SEARCH · Engineering Papers

Results for “reference models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Normalizing a Relativistic Model of X-Ray Reflection Definition of the Reflection Fraction and Its Implementation in relxill

Aims. The only relativistic reflection model that implements a parameter relating the intensity incident on an accretion disk to the observed intensity is relxill. The parameter used in earlier versions of this model, referred to as the reflection strength, is unsatisfactory; it has been superseded by a parameter that provides insight into the accretion geometry, namely the reflection fraction. The reflection fraction is defined as the ratio of the coronal intensity illuminating the disk to the coronal intensity that reaches the observer. Methods. The relxill model combines a general relativistic ray-tracing code and a photoionization code to compute the component of radiation reflected from an accretion that is illuminated by an external source. The reflection fraction is a particularly important parameter for relativistic models with well-defined geometry, such as the lamp post model, which is a focus of this paper. Results. Relativistic spectra are compared for three inclinations and for four values of the key parameter of the lamp post model,namely the height above the black hole of the illuminating, on-axis point source. In all cases, the strongest reflection is produced for low source heights and high spin. A low-spin black hole is shown to be incapable of producing enhanced relativistic reflection. Results for the relxill model are compared to those obtained with other models and a Monte Carlo simulation. Conclusions. Fitting data by using the relxill model and the recently implemented reflection fraction, the geometry of a system can be constrained. The reflection-fraction is independent of system parameters such as inclination and black hole spin. The reflection-fraction parameter was implemented with the name reflec_frac all flavours of the relxill model, and the non-relativistic reflection model xillver, in v0.4a (18 January 2016).

accretion↗

NASA NTRS1997

Object-Oriented Control System Design Using On-Line Training of Artificial Neural Networks

This report deals with the object-oriented model development of a neuro-controller design for permanent magnet (PM) dc motor drives. The system under study is described as a collection of interacting objects. Each object module describes the object behaviors, called methods. The characteristics of the object are included in its variables. The knowledge of the object exists within its variables, and the performance is determined by its methods. This structure maps well to the real world objects that comprise the system being modeled. A dynamic learning architecture that possesses the capabilities of simultaneous on-line identification and control is incorporated to enforce constraints on connections and control the dynamics of the motor. The control action is implemented "on-line", in "real time" in such a way that the predicted trajectory follows a specified reference model. A design example of controlling a PM dc motor drive on-line shows the effectiveness of the design tool. This will therefore be very useful in aerospace applications. It is expected to provide an innovative and noval software model for the rocket engine numerical simulator executive.

Rubaai, Ahmed↗

NASA NTRSDate not supplied

Feasibility Study of a Multi-Tilt-Rotor Aircraft as the Artemis Lunar Training Vehicle

The Lunar Landing Research Vehicles (LLRVs) and the Lunar Landing Training Vehicles (LLTVs) provided astronauts of the Apollo program with essential experience and confidence required to complete the missions, and contributed to six successful manned landings on the moon. The primary challenge in terrestrial training was being able to replicate the ratio of tilt angle to linear acceleration that a pilot would experience in lunar gravity. Presently, as the Artemis program seeks to return humans to the Moon by 2025, engineers are evaluating suitable platforms to serve as an In-Flight Trainer (IFT) or Artemis Lunar Training Vehicle (ALTV) for astronauts training in the task of manual landing. The program is investigating the viability of current technology in the field of electric vertical takeoff and landing (eVTOL) vehicles and is evaluating using a multi-tilt-rotor aircraft platform as a candidate for a preliminary ALTV. The tilt-rotor capability enables the vehicle attitude to be decoupled from its flight path, which is a crucial requirement in realistically simulating lunar gravity on Earth. Other key considerations include compensating for a lack of aerodynamic forces while flying through the atmosphere of Earth, as well as the ability to simulate the dynamics of multiple different lander designs for the Human Landing System (HLS) program. This paper details the feasibility study and presents a preliminary flight control architecture for an IFT based on a notional multi-tilt-rotor platform. The model-following control law, based on nonlinear dynamic inversion (NDI), removes the need for gain scheduling. The inner-loop dynamic control allocation strategy consists of a static portion that is optimized offline for trim while compensating for the difference in gravity and a dynamic portion that is computed in real time. The reference model consists of the full closed-loop dynamics of a generic HLS design. The modularity of the flight control architecture enables evaluation of multiple HLS concepts with minimal modifications to the control law. Simulation results of the multi-tilt-rotor configuration following the final portion of the Apollo 11 descent trajectory are shown.

Jing Pei↗

NASA NTRS1985

Application of adaptive control to space stations

The space station will be deployed and assembled in low earth orbit with multiple Shuttle trips. Several construction phases will be required involving both ground and in-orbit operations. In this paper, the construction process of a four-panel space station and its control problems are discussed. The applicability of a direct model reference adaptive control technique with plant augmentation is investigated. Control during several key assembly operation periods has been simulated. These include Shuttle docking with initial-phase station, habitat module mating, and Shuttle docking with operational station. High rate of convergence and robust performance have been observed for all the simulated cases even with 40 percent model parameter errors and model truncations and more than 100 percent instant mass property variations. Controller with severe gain saturations is also discussed and results show only slight performance deterioration.

Ih, C.-H. C.↗

NASA NTRS2003

Reference architecture for space data systems

This paper introduces the Reference Architecture for Space Data Systems (RASDS)that is being developed by CCSDS. RASDS uses five views to describe architectures of space data systems. These views are derived from the viewpoints of the Reference Model of Open Distributed Processing (RM-ODP), but they are slightly modified from the RM-ODP viewpoints so that they can better represent the concerns of space data systems.

CCSDS space communication reference architecture s↗

NASA NTRS1987

Adaptive control of robotic manipulators

The author presents a novel approach to adaptive control of manipulators to achieve trajectory tracking by the joint angles. The central concept in this approach is the utilization of the manipulator inverse as a feedforward controller. The desired trajectory is applied as an input to the feedforward controller which behaves as the inverse of the manipulator at any operating point; the controller output is used as the driving torque for the manipulator. The controller gains are then updated by an adaptation algorithm derived from MRAC (model reference adaptive control) theory to cope with variations in the manipulator inverse due to changes of the operating point. An adaptive feedback controller and an auxiliary signal are also used to enhance closed-loop stability and to achieve faster adaptation. The proposed control scheme is computationally fast and does not require a priori knowledge of the complex dynamic model or the parameter values of the manipulator or the payload.

Seraji, H.↗

NASA NTRSDate not supplied

Feasibility Study of a Multi Tilt-rotor Aircraft as the Artemis Lunar Training Vehicle

The Lunar Landing Research Vehicles (LLRVs) and the Lunar Landing Training Vehicles (LLTVs) provided astronaut candidates for the Apollo program with essential experience and confidence required to complete the missions, and contributed to six successful manned landings on the moon. The primary challenge in terrestrial training was being able to replicate the ratio of bank angle to linear acceleration that a pilot would experience in lunar gravity. Presently, as the Artemis program seeks to return humans to the Moon by 2025, engineers are evaluating suitable platforms to serve as an In-Flight Trainer (IFT) or Artemis Lunar Training Vehicle (ALTV) for astronauts training in the task of manual landing. The program is investigating the viability of current technology in the field of electric vertical takeoff and landing (eVTOL) vehicles and is evaluating using a multi tilt-rotor aircraft platform as a candidate platform for a preliminary ALTV. The tilt-rotor capability enables the vehicle attitude to be decoupled from its flight path, which is a crucial requirement in realistically simulating lunar gravity on Earth. Other key considerations include compensating for a lack of aerodynamic forces while flying through the atmosphere of Earth, as well as the ability to simulate the dynamics of multiple different lander designs for the Human Landing System (HLS) program. This paper details the feasibility study and presents a preliminary flight control architecture for an IFT based on a notional multi tilt-rotor platform. The modeling-following control law, based on nonlinear dynamic inversion (NDI), removes the need for gain scheduling because the vehicle operates across a wide range of flight conditions. The inner-loop dynamic control allocation strategy consists of a static portion that is optimized offline for trim while compensating for the difference in gravity and a dynamic portion that is computed in real time. The reference model consists of the full closed-loop dynamics of a generic HLS design. The modularity of the flight control architecture enables evaluation of multiple HLS concepts with minimal modifications to the control law. Simulation results of the multi tilt-rotor configuration following the final portion of the Apollo 11 descent trajectory are shown.

Jing Pei↗

NASA NTRS1996

Long-term archiving and data access: modelling and standardization

This paper reports on the multiple difficulties inherent in the long-term archiving of digital data, and in particular on the different possible causes of definitive data loss. It defines the basic principles which must be respected when creating long-term archives. Such principles concern both the archival systems and the data. The archival systems should have two primary qualities: independence of architecture with respect to technological evolution, and generic-ness, i.e., the capability of ensuring identical service for heterogeneous data. These characteristics are implicit in the Reference Model for Archival Services, currently being designed within an ISO-CCSDS framework. A system prototype has been developed at the French Space Agency (CNES) in conformance with these principles, and its main characteristics will be discussed in this paper. Moreover, the data archived should be capable of abstract representation regardless of the technology used, and should, to the extent that it is possible, be organized, structured and described with the help of existing standards. The immediate advantage of standardization is illustrated by several concrete examples. Both the positive facets and the limitations of this approach are analyzed. The advantages of developing an object-oriented data model within this contxt are then examined.

Hoc, Claude↗

NASA NTRS1986

Design of adaptive control systems by means of self-adjusting transversal filters

The design of closed-loop adaptive control systems based on nonparametric identification was addressed. Implementation is by self-adjusting Least Mean Square (LMS) transversal filters. The design concept is Model Reference Adaptive Control (MRAC). Major issues are to preserve the linearity of the error equations of each LMS filter, and to prevent estimation bias that is due to process or measurement noise, thus providing necessary conditions for the convergence and stability of the control system. The controlled element is assumed to be asymptotically stable and minimum phase. Because of the nonparametric Finite Impulse Response (FIR) estimates provided by the LMS filters, a-priori information on the plant model is needed only in broad terms. Following a survey of control system configurations and filter design considerations, system implementation is shown here in Single Input Single Output (SISO) format which is readily extendable to multivariable forms. In extensive computer simulation studies the controlled element is represented by a second-order system with widely varying damping, natural frequency, and relative degree.

Merhav, S. J.↗

NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels. A reference model propeller (designated F31/A31), having aft-swept blades in both rotors, was also tested. Aeroelastic performance of the F39/A31 propeller was disappointing. The forward rotor tip region tended to untwist toward higher effective blade angles under load. The forward rotor also exhibited steady state blade flutter at speeds and loadings well below the design condition. The noise results, based on sideline acoustic data, show that the interaction tone levels were up to 8 dB higher with the forward-swept design compared to those for the reference propeller at similar operating conditions, with these tone level differences extending down to lower propeller speeds where flutter did not occur. These acoustic results are for a poorly-performing forward-swept propeller. It is quite possible that a properly-designed forward-swept propeller would exhibit substantial interaction tone level reductions.

Woodward, Richard P.↗

NASA NTRS2002

Application of Sliding Mode Methods to the Design of Reconfigurable Flight Control Systems

Observer-based sliding mode control is investigated for application to aircraft reconfigurable flight control. A comprehensive overview of reconfigurable flight control is given, including, a review of the current state-of-the-art within the subdisciplines of fault detection, parameter identification, adaptive control schemes, and dynamic control allocation. Of the adaptive control methods reviewed, sliding mode control (SMC) appears very promising due its property of invariance to matched uncertainty. An overview of sliding mode control is given and its remarkable properties are demonstrated by example. Sliding mode methods, however, are difficult to implement because unmodeled parasitic dynamics cause immediate and severe instability. This presents a challenge for all practical applications with limited bandwidth actuators. One method to deal with parasitic dynamics is the use of an asymptotic observer in the feedback path. Observer-based SMC is investigated, and a method for selecting observer gains is offered. An additional method for shaping the feedback loop using a filter is also developed. It is shown that this SMC prefilter is equivalent to a form of model reference hedging. A complete design procedure is given which takes advantage of the sliding mode boundary layer to recast the SMC as a linear control law. Frequency domain loop shaping is then used to design the sliding manifold. Finally, three aircraft applications are demonstrated. An F-18/HARV is used to demonstrate a SISO pitch rate tracking controller. It is also used to demonstrate a MIMO lateral-directional roll rate tracking controller. The last application is a full linear six degree-of-freedom advanced tailless fighter model. The observer-based SMC is seen to provide excellent tracking with superior robustness to parameter changes and actuator failures.

Wells, Scott R.↗

NASA NTRS1998

Modelling and Estimation of Dynamic Ocean Topography Within Global Geopotential Solutions

In this poster, we will present a report on the ongoing investigation "Improved Gravitational and Dynamic Height Models Through the use of Oceanographic Data." we have used a two year mean (1993-1994) of the Dynamic ocean Topography (DOT) field implied by the Semtner and Chervin POCM_4B model, and developed normal equations in surface spherical harmonics to degree and order 30. These normal equations, were combined with normal equations derived from TOPEX and ERS-1 altimeter data over the same time period. Combination solutions (based on satellite tracking data, altimeter data, surface gravity data and OCM data) were were developed Test solutions were obtained estimating the DOT field to 2Ox2O and 3ox3O. These solutions were tested with independent DOT values computed over 38 WOCE hydrographic sections, which contained a total of 3072 stations and represented 216000 km of travelled lines. The weighted standard deviation of the differences between the DOT obtained from the hydrographic data and and the field estimated from the joint combination solutions was computed for each of the test models, the weighted standard deviation for the baseline combination solution excluding the POCM4_B data was 9.7 cm for a DOT solution to 30x30, where introducing the POCM4_B data into the combination model reduced the standard deviation to 9.2 cm, indicating the the introduction of oceanographic information benefits the solution for the dynamic ocean topography. We will discuss the weighting schemes applied and the method of solution. Another aspect of our investigation involves testing alternate parametric representations of the dynamic height field. We looked at the alternative representations in terms of the Proudman functions (PF), and compared these to the use of spherical harmonics (SH) to represent the dynamic ocean topography, using once again the 1993 and 1994 output of the POCM4_B OCM as the reference model. A significant advantage of PF's over SH's is that the former require no "fill-in" values over areas where the DOT is undefined. We show that the PF and SH results using equal number of parameters agree quite well in overall content. In addition, PFs appear better suited for representation of high frequency signals close to the signal boundary. The development of the PF solutions for the DOT will be described and the statistics of the comparisons will be presented.

Lemoine, Frank G.↗

NASA NTRS2010

Optimal Control Modification Adaptive Law for Time-Scale Separated Systems

Recently a new optimal control modification has been introduced that can achieve robust adaptation with a large adaptive gain without incurring high-frequency oscillations as with the standard model-reference adaptive control. This modification is based on an optimal control formulation to minimize the L2 norm of the tracking error. The optimal control modification adaptive law results in a stable adaptation in the presence of a large adaptive gain. This study examines the optimal control modification adaptive law in the context of a system with a time scale separation resulting from a fast plant with a slow actuator. A singular perturbation analysis is performed to derive a modification to the adaptive law by transforming the original system into a reduced-order system in slow time. A model matching conditions in the transformed time coordinate results in an increase in the actuator command that effectively compensate for the slow actuator dynamics. Simulations demonstrate effectiveness of the method.

Nguyen, Nhan T.↗

NASA NTRS2009

Optimal Control Modification for Robust Adaptation of Singularly Perturbed Systems with Slow Actuators

Recently a new optimal control modification has been introduced that can achieve robust adaptation with a large adaptive gain without incurring high-frequency oscillations as with the standard model-reference adaptive control. This modification is based on an optimal control formulation to minimize the L2 norm of the tracking error. The optimal control modification adaptive law results in a stable adaptation in the presence of a large adaptive gain. This study examines the optimal control modification adaptive law in the context of a system with a time scale separation resulting from a fast plant with a slow actuator. A singular perturbation analysis is performed to derive a modification to the adaptive law by transforming the original system into a reduced-order system in slow time. The model matching conditions in the transformed time coordinate results in increase in the feedback gain and modification of the adaptive law.

Nguyen, Nhan T.↗

NASA NTRS2012

Optimal Control Modification for Time-Scale Separated Systems

Adaptive Control↗

NASA NTRS1993

Stability and instability of thermocapillary convection in models of the float-zone crystal-growth process

This project was concerned with the determination of conditions of guaranteed stability and instability for thermocapillary convection in a model of the float-zone crystal-growth process. This model, referred to as the half-zone, was studied extensively, both experimentally and theoretically. Our own earlier research determined, using energy-stability theory, sufficient conditions for stability to axisymmetric disturbances. Nearly all results computed were for the case of a liquid with Prandtl Number Pr = 1. Attempts to compute cases for higher Prandtl numbers to allow comparison with the experimental results of other researchers were unsuccessful, but indicated that the condition guaranteeing stability against axisymmetric disturbances would be a value of the Marangoni number (Ma), significantly higher than that at which oscillatory convection was observed experimentally. Thus, additional results were needed to round out the stability picture for this model problem. The research performed under this grant consisted of the following: (1) computation of energy-stability limits for non-axisymmetric disturbances; (2) computation of linear-stability limits for axisymmetric and non-axisymmetric disturbances; (3) numerical simulation of the basic state for half- and full-zones with a deformable free surface; and (4) incorporation of radiation heat transfer into a model energy-stability problem. Each of these is summarized briefly below.

Neitzel, G. P.↗

NASA NTRS2007

Observations on Cost Modeling and Performance Measurement of Long Term Archives

This paper describes a prototype suite of Excel-based tools that could be used for estimating lifecycle costs for newly planned or modified long-term archival facilities. These tools may also prove valuable for monitoring the long-term performance of such facilities once operational. Cost estimation is by analogy, using statistical curve-fitting techniques across a database of comparable data activities. The database currently includes 29 operational data centers ranging from small (2 FTEs) to large (66 FTEs), and is readily expandable to include additional activities specifically involving data preservation and added value. Each comparable data center is described in terms of its staffing, throughput workload, archival and distribution requirements, levels of user service, overall complexity, degree of automation, and other data, comprising 94 distinct descriptors in all. The descriptors were developed by normalizing heterogeneous data from the various centers and mapping them into an Excel framework consistent with the OAIS reference model. A user-friendly tool is provided for generating input to and updating the comparables database. This tool can also be used to benchmark the performance (in terms of cost versus throughput) of an operational data center, and to update the staffing, cost and workload data on a periodic basis. The comparables database could thus provide a history of staffing and throughput over time, as a means of performance monitoring and providing feedback for continuous improvement. Ancillary tools are also provided for performing "what-if' cost exercises for planning purposes, and for graphical display of data and results. We provide a high-level description of the tools; present our experiences and observations on gathering the information and maintaining the database; and discuss how this tool set might be applied to long term archives.

Fontaine, Kathy↗

NASA NTRS1991

Architecture for Survivable System Processing (ASSP)

The Architecture for Survivable System Processing (ASSP) Program is a multi-phase effort to implement Department of Defense (DOD) and commercially developed high-tech hardware, software, and architectures for reliable space avionics and ground based systems. System configuration options provide processing capabilities to address Time Dependent Processing (TDP), Object Dependent Processing (ODP), and Mission Dependent Processing (MDP) requirements through Open System Architecture (OSA) alternatives that allow for the enhancement, incorporation, and capitalization of a broad range of development assets. High technology developments in hardware, software, and networking models, address technology challenges of long processor life times, fault tolerance, reliability, throughput, memories, radiation hardening, size, weight, power (SWAP) and security. Hardware and software design, development, and implementation focus on the interconnectivity/interoperability of an open system architecture and is being developed to apply new technology into practical OSA components. To insure for widely acceptable architecture capable of interfacing with various commercial and military components, this program provides for regular interactions with standardization working groups (e.g.) the International Standards Organization (ISO), American National Standards Institute (ANSI), Society of Automotive Engineers (SAE), and Institute of Electrical and Electronic Engineers (IEEE). Selection of a viable open architecture is based on the widely accepted standards that implement the ISO/OSI Reference Model.

Wood, Richard J.↗