Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nanostructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Insight into the nanostructure of “water in salt” solutions: A SAXS/WAXS study on imide-based lithium salts aqueous solutions

"Water-in-salt " electrolyte (WISE) series have been studied for lithium-ion batteries and supercapacitor applications, but so far, most of the focus has been on the LiTFSI salt-based systems. Herein, we used small-angle X-ray scattering/wide-angle X-ray scattering (SAXS/WAXS) and molecular dynamics (MD) simulation to investigate the solvation structure of a series of lithium salts with four different symmetric anions: (bis(fluoro sulfonyl)imide (FSI), bis(trifluoromethane sulfonyl)imide (TFSI), bis(pentafluoroethane sulfonyl) imide (BETI) and bis(nonafluorobutane sulfonyl)imide (BNTI)), which have similar parent structures but different lengths of the fluorocarbon chains. Two competing structures were found in the four lithium salts aqueous solutions: anion solvated structure and anion network. The anion network plays a crucial role in obtaining a stable and enlarged electrochemical window. The d spacing of the anion solvated structure follows a linear correlation with the number of carbons in the fluorocarbon chains and an exponential correlation with the concentrations. Further, we also observed that the transition from one structure to another is predominantly controlled by the salt volume fraction for all imide-based aqueous solutions. This work provides a systematic study of the atomistic scale structures of a series of imide-based lithium salt aqueous solutions that could extend the knowledge of WIS electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Thermoelectric performance in disordered Cu 2 ZnSnSe 4 nanostructures driven by ultra-low thermal conductivity

Here, high-energy reactive mechanical alloying (ball milling) was used to synthesize tetragonal and cubic polymorphs of Cu 2 ZnSnSe 4 . The ordered tetragonal (I-4) polymorph undergoes a phase transition above 400 K into a Cu-Zn disordered tetragonal (I-42 m) polymorph, while the cubic (F-43 m) polymorph with full cation disorder is stabilized at room temperature. Both polymorphs show ultra-low thermal conductivities, 0.42 W m -1 K -1 at 722 K and 0.21 W m -1 K -1 at 523 K for the disordered tetragonal and cubic phases respectively. The cubic polymorph has a higher zT in the low-temperature range, peaking at 0.26 (523 K), while the disordered tetragonal has a maximum zT of 0.46 at 712 K. The latter is the highest reported zT for stoichiometric Cu 2 ZnSnSe 4 , comparable to the best-performing doped materials in the literature. A combination of experimental results and ab-initio calculations point to a coupling between structural disorder and microstructure as the mechanism behind the reported performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanostructured ligament and fiber Al–doped Li 7 La 3 Zr 2 O 12 scaffolds to mediate cathode-electrolyte interface chemistry

In this study, scaffold structures of electrospun aluminum–substituted lithium lanthanum zirconate Li 7 La 3 Zr 2 O 12 (Al-LLZO) were synthesized and used as an additive in a LiNi 0.6 Mn 0.2 Co 0.2 O 2 composite cathode. The scaffolds were crystalized in the cubic phase after calcination at 700 °C. The Al-LLZO scaffold morphology was dependent on the precursor formulation (aqueous and dimethylformamide. The aqueous precursors resulted in scaffolds of densely coalesced ligaments, whereas the dimethylformamide precursors resulted in high–aspect ratio nanofiber scaffolds. The long-term cycling stability and rate performance of the cells were found to depend on the Al-LLZO scaffold morphology. The uniformly dispersed Al-LLZO fibers resulted in a more stable cathode electrolyte interface formation through the reduced decomposition of the LiPF 6 salt during cycling, resulting in a better high-rate and long-term cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Nanostructure refinement and phase formation of flash annealed FeNi-based soft magnetic alloys

In this work, the resulting nanocomposite microstructures of FeNi nanocrystallites under different heating and cooling rates (5 °C/min vs 400-500 °C/s) is investigated. Conventional furnace annealing under low heating rates and slow cooling resulted in both BCC α-FeNi and FCC γ-FeNi nanocrystallites with an average grain size on the order of 25-27 nm whereas high heating rates achieved via flash annealing techniques have enabled a dramatically refined microstructure consisting of 5-7 nm grains with FCC γ-FeNi phase and found to be the dominant phase following primary crystallization. Grain size refinement and phase identity optimization yielded low values of coercivities-17 A/m and high permeability similar to 11 x 10 3 measured at 400 Hz/1 kA/m in flash annealed samples at 450 °C for 5 s. The magnetic behavior and the underlying mechanism of optimal soft magnetic properties are discussed in terms of the critical role of the grain size in domain wall pinning and coercivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermally induced structural evolution and nanoscale interfacial dynamics in Bi-Sb-Te layered nanostructures

Layered chalcogenides, including Bi-Sb-Te ternary alloys and heterostructures, are renowned as thermoelectric and topological insulators and have recently been highlighted as plasmonic building blocks beyond noble metals. Here, we conduct joint in situ transmission electron microscopy and density functional theory calculations to investigate the temperature-dependent nanoscale dynamics and interfacial properties, identifying the role of native defects and edge configurations in the anisotropic sublimation of Bi 2 Te 3 -Sb 2 Te 3 heterostructures and Sb 2-x Bi x Te 3 alloys. We report structural dynamics, including edge evolution, layer-by-layer sublimation, and the formation and coalescence of thermally induced polygonal nanopores. These nanopores are initiated by preferential dissociation of tellurium, reducing thermal stability in heterostructures. Triangular and quasi-hexagonal configurations dominate nanopore structures in heterostructures. Our calculations reveal antisite defects (Te Sb and Te Bi ) as key players in defect-assisted sublimation. These findings enhance our understanding of nanoscale dynamics and assist in designing tunable low-dimensional chalcogenides.

Bi2Te3-Sb2Te3 heterostructure↗
DOE OSTI2023

ZnO/CuO nanostructures anchored over Ni/Cu tubular films via pulse electrodeposition for photocatalytic and antibacterial applications

In this work, we report the fabrication of Ni and Cu tubular substrates and the synthesis of ZnO/CuO nanocomposite on them through the process of pulse electrodeposition. The systematic variation in CuO incorporation in the ZnO matrix and the processing technique were noticed to affect the structural, optical, photocatalytic, and anti-bacterial properties, which are well in accordance with the Field Emission-Scanning Electron Microscope, X-ray Diffraction, Fourier transform Infrared Spectroscopy and UV-Differential reflectance spectroscopy results. The remediation capabilities of the photocatalytic substrates were assessed through the degradation of methylene blue (MB) dye under solar irradiation. Optimized CuO incorporation within the ZnO nanorods resulted in the degradation of a 20 ppm of MB dye solution within 40 min and a higher concentration of 50 ppm within 95 min. The Ni and Cu electroformed tubes as substrates provided not only a reusable supporting frame but also a large surface-area for the growth of ZnO/CuO nanocomposite. The current study also dealt with the anti-bacterial efficacy of the above-mentioned substrates against E.coli. Hence, the Ni and Cu tubular thin film substrates with nanorods of ZnO/CuO composite were explored for the removal of organic as well as biological contaminants from waste water.

36 MATERIALS SCIENCE↗