Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lightweight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Orthotic devices using lightweight composite materials

Potential applications of high strength, lightweight composite technology in the orthotic field were studied. Several devices were designed and fabricated using graphite-epoxy composite technology. Devices included shoe plates, assistive walker devices, and a Simes prosthesis reinforcement. Several other projects having medical application were investigated and evaluations were made of the potential for use of composite technology. A seat assembly was fabricated using sandwich construction techniques for the Total Wheelchair Project.

Harrison, E., Jr.↗

Optimum shapes for lightweighted mirrors

Two types of monolithic lightweight mirrors with arched backs, the center-supported single arch and the ring-supported double arch, are discussed. It is shown that, assuming a maximum permissible rms tolerance of 6 x 10 to the -6th in, the single arch mirror weighs about 50 percent of an equivalent solid mirror up to a diameter of 24 in. The single arch is relatively simple to construct and uses a simple center support. Where a better figure is required, or for larger sizes, the double arch is superior in performance to the single arch. The weight of the double arch will vary from about 50 to under 40 percent of an equivalent conventional mirror as the diameter is increased from 20 to 144 in. Further weight reduction for the double arch is possible through the reduction of the size of the support.

Vukobratovich, D.↗

Gravity deflections of lightweighted mirrors

Two 20-in-diameter lightweight fused-silica mirrors, one having a single arch configuration and the other a double arch configuration, were tested interferometrically at their centers of curvature in both a face-up and face-down support mode. By subtracting the wavefront errors in these two support modes, the gravity deflections were determined in spite of some residual figure error. It is found that the single arch mirror, supported horizontally on three points, has about half the total deflection of the double arch design. The single arch mirror is twice as stiff azimuthally as the double arch, but radially the double arch has four times the stiffness of the single arch. If a more uniform azimuthal support were provided for the double arch, its deflections would be expected to improve significantly.

Anderson, D.↗

Lightweight Electrical Insulation

Hollow plastic spheres expanded and fused together. Hollow, gasfilled plastic spheres piled in mold. Heating in vacuum softens and expands spheres, forcing them together into nearly regular hexagonal close packing. Foam used as lightweight, electrically insulating material in place of solid ceramic, glass, or polymer. Padding to protect against mechanical shocks another application for such dense, regular foam.

Schroeder, J. E.↗

Lightweight Forms for Epoxy/Aramid Ducts

Aluminum mandrels easy to remove. Lightweight aluminum mandrel for shaping epoxy/aramid ducts simplifies and speeds production. In new process, glass-reinforced epoxy/aramid cloth wrapped on aluminum mandrel. Stainless-steel flanges and other hardware fitted on duct and held by simple tooling. Entire assembly placed in oven to cure epoxy. After curing, assembly placed in alkaline bath dissolves aluminum mandrel in about 4 hours. Epoxy/aramid shell ready for use as duct. Aluminum mandrel used to make ducts of various inside diameters up to 6 in. Standard aluminum forms used. Conventional tube-bending equipment produces requisite curves in mandrels.

Mix, E. W.↗

Lightweight, Fire-Resistant Graphite Composites

Aircraft safety improved with interior paneling made of new laminate with good thermophysical properties. Featuring lightweight graphite composite, laminate more heat-and flame-resistant and produces much less smoke in fire than commonly used epoxy-resin-containing laminates. New laminate prepared without epoxy resin. Graphite unidirectional cloth preimpregnated with blend of vinyl polystyrylpyridine and bismaleimide (VPSP-BMI). Either of two types of VPSP-BMI blend used, depending on method of preparation of chemicals and technique used to fabricate panel.

Kourtides, D. A.↗

Ultra lightweight mirror performance at 8 degrees kelvin

Earlier work funded by DARPA, evaluating the optical stability of a 0.5-m ultra-lightweight, frit-bonded, fused silica mirror, is extended from the previous 100 deg K specification down to 8 deg K. The thermal stability is excellent and comparable to that for conventional fusion and solid mirrors. The total mirror change of 0.10 lambda rms (lambda = 0.6328 microns) meets the needs of most IR systems. Thermal elastic quilting is excellent (0.008 lambda). Ames Research Center and Kodak data evaluations, done independently, are in very good agreement.

Crowe, D. A.↗

Grips for Lightweight Tensile Specimens

Set of grips developed for tensile testing of lightweight composite materials. Double-wedge design substantially increases gripping force and reduces slippage. Specimen held by grips made of hardened wedges. Assembly screwed into load cell in tensile-testing machine.

Witte, William G., Jr.↗

Lightweight sidewalls for aircraft interior noise control

A theoretical and experimental study was performed to devise lightweight sidewalls for turboprop aircraft. Seven concepts for new sidewalls were analyzed and tested for noise reduction using flat panels of 1.2 m x 1.8 m (4 ft x 6 ft), some of which were aircraft-type constructions and some of which were simpler, easier-to-construct panels to test the functioning of an acoustic principle. Aircraft-application sidewalls were then conceived for each of the seven concepts, and were subjectively evaluated for their ability to meet aircraft nonacoustic design requirements. As a result of the above, the following sidewall concepts were recommended for further investigation: a sidewall in which the interior cavity is vented to ceiling and underfloor areas; sidewalls with wall-mounted resonators, one having a conventional trim panel and one a limp one; and a sidewall with a stiff outer wall and a limp trim panel. These sidewalls appear to promise lower weights than conventional sidewalls adjusted to meet similar acoustic requirements, and further development may prove them to be practical.

May, D. N.↗

An Investigation of Energy Transmission Due to Flexural Wave Propagation in Lightweight, Built-Up Structures

A technique to measure flexural structure-borne noise intensity is investigated. Two accelerometers serve as transducers in this cross-spectral technique. The structure-borne sound power is obtained by two different techniques and compared. In the first method, a contour integral of intensity is performed from the values provided by the two-accelerometer intensity technique. In the second method, input power is calculated directly from the output of force and acceleration transducers. A plate and two beams were the subjects of the sound power comparisons. Excitation for the structures was either band-limited white noise or a deterministic signal similar to a swept sine. The two-accelerometer method was found to be sharply limited by near field and transducer spacing limitations. In addition, for the lightweight structures investigated, it was found that the probe inertia can have a significant influence on the power input to the structure. In addition to the experimental investigation of structure-borne sound energy, an extensive study of the point harmonically forced, point-damped beam boundary value problem was performed to gain insight into measurements of this nature. The intensity formulations were also incorporated into the finite element method. Intensity mappings were obtained analytically via finite element modeling of simple structures.

Mickol, John Douglas↗

Lightweight piston

A lightweight piston composed of carbon-carbon composites is presented. The use of carbon-carbon composites over conventional materials, such as aluminum, reduces piston weight and improves thermal efficiency of the internal combustion reciprocation engine. Due to the negligible coefficient of thermal expansion and unique strength at elevated temperatures of carbon-carbon, the piston-to-cylinder wall clearance is so small as to eliminate the necessity for piston rings. Use of the carbon-carbon composite has the effect of reducing the weight of other reciprocating engine components allowing the piston to run at higher speeds and improving specific engine performance.

Taylor, Allan H.↗

Lightweight Video-Camera Head

Compact, lightweight video camera head constructed by remounting lens and charge-coupled-device image detector from small commercial video camera in separate assembly. Useful in robotics, artificial vision, and vision guidance systems. Designed to be mounted on visor of helmet to monitor motions of eyes in experiments on vestibulo-ocular reflexes.

Proctor, David R.↗

Lightweight Helmet For Eye/Balance Studies

Lightweight helmet serves as mounting platform for stimulus and sensor modules in experiments on role of vestibulo-ocular reflex in motion sickness and space-adaptation syndrome. Fitted liner and five inflatable air bladders stabilize helmet with respect to subject's head. Personal bite board attached to chin-bar assembly makes hard palate in subject's mouth serve as final position reference for helmet.

Mcstravick, M. Catherine↗

Lightweight Restraint For Coupling Flanges

End flanges of flexible coupling system restrained against excessive rotation or axial separation by inexpensive, lightweight mechanism based on cables and pulleys. Restraining mechanism adapted to cable, duct, hose, or passageway couplings between vehicles, or to other applications in which angular and positional misalignments must be restricted to moderate specified values. Total misalignment of two end flanges limited to amount of slack available in cable-and-pulley mechanism. When cable taut, further axial separation of flange centers restrained, but small tilts accommodated by running of cable through pulleys.

Whitaker, Willie D.↗

Analysis of the nonvented fill of a 4.96-cubic-meter lightweight liquid hydrogen tank

As part of its development of cryogenic fluid management techniques for spacecraft, the NASA Lewis Research Center Cryogenic Fluid Technology Office (CFTO) is planning to perform ground tests of nonvented fill techniques on a 4.96-cubic-meter lightweight liquid hydrogen tank. This tank is similar in size and shape to the tankage planned for CFTO's COLD-SAT liquid hydrogen flight experiment. The analyses used to select two injection systems are presented for nonvented fills of this tank at design flow rates between 220 and 450 kg/hr. The first system uses multiple nozzles spraying from the top of the tank through the ullage space. This system should be capable of liquid fill levels in excess of 95 percent. The second system injects the liquid through a submerged nozzle and should produce fill levels on the order of 80 percent liquid.

Chato, David J.↗

Lightweight fibrous nickel electrodes for nickel-hydrogen batteries

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art sintered nickel electrodes. Lightweight fibrous materials or plaques are used as conductive supports for the nickel hydroxide active material. These materials are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C, and 2.74C. The electrodes that pass the initial tests are life cycle-tested in a low Earth orbit regime at 80 percent depth of discharge.

Britton, Doris L.↗