SEARCH · Engineering Papers

Results for “interconnection studies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Non-Solvent Induced Phase Separation Enables Designer Redox Flow Battery Electrodes

Porous carbonaceous electrodes are performance-defining components in redox flow batteries (RFBs), where their properties impact the efficiency, cost, and durability of the system. The overarching challenge is to simultaneously fulfill multiple seemingly contradictory requirements—i.e., high surface area, low pressure drop, and facile mass transport—without sacrificing scalability or manufacturability. Here, non-solvent induced phase separation (NIPS) is proposed as a versatile method to synthesize tunable porous structures suitable for use as RFB electrodes. The variation of the relative concentration of scaffold-forming polyacrylonitrile to pore-forming poly(vinylpyrrolidone) is demonstrated to result in electrodes with distinct microstructure and porosity. Tomographic microscopy, porosimetry, and spectroscopy are used to characterize the 3D structure and surface chemistry. Flow cell studies with two common redox species (i.e., all-vanadium and Fe2+/3+) reveal that the novel electrodes can outperform traditional carbon fiber electrodes. It is posited that the bimodal porous structure, with interconnected large (>50 µm) macrovoids in the through-plane direction and smaller (<5 µm) pores throughout, provides a favorable balance between offsetting traits. Although nascent, the NIPS synthesis approach has the potential to serve as a technology platform for the development of porous electrodes specifically designed to enable electrochemical flow technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Stable water splitting using photoelectrodes with a cryogelated overlayer

Hydrogen production techniques based on solar-water splitting have emerged as carbon-free energy systems. Many researchers have developed highly efficient thin-film photoelectrochemical (PEC) devices made of low-cost and earth-abundant materials. However, solar water splitting systems suffer from short lifetimes due to catalyst instability that is attributed to both chemical dissolution and mechanical stress produced by hydrogen bubbles. A recent study found that the nanoporous hydrogel could prevent the structural degradation of the PEC devices. In this study, we investigate the protection mechanism of the hydrogel-based overlayer by engineering its porous structure using the cryogelation technique. Tests for cryogel overlayers with varied pore structures, such as disconnected micropores, interconnected micropores, and surface macropores, reveal that the hydrogen gas trapped in the cryogel protector reduce shear stress at the catalyst surface by providing bubble nucleation sites. The cryogelated overlayer effectively preserves the uniformly distributed platinum catalyst particles on the device surface for over 200 h. Our finding can help establish semi-permanent photoelectrochemical devices to realize a carbon-free society.

42 ENGINEERING↗

DOE OSTI2025

Real Space Imaging of Field-Driven Decision-Making in Nanomagnetic Galton Boards

A possible spintronic route to hardware implementation for decision-making involves injecting a domain wall into a bifurcated magnetic nanostrip resembling a Y-shaped junction. A decision is made when the domain wall chooses a particular path through the bifurcation. Recently, it was shown that a structure like a nanomagnetic Galton board, which is essentially an array of interconnected Y-shaped junctions, produces outcomes that are stochastic and therefore relevant to artificial neural networks. However, the exact mechanism leading to the robust nature of randomness is unknown. Here, in this study, we directly image the decision-making process in nanomagnetic Galton boards using Lorentz transmission electron microscopy. We identify that the stochasticity in nanomagnetic Galton boards arises as a culmination of (1) the topology of the injected domain wall, (2) dissimilarly sized vertices, and (3) the strength of the applied field. Our results pave the way to a detailed understanding of stochasticity in nanomagnetic networks.

lorentz microscopy↗

DOE OSTI2021

Performance Evaluation of Adaptive Routing on Dragonfly-based Production Systems

Performance of applications in production environments can he sensitive to network congestion. Cray Aries supports adaptively routing each network packet independently based on the load or congestion encountered as a packet traverses the network. Software can dictate different routing policies, adjusting between minimal and non-minimal bias, for each posted message. We have extensively evaluated the sensitivity of the routing bias selection on application performance as well as whole system performance in both production and controlled conditions. We show that the default routing bias used in Aries-based systems is often sub-optimal and that using a higher bias towards minimal routes will not only reduce the congestion effects on the application but also will decrease the overall congestion on the network. This routing scheme results in not only improved mean performance (by up to 12%) of most production applications hut also reduced run-to-run variability. Our study prompted the two supercomputing facilities (ALCF and NERSC) to change the default routing mode on their Aries-based systems. We present the substantial improvement measured in the overall congestion management and interconnect performance in production after making this change.

Chunduri, Sudheer↗

DOE OSTI2020

Activation Energy for End-of-Life Solder Bond Degradation: Thermal Cycling of Field-Aged PV Modules

The longevity of solar photovoltaic modules depends on the durability and reliability of their components, one of which is the solder bonds in interconnect ribbons. The solder joints experience stresses from thermal cycling and constant elevated temperatures (40 °C-70 °C) in regular field operation leading to thermo-mechanical fatigue and intermetallic compound formation. To study the end-of-life wear-out mechanisms and to obtain activation energy of solder bond degradation, here two field-aged modules from Arizona-a 21-year-old Solarex MSX60 module (with Sn62Pb36Ag2 at the solder joints) and an 18-year-old Siemens M55 module (with Sn60Pb40 at the solder joints)-underwent 800 and 400 modified thermal cycles, respectively. Using three heating blankets, each module had three temperature zones maintained at 85, 95, and 105 °C during the 15-min hot dwell time of the thermal cycle. Cell-level series resistance data obtained from three temperature zones enabled the calculation of activation energy for solder bond degradation for the MSX60 and the M55 modules to be 0.12 eV and 0.35 eV, respectively. From each temperature zone in both modules, busbar-solder samples were obtained, imaged through SEM, and analyzed with energy-dispersive X-ray spectroscopy. In the MSX60 module with traces of Ag in the solder material, phase segregation and growth were primarily observed at high temperatures. For M55 modules without Ag in the solder material, major phase segregation was observed in all temperature zones. The IMC thickness for both modules increased with increasing module temperature. The beneficial effect of Ag in solder material on mitigating solder bond degradation is presented.

14 SOLAR ENERGY↗

DOE OSTI2022

Forming Interphase Microgrids in Distribution Systems Using Cooperative Inverters

Interphase-microgrids formed by three islanded single-phase feeders in distribution systems are proposed in this paper. Loss of utility caused by natural and human-made disasters may isolate each residential subdivision from the utility. In this case, the household loads are supplied by distributed generation (DG) units which may not be enough to meet the load demand. This can lead to deviations in voltage and frequency, and the deviations may vary for each phase. The proposed solution is to form an interphase-microgrid by seamlessly interconnecting the islanded single-phase feeders. This interphase-microgrid can effectively balance the load demands and DG generation in distribution systems after losing the utility supply. This paper presents different case studies to demonstrate the viability of forming interphase-microgrids for residential distribution systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS1973

Software approach to automatic patching of analog computer

The Automatic Patching Verification program (APV) is described which provides the hybrid computer programmer with a convenient method of performing a static check of the analog portion of his study. The static check insures that the program is patched as specified, and that the computing components being used are operating correctly. The APV language the programmer uses to specify his conditions and interconnections is similar to the FORTRAN language in syntax. The APV control program reads APV source program statements from an assigned input device. Each source program statement is processed immediately after it is read. A statement may select an analog console, set an analog mode, set a potentiometer or DAC, or read from the analog console and perform a test. Statements are read and processed sequentially. If an error condition is detected, an output occurs on an assigned output device. When an end statement is read, the test is terminated.

Source record↗

NASA NTRS1976

On the occurrence of sympathetic flares

Random-coincidence formulas are applied to the data used in previous studies of alleged sympathetic flares to determine whether statistical evidence on the occurrence of such flares can be found for specific physically connected pairs of active regions. Only those active regions that are interconnected by magnetic loops in soft X-rays on Skylab photographs are considered to be physically connected. All pairs of flaring active regions (both interconnected and otherwise) observed on the sun during the Skylab flight are also evaluated. The only positive result is obtained with statistical confidence of 3.4 sigmas for pairs of active regions separated by no more than 30 deg. The occurrence of short time intervals between flares is shown to be increased for such active-region pairs, but the pattern of time intervals is found not to correspond with any propagation mode of a triggering agent in the solar atmosphere. It is suggested that some subphotospheric synchronization of activity in nearby plages and sunspot groups could increase the number of short time intervals between flares at different locations without any actual influence of one 'sympathetic' flare upon another, leading to the concept of 'sympathetic active regions' instead of 'sympathetic flares'.

Fritzova-Svestkova, L.↗

NASA NTRS1979

Array Automated Assembly Task for the Low Cost Solar Array Project, Phase 2

Using silk screened evaporated and sputtered Al as the metal source, the formation of Al back surface fields was studied. The most satisfactory results were those obtained with the sputtered A1 and in which open circuit voltages (V sub oc) of 0.585 v (12 ohm cm FZ silicon) were achieved. The ultrasonic interconnect process is discussed. The process is shown to be satisfactory, but increased pull-strength may be obtained if some form of sintering is carried out on the metallized contacts. Plasma etching is shown to be feasible as a replacement for wet chemical cleaning prior to diffusion. Initial results on cells prepared by using electroless Pd/Ni plus either electroplated Ag or Cu show slightly poor performance than cells with the baseline evaporated Ti/Pd/Ag system. A mask designed for the 1.6 x 7.0 cm and 2.0 x 7.0 cm cells is described. This mask has a lower area coverage and total lower resistive loss than the previous mask design. It is also shown that the cell width should not exceed 2.0 - 3.0 cm for optimum efficiency.

Campbell, R. B.↗

NASA NTRS2001

A Parallel Multigrid Solver for Viscous Flows on Anisotropic Structured Grids

This paper presents an efficient parallel multigrid solver for speeding up the computation of a 3-D model that treats the flow of a viscous fluid over a flat plate. The main interest of this simulation lies in exhibiting some basic difficulties that prevent optimal multigrid efficiencies from being achieved. As the computing platform, we have used Coral, a Beowulf-class system based on Intel Pentium processors and equipped with GigaNet cLAN and switched Fast Ethernet networks. Our study not only examines the scalability of the solver but also includes a performance evaluation of Coral where the investigated solver has been used to compare several of its design choices, namely, the interconnection network (GigaNet versus switched Fast-Ethernet) and the node configuration (dual nodes versus single nodes). As a reference, the performance results have been compared with those obtained with the NAS-MG benchmark.

Prieto, Manuel↗

NASA NTRS1977

Follow-On Studies for Design Definition of a Lift/Cruise Fan Technology V/STOL Airplane, Volume 1

A three engine, three fan V/STOL airplane was designed for use as a Research Technology Airplane in proof-of-concept of a candidate configuration for use as a Navy multimission airplane. Use of mechanically interconnected variable pitch fans is made to accommodate power transfer for flight control in hover and to provide flight capability in the event of a single engine failure. The airplane is a modification of a T-39A transport. Design definition is provided for high risk propulsion components and a development test program is defined.

Source record↗

DOE OSTI2020

Enhanced dynamic equivalent identification method of large-scale power systems using multiple events

The increasing complexity of the interconnected power system makes high-fidelity dynamic simulation models computationally more intensive. To improve computation efficiency, model reduction techniques have been investigated to only preserve the dynamics in a limited area of interest (study area), while deriving equivalent representation for the external area. For this purpose, a measurement-based reduction approach using system identification techniques has been previously proposed. Accordingly, external areas are represented by dynamic equivalent loads using transfer function estimation. In this paper, in order to enhance the accuracy of the reduced model in preserving dynamics of the study area, multiple “grid” events of different types and at different locations are considered for identifying the parameters of the equivalent loads. Additionally, case studies are carried out in the NPCC 140-bus system. Comparisons are made between multiple events training and single event training, highlighting the advantages of the proposed method in providing a better representation of the grid dynamics under different operating conditions.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

Open-channel metal particle superlattices

Although tremendous advances have been made in preparing porous crystals from molecular precursors, there are no general ways of designing and making topologically diversified porous colloidal crystals over the 10-1,000 nm length scale. Control over porosity in this size range would enable the tailoring of molecular absorption and storage, separation, chemical sensing, catalytic and optical properties of such materials. In this paper a universal approach for synthesizing metallic open-channel superlattices with pores of 10 to 1,000 nm from DNA-modified hollow colloidal nanoparticles (NPs) is reported. By tuning hollow NP geometry and DNA design, one can adjust crystal pore geometry (pore size and shape) and channel topology (the way in which pores are interconnected). The assembly of hollow NPs is driven by edge-to-edge rather than face-to-face DNA-DNA interactions. Two new design rules describing this assembly regime emerge from these studies and are then used to synthesize 12 open-channel superlattices with control over crystal symmetry, channel geometry and topology. The open channels can be selectively occupied by guests of the appropriate size and that are modified with complementary DNA (for example, Au NPs).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Beyond electrical conductance: progress and prospects in single-molecule junctions

The idea of using individual molecules as conducting wires, regulators, and interconnects for charges in electronic circuitry has catalyzed the vibrant development of the field of single-molecule electronics. The ability to reliably and repeatedly construct single-molecule junctions (SMJs) has enabled the study of charge transport through a broad spectrum of individual molecules. Over the past decade, the capability of the SMJ platform has been greatly expanded thanks to the development of new experimental techniques and the integration of knowledge and methodologies from other disciplines. New opportunities beyond electrical conductance have emerged at the atomic and molecular scale. It has been demonstrated in many recent studies that the SMJ can now serve as a powerful and versatile tool to address critical physical and chemical questions that are otherwise inaccessible. Furthermore, this perspective focuses on the new capabilities and functionalities of the SMJ beyond conductance measurements and how they have enabled the investigation of crucial single-molecule processes and advanced our understanding beyond molecular electronics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

NASA NTRS1987

Superstructure high efficiency photovoltaics

A novel class of photovoltaic cascade structures is introduced which features multijunction upper subcells. These superstructure high efficiency photovoltaics (SHEP's) exhibit enhanced upper subcell spectral response because of the additional junctions which serve to reduce bulk recombination losses by decreasing the mean collection distance for photogenerated minority carriers. Two possible electrical configurations were studied and compared: a three-terminal scheme that allows both subcells to be operated at their individual maximum power points and a two-terminal configuration with an intercell ohmic contact for series interconnection. The three-terminal devices were found to be superior both in terms of beginning-of-life expectancy and radiation tolerance. Realistic simulations of three-terminal AlGaAs/GaAs SHEP's show that one sun AMO efficiencies in excess of 26 percent are possible.

Wagner, M.↗

NASA NTRS1987

Disturbance and vibration isolation in space stations by means of mechanical decoupling

A decoupling approach to disturbance and vibration isolation in large space stations composed of modules interconnected by flexible members is proposed. A simplified mathematical model for the motion of the space station core and a laboratory module with both torsional vibration and translational motion decouplers is used in this study. The dynamic behavior of the model in the presence of decoupler friction is analyzed. Estimates for the maximum excursions of the laboratory module induced by various types of external disturbance are derived. The paper concludes with a simulation study involving the hard-docking of a space shuttle with a space station.

Wang, P. K. C.↗

NASA NTRS1992

Dynamic analysis of flexible gear trains/transmissions - An automated approach

In this paper an automated algorithmic method is presented for the dynamic analysis of geared trains/transmissions. These are treated as a system of interconnected flexible bodies. The procedure developed explains the switching of constraints with time as a result of the change in the contacting areas at the gear teeth. The elastic behavior of the system is studied through the employment of three-dimensional isoparametric elements having six degrees-of-freedom at each node. The contact between the bodies is assumed at the various nodes, which could be either a line or a plane. The kinematical expressions, together with the equations of motion using Kane's method, strain energy concepts, are presented in a matrix form suitable for computer implementation. The constraint Jacobian matrices are generated automatically based on the contact information between the bodies. The concepts of the relative velocity at the contacting points at the tooth pairs and the subsequent use of the transmission ratios in the analysis is presented.

Amirouche, F. M. L.↗

DOE OSTI2020

Enhanced Dynamic Equivalent Identification Method of Large-Scale Power Systems Using Multiple Event

The increasing complexity of the interconnected power system makes high-fidelity dynamic simulation models computationally more intensive. To improve computation efficiency, model reduction techniques have been investigated to only preserve the dynamics in a limited area of interest (study area), while deriving equivalent representation for the external area. For this purpose, a measurement-based reduction approach using system identification techniques has been previously proposed. In that case, external areas are represented by dynamic equivalent loads using transfer function estimation. In this paper, in order to enhance the accuracy of the reduced model in preserving dynamics of the study area, multiple “grid” events of different types and at different locations are considered for identifying the parameters of the equivalent loads. Case studies are carried out in the NPCC 140-bus system. Comparison are made between multiple events training and single event training, highlighting the advantages of the proposed method in providing a better representation of the grid dynamics under different operating conditions.

Xue, Yaosuo↗