SEARCH · Engineering Papers

Results for “polymer additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS2017

Monte Carlo Computational Modeling of Atomic Oxygen Interactions

Computational modeling of the erosion of polymers caused by atomic oxygen in low Earth orbit (LEO) is useful for determining areas of concern for spacecraft environment durability. Successful modeling requires that the characteristics of the environment such as atomic oxygen energy distribution, flux, and angular distribution be properly represented in the model. Thus whether the atomic oxygen is arriving normal to or inclined to a surface and whether it arrives in a consistent direction or is sweeping across the surface such as in the case of polymeric solar array blankets is important to determine durability. When atomic oxygen impacts a polymer surface it can react removing a certain volume per incident atom (called the erosion yield), recombine, or be ejected as an active oxygen atom to potentially either react with other polymer atoms or exit into space. Scattered atoms can also have a lower energy as a result of partial or total thermal accommodation. Many solutions to polymer durability in LEO involve protective thin films of metal oxides such as SiO2 to prevent atomic oxygen erosion. Such protective films also have their own interaction characteristics. A Monte Carlo computational model has been developed which takes into account the various types of atomic oxygen arrival and how it reacts with a representative polymer (polyimide Kapton H) and how it reacts at defect sites in an oxide protective coating, such as SiO2 on that polymer. Although this model was initially intended to determine atomic oxygen erosion behavior at defect sites for the International Space Station solar arrays, it has been used to predict atomic oxygen erosion or oxidation behavior on many other spacecraft components including erosion of polymeric joints, durability of solar array blanket box covers, and scattering of atomic oxygen into telescopes and microwave cavities where oxidation of critical component surfaces can take place. The computational model is a two dimensional model which has the capability to tune the interactions of how the atomic oxygen reacts, scatters, or recombines on polymer or nonreactive surfaces. In addition to the specification of atomic oxygen arrival details, a total of 15 atomic oxygen interaction parameters have been identified as necessary to properly simulate observed interactions and resulting polymer erosion that have been observed in LEO. The tuning of the Monte Carlo model has been accomplished by adjusting interaction parameters so the erosion patterns produced by the model match those from several actual LEO space experiments. Surface texturing in LEO can also be predicted by the model. Such comparison of space tests with ground laboratory experiments have enabled confidence in ground laboratory lifetime prediction of protected polymers. Results of Monte Carlo tuning, examples of surface texturing and undercutting erosion prediction, and several examples of how the model can be used to predict other LEO and Mars orbital space results are presented.

Atomic Oxygen↗

DOE OSTI2020

Controlling substrate temperature with infrared heating to improve mechanical properties of large-scale printed parts

Additively manufactured parts made with polymer extrusion techniques can be 50-75% weaker in the z-direction (across layers) than in the x- and y-directions. This has been attributed to poor mobility of polymer chains and a low degree of entanglement across a cold deposition interface. This is particularly a challenge when printing large-scale parts, such as with the Big Area Additive Manufacturing (BAAM) system, because layer times can exceed several minutes. The current work presents a method for controlling the temperature of the substrate material on the BAAM just prior to deposition using infrared heating lamps. Additionally, long layer times were simulated by actively cooling the material following deposition of each layer. The effect of substrate temperature on the z-direction mechanical properties of 20% carbon fiber reinforced acrylonitrile butadiene styrene (ABS) was measured for an initial temperature ranging from 50 °C to 150 °C and a preheated temperature ranging from 150 °C to 220 °C. Infrared preheating proved to be very effective when applied to substrates that had cooled considerably, almost doubling the tensile strength and increasing the fracture toughness by a factor of 7x.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Heat Exchanger Intensification Through Powder Processing and Enhanced Design (HIPPED)

High intensity, supercritical CO 2 heat exchangers capable of operating at temperatures between 800 and 1100 ˚C and pressures greater than 80 bar are considered a critical component for high efficiency power generation and a range of next-generation industrial processes. A novel heat exchanger concept was proposed in this project. The proposed concept involved a plate-type architecture with three-dimensional fins, called twisted s-shaped fins, that capitalize on additive manufacturing. Four manufacturing processes were studied to realize the complex envisioned design: press and sinter of metallic powders, directed energy deposition, laser powder bed fusion, and a novel powder bed process involving a photoreactive polymer called SEAM (scalable expeditious additive manufacturing), that later was developed at MSU. The team was able to manufacture subscale heat exchangers using laser powder bed fusion (LPBF) and SEAM. The team settled on using SEAM as a final manufacturing approach due to its very low cost. The SEAM-manufactured heat exchanger, however, when tested under pressure, exhibited leaks and the process still requires further development beyond the timeline of the project. To support the heat exchanger design and testing, the team developed a new high temperature flow loop allowing testing under high temperature and pressure. Computational modeling of the heat exchanger was also performed for the twisted s-shaped fins and the computations were validated with experimental data. The new twisted fins resulted in enhanced heat transfer and reduced pressure drop. To further minimize pressure drop in the plate heat exchanger, the team also developed a simplified model for flow maldistribution in the manifolds, providing a new tool for designers that eliminates the need for complex CFD calculations. A technoeconomic analysis was also developed to contrast SEAM with LPBF, this tool indicated that SEAM is several times less costly and offer significant promises as a rapid low cost additive manufacturing process for metallic systems.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

16.52% Efficiency All-Polymer Solar Cells with High Tolerance of the Photoactive Layer Thickness

All-polymer solar cells (all-PSCs) have drawn growing attention and achieved tremendous progress recently, but their power conversion efficiency (PCE) still lags behind small-molecule-acceptor (SMA)-based PSCs due to the relative difficulty on morphology control of polymer photoactive blends. Here, in this work, low-cost PTQ10 is introduced as a second polymer donor (a third component) into the PM6:PY-IT blend to finely tune the energy-level matching and microscopic morphology of the polymer blend photoactive layer. The addition of PTQ10 decreases the π–π stacking distance, and increases the π–π stacking coherence length and the ordered face-on molecular packing orientation, which improves the charge separation and transport in the photoactive layer. Moreover, the deeper highest occupied molecular orbital energy level of the PTQ10 polymer donor than PM6 leads to higher open-circuit voltage of the ternary all-PSCs. As a result, a PCE of 16.52% is achieved for ternary all-PSCs, which is one of the highest PCEs for all-PSCs. In addition, the ternary devices exhibit a high tolerance of the photoactive layer thickness with high PCEs of 15.27% and 13.91% at photoactive layer thickness of ≈205 and ≈306 nm, respectively, which are the highest PCEs so far for all-PSCs with a thick photoactive layer.

14 SOLAR ENERGY↗

NASA NTRS1991

High performance polymer development

The term high performance as applied to polymers is generally associated with polymers that operate at high temperatures. High performance is used to describe polymers that perform at temperatures of 177 C or higher. In addition to temperature, other factors obviously influence the performance of polymers such as thermal cycling, stress level, and environmental effects. Some recent developments at NASA Langley in polyimides, poly(arylene ethers), and acetylenic terminated materials are discussed. The high performance/high temperature polymers discussed are representative of the type of work underway at NASA Langley Research Center. Further improvement in these materials as well as the development of new polymers will provide technology to help meet NASA future needs in high performance/high temperature applications. In addition, because of the combination of properties offered by many of these polymers, they should find use in many other applications.

Hergenrother, Paul M.↗

NASA NTRS1986

Synthesis of Metal Phthalocyanine Sheet Polymers

New method for synthesizing metal phthalocyanine tetracarboxylic acids (MPTCA's) yields high purity end product. In addition, high-purity metal phthalocyanine sheet polymers synthesized from compounds. Monomer formed into sheet polymer by heating. Units of polymer linked in manner similar to phenyl-group linkages in biphenyl: Conjugation extends throughout macromolecule, thereby increasing delocalization of TT-electrons. Increases conductivity and thermal stability of polymer.

Achar, B. N.↗

DOE OSTI2021

Comparison of liquid absorption-release of superabsorbent polymers in alkali-activated slag and Portland cement systems: An NMR study combined with additional methods

In this study, {sup 1}H low-field NMR was used to compare the liquid absorption-release behaviour of superabsorbent polymers (SAPs) in Portland cement (PC) paste, NaOH-activated slag (SH-AAS) paste, and water glass-activated slag (WG-AAS) paste. The liquid absorption of SAPs in the PC paste was lower than that in the SH-AAS paste and the WG-AAS paste. The liquid release was also faster, which was mainly due to the higher Ca{sup 2+} concentration in the pore fluid of the PC system. In the AAS system, although the Ca{sup 2+} concentration in the pore fluid was low, the Na{sup +} concentration was much higher than that in the PC system due to the activator. The Ca{sup 2+} in the PC system is an important factor affecting the swelling of SAPs, while in the AAS system, the swelling limitation of SAPs is the result of the combined effects of Ca{sup 2+} and Na{sup +}, with Na{sup +} being dominant.

36 MATERIALS SCIENCE↗

DOE OSTI2026

3D printed water-stable Cd-doped Cs 4 MnBi 2 Cl 12 /polylactic acid perovskite/polymer composites for high-flux X-ray scintillation

Stable and efficient X-ray scintillators are crucial for medical diagnostics, industrial, and defense applications. However, conventional scintillator technologies face a trade-off between stability, optimal performance, and sustainability. Herein, we introduce 3D-printed Cs 4 MnBi 2 Cl 12 (Pero1) and Cs 4 Cd 0.68 Mn 0.32 Bi 2 Cl 12 (Pero2) perovskite microcrystals embedded within a polylactic acid (PLA) polymer composite as X-ray scintillators, combining efficiency, stability, and sustainability. The orange luminescent perovskite powder phosphors exhibited poor water stability, which was successfully addressed through incorporation into PLA via filament extrusion and fused deposition modeling (FDM) 3D printing. The resulting composite films demonstrated remarkable water stability while maintaining uniform orange emission throughout the polymer matrix, as confirmed by 3D topography scanning and X-ray fluorescence mapping. Structural characterization revealed minimal chemical interaction between the perovskite and PLA matrix, with the composites retaining their crystalline properties. The PLA-Pero2 composite exhibited superior optical properties, with a photoluminescence quantum yield of 47%, nearly 17 times higher than that of PLA-Pero1 (2.8%), attributed to the effective suppression of non-radiative decay pathways through Cd 2+ doping. Under hard X-ray irradiation at synchrotron beamlines, both composites exhibited excellent radioluminescence, with emission peaks at 605 nm, a linear response across a wide X-ray flux range, and remarkable radiation stability, showing less than 3% intensity degradation after 600 seconds of continuous high-dose exposure. The PLA-Pero2 composite achieved a spatial resolution of 5 line pairs per millimeter and a contrast ratio of 0.255. These performance metrics, combined with the polymer's biodegradability and scalability through additive manufacturing, position PLA-based composites as a more sustainable alternative to conventional petroleum-based polymer scintillators for next-generation medical imaging, radiation monitoring, and industrial radiography applications.

3D Printing↗

DOE OSTI2020

Natural optical activity as the origin of the large chiroptical properties in π-conjugated polymer thin films

Polymer thin films that emit and absorb circularly polarised light have been demonstrated with the promise of achieving important technological advances; from efficient, high-performance displays, to 3D imaging and all-organic spintronic devices. However, the origin of the large chiroptical effects in such films has, until now, remained elusive. We investigate the emergence of such phenomena in achiral polymers blended with a chiral small-molecule additive (1-aza[6]helicene) and intrinsically chiral-sidechain polymers using a combination of spectroscopic methods and structural probes. We show that – under conditions relevant for device fabrication – the large chiroptical effects are caused by magneto-electric coupling (natural optical activity), not structural chirality as previously assumed, and may occur because of local order in a cylinder blue phase-type organisation. This disruptive mechanistic insight into chiral polymer thin films will offer new approaches towards chiroptical materials development after almost three decades of research in this area.

36 MATERIALS SCIENCE↗

NASA NTRS2012

Large-Strain Transparent Magnetoactive Polymer Nanocomposites

A document discusses polymer nano - composite superparamagnetic actuators that were prepared by the addition of organically modified superparamagnetic nanoparticles to the polymer matrix. The nanocomposite films exhibited large deformations under a magnetostatic field with a low loading level of 0.1 wt% in a thermoplastic polyurethane elastomer (TPU) matrix. The maximum actuation deformation of the nanocomposite films increased exponentially with increasing nanoparticle concentration. The cyclic deformation actuation of a high-loading magnetic nanocomposite film was examined in a low magnetic field, and it exhibited excellent reproducibility and controllability. Low-loading TPU nanocomposite films (0.1-2 wt%) were transparent to semitransparent in the visible wavelength range, owing to good dispersion of the magnetic nanoparticles. Magnetoactuation phenomena were also demonstrated in a high-modulus, high-temperature polyimide resin with less mechanical deformation.

Meador, Michael A.↗

NASA NTRS2015

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing

In a NASA Aeronautics Research Institute (NARI) sponsored program entitled "A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing," evaluation of emerging materials and additive manufacturing technologies was carried out. These technologies may enable fully non-metallic gas turbine engines in the future. This paper highlights the results of engine system trade studies which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. In addition, feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composite were demonstrated. A wide variety of prototype components (inlet guide vanes (IGV), acoustic liners, engine access door, were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included first stage nozzle segments and high pressure turbine nozzle segments for a cooled doublet vane. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

Ceramic Matrix Composites↗

DOE OSTI2024

Upcycling linear low-density polyethylene waste to turbostratic graphene for high mass loading supercapacitors

Linear low-density polyethylene (LLDPE) waste is difficult to upcycle into more valuable carbon materials because it tends to completely decompose into small molecules during thermal processing. In this work, LLDPE is upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K 2 CO 3 ) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400–950°C without decomposition of the polymer feedstock. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800m 2 g -1 and average Raman I D /I G and I 2D /I G ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses a specific capacitance up to 175Fg -1 at a mass loading of 20mgcm -2 , which is two times the commercial requirement, yielding an areal capacitance of 3.5 Fcm -2 . Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8 % after 100,000 cycles at a current density of 4.0 Ag -1 . Additionally, the KCl and K 2 CO 3 solids are recycled and reused over 3 complete reaction cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling waste LLDPE and other varieties of polyethylene into a higher value graphene used for electrochemical energy storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Modifying the pore size distribution in Fe-rich inorganic polymer mortars: An effective shrinkage mitigation strategy

Highlights: • Inorganic polymer mortar has mainly macropores and a drying shrinkage of 5.1 mm/m. • 2-methyl-2,4-pentanediol acts as air entrainer in inorganic polymer mortars. • Optimal dosage 2 wt% 2-methyl-2,4-pentanediol reduced drying shrinkage to 1.8 mm/m. • Heat curing inorganic polymer mortars reduced drying shrinkage more than 50%. • Blast Furnace slag addition increased drying shrinkage and reduced strength. Inorganic polymer (IP) binder is formed upon alkali-activation of Fe-rich (41 wt%) metallurgical slag leading to materials with mechanical properties comparable to ordinary Portland cement binders. Crack formation is reported in IPs, which can be related to volumetric stability, which is to date not thoroughly understood in IPs. This study determined the autogenous and drying shrinkage of IP mortars. Shrinkage mitigation strategies, such as the addition of 2-methyl-2,4-pentanediol (2MPL), blast furnace slag (GGBFS), and applying heat curing, were used separately or in combination. IP mortars exhibited autogenous expansion and high drying shrinkage. The addition of 2MPL led to a porosity increase, as air was entrained, decreasing the drying shrinkage with 64%. Additional heat curing had no effect on samples with 2MPL. Introducing GGBFS resulted in smaller pores, increasing drying shrinkage. Shrinkage in IP mortars is driven by its pore size distribution and higher shrinkage resulted in lower flexural strength.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Developing Radiation Protection Garments with Additive Manufacturing

The RadWorks Wearable Technology team is dedicated to developing protective garments to ameliorate the effects of radiation caused by Solar Particle Events (SPEs). This work requires that we remain open to new avenues for processing hydrogen-rich materials that may be useful in the development of these protective garments. The purpose of this research was to identify new ways of processing polyolefin polymers (polypropylene, more specifically) with additive manufacturing techniques. First, we conducted a literature review to identify known problems with processing polypropylene using additive manufacturing. Then, we looked toward finding ways to manage these difficulties within the additive manufacturing process. The primary goal was to develop techniques for processing polypropylene in a way that would generate a product amenable to inclusion in a worn garment (e.g., flexible, strong, and with ample radiation protection). In the end, we were able to generate designs which addressed polypropylene’s high coefficient of thermal expansion and lack of material adhesion, while meeting the requirements set forth by the use-case for wearable technology. This research offers novel avenues for processing one of the most common plastics in the world, which could contribute to the development of protective garments, as well as new avenues to explore for additive manufacturing in low-gravity environments.

Additive Manufacturing, 3D Printing, Polypropylene↗

NASA NTRS1982

Countercurrent distribution of biological cells

It is known that the addition of phosphate buffer to two polymer aqueous phase systems has a strong effect on the partition behavior of cells and other particles in such mixtures. The addition of sodium phosphate to aqueous poly(ethylene glycol) dextran phase systems causes a concentration-dependent shift in binodial on the phase diagram, progressively lowering the critical conditions for phase separation as the phosphate concentration is increased. Sodium chloride produces no significant shift in the critical point relative to the salt-free case. Accurate determinations of the phase diagram require measurements of the density of the phases; data is presented which allows this parameter to be calculated from polarimetric measurements of the dextran concentrations of both phases. Increasing polymer concentrations in the phase systems produce increasing preference of the phosphate for the dextran-rich bottom phase. Equilibrium dialysis experiments showed that poly(ethylene glycol) effectively rejected phosphate, and to a lesser extent chloride, but that dextran had little effect on the distribution of either salt. Increasing ionic strength via addition of 0.15 M NaCl to phase systems containing 0.01 M phosphate produces an increased concentration of phosphate ions in the bottom dextran-rich phase, the expected effect in this type of Donnan distribution.

Source record↗

DOE OSTI2025

Multiplexing core & sheath extrusion system development for additive manufacturing for inner-bead multi-material capability

Single-feed polymer extruders are widely used in large-format additive manufacturing (AM) systems; however, the increasing demand for multi-material functionality within a single part has driven significant innovation in this field. One approach involves robotic pick-and-place operations, while another explores mechanical switching of feed lines during extrusion. Although robotic pick-and-drop systems offer flexibility, they introduce longer layer times during material changes, which can negatively affect the structural integrity of the part. On the other hand, mechanical feed switching causes delays in material transitions, as the existing material must be flushed before the new material emerges from the nozzle. This poses particular challenges for smaller or more intricate parts. In this study we are developing a unique multiplexing extrusion system with core & sheath nozzle that combines two extruders via co-extrusion. This allows for a unique inside and outside inner-bead (i.e., within the same bead) multi-material capability. We believe that this technology will allow for combining neat and filled materials, ductile and stronger materials, and many other combinations to address the problems aforementioned above and disrupt the AM technology creating new opportunities and opening application areas.

Tekinalp, Halil [ORNL]↗

DOE OSTI2026

Accelerating ion transport by dynamic asymmetry of alternating polymer electrolytes

Polymer based electrolytes allow the absence of volatile components in batteries thus increasing their safety. Yet, they exhibit drawbacks based on their low conductivity. We have used an alternating polymer consisting of dimethyl siloxane (DMS) and ethylene glycol (EG) blocks to circumvent known disadvantages of the usually used polyethylene glycol (PEG). Incorporating dimethyl siloxane lowers the glass-transition temperature and thus reduces the segmental relaxation time, by dynamic asymmetry or internal plasticization of the constituting polymer blocks. The alternating structure ensures miscibility of the different components and hinders crystallization. Furthermore, the pure polymer, P(DMS 3 -alt-EG 4 ), shows a segmental relaxation time well in the range needed for polymer electrolytes. Mixtures of LiClO 4 and P(DMS 3 -alt-EG 4 ) show a drastically reduced temperature dependence of their DC conductivity in comparison to PEG based systems, resulting in an increase by two orders of magnitude at T = 5 °C and even three to four orders of magnitude at T = 0 °C. Addition of coordinating (acetonitrile) or non-coordinating (toluene) solvent increases conductivity either via additional plasticization or by weakening the Li-binding yet looking at the dynamics at low concentrations of additional solvent the mobility of the polymer is reduced. In conclusion, the solvent addition leads only at higher solvent concentration to a reduction in relaxation time.

Jakobi, Bruno [Louisiana State Univ., Baton Rouge,↗

NASA NTRS1987

Synthesis and characterization of processable polyimides with enhanced thermal stability

Many of the emerging applications of polymers on space vehicles require materials with outstanding thermal stability. These polymers must also be readily processable in order to facilitate their use. The syntheses and polymerization of a cardo dianhydride were investigated. This monomer was prepared via the reaction of N-methyl 4-nitrophthalimide with a cardo diol. Polyimides containing oxyalkylene linkages were studied. The effects of two additional structural modifications on the polymers' properties were investigated. The effects of carrying out the preparation of poly(amic acid)s under non-equilibrium conditions were examined. Approaches that were investigated included the in-situ neutralization of the generated amic acid and its in-situ esterification.

Harris, Frank W.↗