Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layup”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

403 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗
NASA NTRSDate not supplied

Development of a Combined Cohesive and Virtual Crack-Closure Technique Approach to Represent R-Curves

Resistance curve (R-curve) effects due to fiber bridging, crack migration, and other blunting mechanisms are common in composite laminates. These mechanisms can dramatically increase the resistance to crack propagation but can be challenging to simulate. Delamination with R-curves can be analyzed using cohesive zone modeling (CZM) or the virtual crack closure technique (VCCT). Large fracture process zones can be simulated with CZM, but they require highly refined meshes. Coarser meshes can be used with VCCT, but this method is only applicable to small fracture process zones with R-curves defined as functions of position. Therefore, a technique with the computational efficiency of VCCT and the natural ability of cohesive elements to represent large fracture process zones is desirable. An approach is proposed that starts as a CZM in which the cohesive traction separation law (TSL) is separated into high-strength (HS) and low-strength (LS) components. The HS part, which is responsible for the mesh requirements of the CZM analysis, is replaced by VCCT. The combined method is evaluated by analyzing the response of double cantilevered beam specimens. Two specimen layup configurations, [0/90/90/0] 3s and [0/90/90/0] 9s , are evaluated. The R-curve response from each configuration is determined and applied to the constitutive properties of models built with CZM and with VCCT. The results and computational efficiency of the CZM, VCCT, and combined approaches are compared. The results are indicative that a combined cohesive/VCCT approach can enable progressive failure analyses to retain the computational efficiency of VCCT with the ability of the cohesive elements to capture R-curve effects.

Virtual Crack-Closure Technique↗
NASA NTRSDate not supplied

Preliminary Experimental Investigation of Multi-Shock Shield Performance Against Meteoritic Other Lithic Projectiles

The protection capabilities of micrometeoroid and orbital debris (MMOD) shields are invariably linked to the physical properties of the impactor. Regardless of the shield type, or bumper material employed, the general principles of purposefully designed multi-walled MMOD protection relies on the ability to disrupt, shock, melt, and/or vaporize the projectile before it interacts with a critical spacecraft component. Here, we begin to study the influence of projectile heterogeneity on the performance of multi-shock shields by conducting hypervelocity impact tests using meteorite and a variety of other rock-like (i.e., lithic) materials. Testing was conducted using a .17 caliber two-stage light-gas gun, launching cylindrical lithic projectiles between 5.66 and 7.06 km/s. Shield layups included three layers of Nextel and one layer of graphite composite as a rear wall, with each layer having a 35 mm standoff. After testing a comparison of rear wall and witness plate damage was made to separate tests conducted using spherical Al projectiles of similar mass. It was observed that the more heterogenous meteorite projectile gave rise to notably more damage to the witness plate than an Al projectile of equivalent mass, while the other, more homogeneous lithic projectiles, did not.

meteorite↗
NASA NTRSDate not supplied

Structural Sizing of a Tow-Steered Truss-Braced Wing Box Test Article

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, the design of a tow-steered truss-braced wing test article called the Structural Wing Experiment Evaluating Truss-bracing 15-ft concept (SWEET-15) is discussed. The SWEET-15 test article is scaled to 18.6% of the span length and chord width of a full-scale vehicle. The test article is designed to withstand +2.5-g (positive limit) and -1.0-g (negative limit) maneuvering loads with a factor of safety of 1.5 under strength and buckling constraints. Design studies were performed using commercial finite element analysis and optimization software in conjunction with a tow-steering modeling tool called ATSCOOL (Automated Tool for Steered COmposite Optimizable Laminates) developed at NASA Langley Research center. A 6.4% weight reduction in the upper cover panels was achieved using a tow-steered layup configuration.

Structural Optimization↗
NASA NTRSDate not supplied

Structural Sizing of a Tow-Steered Truss-Braced Wing Box Test Article

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, the design of a tow-steered truss-braced wing test article called the Structural Wing Experiment Evaluating Truss-bracing 15-ft concept (SWEET-15) is discussed. The SWEET-15 test article is scaled to 18.6% of the span length and chord width of a full-scale vehicle. The test article is designed to withstand +2.5-g (positive limit) and -1.0-g (negative limit) maneuvering loads with a factor of safety of 1.5 under strength and buckling constraints. Design studies were performed using commercial finite element analysis and optimization software in conjunction with a tow-steering modeling tool called ATSCOOL (Automated Tool for Steered COmposite Optimizable Laminates) developed at NASA Langley Research center. A 6.4% weight reduction in the upper cover panels was achieved using a tow-steered layup configuration.

Composites↗
DOE OSTI2021

A Multiscale Modeling Approach to Cryocompressed Hydrogen Storage Pressure Vessels – Part II: Constitutive Modeling and Finite Element Analysis

Subjected to thermomechanical cycling, composite cryogenic hydrogen (H2) storage pressure vessels experience high stresses in the carbon fiber (CF)/epoxy overwrap which can lead to vessel failure due to a combination of degradation mechanisms such as matrix cracking, fiber/matrix debonding, delamination, and fiber rupture. The present paper is the second part of a set of two articles on this subject that addresses analysis and design of these pressure vessels. Predictive finite element (FE) modeling capabilities have been used to support a material acceptance process that aims at providing guidance to evaluate specialty resins, vessel liner options, and CF composites through thermomechanical testing. We have applied a multiscale modeling approach recently developed (B.N. Nguyen et al., International Journal of Hydrogen Energy, 2019, https://doi.org/10.1016/j.ijhydene.2019.09.200) to perform three-dimensional (3D) FE analysis and design of a cryo-compressed H2 storage pressure vessel for its operation in a large temperature range from room to cryogenic temperatures. The developed approach termed the micro-meso-macro approach determines the laminar stresses in different layers of the vessel in addition to constituent (i.e., fiber and matrix) stresses that are important to the design of the composite overwrap for its layup and material combination to reduce the risk of vessel failure.

Nguyen, Ba Nghiep↗
DOE OSTI2023

3D Printed Carbon Fiber Reinforced Carbon: An energy efficient alternative to graphite EFAS tooling

Carbon fiber preforms are printed in a Quasi-Isotropic layup, where the fibers are aligned to the X and Y axes, and ±45° in plane. Thermal and electrical conductivity values along the fiber axes are comparable to graphite but are extremely low through the Z axis. Low conductivity (high resistivity) in the axis of current flow enables more efficient Joule heating.

36 MATERIALS SCIENCE↗