rinsing the coated nanotubes to remove at least a portion of the surfactant; curing the nanotube-matrix assembly; and cutting the nanotube-matrix assembly to a particular thickness so as to open the ends of the embedded nanotubes. The hollow interiors of the plurality of embedded carbon nanotubes comprise the pores of the microporous membrane.

Gavalas, Lillian Susan↗
NASA NTRS2017

Work Term Assignment Spring 2017

My tour in the Engineering Robotics directorate exceeded my expectations. I learned lessons about Creo, manufacturing and assembly, collaboration, and troubleshooting. During my first tour, last spring, I used Creo on a smaller project, but had limited experience with it before starting in the Dynamic Systems Test branch this spring. I gained valuable experience learning assembly design, sheet metal design and designing with intent for manufacturing and assembly. These skills came from working both on the hatch and the floor. I also learned to understand the intent of other designers on models I worked with. While redesigning the floor, I was modifying an existing part and worked to understand what the previous designer had done to make it fit with the new model. Through working with the machine shop and in the mock-up, I learned much more about manufacturing and assembly. I used a Dremel, rivet gun, belt sander, and countersink for the first time. Through taking multiple safety training for different machine shops, I learned new machine shop safety skills specific to each one. This semester also gave me new collaborative opportunities. I collaborated with engineers within my branch as well as with Human Factors and the building 10 machine shop. This experience helped me learn how to design for functionality and assembly, not only for what would be easiest in my designs. In addition to these experiences, I learned many lessons in troubleshooting. I was the first person in my office to use a Windows 10 computer. This caused unexpected issues with NASA services and programs, such as the Digital Data Management Server (DDMS). Because of this, I gained experience finding solutions to lockout and freeze issues as well as Creo specific settings. These will be useful skills to have in the future and will be implemented in future rotations. This co-op tour has motivated me more to finish my degree and pursue my academic goals. I intend to take a machining Career Gateway Elective in the Fall to improve my skills in building as well as designing with manufacturing intent. I am also inspired to take more mechatronics CGE courses before I graduate to learn more about the crossover between mechanical and electrical engineering. This semester, I worked on multiple projects and had the opportunity to learn from engineers of different disciplines. I became proficient in Creo 2.0, a program I had not used significantly before. I finished modifying the hatch for 3D print and made sizeable modifications to the nose floor support design. I also gained hands-on experience that will be useful in my engineering career in the future. I would consider all of these major achievements from this spring semester. Lastly, I learned to ask more questions and to search for the right people to find answers which I know will be a valuable skill in the future. This summer, I will be completing my last rotation in the Flight Operations Directorate at Ellington Air Field. After this last tour, I will be returning to school for the Fall, Spring and Summer. I will graduate in August of 2018. I am looking forward to learning more about the different jobs available to engineers. This division works directly with many different types of aircrafts and I am excited to learn more about this focus of engineering. The Aircraft Operations Division values team work greatly and I intend to improve my interpersonal skills by working with them this summer.

Sico, Mallory↗
NASA NTRS2018

SpiderFab: Process for On-Orbit Construction of Kilometer-Scale Apertures

The SpiderFab effort has investigated the value proposition and feasibility of radically changing the way we build and deploy spacecraft by enabling space systems to fabricate and integrate key components on-orbit. In this Phase II effort, we have focused on developing and demonstrating tools and processes to enable robotic systems to manufacture and assemble high performance structural elements that will serve as the support structures for components such as antennas and solar arrays. Through testing of these technologies in the laboratory environment,these efforts have established the technical feasibility of the key capabilities required for in-space manufacture of large apertures such as antennas, solar arrays, and optical systems,maturing prototype technical solutions for these capabilities to TRL-4. The SpiderFab effort has resulted in successful post-NIAC transition of the technology, first to SBIR-funded development of a technology for in-space manufacture (ISM) of truss structures, and then to a NASA/STMD Tipping Point Technologies funded effort to prepare a flight demonstration of ISM of a structure for a GEO communications satellite.

Manufacturing↗
NASA NTRS1992

Assembly induced delaminations in composite structures

Experimental and analytical studies of the development of delaminations around fastener holes in composite structures are presented. This type of delamination is known to occur in composite skins that are mechanically fastened to a poorly mating substructure. Results of an experimental study to determine the resistance of laminates to the initiation of assembly induced delaminations and the residual strength of assembly damaged coupons are presented for AS4/3501-6, IM7/8551-7A, and AS4/PEEK material systems. A survey of existing analytical models for predicting the residual strength and stability of delaminations is presented, and the development of a new model for predicting the initiation of delaminations around a fastener hole is outlined. The fastener hole damage initiation model utilizes a finite element based Fourier series solution, and is validated through comparisons of analytical and experimental results.

Goering, J.↗
NASA NTRS2016

Essential SpaceWire Hardware Capabilities for a Robust Network

The Geostationary Operational Environmental Satellite R-Series Program (GOES-R) mission is a joint program between National Oceanic & Atmospheric Administration (NOAA) and National Aeronautics & Space Administration (NASA) Goddard Space Flight Center (GSFC). GOES-R project selected SpaceWire as the best solution to satisfy the desire for simple and flexible instrument to spacecraft command and telemetry communications. GOES-R development and integration is complete and the observatory is scheduled for launch October 2016. The spacecraft design was required to support redundant SpaceWire links for each instrument side, as well as to route the fewest number of connections through a Slip Ring Assembly necessary to support Solar pointing instruments. The final design utilized two different router designs. The SpaceWire standard alone does not ensure the most practical or reliable network. On GOES-R a few key hardware capabilities were identified that merit serious consideration for future designs. Primarily these capabilities address persistent port stalls and the prevention of receive buffer overflows. Workarounds were necessary to overcome shortcomings that could be avoided in future designs if they utilize the capabilities, discussed in this paper, above and beyond the requirements of the SpaceWire standard.

SpaceWire↗
NASA NTRS1980

Phase 2 of the array automated assembly task for the low cost silicon solar array project

Studies were conducted on several fundamental aspects of electroless nickel/solder metallization for silicon solar cells. A process, which precedes the electroless nickel plating with several steps of palladium plating and heat treatment, was compared directly with single step electroless nickel plating. Work was directed toward answering specific questions concerning the effect of silicon surface oxide on nickel plating, effects of thermal stresses on the metallization, sintering of nickel plated on silicon, and effects of exposure to the plating solution on solar cell characteristics. The process was found to be extremely lengthy and cumbersome, and was also found to produce a product virtually identical to that produced by single step electroless nickel plating, as shown by adhesion tests and electrical characteristics of cells under illumination.

Petersen, R. C.↗
NASA NTRS1995

Parallel Processing with Digital Signal Processing Hardware and Software

The assembling and testing of a parallel processing system is described which will allow a user to move a Digital Signal Processing (DSP) application from the design stage to the execution/analysis stage through the use of several software tools and hardware devices. The system will be used to demonstrate the feasibility of the Algorithm To Architecture Mapping Model (ATAMM) dataflow paradigm for static multiprocessor solutions of DSP applications. The individual components comprising the system are described followed by the installation procedure, research topics, and initial program development.

Swenson, Cory V.↗
NASA NTRS2002

Air Purification in Closed Environments: An Overview of Spacecraft Systems

The primary goal for a collective protection system and a spacecraft environmental control and life support system (ECLSS) are strikingly similar. Essentially both function to provide the occupants of a building or vehicle with a safe, habitable environment. The collective protection system shields military and civilian personnel from short-term exposure to external threats presented by toxic agents and industrial chemicals while an ECLSS sustains astronauts for extended periods within the hostile environment of space. Both have air quality control similarities with various aircraft and 'tight' buildings. This paper reviews basic similarities between air purification system requirements for collective protection and an ECLSS that define surprisingly common technological challenges and solutions. Systems developed for air revitalization on board spacecraft are discussed along with some history on their early development as well as a view of future needs. Emphasis is placed upon two systems implemented by the National Aeronautics and Space Administration (NASA) onboard the International Space Station (ISS): the trace contaminant control system (TCCS) and the molecular sieve-based carbon dioxide removal assembly (CDRA). Over its history, the NASA has developed and implemented many life support systems for astronauts. As the duration, complexity, and crew size of manned missions increased from minutes or hours for a single astronaut during Project Mercury to days and ultimately months for crews of 3 or more during the Apollo, Skylab, Shuttle, and ISS programs, these systems have become more sophisticated. Systems aboard spacecraft such as the ISS have been designed to provide long-term environmental control and life support. Challenges facing the NASA's efforts include minimizing mass, volume, and power for such systems, while maximizing their safety, reliability, and performance. This paper will highlight similarities and differences among air purification systems. Additional information is included in the original extended abstract.

Perry, Jay L.↗
NASA NTRS2003

Airloads and Wake Geometry Calculations for an Isolated Tiltrotor Model in a Wind Tunnel

Th tiltrotor aircraft configuration has the potential to revolutionize air transportation by providing an economical combination of vertical take-off and landing capability with efficient, high-speed cruise flight. To achieve this potential it is necessary to have validated analytical tools that will support future tiltrotor aircraft development. These analytical tools must calculate tiltrotor aeromechanical behavior, including performance, structural loads, vibration, and aeroelastic stability, with an accuracy established by correlation with measured tiltrotor data. For many years such correlation has been performed for helicopter rotors (rotors designed for edgewise flight), but correlation activities for tiltrotors have been limited, in part by the absence of appropriate measured data. The recent test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, U4-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) now provides an extensive set of aeroacoustic, performance, and structural loads data. This paper will present calculations of airloads, wake geometry, and performance, including correlation with TRAM DNW measurements. The calculations were obtained using CAMRAD II, which is a modern rotorcraft comprehensive analysis, with advanced models intended for application to tiltrotor aircraft as well as helicopters. Comprehensive analyses have received extensive correlation with performance and loads measurements on helicopter rotors. The proposed paper is part of an initial effort to perform an equally extensive correlation with tiltrotor data. The correlation will establish the level of predictive capability achievable with current technology; identify the limitations of the current aerodynamic, wake, and structural models of tiltrotors; and lead to recommendations for research to extend tiltrotor aeromechanics analysis capability. The purpose of the Tilt Rotor Aeroacoustic Model (TRAM) experimental project is to provide data necessary to validate tiltrotor performance and aeroacoustic prediction methodologies and to investigate and demonstrate advanced civil tiltrotor technologies. The TRAM project is a key part of the NASA Short Haul Civil Tiltrotor (SHCT) project. The SHCT project is an element of the Aviation Systems Capacity Initiative within NASA. In April-May 1998 the TRAM was tested in the isolated rotor configuration at the Large Low-speed Facility of the German-Dutch Wind Tunnels (DNW). A preparatory test was conducted in December 1997. These tests were the first comprehensive aeroacoustic test for a tiltrotor, including not only noise and performance data, but airload and wake measurements as well. The TRAM can also be tested in a fill-span configuration, incorporating both rotors Lnd a fuselage model. The wind tunnel installation of the TRAM isolated rotor is shown. The rotor tested in the DNW was a 1/4-scale (9.5 ft diameter) model of the right-hand V-22 proprotor. The rotor and nacelle assembly was attached to an acoustically-treated, isolated rotor test stand through a mechanical pivot (the nacelle conversion axis). The TRAM was analyzed using the rotorcraft comprehensive analysis CAMRAD II. CAMRAD II is an aeromechanical analysis of helicopters and rotorcraft that incorporates a combination of advanced technologies, including multibody dynamics, nonlinear finite elements, and rotorcraft aerodynamics. The trim task finds the equilibrium solution (constant or periodic) for a steady state operating condition, in this case a rotor operating in a wind tunnel. For wind tunnel operation, the thrust and flapping are trimmed to target values. The aerodynamic model includes a wake analysis to calculate the rotor nonuniform induced-velocities, using a free wake geometry. The paper will present the results of CAMRAD II calculations compared to the TRAM DNW measurements for hover performance, helicopter mode performance, and helicopter mode airloads. An example of the hover performance results, comparing both mearements and calculations for the JVX (large scale) and TRAM (small scale) rotors, is shown. An example of the helicopter mode performance, showing the influence of the aerodynamic model (particularly the stall delay model) on the calculated power, induced power, and profile power is also shown. An example of the helicopter mode airloads, showing the influence of various wake and aerodynamic models on the calculations, is shown. Good correlation with measured airloads is obtained using the multiple-trailer wake model. The paper will present additional results, and describe and discuss the aerodynamic behavior in detail.

Johnson, Wayne↗
NASA NTRS2005

International Space Station Carbon Dioxide Removal Assembly (ISS CDRA) Concepts and Advancements

An important aspect of air revitalization for life support in spacecraft is the removal of carbon dioxide from cabin air. Several types of carbon dioxide removal systems are in use in spacecraft life support. These systems rely on various removal techniques that employ different architectures and media for scrubbing CO2, such as permeable membranes, liquid amine, adsorbents, and absorbents. Sorbent systems have been used since the first manned missions. The current state of key technology is the existing International Space Station (ISS) Carbon Dioxide Removal Assembly (CDRA), a system that selectively removes carbon dioxide from the cabin atmosphere. The CDRA system was launched aboard UF-2 in February 2001 and resides in the U.S. Destiny Laboratory module. During the past four years, the CDRA system has operated with varying degrees of success. There have been several approaches to troubleshooting the CDRA system aimed at developing work-around solutions that would minimize the impact on astronaut time required to implement interim solutions. The paper discusses some of the short-term fixes applied to promote hardware life and restore functionality, as well as long-term plans and solutions for improving operability and reliability. The CDRA is a critical piece of life support equipment in the air revitalization system of the ISS, and is demonstrated technology that may ultimately prove well-suited for use in lunar or Mars base, and Mars transit life support applications.

ElSherif, Dina↗
NASA NTRS2006

Selective Plasma Deposition of Fluorocarbon Films on SAMs

A dry plasma process has been demonstrated to be useful for the selective modification of self-assembled monolayers (SAMs) of alkanethiolates. These SAMs are used, during the fabrication of semiconductor electronic devices, as etch masks on gold layers that are destined to be patterned and incorporated into the devices. The selective modification involves the formation of fluorocarbon films that render the SAMs more effective in protecting the masked areas of the gold against etching by a potassium iodide (KI) solution. This modification can be utilized, not only in the fabrication of single electronic devices but also in the fabrication of integrated circuits, microelectromechanical systems, and circuit boards. In the steps that precede the dry plasma process, a silicon mold in the desired pattern is fabricated by standard photolithographic techniques. A stamp is then made by casting polydimethylsiloxane (commonly known as silicone rubber) in the mold. The stamp is coated with an alkanethiol solution, then the stamp is pressed on the gold layer of a device to be fabricated in order to deposit the alkanethiol to form an alkanethiolate SAM in the desired pattern (see figure). Next, the workpiece is exposed to a radio-frequency plasma generated from a mixture of CF4 and H2 gases. After this plasma treatment, the SAM is found to be modified, while the exposed areas of gold remain unchanged. This dry plasma process offers the potential for forming masks superior to those formed in a prior wet etching process. Among the advantages over the wet etching process are greater selectivity, fewer pin holes in the masks, and less nonuniformity of the masks. The fluorocarbon films formed in this way may also be useful as intermediate layers for subsequent fabrication steps and as dielectric layers to be incorporated into finished products.

Crain, Mark M., III↗
NASA NTRSDate not supplied

Connecting Federal Agencies to Satellite Earth Observations: NASA’s Satellite Needs Working Group Assessment Process

The Satellite Needs Working Group (SNWG), part of the U.S. Group on Earth Observations (USGEO), surveys agencies across the U.S. Government to identify the satellite Earth observations each agency needs to fulfill its high-priority objectives and responsibilities. Around 20 civilian agencies participate in the SNWG survey every two years. After receiving the surveys, the National Aeronautics and Space Administration (NASA) conducts an in-depth evaluation of each agency's needs in collaboration with fellow satellite Earth data providers, the National Oceanic and Atmospheric Administration (NOAA) and the U.S. Geological Survey (USGS). This assessment process, which takes place over an eight-month period, is divided into distinct phases. NASA first assembles an assessment team with the necessary subject matter expertise to evaluate each submitted need. An in-depth interview with each submitting agency then follows, featuring discussion of current and upcoming satellite missions as well as potential new activities that NASA, NOAA, and/or USGS could undertake to meet the agency's needs. The assessment teams then further evaluate these potential activities or solutions to identify how many agencies would benefit and estimate how much their level of satisfaction would increase. Solutions expected to have broad-reaching and significant agency benefits are proposed by NASA for funding. SNWG agencies receive an assessment report for each submitted need, in which the tri-agency assessment teams provide a detailed evaluation of the agency need, information on relevant satellite missions, and links to specific datasets or training resources. The SNWG Management Office at NASA’s Interagency Implementation and Advanced Concepts Team (IMPACT) contributes to NASA’s SNWG assessment in a variety of capacities, including statistical analysis of the survey responses to identify trends and similar needs across multiple agencies. The Management Office also provides analytics for the new proposed solutions, demonstrating and quantifying their potential value. For activities that receive funding, the Management Office manages the implementation process and works to maximize the benefit to SNWG agencies via a Stakeholder Engagement Program.

Katrina Virts↗
NASA NTRSDate not supplied

Thermoplastic Space Point Design (TSPD) Tall Tower Lunar Thermal Analysis

The Thermoplastics Development for Exploration Applications (TDEA) project seeks to advance NASA’s thermoplastic composites capabilities by developing structurally efficient joining solutions for large-scale space structures to support NASA’s future exploration missions. A key objective is to develop and understand advanced thermoplastic joining techniques relevant to space environments and applicable to unitized and/or reconfigurable composite structures. The TDEA project uses NASA Langley’s Tall Lunar Tower (TLT) concept as a target application for the design and development of in-space assembled thermoplastic composites. TLT is a 50-meter-tall tower constructed on the lunar surface near the south pole. The tower’s height at this location on the moon allows for extended durations of incident solar flux which can be used to generate power via photovoltaic arrays. The thermal environment present on lunar south pole represents a challenging environment for any space-based asset. This study provides an overview of the analysis techniques used to determine the temperature extremes, gradients, and timelines of a tall composite tower over a one-year duration at the Shackleton Connecting Ridge. The developed thermal model includes tower and lunar surface elements with anisotropic and temperature-dependent material properties and incorporates a solar vector orbit with time-varying solar flux. Study topics include: a comparison between the effects of simplified lunar surface topologies on thermal results, prediction of surface temperature values versus Lunar Reconnaissance Orbiter (LRO) flight data, and tower structural-thermal deformation.

Lunar↗
NASA NTRS2020

Technology Advancements for Channel Wall Nozzle Manufacturing In Liquid Rocket Engines

A regeneratively-cooled or dump-cooled nozzle is a critical component for expansion of hot gases to enable high temperature and performance in liquid rocket engines systems. Regeneratively-cooled channel wall nozzles are a design solution used across the propulsion industry as a simplified method to fabricate the nozzle structure with internal coolant passages. The scale and complexity of the channel wall nozzle (CWN) design can be challenging to fabricate which results in extended lead times and higher costs. Some of these challenges include: 1) Unique and high temperature materials, 2) Tight tolerances on large parts during manufacturing and assembly to contain high pressure propellants, 3) Thin-walled features to maintain adequate wall temperatures, and 4) Unique manufacturing process operations and complex tooling. The United States (U.S.) National Aeronautics and Space Administration (NASA) and U.S. specialty manufacturing vendors are maturing modern fabrication techniques to reduce complexity and decrease costs associated with channel wall nozzle manufacturing technology. Additive Manufacturing (AM) is one of the key technology advancements under evaluation for channel wall nozzles. Much of additive manufacturing for propulsion components has focused on laser powder bed fusion (L-PBF), but the scale is not yet feasible for application to large scale nozzles. NASA is evolving directed energy deposition (DED) techniques for nozzles including arc-based deposition, blown powder deposition, and Laser Wire Direct Closeout (LWDC). There are different approaches being considered for fabrication of the nozzle, and each of these DED processes offer unique process steps for rapid fabrication. The arc-based and blown powder deposition techniques are used for the forming of the CWN liner. A variety of materials are being demonstrated including Inconel 625, Haynes 230, JBK-75, and NASA HR-1. The blown powder DED process is also being demonstrated for forming an integral channel nozzle in a single operation in similar materials. The LWDC process is a method for closing out the channels within the liner and forming the structural jacket using a localized laser wire deposition technique. Identical materials mentioned above have been used for this process in addition to bimetallic closeout (C-18150–SS347, and C-18150–Inconel 625). NASA has completed process development, material characterization, and hot-fire testing on a variety of these channel wall nozzle fabrication technique. This publication presents an overview of the various channel wall nozzle manufacturing processes and materials under evaluation including results from the hot-fire testing. Future development and technology focus areas is also discussed relative to channel wall nozzle manufacturing.

Additive manufacturing↗
NASA NTRS1972

IBM system/360 assembly language interval arithmetic software

Computer software designed to perform interval arithmetic is described. An interval is defined as the set of all real numbers between two given numbers including or excluding one or both endpoints. Interval arithmetic consists of the various elementary arithmetic operations defined on the set of all intervals, such as interval addition, subtraction, union, etc. One of the main applications of interval arithmetic is in the area of error analysis of computer calculations. For example, it has been used sucessfully to compute bounds on sounding errors in the solution of linear algebraic systems, error bounds in numerical solutions of ordinary differential equations, as well as integral equations and boundary value problems. The described software enables users to implement algorithms of the type described in references efficiently on the IBM 360 system.

Phillips, E. J.↗
NASA NTRS2004

Epoxy Adhesives for Stator Magnet Assembly in Stirling Radioisotope Generators (SRG)

As NASA seeks to fulfill its goals of exploration and understanding through missions planned to visit the moons of Saturn and beyond, a number of challenges arise from the idea of deep space flight. One of the first problems associated with deep space travel is electrical power production for systems on the spacecraft. Conventional methods such as solar power are not practical because efficiency decreases substantially as the craft moves away from the Sun. The criterion for power generation during deep space missions are very specific, the main points requiring high reliability, low mass, minimal vibration and a long lifespan. A Stirling generator, although fairly old in concept, is considered to be a potential solution for electrical power generation for deep space flight. A Stirling generator works on the same electromagnetic principles of a standard generator, using the linear motion of the alternator through the stationary stator which produces electric induction. The motion of the alternator, however, is produced by the heating and cooling dynamics of pressurized gases. Essentially heating one end and cooling another of a contained gas will cause a periodic expansion and compression of the gas from one side to the other, which a displacer translates into linear mechanical motion. NASA needs to confirm that the materials used in the generator will be able to withstand the rigors of space and the life expectancy of the mission. I am working on the verification of the epoxy adhesives used to bond magnets to the steel lamination stack to complete the stator; in terms of in-service performance and durability under various space environments. Understanding the proper curing conditions, high temperature properties, and degassing problems as well as production difficulties are crucial to the long term success of the generator. system and steel substrate used in the stator. To optimize the curing conditions of the epoxies, modulated differential scanning calorimetry analysis was done as a function of cure time and temperatures. Adhesion bond strength was tested at various temperatures with lap shear samples using Hiperco 50 substrate to ensure that the proper adhesive is being used. To try and solve the problem of bondline thickness, micro glass beads of 0.0017" in diameter were investigated to see if any other physical properties of the epoxy were affected. Efforts will be made to develop a standard, optimized, fabrication process/procedure of sub-scale magnet-stator assemblies for various adhesive performance evaluation studies under simulated generator conditions. Also, accelerated aging testing will be done in a pressurized canister with stator assembly samples for three years to verify if any degassing or thermal degradation of the epoxy occurs. The necessity of verifying the correct epoxy adhesive system for the stator magnet in the SRG is crucial because failure of the stator assembly would jeopardize the electrical system, and thereby the entire mission itself. My work involves specimen fabrications, testing, and data analyses of the epoxy adhesive system for the stator magnet in the SRG is crucial because failure of the stator assembly would jeopardize the electrical system, and thereby the entire mission itself.

Cater, George M.↗