Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “incompressible flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Investigation of Separation of the Turbulent Boundary Layer

An investigation was conducted on a turbulent boundary layer near a smooth surface with pressure gradients sufficient to cause flow separation. The reynolds number was high, but the speeds were entirely within the incompressible flow range. The investigation consisted of measurements of mean flow, three components of turbulence intensity, turbulent shearing stress, and correlations between two fluctuation components at a point and between the same component of different points. The results are given in the form of tables and graphs. The discussion deals first with separation and then with the more fundamental question of basic concepts of turbulent flow.

Schubauer, G B↗
NASA NTRS1993

FAS multigrid calculations of three dimensional flow using non-staggered grids

Grid staggering is a well known remedy for the problem of velocity/pressure coupling in incompressible flow calculations. Numerous inconveniences occur, however, when staggered grids are implemented, particularly when a general-purpose code, capable of handling irregular three-dimensional domains, is sought. In several non-staggered grid numerical procedures proposed in the literature, the velocity/pressure coupling is achieved by either pressure or velocity (momentum) averaging. This approach is not convenient for simultaneous (block) solvers that are preferred when using multigrid methods. A new method is introduced in this paper that is based upon non-staggered grid formulation with a set of virtual cell face velocities used for pressure/velocity coupling. Instead of pressure or velocity averaging, a momentum balance at the cell face is used as a link between the momentum and mass balance constraints. The numerical stencil is limited to 9 nodes (in 2D) or 27 nodes (in 3D), both during the smoothing and inter-grid transfer, which is a convenient feature when a block point solver is applied. The results for a lid-driven cavity and a cube in a lid-driven cavity are presented and compared to staggered grid calculations using the same multigrid algorithm. The method is shown to be stable and produce a smooth (wiggle-free) pressure field.

Matovic, D.↗
NASA NTRS1996

Thermal analysis of HGFQ using FIDAP(trademark): Solidification front motion

The High Gradient Furnace with Quench (HGFQ) is being designed by NASA/MSFC for flight on the International Space Station. The furnace is being designed specifically for solidification experiments in metal and metallic alloy systems. The HGFQ Product development Team (PDT) has been active since January 1994 and their effort is now in early Phase B. Thermal models have been developed both by NASA and Sverdrup (support contractor) to assist in the HGFQ design effort. Both these models use SINDA as a solution engine, but the NASA model was developed using PATRAN and includes more detail than the Sverdrup model. These models have been used to guide design decisions and have been validated through experimentation on a prototypical 'Breadboard' furnace at MSFC. One facet of the furnace operation of interest to the designers is the sensitivity of the solidification interface location to changes in the furnace setpoint. Specifically of interest is the motion (position and velocity) of the solidification front due to a small perturbation in the furnace temperature. FIDAP(TM) is a commercially available finite element program for analysis of heat transfer and fluid flow processes. Its strength is in solution of the Navier-Stokes equations for incompressible flow, but among its capabilities is the analysis of transient processes involving radiation and solidification. The models presently available from NASA and Sverdrup are steady-state models and are incapable of computing the motion of the solidification front. The objective of this investigation is to use FIDAP(TM) to compute the motion of the solidification interface due to a perturbation in the furnace setpoint.

Woodbury, Keith A.↗
NASA NTRS1993

On solving the compressible Navier-Stokes equations for unsteady flows at very low Mach numbers

The properties of a preconditioned, coupled, strongly implicit finite-difference scheme for solving the compressible Navier-Stokes equations in primitive variables are investigated for two unsteady flows at low speeds, namely the impulsively started driven cavity and the startup of pipe flow. For the shear-driven cavity flow, the computational effort was observed to be nearly independent of Mach number, especially at the low end of the range considered. This Mach number independence was also observed for steady pipe flow calculations; however, rather different conclusions were drawn for the unsteady calculations. In the pressure-driven pipe startup problem, the compressibility of the fluid began to significantly influence the physics of the flow development at quite low Mach numbers. The present scheme was observed to produce the expected characteristics of completely incompressible flow when the Mach number was set at very low values. Good agreement with incompressible results available in the literature was observed.

Pletcher, R. H.↗
NASA NTRS1993

On solving the compressible Navier-Stokes equations for unsteady flows at very low Mach numbers

The properties of a preconditioned, coupled, strongly implicit finite difference scheme for solving the compressible Navier-Stokes equations in primitive variables are investigated for two unsteady flows at low speeds, namely the impulsively started driven cavity and the startup of pipe flow. For the shear-driven cavity flow, the computational effort was observed to be nearly independent of Mach number, especially at the low end of the range considered. This Mach number independence was also observed for steady pipe flow calculations; however, rather different conclusions were drawn for the unsteady calculations. In the pressure-driven pipe startup problem, the compressibility of the fluid began to significantly influence the physics of the flow development at quite low Mach numbers. The present scheme was observed to produce the expected characteristics of completely incompressible flow when the Mach number was set at very low values. Good agreement with incompressible results available in the literature was observed.

Pletcher, R. H.↗
NASA NTRS1986

Sharply curved turn around duct flow predictions using spectral partitioning of the turbulent kinetic energy and a pressure modified wall law

Computational predictions of turbulent flow in sharply curved 180 degree turn around ducts are presented. The CNS2D computer code is used to solve the equations of motion for two-dimensional incompressible flows transformed to a nonorthogonal body-fitted coordinate system. This procedure incorporates the pressure velocity correction algorithm SIMPLE-C to iteratively solve a discretized form of the transformed equations. A multiple scale turbulence model based on simplified spectral partitioning is employed to obtain closure. Flow field predictions utilizing the multiple scale model are compared to features predicted by the traditional single scale k-epsilon model. Tuning parameter sensitivities of the multiple scale model applied to turn around duct flows are also determined. In addition, a wall function approach based on a wall law suitable for incompressible turbulent boundary layers under strong adverse pressure gradients is tested. Turn around duct flow characteristics utilizing this modified wall law are presented and compared to results based on a standard wall treatment.

Santi, L. Michael↗
NASA NTRS1974

A rapid numerical solution to subsonic flow over planar and axisymmetric profiles at an angle of attack of 0 deg

A numerical solution is presented for the incompressible flow over thin planar and axisymmetric profiles at an angle of attack of 0 degrees. The method uses a finite-difference field solution to the governing equation with a Gauss-Seidel successive overrelaxation scheme. However, the use of a simple Cartesian grid system restricts this method to slender profiles. Results are presented for a cambered airfoil, airfoil in wall effect (two-dimensional flowthrough inlet), body of revolution, and flowthrough nacelle. A computer program is presented which can be used for any of the previously mentioned cases with simple input changes. Results for compressible flow are available with the use of the appropriate two-dimensional or axisymmetric compressibility corrections. Computational time for a typical field calculation of 3000 grid points and 200 cycles through the field is less than 1 minute with less than 50,000 octal storage on the Control Data Corporation 6600 computing system.

Mascitti, V. R.↗
NASA NTRS1982

The obstacle block as a device to measure turbulent skin friction in compressible flow

The obstacle block, developed as an alternative to the Preston tube for indirectly measuring skin friction on smooth surfaces in incompressible flows, is examined as a device for compressible flows as well. The block, which is congruent with a surface static pressure orifice, has a geometry which is easily specified and thus has a universal calibration. Data from two independent studies are used to establish such a calibration using 'wall' variables, valid for Mach numbers up to about 3. Various aspects concerning practical application of the device are examined, such as sensitivity to yaw and the minimum permissible axial spacing between blocks. Several examples showing the utility of the device are given.

Elfstrom, G. M.↗
NASA NTRS1950

Some Studies on the Flow of a Gas in the Region of Transition Through the Velocity of Sound

The two-dimensional motion of an incompressible fluid about a closed contour with a definite velocity in magnitude and direction at infinity is considered. If, without changing the direction of the velocity at infinity, the magnitude is increased, the configuration of the streamlines remains unchanged and only the numbering of the stream function changes. There exists only one family of curves that can serve as streamlines in the incompressible flow about a given contour (at a given angle of attack); for example, the contour of an airplane wing. The case is quite different with a compressible fluid.

Kiebel, I. A.↗
NASA NTRS1982

A simple finite difference procedure for the vortex controlled diffuser

A simple prediction procedure for sudden expansion incompressible flows is developed and applied to the vortex controlled diffuser. Transient Navier-Stokes equations of an incompressible fluid are solved by means of their associated finite difference equations in terms of the primitive pressure velocity variables. A computer code is developed using a laminar flow simulation with free slip or no slip wall boundary conditions. In addition, predicted results confirm that effectiveness increases with increases in duct length and bleed flow rate

Busnaina, A. A.↗
NASA NTRS1976

Numerical computation of transient coaxial entry tube flows

A numerical program was developed to compute transient laminar flows in two dimensions including multicomponent mixing and chemical reaction. The program can compute both incompressible flows and compressible flows at all speeds, and it is applied to describe transient and steady state solutions for low subsonic, coaxial entry, tue flows. Single component, nonreacting flows comprise most of the solutions, but one steady state solution is presented for trace concentration constituents engaging in a second order reaction. Numerical stability was obtained by adding at each calculation point a correction for numerical diffusion errors caused by truncation of the Taylor series used to finite difference the conservation equations. Transient computations were made for fluids initially at rest, then subjected to step velocity inputs that were uniform across each region of the entry plane and were held constant throughout the computation period. For center tube to annulus velocity ratios of 0.5 and 2.0, the bulk fluid in the tube initially moved in plug flow, but strong radial flows developed near the injection plane which moved the fluid into the high shear region between the jets and away from the tube wall.

Wieber, P. R.↗
NASA NTRS1988

Extension of the Johnson-King turbulence model to the 3-D flows

A critical evaluation of the eddy viscosity model of Johnson and King extended to the three-dimensional case has been performed for three-dimensional boundary layer flows. The turbulence model is evaluated by a detailed comparison with available experimental data for incompressible flows over an infinite swept wing and near an idealized wing-body junction. The isotropic model of Johnson and King is found to work much better than the Cebeci-Smith model, especially in regions of strong cross flow. The significant decrease in the shear stress magnitude is almost reproduced. This means that this effect is as important as the nonisotropic eddy viscosity. The introduction of Rotta's modification to account for nonisotropic eddy viscosity in the Johnson-King formulation is found to have little effect on the predictions. The cross-flow properties are the most strongly affected.

Abid, Ridha↗
NASA NTRS1989

Application of large eddy interaction model to a mixing layer

The large eddy interaction model (LEIM) is a statistical model of turbulence based on the interaction of selected eddies with the mean flow and all of the eddies in a turbulent shear flow. It can be utilized as the starting point for obtaining physical structures in the flow. The possible application of the LEIM to a mixing layer formed between two parallel, incompressible flows with a small temperature difference is developed by invoking a detailed similarity between the spectra of velocity and temperature.

Murthy, S. N. B.↗
NASA NTRS2010

Minnowbrook VI: 2009 Workshop on Flow Physics and Control for Internal and External Aerodynamics

Topics covered include: Flow Physics and control for Internal and External Aerodynamics (not in TOC...starts on pg13); Breaking CFD Bottlenecks in Gas-Turbine Flow-Path Design; Streamwise Vortices on the Convex Surfaces of Circular Cylinders and Turbomachinery Blading; DNS and Embedded DNS as Tools for Investigating Unsteady Heat Transfer Phenomena in Turbines; Cavitation, Flow Structure and Turbulence in the Tip Region of a Rotor Blade; Development and Application of Plasma Actuators for Active Control of High-Speed and High Reynolds Number Flows; Active Flow Control of Lifting Surface With Flap-Current Activities and Future Directions; Closed-Loop Control of Vortex Formation in Separated Flows; Global Instability on Laminar Separation Bubbles-Revisited; Very Large-Scale Motions in Smooth and Rough Wall Boundary Layers; Instability of a Supersonic Boundary-Layer With Localized Roughness; Active Control of Open Cavities; Amplitude Scaling of Active Separation Control; U.S. Air Force Research Laboratory's Need for Flow Physics and Control With Applications Involving Aero-Optics and Weapon Bay Cavities; Some Issues Related to Integrating Active Flow Control With Flight Control; Active Flow Control Strategies Using Surface Pressure Measurements; Reduction of Unsteady Forcing in a Vaned, Contra-Rotating Transonic Turbine Configuration; Active Flow Control Stator With Coanda Surface; Controlling Separation in Turbomachines; Flow Control on Low-Pressure Turbine Airfoils Using Vortex Generator Jets; Reduced Order Modeling Incompressible Flows; Study and Control of Flow Past Disk, and Circular and Rectangular Cylinders Aligned in the Flow; Periodic Forcing of a Turbulent Axisymmetric Wake; Control of Vortex Breakdown in Critical Swirl Regime Using Azimuthal Forcing; External and Turbomachinery Flow Control Working Group; Boundary Layers, Transitions and Separation; Efficiency Considerations in Low Pressure Turbines; Summary of Conference; and Final Plenary Session Transcript.

LaGraff, John E.↗
DOE OSTI2022

A mass–momentum consistent coupling for mesh-adaptive two-phase flow simulations

Here, we present a novel mass-momentum consistent coupling between a geometric volume-of-fluid scheme and an incompressible flow solver with differing directional-splitting approaches. The advection of the volume fraction is performed using a direction-split algorithm, whereas the momentum advection algorithm uses a traditional unsplit, fractional-step approach. Both algorithms employ finite-volume discretizations based on Cartesian meshes. In solving the mass-momentum consistency problem, momentum fluxes at the cell faces are weighted by the density fluxes based on the already advected volume fraction. The success of our approach lies on introducing a Favre-averaged velocity interpolation at the liquid/gas interface along with a minmod slope limiter. Mesh-convergence studies show that when the minmod slope limiter is used, the two-phase solver retains an accuracy between first and second order, but when a purely upwind scheme is considered, its accuracy drops to first order. Finally, after considering several validation problems, the solver is shown to agree well with reference numerical and experimental data while retaining its robustness and efficiency.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1976

A complete second-order theory for the unsteady flow about an airfoil due to a periodic gust

A uniformly valid second-order theory is developed for calculating the unsteady incompressible flow that occurs when an airfoil is subjected to a convected sinusoidal gust. Explicit formulas for the airfoil response functions (i.e., fluctuating lift) are given. The theory accounts for the effect of the distortion of the gust by the steady-state potential flow around the airfoil, and this effect is found to have an important influence on the response functions. A number of results relevant to the general theory of the scattering of vorticity waves by solid objects are also presented.

Goldstein, M. E.↗
NASA NTRS1985

A three-dimensional boundary-layer method for flow over delta wings with leading-edge separation

A three-dimensional, laminar boundary-layer method is applied to the incompressible flow over a slender delta wing at incidence. The predictor-corrector finite-difference scheme of Matsuno is used to difference the governing equations. The method has the advantages that no iterations are required to advance the solution and the cross-flow derivatives are formed independent of the cross-field direction. The difference scheme is demonstrated to yield accurate numerical results when compared to the exact solution of the three-dimensional boundary-layer equations for parabolic flow over a moving flat plate. The method is applied to delta wings of various sweep angles at angles of attack up to 20 deg., with the inviscid solution determined using a higher-order, three-dimensional panel method.

Woodson, S. H.↗
NASA NTRS1975

Numerical simulation of interacting, three-dimensional vortex filaments

Unsteady three-dimensional fluid flows which are characterized by low viscosity and the presence of distinct regions of high vorticity embedded in an otherwise irrotational flow are considered, taking into account the case in which an intermingling of vortex filaments appears. Incompressible flows of the considered type are simulated with the aid of an approach in which the vorticity distribution is modeled in terms of continuous closed filaments. It is attempted to track these filaments in a Lagrangian reference frame.

Leonard, A.↗