SEARCH · Engineering Papers

Results for “optimized”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Solution of transient optimization problems by using an algorithm based on nonlinear programming

An algorithm is presented for solution of dynamic optimization problems which are nonlinear in the state variables and linear in the control variables. It is shown that the optimal control is bang-bang. A nominal bang-bang solution is found which satisfies the system equations and constraints, and influence functions are generated which check the optimality of the solution. Nonlinear optimization (gradient search) techniques are used to find the optimal solution. The algorithm is used to find a minimum time acceleration for a turbofan engine.

Teren, F.↗

NASA NTRS1977

Optimal filtering and filter stability of linear stochastic delay systems

Optimal filtering equations are obtained for very general linear stochastic delay systems. Stability of the optimal filter is studied in the case where there are no delays in the observations. Using the duality between linear filtering and control, asymptotic stability of the optimal filter is proved. Finally, the cascade of the optimal filter and the deterministic optimal quadratic control system is shown to be asymptotically stable as well.

Kwong, R. H.-S.↗

NASA NTRS1977

Optimal low-thrust takeoff from an orbit about an oblate planet

Future space missions to the outer planets may depend upon the use of low-thrust propulsion systems. As these planets are decidedly oblate, the question of the effect of that oblateness on a low-thrust trajectory is of some interest. In this paper the problem of optimal energy increase is attacked under the assumption that the coefficients for the second zonal harmonic, and the nondimensional thrust acceleration are the same order of magnitude. By means of a two-variable asymptotic expansion technique, a near optimal control program is generated and the first-order uniformly valid approximation for the corresponding trajectory is obtained. Tangential thrust is shown to be a good near-optimal thrust program even in the presence of oblateness effects. The optimal control program is found to be oscillatory and quite similar to the optimal control for energy increase in an inverse square gravitational field.

Jacobson, R. A.↗

NASA NTRS1976

The computer for design and optimization

Computerized design using numerical optimization techniques is discussed and guidelines for writing analysis computer codes that can be readily coupled to optimization codes are presented. The following numerical optimization techniques are examined: random search, sequential unconstrained minimization, direct constrained optimization, and one-dimensional search. A number of design applications are considered including high speed airfoil lift maximization, the preliminary design of a wing, design of a planar tower for optimal geometry, and the conceptual design of a tactical fighter aircraft.

Vanderplaats, G. N.↗

NASA NTRS1978

Determination of optimal control using imbedding of the terminal conditions

The utility of a method to solve optimal control problems is discussed with emphasis placed on the solutions of singular optimal control problems. The method involves imbedding the optimization problem of interest in a family of optimization problems which are parameterized by their terminal conditions. The solution to the optimization problem is obtained by collapsing the terminal conditions of the family of problems onto those of the original problem, while appropriately modifying the control function to account for the changing terminal conditions. The utility of this method is illustrated by obtaining the solution to an aerial attack problem where the attacking vehicle must maneuver subject to control limitations so as to place the enemy in a certain relative position for launching a missile in the shortest possible time.

Montgomery, R. C.↗

NASA NTRS1978

Computational wing optimization and comparisons with experiment for a semi-span wing model

A computational wing optimization procedure was developed and verified by an experimental investigation of a semi-span variable camber wing model in the NASA Ames Research Center 14 foot transonic wind tunnel. The Bailey-Ballhaus transonic potential flow analysis and Woodward-Carmichael linear theory codes were linked to Vanderplaats constrained minimization routine to optimize model configurations at several subsonic and transonic design points. The 35 deg swept wing is characterized by multi-segmented leading and trailing edge flaps whose hinge lines are swept relative to the leading and trailing edges of the wing. By varying deflection angles of the flap segments, camber and twist distribution can be optimized for different design conditions. Results indicate that numerical optimization can be both an effective and efficient design tool. The optimized configurations had as good or better lift to drag ratios at the design points as the best designs previously tested during an extensive parametric study.

Waggoner, E. G.↗

NASA NTRS1977

Solution of transient optimization problems by using an algorithm based on nonlinear programming

A new algorithm is presented for solution of dynamic optimization problems which are nonlinear in the state variables and linear in the control variables. It is shown that the optimal control is bang-bang. A nominal bang-bang solution is found which satisfies the system equations and constraints, and influence functions are generated which check the optimality of the solution. Nonlinear optimization (gradient search) techniques are used to find the optimal solution. The algorithm is used to find a minimum time acceleration for a turbofan engine.

Teren, F.↗

NASA NTRS1979

Application of numerical optimization to the design of advanced supercritical airfoils

An application of numerical optimization to the design of advanced airfoils for transonic aircraft showed that low-drag sections can be developed for a given design Mach number without an accompanying drag increase at lower Mach numbers. This is achieved by imposing a constraint on the drag coefficient at an off-design Mach number while minimizing the drag coefficient at the design Mach number. This multiple design-point numerical optimization has been implemented with the use of airfoil shape functions which permit a wide range of attainable profiles during the optimization process. Analytical data for the starting airfoil shape, a single design-point optimized shape, and a double design-point optimized shape are presented. Experimental data obtained in the NASA Ames two-by two-foot wind tunnel are also presented and discussed.

Johnson, R. R.↗

NASA NTRS1980

Application of an advanced trajectory optimization method to ramjet propelled missiles

The mission performance characteristics of ramjet-propelled missiles are highly dependent upon the trajectory flown. Integration of the trajectory profile with the ramjet propulsion system performance characteristics to achieve optimal missile performance is very complex. Past trajectory optimization methods have been extremely problem dependent and require a high degree of familiarity to achieve success. A general computer code (CTOP) has been applied to ramjet-powered missiles to compute open-loop optimal trajectories. CTOP employs Chebyshev polynomial representations of the states and controls. This allows a transformation of the continuous optimal control problem to one of parameter optimization. With this method, the trajectory boundary conditions are always satisfied. State dynamics and path constraints are enforced via penalty functions. The presented results include solutions to minimum fuel-to-climb, minimum time-to-climb, and minimum time-to-target intercept problems.

Paris, S. W.↗

NASA NTRS1980

Flat-plate photovoltaic array design optimization

An analysis is presented which integrates the results of specific studies in the areas of photovoltaic structural design optimization, optimization of array series/parallel circuit design, thermal design optimization, and optimization of environmental protection features. The analysis is based on minimizing the total photovoltaic system life-cycle energy cost including repair and replacement of failed cells and modules. This approach is shown to be a useful technique for array optimization, particularly when time-dependent parameters such as array degradation and maintenance are involved.

Ross, R. G., Jr.↗

NASA NTRS1982

Optimization of composite structures

Structural optimization is introduced and examples which illustrate potential problems associated with optimized structures are presented. Optimized structures may have very low load carrying ability for an off design condition. They tend to have multiple modes of failure occurring simultaneously and can, therefore, be sensitive to imperfections. Because composite materials provide more design variables than do metals, they allow for more refined tailoring and more extensive optimization. As a result, optimized composite structures can be especially susceptible to these problems.

Stroud, W. J.↗

NASA NTRS1982

Optimization of Dish Solar Collectors with and without Secondary Concentrators

Methods for optimizing parabolic dish solar collectors and the consequent effects of various optical, thermal, mechanical, and cost variables are examined. The most important performance optimization is adjusting the receiver aperture to maximize collector efficiency. Other parameters that can be adjusted to optimize efficiency include focal length, and, if a heat engine is used, the receiver temperature. The efficiency maxima associated with focal length and receiver temperature are relatively broad; it may, accordingly, be desirable to design somewhat away from the maxima. Performance optimization is sensitive to the slope and specularity errors of the concentrator. Other optical and thermal variables affecting optimization are the reflectance and blocking factor of the concentrator, the absorptance and losses of the receiver, and, if a heat engine is used, the shape of the engine efficiency versus temperature curve. Performance may sometimes be improved by use of an additional optical element (a secondary concentrator) or a receiver window if the errors of the primary concentrator are large or the receiver temperature is high.

Jaffe, L. D.↗

NASA NTRS1981

Optimal searches for asteroids

Optimal searches for a fixed object are discussed, and the rigorous analytical results of discrete search theory are presented. The totally optimal, the uniformly optimal, the locally optimal, and the fastest searches are shown to be identical under not too restrictive assumptions. The mathematical formalism is illustrated by an Earth-approaching asteroid search and optimal searches for such objects are explicitly constructed. The approximation that Earth-approaching asteroids are fixed is equivalent to having a very high ( equiv 100 sq degs/hour) search rate. Generalizations to other types of astronomical search are briefly mentioned.

Taff, L. G.↗

NASA NTRS1982

Optimal turning climb-out and descent of commercial jet aircraft

Optimal turning climb-out and descent flight-paths from and to runway headings are derived to provide the missing elements of a complete flight-path optimization for minimum fuel consumption. The paths are derived by generating a field of extremals, using the necessary conditions of optimal control. Results show that the speed profiles for straight and turning flight are essentially identical, except for the final horizontal accelerating or decelerating turn. The optimal turns, which require no abrupt maneuvers, could easily be integrated with present climb-cruise-descent fuel-optimization algorithms.

Neuman, F.↗

NASA NTRS1984

Optimization of thermal systems with sensitive optics, electronics, and structures

A strategy was investigated by which thermal designers for spacecraft could devise an optimal thermal control system to maintain the required temperatures, temperature differences, changes in temperature, and changes in temperature differences for specified equipment and elements of the spacecraft's structure. Thermal control is to be maintained by the coating pattern chosen for the external surfaces and heaters chosen to supplement the coatings. The approach is to minimize the thermal control power, thereby minimizing the weight of the thermal control system. Because there are so many complex computations involved in determining the optimal coating design a computerized approach was contemplated. An optimization strategy including all the elements considered by the thermal designer for use in the early stages of design, where impact on the mission is greatest, and a plan for implementing the strategy were successfully developed. How the optimization process may be used to optimize the design of the Space Telescope as a test case is demonstrated.

Bettini, R. G.↗

NASA NTRS1984

Application of an optimization method to high performance propeller designs

The application of an optimization method to determine the propeller blade twist distribution which maximizes propeller efficiency is presented. The optimization employs a previously developed method which has been improved to include the effects of blade drag, camber and thickness. Before the optimization portion of the computer code is used, comparisons of calculated propeller efficiencies and power coefficients are made with experimental data for one NACA propeller at Mach numbers in the range of 0.24 to 0.50 and another NACA propeller at a Mach number of 0.71 to validate the propeller aerodynamic analysis portion of the computer code. Then comparisons of calculated propeller efficiencies for the optimized and the original propellers show the benefits of the optimization method in improving propeller performance. This method can be applied to the aerodynamic design of propellers having straight, swept, or nonplanar propeller blades.

Li, K. C.↗

NASA NTRS1984

Aerospace engineering design by systematic decomposition and multilevel optimization

A method for systematic analysis and optimization of large engineering systems, by decomposition of a large task into a set of smaller subtasks that is solved concurrently is described. The subtasks may be arranged in hierarchical levels. Analyses are carried out in each subtask using inputs received from other subtasks, and are followed by optimizations carried out from the bottom up. Each optimization at the lower levels is augmented by analysis of its sensitivity to the inputs received from other subtasks to account for the couplings among the subtasks in a formal manner. The analysis and optimization operations alternate iteratively until they converge to a system design whose performance is maximized with all constraints satisfied. The method, which is still under development, is tentatively validated by test cases in structural applications and an aircraft configuration optimization.

Sobieszczanski-Sobieski, J.↗

NASA NTRS1983

Optimization of dish solar collectors

Jaffe, L. D.↗