Results for “oven” — Page 23

NASA NTRS2019

Manufacturing Process Development for Adhesively Bonded Joints in Large-Scale Space Structures

In order to take full advantage of the weight savings and performance gains offered by the use of composite materials in large-scale space structures, adhesively bonded joints must be considered. While bonded joint manufacturing at laboratory scale can be straightforward, the same manufacturing processes are not trivial at full scale. Surface preparation becomes particularly challenging (a viable process must yield consistent results over a large application area and be repeatable for multiple application sites), as does the application of heat to cure the doublers and/or bond them to the primary structure (the nature and scale of assembled or partially assembled aerospace structures often necessitates an out-of-oven/out-of-autoclave approach). In this work, bonded joint manufacturing processes are adapted for a full-scale (approximately 30 feet in diameter at the aft end) composite payload adapter at the NASA Marshall Space Flight Center. By iterating across a range of variables, process parameters for adhesively bonded joints on a large-scale composite structure have been developed. Primary findings are presented with respect to overarching bonded joint manufacturing concepts so as to maximize the applicability of this work to similar material systems and structures.

Guin, William E.↗

NASA NTRS2019

Evaluation of Temperature Gradients During Cure of a Thick Carbon Fiber/Epoxy Composite

The purpose of this study is to evaluate the development of thermal gradients throughout thick (1") carbon fiber composites and determine the effect of internal temperature distribution during cure on the observed mechanical properties in those composites. Composites up to 1.5" thick (56 plies) were fabricated with T700S/TC380 braided prepreg from Tencate following a modified vacuum bag layup procedure to include embedded thermocouples within the plies of the composite. Composite panels were cured in a programmable oven with thermocouple reading embedded throughout the panel thickness. Maximum temperature gradients measured between regions of the composite did not exceed 10 degrees C for any given composite thickness. The most significant temperature variation was measured between the mid-thickness plies and the tool-side surface plies. Although through thickness temperature variation during cure was small, a measureable variation in coupon glass transition temperature was recorded between the tool side plies and the remainder of the part, prior to post cure. Thermal and mechanical behavior of coupons taken from segments through the thickness of the part were comparable following a post-cure cycle.

Miller, Sandi↗

NASA NTRS2020

First Detections of Dichlorobenzene Isomers and Trichloromethylpropane from Organic Matter Indigenous to Mars Mudstone in Gale Crater, Mars: Results from the Sample Analysis at Mars Instrument Onboard the Curiosity Rover

Chromatographic analysis of the Cumberland mudstone in Gale crater by the Sample Analysis at Mars (SAM) instrument revealed the detection of two to three isomers of dichlorobenzene. Their individual concentrations were estimated to be in the 0.5–17 ppbw range relative to the sample mass. We also report the first detection of trichloromethylpropane and the confirmation of the detection of chlorobenzene previously reported. Supporting laboratory experiments excluded the SAM internal background as the source of those compounds, thus confirming the organic carbon and chlorine of the newly detected chlorohydrocarbons are indigenous to the mudstone sample. Laboratory experiments also demonstrated that the chlorohydrocarbons were mainly produced from chemical reactions occurring in the SAM ovens between organic molecules and oxychlorines contained in the sample. The results we obtained show that meteoritic organics and tested chemical species (a polycyclic aromatic hydrocarbon, an amino acid, and a carboxylic acid) were plausible organic precursors of the chlorinated aromatic molecules detected with SAM, thus suggesting that they could be among the organic molecules present in the mudstone. Results from this study coupled with previously reported detections of chlorinated aromatics (<300 ppbw) indigenous to the same mudstone highlight that organics can be preserved from the harsh surface conditions even at shallow depth. The detection of new chlorohydrocarbons with SAM confirms that organic molecules should have been available in an environment favorable to life forms, strengthening the habitability aspect of Gale crater. Key Words: Mars—Chlorinated organic molecules—In situ measurements—Sample Analysis at Mars— Mudstone—Gale crater. Astrobiology 20, 292–306.

Szopa, Cyril↗

NASA NTRS2019

Design and Analysis of a Tool for Automated Fiber Placement of Composite Wind Tunnel Blades

For decades, composite wind tunnel blades have been constructed using labor-intensive hand layup processes. Automated Fiber Placement (AFP) is a relatively new technology that has not seen widespread use in manufacturing composite wind tunnel blades. AFP offers the potential for reduced manufacturing time, reduced cost, and improved consistency compared to traditional hand layup procedures. These manufacturing qualities are becoming increasingly important as existing wind tunnel blades are replaced due to impact damage or wear and tear from decades of use. Researchers at the NASA Langley Research Center are currently using the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to investigate the feasibility of AFP for manufacturing composite wind tunnel blades. ISAAC uses manufacturing tools as surfaces on which to place fiber tows. A manufacturing tool was developed for using AFP to build a wind tunnel blade shape. This paper presents the structural design and analysis of this tool, for use with AFP, constructed from high temperature thermoplastics. The tool fabricated by this design process was successfully used for AFP and oven cure of two representative airfoil shaped composite structures.

Brian Mason↗

NASA NTRSDate not supplied

In-Situ Detection of Process-Induced Porosity During Cure of Out-of-Autoclave Composites

Composite materials offer unique benefits in aerospace applications and are becoming increasingly used by industry manufacturers. Current manufacturing and processing methods can lead to defects in the composites, which are identified after fabrication using inspection methods.This study utilized a high-temperature ultrasonic inspection system to detect process-induced porosity in an out-of-autoclave (OOA) composite panel. An ultrasonic scanner was enclosed in a nitrogen-cooled insulating box that prevented thermal damage from the industrial oven to the temperature-sensitive electronics. Inspection of the composite part was performed through the bottom of the enclosure, which served as the tool plate for the part. In this study, a porosity gradient was introduced through a misfit of the part and caul plate. Using the data obtained from B-scans and amplitude C-scans throughout the cure cycle, the high and low porosity regions within the composite laminate were detected and localized. OOA tests aided the transition of this system to an autoclave, which is the primary method of curing aerospace-grade thermoset composites.

In-process, Defect Detection, Cure Monitoring, Por↗

NASA NTRSDate not supplied

Process Development for Printing Copper Conductible Ink on Flexible Substrates Using Aerosol Jet Technology

Rise in demand for wearable consumer electronics products has given an impetus to the development of flexible electronics technology encompassing flexible substrates and compatible circuitry. Also, additive manufacturing of flexible electronics is emerging rapidly via several techniques such as Inkjet and Aerosol Jet Printing (AJP). The basic component of all flexible circuits to be printed by these technologies is conductible ink, which is generally silver ink. Few studies exist on the printing of copper conductible ink and not many copper ink formulations are available in the market as that of silver inks. This study aims to develop a process development study for deposition of copper conductible lines on flexible substrates using the aerosol jet printing technology. The process development study includes investigation of photosintering parameters for obtaining desirable electrical resistance and shear load to failure values for the printed line. Different pre-drying techniques such as oven pre-drying and platen pre-drying have been used for improving the electrical and mechanical properties of the conductive traces. Techniques such as optical microscopy and white light interferometry have been used for the characterization of print quality of the conductible lines.

printed electronics↗

NASA NTRSDate not supplied

Progress Towards Prolonged Deployment of SiC JFET-R ICs Into Previously Inaccessible Hostile Environments

This invited presentation describes demonstration of semiconductor integrated circuits (ICs) and ceramic packaging that are arguably the most environmentally durable transistor electronics ever demonstrated. SiC junction field effect transistor-resistor (JFET-R) ICs with two-level interconnect have successfully operated for over 1 year in 500 °C air-ambient [1], 60 days in 460 °C and 9.3 MPa pressure caustic Venus surface environment test chamber [2], and radiation exposure through 7 Mrad(Si) total ionizing dose (TID) and 86 MeV-cm2/mg heavy ion strikes [3]. Furthermore, these ICs have also demonstrated operation from -190 °C to +812 °C (over 1000 °C T-span) without significant change in signal (input /output) or power supply voltages [4]. With modest adjustments, the SiC JFET-R fabrication process is compatible with semiconductor mass-production tools and materials. As an initial step towards this end, the processing that forms the SiC JFETs and resistors (without interconnect) for the NASA Glenn “Generation 12” design prototype JFET-R ICs was conducted at GE Research. Once the COVID-delayed IC interconnect and bond pad fabrication processing on these wafers is completed at NASA Glenn, the resulting chips will be packaged and oven-tested [5]. It is expected that further technology transfer to complete commercial production will lower investment and risk barriers to useful application deployment. For NASA, an initial high-value deployment is opening the Venus surface to extended missions for robotic scientific exploration.

Silicon Carbide↗

NASA NTRSDate not supplied

Correlated Electromagnetic Levitation Actuator: A Reaction Sphere-Based Attitude Control System

To address problems experienced by current reaction wheels and control moment gyroscopebased attitude control systems (ACS), researchers at National Aeronautics and Space Administration’s (NASA’s) Marshall Space Flight Center (MSFC) have begun developing a reaction sphere actuator based on correlated electromagnetic levitation that will be immune to destructive bearing friction, momentum saturation, and gimbal lock. The Correlated Electromagnetic Levitation Actuator (CELA) advances the state of the art of reaction sphere ACSs by employing the concept of correlated magnetics. It is a frictionless, direct-drive reaction sphere that harnesses a unique technology with an array of applications across multiple disciplines. Correlated electromagnets function in a manner that is analogous to a matched filter; the convolution of two signals is peaked at the index representing the greatest match. For CELA, the signals are the patterns of magnetic flux density as a function of position. The magnitude of the convolution equates to an attractive or repulsive force, and these forces can be azimuthal or radial. The development of CELA is based in four distinct disciplines: Advanced Manufacturing, Prototype Development, Electromagnetic Modeling, and Controls. We are developing novel manufacturing techniques required to build arrays of permanent and electromagnet dipoles on curved surfaces. To print the permanent magnetic array, we have developed a probe with pyramidal magnets that will reside on a robotic arm to induce localized magnetic fields on a surface. We have also used high temperature ovens to erase dipole patterns from a permanent magnet by heating the surface to its Curie temperature. A number of test articles and prototypes have been developed using additive manufacturing methods. These prototypes have included hemispherical motors to test the drive algorithm, and a levitation test bed that demonstrates a magnetic bearing method based on attractive magnetic forces and ratiometric Hall effect sensors. We developed an array of electromagnetic dipoles on a printed circuit board (PCB) with individual H-bridges controlling each coil. This device created various flux density patterns and we measured their magnetic fields using a custom Hall effect 3-D probe and a LabVIEW virtual instrument. These data will serve as a benchmark for characterizing the accuracy of future models. Current work is focused on modeling the magnetic fields of our prototype arrays using COMSOL finite element analysis (FEA) and verifying the model against our test data. Accurate modeling will allow us to quickly test new patterns of electromagnets and their macro behavior. Eventually, the magnetic field models will be implemented in our controls simulations to facilitate precise control of the reaction sphere. Initial model results agree with field measurements to within 1 G (5% of measured flux density). Currently, we are testing different material properties of the electromagnets and their magnetic fields and thermal effects. These results will be used to refine the design of the electromagnetic dipoles. Our control efforts have centered on developing commutation, levitation, and field pattern shaping hardware in the form of breadboards and PCBs with software running on a local microcontroller. In addition, our partners developed MATLAB Simulink models to demonstrate a PID controller that mitigates disturbance forces resulting from the interaction of drive and levitation magnetics. Finally, we have designed a three-axis test stand that will be used in future work to demonstrate CELA’s orientation control capability.

reaction sphere↗

NASA NTRSDate not supplied

Meteorite Sample Section Repair at NASA Johnson Space Center

Introduction: Meteorite thin and thick sections are routinely shipped from NASA Johnson Space Center to fulfill sample allocation requests from principle investigators around the world. Sections are also re-turned to JSC when researchers are finished studying them since, in most cases, they can be reused for other studies. The sections are very fragile unfortunately, and sometimes return to us needing repairs. The fol-lowing should give you an idea of how we repair sections here in the very lab where they were created. NOTE: Please do not attempt to repair ANSMET meteorite sections that are in your possession. We will perform the repairs for you at NASA JSC if you send the section back to us. Section Delamination: The majority of the meteorite sections that we produce here are secured to the glass slide using a high quality, two-part epoxy. Occasionally, we are asked to use superglue if the researcher wishes to dismount the section from the slide. Both epoxy and superglue are excellent adhesives, but they both tend to embrittle with time which results in delamination from the slide. Exposure to vacuum can also degrade the adhesion between the sample section and the glass slide. Repeated handling of the slide edges can accelerate delamination and, as a preventive measure, the outer 1-2 mm of epoxy is trimmed from newly created sections at JSC. If conductive tapes (copper, carbon, etc.) are used on the section during analysis, great care must be taken in removing the tape so that the epoxy is not pulled up with it. If in doubt, the tape can be left on the section when it is returned to JSC. Before we perform any repairs to sample sections, carbon, gold, or other coatings are removed. We accomplish this using a slurry of 0.05 micron alumina and 190 proof ethyl alcohol applied to a felt polishing pad fitted to a rotating lap wheel. Coatings are re-moved in this manner from all sections that are re-turned to JSC. The extent of the delamination determines how we proceed with the section repair. If the meteorite sample area of the section is not disturbed, then we carefully remove the delaminated epoxy. This is done using a binocular microscope with a 6X zoom, cut-proof gloves, and a very sharp, single edged razor blade. We cut the delaminated epoxy with the blade angled away from the sample area and using very light pressure. The trimmed section is then cleaned in an ultrasonic bath of 200 proof ethyl alcohol for no more than 10 seconds and carefully dried using a lint-free clean room wipe. The section is then placed into a lab oven at 110o F in preparation for epoxy. We mix the resin and hardener components of the low viscosity epoxy and very small amounts are applied to the cut edges of the section using a needle probe and the binocular microscope. Warming the epoxy helps secure the existing section by filling any voids between the glass slide and the section. After the new epoxy cures, we give the section a light polish on a lap wheel fitted with cotton polishing paper that is charged with 1 micron diamond paste. If the section has delaminated to the point of sample area being lifted from the glass, then it may be irreparable. We employ the above technique along with clamping the section in a Teflon pad arrangement in order to flatten the sample while the epoxy cures. Otherwise, the sample will tend to curl. This works to some degree, but once the sample area curls, it seldom re-turns to the original flatness without cracking or bending. Canada Balsam and Crystalbond: We repair damaged sections that had originally been prepared using Canada Balsam or Crystalbond adhesives through the gradual application of heat. We take great care with these samples since these bonding materials tend to get brittle with age. The section is heated in gradual steps (40-50o F per hour) to the melting point of the adhesive. We repair the sample while the adhesive is fluid and then the section is cooled in the same gradual manner in which it was heated. Slide Cracks and Breaks: Accidents happen. Especially with something as small and fragile as a thin/thick section. We all know someone who has driven a microscope objective into a section. As bad as the damage may look, the section can be repaired in most instances. NOTE: Please do not try to tape or glue section pieces back together prior to returning the dam-aged section. This practice usually renders the section irreparable. If the glass slide is cracked but the section is still in one piece, we repair it by infilling the crack with the low viscosity epoxy mentioned earlier. If the slide is in pieces, we can reassemble it with epoxy on a new backer slide. This is a tricky task as the pieces need to be in the correct plane with respect to each other, especially if the sample area is split among several pieces.

Meteorite↗

NASA NTRSDate not supplied

Early Burn-In Parasitic Conduction in 500 °C Durable SiC JFET ICs

All prior reports of long-term 500 °C operation of SiC JFET-R ICs have noted the existence of an initial “burn-in” period of changes in measured electrical characteristics for the first few hundred hours oven-testing. This work reports measurements of “burn-in parasitic MOSFET conduction” that can substantially impact the performance of some circuits during initial heat-up of JFET ICs, but then subsequently disappears after a few hours of operation at 500 °C. The behavior appears generally consistent with the known MOS phenomenon of bias-temperature driven redistribution of mobile ionic contamination. Approaches for further mitigating this initial burn-in conduction mechanism are discussed.

silicon carbide↗

NASA NTRSDate not supplied

Early Burn-In Parasitic Conduction in 500 °C Durable SiC JFET ICs

All prior reports of long-term 500 °C operation of SiC JFET-R ICs have noted the existence of an initial “burn-in” period of changes in measured electrical characteristics for the first few hundred hours oven-testing. This work reports measurements of “burn-in parasitic MOSFET conduction” that can substantially impact the performance of some circuits during initial heat-up of JFET ICs, but then subsequently disappears after a few hours of operation at 500 °C.

silicon carbide↗

NASA NTRS2023

High-Pressure, Normal-Gravity Droplet Combustion Experimental Hardware

The High-Pressure, Trans-Critical (HPTC) 1-g Liquid Droplet Combustion Experiments will assess the autoignition and combustion of liquid fuel droplets at elevated temperatures and pressures. These experiments are being conducted at the NASA Glenn Research Center in a manner similar to experiments performed in Glenn’s Zero Gravity Research Facility (ZGF) using the B drop vehicle. The modification to the test capabilities of the ZGF experiments in the new experimental configuration will allow researchers to continue performing normal-gravity liquid droplet combustion experiments without requiring the use of the ZGF test equipment. These normal-gravity experiments will be conducted at lower pressures than in the ZGF because the pressure vessel for this setup is limited to a maximum working pressure of 7.74 atm (99.1 psig) at 366.5 K (200 °F). This experimental configuration will enable development of a similar capability for conducting high-pressure combustion and supercritical oxidation research on the International Space Station. Experiments will be conducted with the capability of altering the ambient pressure, temperature, and gas concentrations, as well as the fuel type for each test. For these experiments, the test vessel operates at pressures up to 7.5 atm (95.5 psig), temperatures up to 1,073 K (1,472 °F) inside the insulated oven, and oxygen concentrations up to 30 percent.

Droplet Combustion↗

NASA NTRSDate not supplied

Electrical and Dielectric Characterizations of HTCC Electronic Packages for High Temperature Harsh Environment Applications

A prototype high temperature co-fired ceramic (HTCC) alumina packaging system composed of a 32-I/Os package and a compatible circuit board was previously developed and demonstrated for long term operation in 500 °C environments. The electrical / dielectric parasitic parameters of that chip level package were characterized and reported. This co-fired packaging system with platinum (Pt) conductor has successfully facilitated tests of silicon carbide (SiC) analog and digital integrated circuits (ICs) developed at NASA GRC at 500°C for up to 10,000 hours in ambient oven environment and 60 earth days in Venus surface environment with simulated temperature, pressure, and chemical constituents. Based on these previous results, this paper introduces new designs of Pt-HTCC packages with 16, 24, and 44 I/Os for packaging a new generation SiC ICs with 8, 24, 56, 62, and 72 I/Os to be tested in high temperature harsh environments. The package with 44 I/Os is specifically designed for the new SiC ICs with 56, 62, and 72-I/Os and electrical connection needs, the power pads of this package are consolidated, and an array of I/O pads distributed on separated vertical levels (inside the package) is used to control the overall package dimensions and mitigate the parasitic effects at high temperatures. This paper will present the detailed design of these chip-level packages and results of electrical and dielectric characterization of these newly fabricated chip-level Pt-HTCC packages.

High temperature↗

NASA NTRSDate not supplied

Electrical and Dielectric Characterizations of HTCC Electronic Packages for High Temperature Harsh Environment Applications

A prototype high temperature co-fired ceramic (HTCC) alumina packaging system composed of a 32-I/Os package and a compatible circuit board was previously developed and demonstrated for long term operation in 500 °C environments. The electrical / dielectric parasitic parameters of that chip level package were characterized and reported. This co-fired packaging system with platinum (Pt) conductor has successfully facilitated tests of silicon carbide (SiC) analog and digital integrated circuits (ICs) developed at NASA GRC at 500°C for up to 10,000 hours in ambient oven environment and 60 earth days in Venus surface environment with simulated temperature, pressure, and chemical constituents. Based on these previous results, this paper introduces new designs of Pt-HTCC packages with 16, 24, and 44 I/Os for packaging a new generation SiC ICs with 8, 24, 56, 62, and 72 I/Os to be tested in high temperature harsh environments. The package with 44 I/Os is specifically designed for the new SiC ICs with 56, 62, and 72-I/Os and electrical connection needs, the power pads of this package are consolidated, and an array of I/O pads distributed on separated vertical levels (inside the package) is used to control the overall package dimensions and mitigate the parasitic effects at high temperatures. This paper will present the detailed design of these chip-level packages and results of electrical and dielectric characterization of these newly fabricated chip-level Pt-HTCC packages.

High temperature↗

NASA NTRS2023

Dynamic Crush Performance of Thermoplastic and Resin Infused Thermoset Triaxially Braided Composite Structures

Dynamic crush tests were conducted on triaxially braided composite tubes and C-channel structural elements to measure their relative energy absorbing characteristics. The elements were manufactured from triaxially braided [0/+60/-60] T700 fiber preforms with two different resin systems, a PR520 thermoset resin and a LM-PAEK thermoplastic resin. T700/PR520 composite tubes and C-channel elements were manufactured using a resin infusion process. T700GC/LMPAEK composite tubes were manufactured by braiding slit tape prepreg onto cylindrical mandrels. Consolidation pressure was applied through thermally activated shrink tape in an oven. The energy absorbing characteristics of the composite elements were measured using a pneumatically actuated sled with a flat-faced impacting mass, which provided several independent measurements of force, displacement, and energy absorption. The parameter primarily used for comparison between the systems was the specific energy absorption (SEA), a measure of energy absorbed per unit crushed length. The T700/LMPAEK tubes performed slightly better than T700/PR520 tubes, with an approximately 9% higher SEA. T700/PR520 tubes had over 20% higher SEA than C-channels made from the same material. Additional tests were conducted on tubes using a tapered-conical impactor to force the tubes to fail in circumferential tension. This type of impact significantly reduced the energy absorption.

Composite Materials↗

NASA NTRS2023

Dynamic Crush Performance of Thermoplastic and Resin Infused Thermoset Triaxially Braided Composite Structures

Dynamic crush tests were conducted on triaxially braided composite tubes and C-channel structural elements to measure their relative energy absorbing characteristics. The elements were manufactured from triaxially braided [0/+60/-60] T700 fiber preforms with two different resin systems, a PR520 thermoset resin and a LM-PAEK thermoplastic resin. T700/PR520 composite tubes and C-channel elements were manufactured using a resin infusion process. T700GC/LMPAEK composite tubes were manufactured by braiding slit tape prepreg onto cylindrical mandrels. Consolidation pressure was applied through thermally activated shrink tape in an oven. The energy absorbing characteristics of the composite elements were measured using a pneumatically actuated sled with a flat-faced impacting mass, which provided several independent measurements of force, displacement, and energy absorption. The parameter primarily used for comparison between the systems was the specific energy absorption (SEA), a measure of energy absorbed per unit crushed length. The T700/LMPAEK tubes performed slightly better than T700/PR520 tubes, with an approximately 9% higher SEA. T700/PR520 tubes had over 20% higher SEA than C-channels made from the same material. Additional tests were conducted on tubes using a tapered-conical impactor to force the tubes to fail in circumferential tension. This type of impact significantly reduced the energy absorption.

Composite Materials↗

NASA NTRSDate not supplied

Laser Sintering of RTM385-SLS Thermoset Polyimides With Boron Nitride

RTM385-SLS is a melt-processable thermoset polyimide resin specially formulated with a complex melt viscosity (ƞ*) of ~104-105 poise for laser sintering. RTM385-SLS resin powder was mixed with 20-25% of hexagonal boron nitride (h-BN) and subjected to laser sintering (LS) to print out “Green” disks and dogbone specimens which could be further post-cured in an oven to complete the crosslinking of the reactive phenylethynyllphthalic anhydride (PEPA) terminal groups within the resin to achieve a very high glass transition temperature (T g ) of 385°C. The cured composite specimens were then subjected to thermal analysis, thermal conductivity measurement and mechanical testing for characterization.

Additive manufacturing↗

NASA NTRSDate not supplied

Nutrition of Antarctic-grown Crops to Supplement the Crew Diet, with Applications for Spaceflight

The availability of fresh produce during longer-duration spaceflight missions is being explored as a countermeasure for human biobehavioral health and performance, including how fresh fruits and vegetables can supplement the crew diet with nutrients that are predicted to become deficient throughout the missions. Crop production in the Veggie and Advanced Plant Habitat vegetable production chambers on the International Space Station (ISS) have tested pick-and-eat crops in spaceflight. However, the limited plant cultivation volume of these chambers has restricted the sample sizes and biomass allocated for nutrition assessment. To gain a better understanding of the nutrient composition of pick-and-eat crops, leafy greens and fruiting plants were grown in the EDEN ISS plant cultivation facility near the German Neumayer Station III in Antarctica from March 2021 to January 2022. Target crops for nutrition sampling aligned with cultivars grown in spaceflight, including ‘Outredgeous’ red romaine lettuce, Mizuna mustard, ‘Red Robin’ dwarf cherry tomato, and NuMex ‘Española Improved’ chili pepper. Plants subsamples were taken at harvest; in the event of multiple harvests from the same plants, subsamples were taken at both the first and final harvests. ‘Outredgeous’ and Mizuna were also grown multiple times throughout the year, allowing multiple grow-outs to be analyzed for potential effects across the growing season. Subsamples were first weighed for fresh mass, dried in a dedicated oven at 70°C for 96 h, weighed again, and stored in air-tight containers inside Neumayer Station III. At the beginning of 2022, the samples were shipped to NASA’s Kennedy Space Center, where they are currently being analyzed with ion chromatography for nutrients of interest in the astronaut diet, including calcium, iron, magnesium, and potassium. This study aims to increase our understanding of how the crops that have successfully grown on the ISS can supplement the crew diet, as well as how other factors like plant age and the number of days the facility has been in operation may impact nutrient concentrations. Such findings can improve the crop selection process and how pick-and-eat crops are cultivated during spaceflight missions.

Jess M. Bunchek↗