Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrogen compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Concentration of interstellar pickup H(+) and He(+) in the solar wind

We present observations of interstellar pickup hydrogen and helium in the solar wind which show large, highly-correlated fluctuations in flux which are not correlated significantly with the solar-wind hydrogen flux. The correlation of the fluctuations in the two species implies that the fluctuations are caused by transport after ionization. The lack of correlation with the thermal flux means they are not caused by compressions of the wind. We present a new model which can naturally produce the observed fluctuations in the pickup ions.

Gloeckler, G.↗
NASA NTRS2012

Titanium-Water Thermosyphon Gamma Radiation Exposure and Results

Titanium-water thermosyphons are being considered for use in heat rejection systems for fission power systems. Their proximity to the nuclear reactor will result in some gamma irradiation. Noncondensable gas formation from radiation-induced breakdown of water over time may render portions of the thermosyphon condenser inoperable. A series of developmental thermosyphons were operated at nominal operating temperature under accelerated gamma irradiation, with exposures on the same order of magnitude as that expected in 8 years of heat rejection system operation. Temperature data were obtained during exposure at three locations on each thermosyphon: evaporator, condenser, and condenser end cap. Some noncondensable gas was evident; however, thermosyphon performance was not affected because the noncondensable gas was compressed into the fill tube region at the top of the thermosyphon, away from the heat rejecting fin. The trend appeared to be an increasing amount of noncondensable gas formation with increasing gamma irradiation dose. Hydrogen is thought to be the most likely candidate for the noncondensable gas and hydrogen is known to diffuse through grain boundaries. Post-exposure evaluation of one thermosyphon in a vacuum chamber and at temperature revealed that the noncondensable gas diffused out of the thermosyphon over a relatively short period of time. Further research shows a number of experimental and theoretical examples of radiolysis occurring through gamma radiation alone in pure water.

Sanzi, James, L.A↗
NASA NTRS1988

Filament wound metal lined propellant tanks for future Earth-to-orbit transports

For future Earth-to-orbit transport vehicles, reusability and lighter weights are sought for the main propellant tanks. To achieve this, a filament wound tank with a metal liner and an intermediate layer of foam-filled honeycomb is proposed. A hydrogen tank is used as an example. To accommodate mismatches in the expansion of liner and overwrap a design is proposed wherin the liner is configured so that the extension of the liner under pressure matches the expected contraction of the same liner due to the presence of a cryogen. In operation, the liner is pressurized at a rate such that the pressure strain matches the contraction due to decrease in temperature. As an alternate approach, compressive pre-stress is placed in the liner such that it will not separate from the overwrap. A finite element program is used to show stresses in the liner and overwrap for various tank pressures for the pre-stressed liner concept. A fracture mechanics analysis is made of the liners to determine tank life. The tank concept shown has a similar weight to the Shuttle external hydrogen tank, but the filament wound tank is expected to be reusable. Integration of the propellant tanks into a future transport vehicle is discussed.

Macconochie, Ian O.↗
DOE OSTI2025

Biermann-Battery-Driven Magnetized Collisionless Shock Precursors in Laser-Produced Plasmas

This Letter reports the first complete observation of magnetized collisionless shock precursors formed through the compression of Biermann-battery magnetic fields in laser produced plasmas. At OMEGA, lasers produce a supersonic CH plasma flow which is magnetized with Biermann-battery magnetic fields. The plasma flow collides with an unmagnetized hydrogen gas jet plasma to create a magnetized shock precursor. The situation where the flowing plasma carries the magnetic field is similar to the Venusian bow shock. Imaging 2⁢𝜔 Thomson scattering confirms that the interaction is collisionless and shows density and temperature jumps. Proton radiographs have regions of strong deflections and FLASH magnetohydrodynamic (MHD) simulations show the presence of Biermann fields in the Thomson scattering region. Electrons are accelerated to energies of up to 100 keV in a power-law spectrum. Here, OSIRIS particle-in-cell (PIC) simulations, initialized with measured parameters, show the formation of a magnetized shock precursor and corroborate the experimental observables.

High-energy-density plasmas↗
NASA NTRS1984

Shock compression of liquid helium to 56 GPa (560 kbar)

Shock-wave data are presented for liquid helium which has been compressed to densities up to five times greater than the normal liquid. The helium was heated to temperatures up to 21,000 K, while the maximum pressure attained was 56 GPa. The properties of helium and hydrogen are important for modeling the giant planets Saturn and Jupiter where these elements are the major constituents. Conditions on Saturn are of particular interest because studies have suggested that this planet has an internal energy source which is associated with unmixing and gravitational separation of the hydrogen-helium fluid at pressures below 1 TPa. The existence of this phase transition depends very sensitively on the hydrogen and helium equation of state. In the experiments, strong shock waves were generated by the impact of planar projectiles into cryogenic specimen holders.

Nellis, W. J.↗
NASA NTRS1985

Shock Compression of Liquid Helium to 56 GPa (560) Kbar

Shock-wave data are presented for liquid helium which has been compressed to densities up to five times greater than the normal liquid. The helium was heated to temperatures up to 21,000 K, while the maximum pressure attained was 56 GPa. The properties of helium and hydrogen are important for modeling the giant planets Saturn and Jupiter where these elements are the major constituents. Conditions on Saturn are of particular interest because studies have suggested that this planet has an internal energy source which is associated with unmixing and gravitational separation the hydrogen-helium fluid at pressures below 1 TPa. The existence of this phase transition depends very sensitively on the hydrogen and helium equation of state. In the experiments, strong shock waves were generated by the impact of planar projectiles into cryogenic specimen holders.

Nellis, W. J.↗
DOE OSTI2021

Mechanical and physical properties of inorganic polymer cement made of iron-rich laterite and lateritic clay: A comparative study

In this work, two different laterites (iron contents of 13.07 and 49.34 wt%, respectively, for lateritic clay, LAC, and iron-rich laterite, LAI) were selected and calcined at 600 °C. The obtained calcined laterites, namely LAI600 and LAC600, were separately mixed with an alkaline solution (silicate modulus of 1.35) or an acidic solution (phosphoric acid solution at pH ≤ 2) for the synthesis of inorganic polymer products. The fabricated products were cured at 20 °C (ambient) and 40 °C (oven). The obtained results showed that the compressive strength of each series of alkaline-based inorganic polymer binder increased with ageing time (7 and 28 days) for room temperature curing, while the reverse trend was noted for oven-cured specimens. The best mechanical performance was obtained when using a phosphoric acid solution, 38 and 52 ± 1 MPa; 62 and 65 ± 1 MPa at 28 days for LAC and LAI respectively. It appeared that a higher iron content within the laterite contributed to an increase in the compressive strength under acidic conditions (LAI (59 MPa) > LAC (48 MPa)) compared to the behavior obtained under alkaline conditions (LAI (6 MPa) < LAC (29 MPa)). Accordingly, the acidic products exhibited a dense structure (with lower porosity) and contained amorphous iron/aluminium phosphate phases such as berlinite (FePO{sub 4}), iron hydrogen phosphate hydrate (Fe{sub 3}H{sub 15}(PO{sub 4}){sub 8·}4H{sub 2}O), ferrowyllieite (AlFe{sub 2}Na{sub 2}(PO{sub 4}){sub 3}) and sodium iron phosphate (Na{sub 3}Fe{sub 2}(PO{sub 4}){sub 3}) arising from the alteration of iron minerals in an acidic medium, confirmed by Mössbauer spectroscopy and electron paramagnetic resonance spectroscopy.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Experiments and analysis concerning the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce transonic drag was investigated. A control volume analysis is developed and indicates that the specific impulse performance of external burning is competitive with other forms of airbreathing propulsion and depends on the fuel-air ratio, freestream Mach number, and the severity of the base drag. A method is presented for sizing fuel injectors for a desired fuel-air ratio in the unconfined stream. A two-dimensional Euler analysis is also presented which indicates that the total axial force generated by external burning depends on the total amount of energy input and is independent of the transverse and streamwise distribution of heat addition. Good agreement between the Euler and control volume analysis is demonstrated. Features of the inviscid external burning flowfield are discussed. Most notably, a strong compression forms at the sonic line within the burning stream which may induce separation of the plume and prevent realization of the full performance potential. An experimental program was conducted in a Mach 1.26 free-jet to demonstrate drag reduction on a simple expansion ramp geometry, and verify hydrogen-air stability limits at external burning conditions. Stable combustion appears feasible to Mach number of between 1.4 and 2 depending on the vehicle flight trajectory. Drag reduction is demonstrated on the expansion ramp at Mach 1.26; however, force levels showed little dependence on fuel pressure or altitude in contrast to control volume analysis predictions. Various facility interference mechanisms and scaling issues were studied and are discussed.

Trefny, Charles J.↗
DOE OSTI2024

Dislocation-Activated Low Platinum-Loaded PtCu Nanoparticles Welded onto the Substrate for Practical Acidic Hydrogen Generation

Although transition metal (M) alloying with platinum (Pt) is a promising approach to reduce the Pt dosage required in the hydrogen evolution reaction (HER), the catalytic activity and durability of PtM alloy are often unsatisfactory for acidic HER, especially at high currents, due to a reduced number of highly active sites (Pt) at the atomic level and challenges in stabilizing them to prevent detachment and aggregation. Herein, we report a robust functional structure integrated electrode (D-PtCu/CF) with abundant edge dislocations and very low platinum content (0.1 mg cm -2 ) to achieve high activity and stability in acidic HER within a proton exchange membrane water electrolysis cell (PEMWE). D-PtCu/CF exhibits high Pt mass activity (10.28 A mg Pt -1 ) and excellent operational stability (negligible decay after 200 h). X-ray absorption spectroscopy and in situ electrochemical experiments reveal that the lattice distortion caused by edge dislocations in PtCu mainly affects Pt atoms by compressing strain, reducing their ability to adsorb H. At the same time, Cu atoms are subjected to tensile strain, enhancing the bonding between Cu and H. Therefore, edge dislocations not only improve the intrinsic catalytic activity of Pt atoms but also increase the number of active sites (Cu) available for hydrogen adsorption, which synergistically accelerates the kinetics of the HER reaction. Finally, the PEMWE employing the D-PtCu/CF catalytic electrode can operate stably for 100 h at an industrial-level current density of 500 mA cm -2 with 1.63 V.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS2012

Titanium-Water Thermosyphon Gamma Radiation Effects and Results

Titanium-water thermosyphons are being considered for use in heat rejection systems for fission power systems. Their proximity to the nuclear reactor will result in some exposure to gamma irradiation. Non-condensable gas formation from radiation may breakdown water over time and render a portion of the thermosyphon condenser inoperable. A series of developmental thermosyphons were operated at nominal operating temperature with accelerated gamma irradiation exposures on the same order of magnitude that is expected in eight years of heat rejection system operation. Temperature data were obtained during exposure at three locations on each thermosyphon; evaporator, condenser, and condenser end cap. Some non-condensable gas was evident, however thermosyphon performance was not affected because the non-condensable gas was compressed into the fill tube region at the top of the thermosyphon, away from the heat rejecting fin. The trend appeared to be an increasing amount of non-condensable gas formation with increasing gamma irradiation dose. Hydrogen is thought to be the most likely candidate for the non-condensable gas and hydrogen is known to diffuse through grain boundaries. Post-exposure evaluation of selected thermosyphons at temperature and in a vacuum chamber revealed that the non-condensable gas likely diffused out of the thermosyphons over a relatively short period of time. Further research shows a number of experimental and theoretical examples of radiolysis occurring through gamma radiation alone in pure water.

Sanzi, James L.↗
DOE OSTI2021

Performance and Durability of Pure-Water-Fed Anion Exchange Membrane Electrolyzers Using Baseline Materials and Operation

Water electrolysis powered by renewable electricity produces green hydrogen and oxygen gas, which can be used for energy, fertilizer, and industrial applications and thus displace fossil fuels. Pure-water anion-exchange-membrane (AEM) electrolyzers in principle offer the advantages of commercialized proton-exchange-membrane systems (high current density, low cross over, output gas compression, etc.) while enabling the use of less-expensive steel components and nonprecious metal catalysts. AEM electrolyzer research and development, however, has been limited by the lack of broadly accessible materials that provide consistent cell performance, making it difficult to compare results across studies. Further, even when the same materials are used, different pretreatments and electrochemical analysis techniques can produce different results. Here, we report an AEM electrolyzer comprising commercially available catalysts, membrane, ionomer, and gas-diffusion layers operating near 1.9 V at 1 A cm –2 in pure water. After the initial break in, the performance degraded by 0.67 mV h –1 at 0.5 A cm –2 at 55 °C. We detail the key preparation, assembly, and operation techniques employed and show further performance improvements using advanced materials as a proof-of-concept for future AEM-electrolyzer development. Here, the data thus provide an easily reproducible and comparatively high-performance baseline that can be used by other laboratories to calibrate the performance of improved cell components, nonprecious metal oxygen evolution, and hydrogen evolution catalysts and learn how to mitigate degradation pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Reduction of liquid hydrogen boiloff: Optimal reliquefaction system design and cost study

The refrigeration cycles investigated are referred to as Joule-Thomson cycles because they depend on the J-T effect to produce the low temperatures. Two basic competitive refrigeration cycles were evaluated. The first vents a portion of cold H2 gas to achieve the required precooling; the second uses LN2 for precooling. Both open loop and closed loop cycles were evaluated as well as combinations of venting to supplement the LN2 precooling. All cycles use a H2 compressor to achieve the desired high pressure (1325 psig). The heat compression was removed by cooling water. The high pressure H2 gas was cooled in counter flow heat exchangers by flowing cold H2 to the compressor. Further cooling was achieved for cycles using LN2 by passing H2 vapors through a LN2 heat exchanger. Finally, the high pressure H2 gas was expanded through a J-T valve where a portion of H2 was liquefied. The low pressure H2 gas flow back through the heat exchangers to the compressor is that portion not liquefied and makes up hydrogen gas from the dewar.

Source record↗
DOE OSTI2022

Anomalies and Local Structure of Liquid Water from Boiling to the Supercooled Regime as Predicted by the Many-Body MB-pol Model

For the past 50 years, researchers have sought molecular models that can accurately reproduce water’s microscopic structure and thermophysical properties across broad ranges of its complex phase diagram. Herein, molecular dynamics simulations with the many-body MB-pol model are performed to monitor the thermodynamic response functions and local structure of liquid water from the boiling point down to deeply supercooled temperatures at ambient pressure. The isothermal compressibility and isobaric heat capacity show maxima near 223 K, in excellent agreement with recent experiments, and the liquid density exhibits a minimum at ~208 K. A local tetrahedral arrangement, where each water molecule accepts and donates two hydrogen bonds, is found to be the most probable hydrogen-bonding topology at all temperatures. Further, this work suggests that MB-pol may provide predictive capability for studies of liquid water’s physical properties across broad ranges of thermodynamic states, including the so-called water’s “no man’s land” which is difficult to probe experimentally.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Methanol from Integrated Direct Air Capture and Ceramic Electrolysis (MIDACE)

The Methanol from Integrated Direct Air Capture and Ceramic Electrolysis (MIDACE) project advanced a novel system concept for integrating pressurized co-electrolysis of steam and crude carbon dioxide captured directly from ambient air using a sorbent technology. The co-electrolysis produced syngas provides feedstock for a gas-to-liquid methanol synthesis reactor. The system recovers waste heat from the reactor and electrolyzer into regenerating the direct air capture sorbent. The purpose of the project was to demonstrate critical integration elements of the design and perform a technical study illustrating how a large-scale installation could achieve the $800/ton program target for green methanol production. The concept addresses the program objective to consolidate operations by combining crude CO 2 cleanup, hydrogen production, and partial CO 2 reduction steps within a carbon tolerant high temperature electrolyzer. The design lowers costs by simplifying the methanol recovery cycle, reducing carbon losses from venting, reducing sensitivity to catalyst selectivity, and avoiding syngas compression.

10 SYNTHETIC FUELS↗
NASA NTRS1969

Two-functional seal for hose connection

Seal, machined from a plastic material, prevents liquid hydrogen leakage from hose connectors. It serves as a block-type seal supporting maximum loading of the poppet with slight elastic deflection or as a lip-type seal that is deformed elastically in bending, tension, or compression by the seated poppet.

Richardson, M. B.↗
NASA NTRS2003

Dissociation and Recombination Effects on the Performance of Pulse Detonation Engines

This paper summarizes major theoretical results for pulse detonation engine performance taking into account real gas chemistry, as well as significant performance differences resulting from the presence of ram and compression heating. An unsteady CFD analysis, as well as a thermodynamic cycle analysis, was conducted in order to determine the actual and the ideal performance for an air-breathing pulse detonation engine (PDE) using either a hydrogen-air or ethylene-air mixture over a flight Mach number range from 0 to 4. The results clearly elucidate the competitive regime of PDE application relative to ramjets and gas turbines.

Povinelli, Louis A.↗
DOE OSTI2024

Atomic cluster expansion potential for large scale simulations of hydrocarbons under shock compression

We present an Atomic Cluster Expansion (ACE) machine learned potential developed for high-fidelity atomistic simulations of hydrocarbons, targeting pressures and temperatures near and above supercritical fluid regimes for molecular fluids. A diverse set of stoichiometries were covered in training, including 1:0 (pure carbon), 1:4 (methane), and 1:1 (benzene), and rich bonding environments sampled at supercritical temperatures, hydrogen rich, reactive mixtures where metastable stoichiometries arise, including 1:2 (ethylene) and 1:3 (ethane). A high-fidelity training database was constructed by performing large-scale quantum molecular dynamic simulations [density functional theory (DFT) MD] of diamond, graphite, methane, and benzene. A novel approach to selecting structures from DFT MD is also presented, which allows for the rapid selection of unique DFT MD frames from complex trajectories. Comparisons to DFT and experimental data demonstrate that the presented ACE potential accurately reproduces isotherms, carbon melting curves, radial distribution functions, and shock Hugoniots for carbon and hydrocarbon systems for pressures up to 100 GPa and temperatures up to 6000 K for hydrocarbon systems and up to 9000 K for pure carbon systems. This work delivers a potential that can be used for accurate, large-scale simulations of shocked hydrocarbons and demonstrates a methodology for fitting and validating machine learning interatomic potentials to complex molecular environments, which can be applied to energetic materials in future works.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Phase I: Natural Gas-Based Energy Storage at Abbott Power Plant

Compressed Natural Gas Energy Storage (CNGES), uses the potential energy of compressed natural gas within an integrated energy storage system. Specifically, an inventory of high-pressure natural gas is stored during off-peak hours in a first stage by controlling the balance of gas entering a pipeline from the transmission system, and in a second stage by using new compressors to fill vessels onsite. The natural gas storage medium is then discharged through an expander-generator to use the potential energy from the gas to generate electricity without combustion. The excess chemical energy stored in the natural gas is integrated with an existing fossil-based asset to provide power generation during peak hours and increase the reliability of the associated fossil generating facility.

03 NATURAL GAS↗