Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pumps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Diode laser-pumped solid-state lasers

An evaluation is made of the consequences for solid-state lasers of novel diode laser-pumping technology. Diode laser-pumped neodymium lasers have operated at an electrical-to-optical efficiency of 10 percent in a single spatial mode, with linewidths of less than 10 kHz, and with a spectral power brightness sufficiently great to allow frequency extension by harmonic generation in nonlinear crystals; this has yielded green and blue sources of coherent radiation. Q-switched operation with kW peak powers and mode-locked operation with 10-picosec pulse widths have also been demonstrated. All-solid-state lasers at prices comparable to those of current flash-lamp-pumped laser systems are foreseen, as are power levels exceeding 1 kW, for coherent radar, global satellite sensing, and micromachining.

Byer, Robert L.↗
NASA NTRS1987

Feasibility of solar-pumped dye lasers

Dye laser gains were measured at various pump-beam irradiances on a dye cell in order to evaluate the feasibility of solar pumping. Rhodamine 6G dye was considered as a candidate for the solar-pumped laser because of its high utilization of the solar spectrum and high quantum efficiency. Measurements show that a solar concentration of 20,000 is required to reach the threshold of the dye.

Lee, Ja H.↗
NASA NTRS1988

Generation of high-power nanosecond pulses from laser diode-pumped Nd:YAG lasers

Simulation results are used to compare the pulse energy levels and pulse energy widths that can be achieved with LD-pumped Nd:YAG lasers for both the pulse-transmission mode (PTM) and pulse-reflection mode (PRM) Q-switching methods for pulse energy levels up to hundreds of microjoules and pulse widths as short as 1 ns. It is shown that high-power pulses with pulse widths as short as 1 ns can be generated with PTM Q-switched in LD-pumped Nd:YAG lasers. With the PRM Q-switching method, pulse widths as short as 2 ns and pulse energy at the level of a few hundred microjoules can also be achieved but require pumping with 8-10-mJ AlGaAs laser diode arrays.

Chan, Kinpui↗
NASA NTRS1987

Unsteady diffuser vane pressure and impeller wake measurements in a centrifugal pump

Unsteady surface pressure measurements on a vaned diffuser of a centrifugal pump, and wake measurements of the flow exiting a centrifugal impeller into a vaneless diffuser are presented. Frequency spectra and ensemble averages are given for the unsteady measurements. Two different impellers were used, the pump impeller of the HPOTP (High Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine) and a two-dimensional impeller. The magnitude of the unsteady total pressure measured in the stationary frame at the impeller exit was found to be of the same order of magnitude as the total pressure rise across the pump. The magnitude of the unsteady diffuser vane pressures was observed to be significantly different on suction and pressure side of the vane, attaining its largest value on the suction side the leading edge while decreasing along the vane.

Arndt, N.↗
NASA NTRS1988

Diode laser-pumped solid-state lasers

Recently, interest in diode laser-pumped solid-state lasers has increased due to their advantages over flashlamp-pumped solid-state lasers. A historical overview is presented of semiconductor diode-pumped solid-state lasers beginning with work in the early 1960s and continuing through recent work on wavelength extension of these devices by laser operation on new transitions. Modeling of these devices by rate equations to obtain expressions for threshold, slope efficiency, and figures of merit is also given.

Fan, Tso Yee↗
NASA NTRS1988

Spectroscopy and diode laser-pumped operation of Tm, Ho:YAG

Spectroscopic measurements and analysis of diode laser-pumped operation of Tm, Ho:YAG at 2.1 microns at room temperature have been performed. The peak effective stimulated emission cross section is measured to be 9 x 10-21 sq cm at 2.091 microns and the upper state lifetime is 8.5 ms. Under diode laser pumping, thresholds of 4.4 mW of absorbed power and slope efficiency of 19 percent have been demonstrated. Calculations of threshold power are performed based on the spectroscopic measurements. An energy transfer upconversion process is identified which leads to a sublinear rise in upper-state population with pump power.

Fan, Tso Yee↗
NASA NTRS1988

Performance of a small centrifugal pump in He I and He II

The performance characteristics of a small centrifugal pump in He I and He II are determined over the temperature range of 1.6 to 4.2 K. The single-stage pump is powered by a close-coupled cryogenic induction motor. In the absence of cavitation, pump performance (head and capacity) was found to be identical for He I and He II. Developed heads up to 16 m and capacities of up to 900 liters/hr are obtained at 7000 rpm. A three-blade screw inducer was shown to require much less suction head than a six-blade propeller inducer.

Ludtke, P. R.↗
NASA NTRS1988

Pump performance requirement for the liquid helium orbital resupply tanker

The Liquid Helium Orbital Resupply Tanker (currently renamed to Superfluid Helium Tanker) will greatly enhance the lifetime of the space missions which require superfluid helium. The Superfluid Helium Tanker pump performance requirement is driven by the superfluid helium replenishment needs of the Space Infrared Telescope Facility (SIRTF). SIRTF is one of the space missions which will require on-orbit superfluid helium resupply in the 1990s. The Superfluid Helium Tanker will carry at least 10,000 L of superfluid helium and provide a minimum pump head of 170 torr (0 to 200 L/h) to cool SIRTF from 150 to 2 K. When the SIRTF tank starts to collect liquid, a minimum flow rate of 300 L/h with a pump head of 60 torr is required to fill the 4000-liter tank.

Lee, J. H.↗
NASA NTRS1989

Phase Separators And Fountain-Effect Pumps For He 11

Fused-glass microchannel arrays for use as HE 11 phase separators and fountain-effect pumps. Microchannel devices for use in low-gravity storage and cooling systems containing superfluid helium. Phase separators and pumps take advantage of thermomechanical effect peculiar to He 11 in restricted spaces. By creating thermal gradient in porous plug, direction of flow reversed, turning phase separator into pump. However, addition of heat disadvantage. Thermal gradient created by using Peltier effect to transfer heat across array, removing heat from He 11 supply and overcoming undesirable addition of heat.

Whitehouse, Paul L.↗
NASA NTRS1988

Studies of blackbody-pumped lasers

Laser action was achieved in a large-scale pulsed system and meaningful experiments were carried out in the axial flow facility to understand the physics of solar-pumped lasers. Studies of the variation of laser mixture composition were done for mixtures of CO2 and N2O additions. Theoretical analysis and modeling of the system were also performed based on a model including radiative pumping, diffusion and wall deactivation, and vibrational energy transfer between two optically active species. Qualitative agreement between predictions in the parameter variation and the experimental results were obtained with CO and N2O mixtures. Several experimental studies were performed to quantify the properties of carbon monoxide as absorber and storage of energy in the blackbody pumped system.

Christiansen, W. H.↗
NASA NTRS1988

Direct solar-pumped iodine laser amplifier

A XeCl laser which was developed earlier for an iodine laser oscillator was modified in order to increase the output pulse energy of XeCl laser so that the iodine laser output energy could be increased. The electrical circuit of the XeCl laser was changed from a simple capacitor discharge circuit of the XeCl laser to a Marx system. Because of this improvement the output energy from the XeCl laser was increased from 60 mj to 80 mj. Subsequently, iodine laser output energy was increased from 100 mj to 3 mj. On the other hand, the energy storage capability and amplification characteristics of the Vortek solar simulator-pumped amplifier was calculated expecting the calculated amplification factor is about 2 and the energy extraction efficiency is 26 percent due to the very low input energy density to the amplifier. As a result of an improved kinetic modeling for the iodine solar simulator pumped power amplifier, it is found that the I-2 along the axis of the tube affects seriously the gain profile. For the gas i-C3F7I at the higher pressures, the gain will decrease due to the I-2 as the pumping intensity increases, and at these higher pressures an increase in flow velocity will increase the gain.

Han, Kwang S.↗
NASA NTRS1989

Analysis of Nd3+:glass, solar-pumped, high-powr laser systems

The operating characteristics of Nd(3+):glass lasers energized by a solar concentrator were analyzed for the hosts YAG, silicate glass, and phosphate glass. The modeling is based on the slab zigzag laser geometry and assumes that chemical hardening methods for glass are successful in increasing glass hardness by a factor of 4. On this basis, it was found that a realistic 1-MW solar-pumped laser might be constructed from phosphate glass 4 sq m in area and 2 mm thick. If YAG were the host medium, a 1-MW solar-pumped laser need only be 0.5 sq m in area and 0.5 cm thick, which is already possible. In addition, Nd(3+) doped glass fibers were found to be excellent solar-pumped laser candidates. The small diameter of fibers eliminates thermal stress problems, and if their diameter is kept small (10 microns), they propagate a Gaussian single mode which can be expanded and transmitted long distances in space. Fiber lasers could then be used for communications in space or could be bundled and the individual beams summed or phase-matched for high-power operation.

Zapata, L. E.↗
NASA NTRS1989

Prototype laser-diode-pumped solid state laser transmitters

Monolithic, diode-pumped Nd:YAG ring lasers can provide diffraction-limited, single-frequency, narrow-linewidth, tunable output which is adequate for use as a local oscillator in a coherent communication system. A laser was built which had a linewidth of about 2 kHz, a power of 5 milliwatts, and which was tunable over a range of 30 MHz in a few microseconds. This laser was phase-locked to a second, similar laser. This demonstrates that the powerful technique of heterodyne detection is possible with a diode-pumped laser used as the local oscillator. Laser diode pumping of monolithic Nd:YAG rings can lead to output powers of hundreds of milliwatts from a single laser. A laser was built with a single-mode output of 310 mW. Several lasers can be chained together to sum their power, while maintaining diffraction-limited, single frequency operation. This technique was demonstrated with two lasers, with a total output of 340 mW, and is expected to be practical for up to about ten lasers. Thus with lasers of 310 mW, output of up to 3 W is possible. The chaining technique, if properly engineered, results in redundancy. The technique of resonant external modulation and doubling is designed to efficiently convert the continuous wave, infrared output of our lasers into low duty-cycle pulsed green output. This technique was verified through both computer modeling and experimentation. Further work would be necessary to develop a deliverable system using this technique.

Kane, Thomas J.↗
NASA NTRS1988

One-megawatt solar pumped and electrically driven lasers for space power transmission

High power lasers in space could provide power for a variety of future space missions such as spacecraft electric power requirements and laser propulsion. This study investigates four electrically pumped laser systems, krypton fluoride, copper vapor, laser diode array, and the carbon dioxide laser, all scaled to 1-MW laser output. Each system obtained its primary power from a large solar photovoltaic array which, in turn, provides power for the appropriate laser power conditioning subsystem. Each system was block-diagrammed, and the power and efficiency were found for each subsystem. The laser diode array had the highest solar-to-laser efficiency (6 percent) and smallest radiator area making it the most advantageous of the electrically driven lasers studied. This system was then compared with an iodine solar pumped laser system previously studied. The diode array had a better wavelength with regard to transmission optics mass, but it also had a heavier radiator because of its lower temperature radiator requirement. A more advanced solar pumped laser could emerge as the preferred laser system for space applications.

Deyoung, R. J.↗
NASA NTRS1988

OPO performance with a long pulse length, single frequency Nd:YAG laser pump

With the advent of new nonlinear materials and single-frequency pump sources, there is renewed interest in optical parametric oscillators (OPOs). A single-mode diode-laser-pumped monolithic Nd:YAG nonplanar ring laser that is both amplified and frequency doubled is used to pump a monolithic MgO:LiNbO3 pulsed singly resonant OPO. The OPO signal output was temperature tuned from 834 to 958 nm, producing an idler tuning from 1.47 to 1.2 microns. Efforts toward a CW all-solid-state doubly resonant OPO are also described.

Kozlovsky, W. J.↗
NASA NTRS1988

Integrated fountain effect pump device for fluid management at low gravity

A new device for fluid management at low gravity is described. The system is basically the same as the enclosed capillary device using screens, in which the screens along the gallery channels are replaced by porous plugs which are responsible for both the fluid retention and pumping of He II; in this device, no downstream pump is needed. The plugs in contact with liquid He on both sides act as a fountain-effect pumps (FEPs), while plugs exposed to vapor on one side behave as vapor-liquid phase separators (VLPSs). The total net rate of He II transfer into the receiving tank equals the mass flow rate through the FEP plugs minus the liquid loss from the VLPS plugs. The results of the performance analysis of this integrated FEP device are presented together with its schematic diagram.

Yuan, S. W. K.↗
NASA NTRS1989

Spin-lattice relaxation and the calculation of gain, pump power, and noise temperature in ruby

The use of a quantitative analysis of the dominant source of relaxation in ruby spin systems to make predictions of key maser amplifier parameters is described. The spin-lattice Hamiltonian which describes the interaction of the electron spins with the thermal vibrations of the surrounding lattice is obtained from the literature. Taking into account the vibrational anisotropy of ruby, Fermi's rule is used to calculate the spin transition rates between the maser energy levels. The spin population rate equations are solved for the spin transition relaxation times, and a comparison with previous calculations is made. Predictions of ruby gain, inversion ratio, and noise temperature as a function of physical temperature are made for 8.4-GHz and 32-GHz maser pumping schemes. The theory predicts that ruby oriented at 90 deg will have approximately 50 percent higher gain in dB and slightly lower noise temperature than a 54.7-deg ruby at 32 GHz (assuming pump saturation). A specific calculation relating pump power to inversion ratio is given for a single channel of the 32-GHz reflected wave maser.

Lyons, J. R.↗
NASA NTRS1990

Modeling of thermal lensing in side and end-pumped finite solid-state laser rods

An analytical expression for approximating the time-dependent thermal focal length in finite solid state laser rods was derived. The analysis is based on the temperature variation of the material refractive index caused by optical pumping of these rods. Several quantities were found to be relevant to this analysis. These quantities were the specific thermal profiles of the rods, type of optical pumping employed, type of cooling scheme employed (side and end-cooling parameters), and the specific material characteristics of the rods. The Thermal Lensing Model was formulated using the geometric ray tracing approach. The focal lengths are then approximated, by calculating the phase shift in the index of refraction, as the different rays of an incident plane wave are tracked through a lens-like crystal medium. The approach also applies in the case of Gaussian or parabolic pump beams. It is shown that the prediction of thermal focal length is in good quantitative agreement with experimentally obtained data.

Brackett, Vincent G.↗