Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Design of a three-layer antireflection coating for high efficiency indium phosphide solar cells using a chemical oxide as first layer

It is well known that the behavior of III-V compound based solar cells is largely controlled by their surface, since the majority of light generated carriers (63% for GaAs and 79% for InP) are created within 0.2 mu m of the surface of the illuminated cell. Consequently, the always observed high surface recombination velocity (SRV) on these cells is a serious limiting factor for their high efficiency performance, especially for those with p-n junction made by either thermal diffusion or ion implantation. A good surface passivation layer, ideally a grown oxide as opposed to a deposited one, will cause a significant reduction in the SRV without adding interface problems, thus improving the performance of III-V compound based solar cells. Another significant benefit to the overall performance of the solar cells can be achieved by a substantial reduction of their large surface optical reflection by the use of a well designed antireflection (AR) coating. In this paper, we demonstrate the effectiveness of using a chemically grown thermally and chemically stable oxide, not only for surface passivation but also as an integral part of a 3-layer AR coating for thermally diffused p+n InP solar cells. A phosphorus-rich interfacial oxide, In(PO3)3, is grown at the surface of the p+ emitter using an etchant based on HNO3, o-H3PO4 and H2O2. This oxide has the unique properties of passivating the surface as well as serving as an efficient antireflective layer yielding a measured record high AMO open-circuit voltage of 890.3 mV on a thermally diffused InP(Cd,S) solar cell. Unlike conventional single layer AR coatings such as ZnS, Sb2O3, SiO or double layer AR coatings such as ZnS/MgF2 deposited by e-beam or resistive evaporation, this oxide preserves the stoichiometry of the InP surface. We show that it is possible to design a three-layer AR coating for a thermally diffused InP solar cell using the In(PO3)3 grown oxide as the first layer and Al2O3 and MgF2 as the second and third layers respectively, so as to yield an overall theoretical reflectance of less than 2%. Since chemical oxides are readily grown on III-V semiconductors materials, the technique of using the grown oxide layer to both passivate the surface as well as serve as the first of a multilayer AR coating should work well for all III-V compound-based solar cells.

Moulot, Jacques↗
DOE OSTI2026

Ionic Interdiffusion at Cathode|Solid-Electrolyte Interface: A Machine Learning–Assisted Multiscale Investigation and Mitigation Strategies

Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.

Ncube, Musawenkosi K.↗
NASA NTRS2016

TEM Analysis of Interfaces in Diffusion-Bonded Silicon Carbide Ceramics Joined Using Metallic Interlayers

Silicon Carbide (SiC) is a promising material for thermo-structural applications due to its excellent high-temperature mechanical properties, oxidation resistance, and thermal stability. However, joining and integration technologies are indispensable for this material in order to fabricate large size and complex shape components with desired functionalities. Although diffusion bonding techniques using metallic interlayers have been commonly utilized to bond various SiC ceramics, detailed microstructural observation by Transmission Electron Microscopy (TEM) of the bonded area has not been carried out due to difficulty in preparing TEM samples. In this study, we tried to prepare TEM samples from joints of diffusion bonded SiC ceramics by Focused Ion Beam (FIB) system and carefully investigated the interfacial microstructure by TEM analysis. The samples used in this study were SiC fiber bonded ceramics (SA-Tyrannohex: SA-THX) diffusion bonded with metallic interlayers such as Ti, TiMo, and Mo-B. In this presentation, the result of microstructural analysis obtained by TEM observations and the influence of metallic interlayers and fiber orientation of SA-THX on the joint microstructure will be discussed.

Silicon Carbide↗
NASA NTRS2017

TEM Analysis of Diffusion-Bonded Silicon Carbide Ceramics Joined Using Metallic Interlayers

Silicon Carbide (SiC) is a promising material for thermostructural applications due to its excellent high-temperature mechanical properties, oxidation resistance, and thermal stability. However, joining and integration technologies are indispensable for this material in order to fabricate large size and complex shape components with desired functionalities. Although diffusion bonding techniques using metallic interlayers have been commonly utilized to bond various SiC ceramics, detailed microstructural observation by Transmission Electron Microscopy (TEM) of the bonded area has not been carried out due to difficulty in preparing TEM samples. In this study, we tried to prepare TEM samples from joints of diffusion bonded SiC ceramics by Focused Ion Beam (FIB) system and carefully investigated the interfacial microstructure by TEM analysis. The samples used in this study were SiC fiber bonded ceramics (SA-Tyrannohex: SA-THX) diffusion bonded with metallic interlayers such as Ti, TiMo, Mo-B and TiCu. In this presentation, we report the microstructure of diffusion bonded SA-THX mainly with TiCu interlayers obtained by TEM observations, and the influence of metallic interlayers on the joint microstructure and microhardness will be discussed.

Ceramics↗
NASA NTRS1995

Design of a Three-Layer Antireflection Coating for High Efficiency Indium Phosphide Solar Cells Using a Chemical Oxide as First Layer

It is well known that the behavior of III-V compound based solar cells is largely controlled by their surface, since the majority of light generated carriers (63% for GaAs and 79% for InP) are created within 0.2 microns of the illuminated surface of the cell. Consequently, the always observed high surface recombination velocity (SRV) on these cells is a serious limiting factor for their high efficiency performance, especially for those with the p-n junction made by either thermal diffusion or ion implantation. A good surface passivation layer, ideally, a grown oxide as opposed to a deposited one, will cause a significant reduction in the SRV without adding interface problems, thus improving the performance of III-V compound based solar cells. Another significant benefit to the overall performance of the solar cells can be achieved by a substantial reduction of their large surface optical reflection by the use of a well designed antireflection (AR) coating. In this paper, we demonstrate the effectiveness of using a chemically grown, thermally and chemically stable oxide, not only for surface passivation but also as an integral part of a 3- layer AR coating for thermally diffused p(+)n InP solar cells. A phosphorus-rich interfacial oxide, In(PO3)3, is grown at the surface of the p(+) emitter using an etchant based on HNO3, o-H3PO4 and H2O2. This oxide has the unique properties of passivating the surface as well as serving as a fairly efficient antireflective layer yielding a measured record high AM0, 25 C, open-circuit voltage of 890.3 mV on a thermally diffused InP(Cd,S) solar cell. Unlike conventional single layer AR coatings such as ZnS, Sb2O3, SiO or double layer AR coatings such as ZnS/MgF2 deposited by e-beam or resistive evaporation, this oxide preserves the stoichiometry of the InP surface. We show that it is possible to design a three-layer AR coating for a thermally diffused InP solar cell using the In(PO3)3 grown oxide as the first layer and Al2O3, MgF2 or ZnS, MgF2 as the second and third layers respectively, so as to yield an overall theoretical reflectance of less than 2%. Since chemical oxides are readily grown on III-V semiconductor materials, the technique of using the grown oxide layer to both passivate the surface as well as serve as the first of a multilayer AR coating, should work well for essentially all III-V compound-based solar cells.

Moulot, Jacques↗
DOE OSTI2022

Assessment of antimicrobial activity of melittin encapsulated in bicontinuous microemulsions prepared using renewable oils

Abstract The objective of this study is to demonstrate that melittin, a well‐studied antimicrobial peptide (AMP), can be solubilized in an active form in bicontinuous microemulsions (BMEs) that employ biocompatible oils. The systems investigated consisted of Winsor‐III and ‐IV BME phases composed of Water/Aerosol‐OT (AOT)/Polysorbate 85/isopropyl myristate and a Winsor‐IV BME employing Polysorbate 80 and limonene. We found that melittin resided in an α‐helix‐rich configuration and was in an apolar environment for the AOT/Polysorbate 85 Winsor‐III system, suggesting that melittin interacted with the surfactant monolayer and was in an active conformation. An apolar environment was also detected for melittin in the two Winsor‐IV systems, but to a lesser extent than the Winsor‐III system. Small‐angle X‐ray scattering analysis indicated that melittin at a concentration of 1.0 g/L aq in the aqueous subphase of the Winsor‐IV systems led to the greatest impact on the BME structure (e.g., decrease of quasi‐periodic repeat distance and correlation length and induction of interfacial fluidity). The antimicrobial activity of the Polysorbate 80 Winsor‐IV system was evaluated against several bacteria prominent in chronic wounds and surgical site infections (SSIs). Melittin‐free BMEs inhibited the growth of all tested bacteria due to its oil, limonene, while the inclusion of 1.0 g/L aq of melittin in the BMEs enhanced the activity against several bacteria. A further increase of melittin concentration in the BMEs had no further enhancement. These results demonstrate the potential utility of BMEs as a delivery platform for AMPs and other hydrophilic and lipophilic drugs to inhibit antibiotic‐resistant microorganisms in chronic wounds and SSIs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Enhancing Oxygen Evolution Reaction and Stability in Proton-Conducting Solid Oxide Electrolysis Cells (p-SOECs) via a Porous Gadolinium-Doped Ceria Interlayer

Proton-conducting solid oxide electrolysis cells (p-SOECs) offer a promising pathway for intermediate temperature (400-600 °C) hydrogen production. However, they still face critical challenges related to sluggish oxygen evolution reaction (OER) kinetics and low Faradaic efficiencies. Here, in this work, we demonstrate that introducing a thin (~0.8 µm) porous Gd 0.1 Ce 0.9 O 1.95 (GDC) interlayer between a BaCo 0.8 Zr 0.1 Zn 0.1 O 3-δ (BCZZ) oxygen electrode and electrolyte significantly enhances p-SOEC performance. The GDC interlayer reduces polarization resistance by 48% (0.54 to 0.28 O cm 2 ) and increases Faradaic efficiency from 63% to 81% at -0.8 A/cm 2 and 600 °C. GDC interlayer p-SOECs display elevated effective H 2 current densities compared to control p-SOECs and reach up to -1.22 A/cm 2 at 1.3 V. Mechanistic studies on the interactions between GDC and BCZZ reveal that GDC intrinsically promotes OER kinetics by significantly reducing the polarization activation energy (Ea p ), dropping from 1.45 to 1.22 eV for full p-SOECs and 0.98 to 0.76 eV for symmetric cells. This promotional effect is localized in the electrochemically active region near the electrolyte interface. Durability testing for over 1500 hours under 50% H 2 O conditions indicates that the GDC interlayer also improves long-term stability, with a degradation rate 53% lower than control p-SOECs. By pinpointing the interfacial region where GDC exerts its promotional effect, highlighting its role in enhancing OER kinetics, and establishing interlayer engineering as a powerful technique, this work provides a unified pathway to simultaneously improve p-SOEC activity, Faradaic efficiency, and durability.

08 - HYDROGEN↗
DOE OSTI2021

A closer look at corrosion of steel reinforcement bars in concrete using 3D neutron and X-ray computed tomography

Corrosion of reinforcing bars constitutes the largest threat to the durability of concrete structures. Thus, several studies have investigated the nature of the corrosion products, most using post-mortem analyses. However, corrosion products evolve when in contact with oxygen, hindering result interpretation. This work presents instead a state-of-the-art, non-destructive 3D method for the assessment of corrosion of embedded reinforcements. Multimodal neutron and X-ray tomography was used to observe, non-destructively, the characteristics of the corrosion products in two concrete samples, with the aim of investigating possible benefits of the use of this technique for reinforced concrete structures. One sample was naturally corroded, extracted from an 81-year-old bridge, the other was corroded via the galvanostatic method, resulting in corrosion-induced cracks. Quantitative and qualitative data was acquired, including the iron-to-rust volumetric ratio in macroscopic interfacial voids and the thickness of the corrosion layer at the steel concrete interface. The iron-to-rust volumetric ratio corresponded to large, soluble, corrosion products, forming in environments with low availability of oxygen for both samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural, Corrosion and Mechanical Characterization of Friction-Stir Welded Joints Between Aluminum and Magnesium Alloys

Friction Stir Welding (FSW) of Aluminum-Magnesium (Al-Mg) alloys has garnered increasing attention due to its wide-ranging applications in the automotive and aerospace industries. The microstructural, corrosion, and mechanical properties of FSW Al-Mg welds under selected conditions are critical factors that must be well-investigated to ensure their durability and performance. In this study, electrochemical tests, including Open Circuit Potential (OCP), Linear Polarization Resistance (LPR), Potentiodynamic Polarization Scan (PD), and Electrochemical Impedance Spectroscopy (EIS), have been used to analyze the corrosion resistance of these welds, along with weight loss measurements through cyclic corrosion testing (CCT) and surface evolution via SEM over an 8-week period. Mechanical properties are evaluated through microindentation, nanoindentation, fatigue, and lap-shear tests. The results of the electrochemical tests reveal that the corrosion properties of the center weld zone differ from those of the two base alloys. Indentation tests indicate that the weld zone behaves differently from the base alloys. Surprisingly, the lap shear strength did not decrease significantly even after 8 weeks of cyclic corrosion testing, indicating that the joint prevented any ingress of the electrolyte. Fatigue testing showed that applying an adhesive between the Al and Mg joint improved the fatigue life to some extent, although the corrosion resistance reduced due to the discontinuous bonding of the adhesive layer. Overall, these findings highlight the importance of investigating the corrosion and mechanical properties of FSW Al-Mg welds and provide valuable insights for future modeling works.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Synergistic Coupling Effect of Electronic Conductivity and Interphase Compatibility on High-Voltage Na 3 V 2 (PO 4 ) 2 F 3 Cathodes

Na 3 V 2 (PO 4 ) 2 F 3 (NVPF) has been considered an up-and-coming cathode material candidate for sodium (Na) ion batteries in light of its high specific capacity and working voltage. However, an erratic cathode/electrolyte interface layer is inevitably formed, accompanied by continuous electrolyte decomposition on the NVPF surface, when the voltage exceeds 4.2 V vs Na + /Na. Herein, the interphase features of NVPF are obviously enhanced owing to the ameliorated electronic conductivity obtained by combining it with carbon nanotubes (CNT). The NVPF with 3 wt % CNT (NVPF@3% CNT) reduces the Na + diffusion kinetic energy barrier and electron transport resistance. Furthermore, the conducting network formed by CNT with sturdy structure strength can promptly accommodate the volumetric changes during sequential Na + extraction/insertion and thus effectively improve the long-term cyclic performance of NVPF/hard carbon full cells. The initial discharge capacity approaches 105 mA h g –1 at 0.5C, and it retains 94% capacity retention after 200 cycles at the temperature of –10 °C. The cathode/electrolyte interphase characterization results further demonstrate that the interphase layer on the NVPF@3% CNT cathode is thinner and more compact compared with pristine samples. Here, this research provides a competitive strategy to facilitate the interfacial compatibility between the NVPF and electrolytes and accelerate the commercialization of high-performance Na-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Laser additive manufacturing for infrastructure repair: A case study of a deteriorated steel bridge beam

As our transportation infrastructure ages, its deterioration is becoming a growing concern. Rapid and effective methods for repair can reduce the need for time-and cost-intensive replacement of structures such as roadway bridges. In this work, laser-based additive manufacturing (AM) was developed for the re-pair of damaged beams in steel bridges. A corroded structural beam of low-carbon A36 steel was selected for this case study and 316L stainless steel was used for repair due to its excellent mechanical properties and corrosion resistance. Simulated repair experiments were performed on specimens extracted from the beam, and prepared with various groove shapes (Rectangular, Trapezoidal, and U-shaped). More in-depth parametric and microstructural studies were carried out with a series of U-shaped specimens repaired with the linear laser input energy varied from 19.5 to 30.0 J mm -1 . The tensile properties of the repaired specimens and interface structures were also investigated in detail. It was found that the repaired specimens had a slightly higher tensile strength despite a reduction in tensile elongation compared to the A36 steel base metal. The influence of interfacial microstructure and heterogeneity on the mechanical proper-ties of the repaired specimens was discussed. Furthermore, our work suggests the promising potential to employ AM for structural repair and provides fundamental insights into processing-structure-property relationships in laser AM-repaired materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Influence of zwitterionic amphiphilic copolymers on heterogeneous gypsum formation: A promising approach for scaling resistance

Here, this study aims to investigate the influence of zwitterionic amphiphilic copolymers (ZACs) in the nucleation and growth of heterogeneous CaSO4 at the zwitterion-water interface, which is crucial for the prevention of mineral scaling and consequent downtime or suboptimal performance in industries like membrane desalination, heat exchangers, and pipeline transportation. In situ grazing incidence small angle X-ray Scattering (GISAXS), and quartz crystal microbalance with dissipation (QCM-D) techniques were used to analyze the evolution of CaSO 4 particles on two new ZAC coatings: poly-(trifluoroethyl methacrylate-random-sulfobetaine methacrylate) (PTFEMA-r-SBMA, or PT:SBMA) and poly(trifluoroethyl methacrylate-random-2-methacryloyloxyethyl phosphorylcholine) (PTFEMA-r-MPC, or PT:MPC). The results showed that PT:MPC coatings promoted nucleation but inhibited crystal growth, resulting in slower overall reaction kinetics on PT:MPC coatings compared to PT:SBMA coatings. Interfacial interactions involving the substrates, sulfate minerals, and ions were examined, revealing that calcium ion adsorption, primarily governed by electrostatic attraction, played a crucial role in the nucleation and growth processes on both ZAC coatings. The crystal characterization revealed a phase transition from bassanite to gypsum on both ZAC coatings, suggesting that these zwitterionic materials can influence the mineral phase of heterogeneously formed CaSO 4 crystals. These findings enhance our understanding of the fundamental mechanisms underlying heterogeneous CaSO 4 scaling in the presence of zwitterionic materials.

42 ENGINEERING↗
DOE OSTI2022

Mapping hidden space-charge distributions across crystalline metal oxide/group IV semiconductor interfaces

The electronic structures of semiconducting heterojunctions are critically dependent on composition including the presence and concentrations of dopants, both intended and unintended. Dopant profiles in the interfacial region can have major effects on band energies which in turn drive transport properties. Here, in this study, we use core-level photoelectron line shapes excited with hard x rays to extract information about electric fields resulting from internal charge transfer in epitaxial La 0.03 Sr 0.97 Zr x Ti 1–x O 3 /Ge(001) (0.1≤x≤0.7) heterostructures. Experiments were carried out for heterojunctions involving both n- and p-type Ge substrates. These heterojunctions were not amenable to electronic characterization of all regions by transport measurements because the doped substrates act as electrical shunts, precluding probing the more resistive films and masking interface conductivity. However, the core-level line shapes were found to be a rich source of information on built-in potentials that exist throughout the heterostructure, and yielded valuable insight into the impact of band bending on band alignment at the buried interfaces. The electronic effects expected for Ge with uniform n- and p-type doping are eclipsed by those of unintended oxygen dopants in the Ge near the interface. This study illustrates the power of hard x-ray photoemission spectroscopy and related modeling to determine electronic structure in material systems for which insight from traditional transport measurements is limited.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Kinetics and transport at AMTEC electrodes. II - Temperature dependence of the interfacial impedance of Na(g)/porous Mo/Na-Beta-double prime alumina

The exchange current, transfer coefficient, mass-transport parameters, and electrode capacitance at the Na(g)/porous Mo/Na-Beta-double prime alumina solid electrolyte (BASE) phase boundary have been evaluated from 740 to 1220 K. The transfer coefficient exhibits a value close to 0.5 and the exchange current is dominated by collision frequency, with no significant activation energy. Since the porous Mp-electrode adopts a fairly regular microstructure on the BASE surface, the magnitude of the exchange current of mature electrodes directly depends on the actual contact zone of the porous metal film with the BASE ceramic, and decreases slightly as grain growth occurs. The exchange currents and the mass-transport parameters derived for very porous, thin Mo electrodes indicate that the charge-transfer reaction occurs at a small fraction of the interface. High-frequency limiting capacitance and resistance values due to the interface show potential dependence and a value on the order of 1 F/sq m and 0.1-1.0 Ohm-sq cm.

Williams, R. M.↗
DOE OSTI2020

Emerging Magnetic Interactions in van der Waals Heterostructures

Vertical van der Waals (vdWs) heterostructures based on layered materials are attracting interest as a new class of quantum materials, where interfacial charge-transfer coupling can give rise to fascinating strongly correlated phenomena. Transition metal chalcogenides are a particularly exciting material family, including ferromagnetic semiconductors, multiferroics, and superconductors. Here, we report the growth of an organic–inorganic heterostructure by intercalating molecular electron donating bis(ethylenedithio)tetrathiafulvalene into (Li,Fe)OHFeSe, a layered material in which the superconducting ground state results from the intercalation of hydroxide layer. Molecular intercalation in this heterostructure induces a transformation from a paramagnetic to spin-glass-like state that is sensitive to the stoichiometry of molecular donor and an applied magnetic field. Besides, electron-donating molecules reduce the electrical resistivity in the heterostructure and modify its response to laser illumination. In conclusion, this hybrid heterostructure provides a promising platform to study emerging magnetic and electronic behaviors in strongly correlated layered materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

First-principles study of Al/Al 3 Ni interfaces

Al-Ni alloys have shown promise for high-temperature applications due to the strengthening of Al 3 Ni fibers resistant to coarsening and spheroidization up to 400°C. While the interface between Al and Al 3 Ni phases affects the coarsening rate of Al 3 Ni at elevated temperatures, its characteristics are largely unknown to date. Here, we have constructed various supercells to model this interface and performed a first-principles study based on density functional theory (DFT). We have considered three groups of Al/Al 3 Ni interfaces: experimentally reported orientation relationships from the solidification studies, crystallographically similar Fe-Fe 3 C pearlite interfaces, and the family of low-index (100) termination planes. We have analyzed the correlation between the DFT Al/Al 3 Ni interfacial energies and characteristic features, e.g., excess free volume and the number of broken bonds. We outline the further experimental and computational analysis required to improve the interface modeling of Al/Al 3 Ni.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evidence of antiferromagnetism in ultrathin metallic (111)-oriented LaNiO 3 films

Antiferromagnets with exotic spin textures promise low-power spintronic devices with extremely high operating frequencies and resistance to external perturbations. In particular, the combination of highly tunable correlated electron physics, as in complex oxides, with metallicity and antiferromagnetism is desirable but exceedingly rare. LaNiO 3 , the lone example of a perovskite nickelate which is metallic across all temperatures, has long been a promising candidate, but the antiferromagnetic metallic state has remained elusive. Here, we demonstrate the emergence of this state in ultrathin films of (111)-oriented LaNiO 3 using a combination of polarized neutron reflectometry, low-energy muon spectroscopy and anomalous Hall effect measurements, and density functional theory calculations with a Hubbard U term. Further, we find a highly strained symmetry-breaking interfacial region which may support canting of the AFM moments leading to a vanishingly small net magnetization at the film-substrate interface, providing a convenient route toward control of the Néel order. Evidence of antiferromagnetic metallic behavior in (111)LNO films highlights the role of crystal symmetry in tuning the novel quantum states in complex oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Increasing Multilayer Ceramic Capacitor Lifetime With Bipolar Voltage Cycling

Enhancing the lifetime of multilayer ceramic capacitors (MLCCs) is critical in many aerospace, naval, or electrical grid applications, where device failure could lead to catastrophic consequences. The migration of oxygen vacancies from the ceramic to the electrode interface under constant bias is known to reduce the lifetime of oxide-based MLCCs. Bias cycling presents an opportunity to enhance MLCC lifetime by reducing oxygen vacancy migration. The ideal frequency range is expected to lie between frequencies low enough to avoid self-heating but high enough to avoid interfacial defect formation. However, the impact of low-frequency bipolar voltage cycling (BVC) on MLCC degradation mechanisms has not been well studied. This work investigates the impact of periodic BVC on the degradation of MLCCs through highly accelerated lifetime testing (HALT) on X7R capacitors. HALT tests were conducted at 255 °C and 60 V using different switching frequencies: 0 (dc), 0.1, 2.5, and 10 Hz. BVC was found to improve the lifetime of MLCCs compared to dc test conditions. MLCCs tested at 10-Hz BVC showed a 311% increase in average time to failure compared to the dc case. Impedance spectroscopy shows that BVC decreases the rate of resistance degradation within MLCCs, indicating that oxygen vacancy migration to the electrodes is mitigated. The impedance spectra taken on BVC samples highlight how grain boundaries play a vital role in trapping oxygen vacancies. Periodic cycling causes oxygen vacancies to become trapped at grain boundaries, resulting in oxygen vacancies taking longer to reach the electrode interface and thus increasing MLCC lifetime. This work highlights not only how BVC can be used to increase MLCC lifetime but also how periodically cycling MLCCs could increase lifetime in extreme environments, such as at elevated temperatures and electric fields.

Chuong, Kayla Y.↗