Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gas composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Analysis of SOFCs Using Reference Electrodes

Reference electrodes are frequently applied to isolate the performance of one electrode in a solid oxide fuel cell. However, reference electrode simulations raise doubt to veracity of data collected using reference electrodes. The simulations predict that the reported performance for the one electrode will frequently contain performance of both electrodes. Nonetheless, recent reports persistently treat data so collected as ideally isolated. This work confirms the predictions of the reference electrode simulations on two SOFC designs, and to provides a method of validating the data measured in the 3-electrode configuration. Validation is based on the assumption that a change in gas composition to one electrode does not affect the impedance of the other electrode at open circuit voltage. This assumption is supported by a full physics simulation of the SOFC. Three configurations of reference electrode and cell design are experimentally examined using various gas flows and two temperatures. Impedance data are subjected to deconvolution analysis and equivalent circuit fitting and approximate polarization resistances of the cathode and anode are determined. The results demonstrate that the utility of reference electrodes is limited and often wholly inappropriate. Reported impedances and single electrode polarization values must be scrutinized on this basis.

30 DIRECT ENERGY CONVERSION↗

Blunt-Body Aerothermodynamic Database from High-Enthalpy CO2 Testing in an Expansion Tunnel

An extensive database of heating, pressure, and flow field measurements on a 70-deg sphere-cone blunt body geometry in high-enthalpy, CO2 flow has been generated through testing in an expansion tunnel. This database is intended to support development and validation of computational tools and methods to be employed in the design of future Mars missions. The test was conducted in an expansion tunnel in order to avoid uncertainties in the definition of free stream conditions noted in previous studies performed in reflected shock tunnels. Data were obtained across a wide range of test velocity/density conditions that produced various physical phenomena of interest, including laminar and transitional/turbulent boundary layers, non-reacting to completely dissociated post-shock gas composition and shock-layer radiation. Flow field computations were performed at the test conditions and comparisons were made with the experimental data. Based on these comparisons, it is recommended that computational uncertainties on surface heating and pressure, for laminar, reacting-gas environments can be reduced to +/-10% and +/-5%, respectively. However, for flows with turbulence and shock-layer radiation, there were not sufficient validation-quality data obtained in this study to make any conclusions with respect to uncertainties, which highlights the need for further research in these areas.

Hollis, Brian R.↗

Origin of stress in radio frequency magnetron sputtered zinc oxide thin films

Highly c-axis oriented ZnO thin films have been deposited on silicon substrates by planar rf magnetron sputtering under varying pressure (10-50 mTorr) and oxygen percentage (50-100%) in the reactive gas (Ar + O{sub 2}) mixture. The as-grown films were found to be stressed over a wide range from -1 x 10{sup 11} to -2 x 10{sup 8} dyne/cm{sup 2} that in turn depends strongly on the processing conditions, and the film becomes stress free at a unique combination of sputtering pressure and reactive gas composition. Raman spectroscopy and photoluminescence (PL) analyses identified the origin of stress as lattice distortion due to defects introduced in the ZnO thin film. FTIR study reveals that Zn-O bond becomes stronger with the increase in oxygen fraction in the reactive gas mixture. The lattice distortion or stress depends on the type of defects introduced during deposition. PL spectra show the formation of a shoulder in band emission with an increase in the processing pressure and are related to the presence of stress. The ratio of band emission to defect emission decreases with the increase in oxygen percentage from 50 to 100%. The studies show a correlation of stress with the structural, vibrational, and photoluminescence properties of the ZnO thin film. The systematic study of the stress will help in the fabrication of efficient devices based on ZnO film.

36 MATERIALS SCIENCE↗

Coal properties and system operating parameters for underground coal gasification

Through the model experiment for underground coal gasification, the influence of the properties for gasification agent and gasification methods on underground coal gasifier performance were studied. The results showed that pulsating gasification, to some extent, could improve gas quality, whereas steam gasification led to the production of high heating value gas. Oxygen-enriched air and backflow gasification failed to improve the quality of the outlet gas remarkably, but they could heighten the temperature of the gasifier quickly. According to the experiment data, the longitudinal average gasification rate along the direction of the channel in the gasifying seams was 1.212 m/d, with transverse average gasification rate 0.069 m/d. Experiment indicated that, for the oxygen-enriched steam gasification, when the steam/oxygen ratio was 2:1, gas compositions remained stable, with H{sub 2} + CO content virtually standing between 60% and 70% and O{sub 2} content below 0.5%. The general regularities of the development of the temperature field within the underground gasifier and the reasons for the changes of gas quality were also analyzed. The 'autopneumatolysis' and methanization reaction existing in the underground gasification process were first proposed.

01 COAL, LIGNITE, AND PEAT↗

Studies of supersonic, radiative plasma jet interaction with gases at the Prague Asterix Laser System facility

The interaction of laser driven jets with gas puffs at various pressures is investigated experimentally and is analyzed by means of numerical tools. In the experiment, a combination of two complementary diagnostics allowed to characterize the main structures in the interaction zone. By changing the gas composition and its density, the plasma cooling time can be controlled and one can pass from a quasiadiabatic outflow to a strongly radiation cooling jet. This tuning yields hydrodynamic structures very similar to those seen in astrophysical objects; the bow shock propagating through the gas, the shocked materials, the contact discontinuity, and the Mach disk. From a dimensional analysis, a scaling is made between both systems and shows the study relevance for the jet velocity, the Mach number, the jet-gas density ratio, and the dissipative processes. The use of a two-dimensional radiation hydrodynamic code, confirms the previous analysis and provides detailed structure of the interaction zone and energy repartition between jet and surrounding gases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Angular etching yields of polysilicon and dielectric materials in Cl{sub 2}/Ar and fluorocarbon plasmas

The angular etching yields of polysilicon in Cl{sub 2}/Ar plasmas, and dielectric materials (thermal silicon dioxide and low-k dielectric coral) in fluorocarbon plasmas, have been characterized in an inductively coupled plasma beam apparatus. The effects of ion energy, feed gas composition, and plasma source pressure are studied. The experimental results showed that these etching parameters had a significant impact on the resulting angular etching yield curve. In particular, the angular etching yield curve was more sputteringlike at low plasma source pressure and/or low effective gas percentage (Cl{sub 2} and C{sub 4}F{sub 8}), with a peak around 60 deg. -70 deg. off-normal ion incident angle. In contrast, ion-enhanced-etching-like angular curves, which dropped gradually with off-normal angle, were formed at high plasma source pressure and/or high effective gas percentage. Further analysis indicated that the effective neutral-to-ion flux ratio reaching the surface was the primary factor influencing the angular etching yield curve. More specifically, the angular etching yield curve had physical sputtering characteristics at low neutral-to-ion flux ratios; while etching process was really dominated by ion-enhanced etching at high ratios and the angular curve was ion-enhanced-etching-like. The polymer deposition effects are also discussed in this article.

36 MATERIALS SCIENCE↗

Combustion chemistry of ethanol: Ignition and speciation studies in a rapid compression facility [On the combustion chemistry of ethanol: Ignition and speciation studies in a rapid compression facility]

Here, ethanol remains the most important alternative fuel for the transportation sector. This work presents new experimental data on ethanol ignition, including stable species measurements, obtained with the University of Michigan rapid compression facility. Ignition delay times were determined from pressure histories of ignition experiments with stoichiometric ethanol–air mixtures at pressures of ~3–10 atm. Temperatures (880–1150 K) were controlled by varying buffer gas composition (Ar, N 2 , CO 2 ). High-speed imaging was used to record chemiluminescence during the experiments, which showed homogeneous ignition events. The results for ignition delay time agreed well with trends on the basis of previous experimental measurements. Speciation experiments were performed using fast gas sampling and gas chromatography to identify and quantify ethanol and 11 stable intermediate species formed during the ignition delay period. Simulations were carried out using a chemical kinetic mechanism available in the literature, and the agreement with the experimental results for ignition delay time and the intermediate species measured was excellent for the majority of the conditions studied. From the simulation results, ethanol + HO 2 was identified as an important reaction at the experimental conditions for both the ignition delay time and intermediate species measurements. Further studies to improve the accuracy of the rate coefficient for ethanol + HO 2 would improve the predictive understanding of intermediate and low-temperature ethanol combustion.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Mimicking Mars: A vacuum simulation chamber for testing environmental instrumentation for Mars exploration

We have built a Mars environmental simulation chamber, designed to test new electromechanical devices and instruments that could be used in space missions. We have developed this environmental system aiming at validating the meteorological station Rover Environment Monitoring Station of NASA's Mars Science Laboratory mission currently installed on Curiosity rover. The vacuum chamber has been built following a modular configuration and operates at pressures ranging from 1000 to 10{sup −6} mbars, and it is possible to control the gas composition (the atmosphere) within this pressure range. The device (or sample) under study can be irradiated by an ultraviolet source and its temperature can be controlled in the range from 108 to 423 K. As an important improvement with respect to other simulation chambers, the atmospheric gas into the experimental chamber is cooled at the walls by the use of liquid-nitrogen heat exchangers. This chamber incorporates a dust generation mechanism designed to study Martian-dust deposition while modifying the conditions of temperature, and UV irradiated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Compositional Analysis of Titan’s Atmosphere Using Spitzer Infrared Spectrograph Data

We present, for the first time, infrared spectra from the Spitzer Space Telescope’s Infrared Spectrograph (IRS) (2004-2008) of Titan in both the short wavelength-low resolution(SL, R=60~127,5.13-14.29 μm) and short wavelength-high resolution channels (SH, R=600, 9.89-19.51 μm) showing the emissions of CH4, C2H4, C2H2, C2H6, HCN, CO2, HC3N, C3H4, C4H2, and C3H8. Spitzer IRS data has been used to measure atmospheric composition of various Solar System bodies, including Neptune [1] and Uranus [2],[3]. Although Spitzer took multiple dedicated observations of Titan, none of the results have been modeled before. We conduct our own investigation of these datasets and search for new results. We retrieve temperature and gas composition profiles and compare the results obtained for Titan to those of the Cassini Composite Infrared Spectrometer (CIRS) and the Infrared Space Observatory Short Wavelength Spectrometer [4], and comment on the effect of spectral resolution on retrieved information content. We conclude by recommending gaps in current spectroscopic knowledge of molecular bands that could be addressed by theoretical and laboratory study to aid future astronomical studies of Titan, for example the James Webb Space Telescope (JWST) and the Stratospheric Observatory for Infrared Astronomy (SOFIA) Acknowledgments: Data analyzed in this project is public available online on the Spitzer Heritage Archive (sha.ipac.caltech.edu). This research has made use of the NASA/IPAC Infrared Science Archive, which is funded by the National Aeronautics and Space Administration and operated by the California Institute of Technology.

Titan↗

Method and apparatus for controlling mass flow rate of recycled anode tail gas in solid oxide fuel cell system

In an SOFC stack system, a reformer supplies reformate to the stack. An anode tail gas portion is recycled into the reformer. An inline flowmeter indicates an apparent recycle flow rate. A map of anode tail gas composition as a function of fuel utilization efficiency U, reformer oxygen/carbon ratio O:C, and recycle percentage R is generated on a laboratory test bed at various recycle rates and fuel utilization rates. Compositions are sent through a flowmeter and a Coriolus mass flowmeter provide a Coriolus flow and sensor voltage function across the various compositions and flow rates to create an average curve and an average (reference) voltage at a given flow. A scale factor Z is calculated and used to determine a scaled sensor voltage X for use in an average flow polynomial curve fit equation to calculate tail gas mass flow rate at any flow value indicated by the flow meter.

30 DIRECT ENERGY CONVERSION↗

Coupling reduced‐order modeling and coarse‐grained CFD‐DEM to accelerate coal gasifier simulation and optimization

Abstract High fidelity three‐dimensional (3‐D) numerical simulations of commercial‐scale coal gasifiers are very time consuming and expensive. This article proposes a reduced‐order modeling approach that uses quasi one‐dimensional (1‐D) CFD–DEM simulation results to serve as an accurate initial condition for the 3‐D simulation, which significantly shortens the physical time from several hours to minutes to achieve steady states. The 3‐D simulation employs a previously validated coarse‐grained CFD‐DEM approach, which further accelerates the simulation. Both 1‐D and 3‐D simulations adopt a particle shrinkage scheme to correctly account for the particle volume change due to chemical reaction and thus provides an accurate bed height. Comparison with available experimental measurements of the bed temperature and synthesis gas composition is used to validate the simulation. The final syngas composition and flowrates are strongly affected by the fuel or gasification agent rate and process operating conditions as expected. This approach is then used to optimize two important operating conditions (air and steam flows) to achieve specific gasifier performance goals for the production of Fischer–Tropsch synthesis gas and production of fuel gas for gas turbines.

Yu, Jia↗

A versatile system for biological and soil chemical tests on a planetary landing craft. II - Hardware development

A system has been under development which is designed to seek remotely for clues to life in planetary soil samples. The basic approach is a set of experiments, all having a common sensor, a gas analysis mass spectrometer which monitors gas composition in the head spaces above sealed, temperature controlled soil samples. Versatility is obtained with up to three preloaded, sealed fluid injector capsules for each of eleven soil test cells. Tests results with an engineering model has demonstrated performance capability of subsystem components such as soil distribution, gas sampling valves, injector mechanisms, temperature control, and test cell seal.

Martin, J. P.↗

CO2 Acquisition Membrane (CAM)

The objective of CAM is to develop, test, and analyze thin film membrane materials for separation and purification of carbon dioxide (CO2) from mixtures of gases, such as those found in the Martian atmosphere. The membranes are targeted toward In Situ Resource Utilization (ISRU) applications that will operate in extraterrestrial environments and support future unmanned and human space missions. A primary application is the Sabatier Electrolysis process that uses Mars atmosphere CO2 as raw material for producing water, oxygen, and methane for rocket fuel and habitat support. Other applications include use as an inlet filter to collect and concentrate Mars atmospheric argon and nitrogen gases for habitat pressurization, and to remove CO2 from breathing gases in Closed Environment Life Support Systems (CELSS). CAM membrane materials include crystalline faujasite (FAU) zeolite and rubbery polymers such as silicone rubber (PDMS) that have been shown in the literature and via molecular simulation to favor adsorption and permeation of CO2 over nitrogen and argon. Pure gas permeation tests using commercial PDMS membranes have shown that both CO2 permeance and the separation factor relative to other gases increase as the temperature decreases, and low (Delta)P(Sub CO2) favors higher separation factors. The ideal CO2/N2 separation factor increases from 7.5 to 17.5 as temperature decreases from 22 C to -30 C. For gas mixtures containing CO2, N2, and Ar, plasticization decreased the separation factors from 4.5 to 6 over the same temperature range. We currently synthesize and test our own Na(+) FAU zeolite membranes using standard formulations and secondary growth methods on porous alumina. Preliminary tests with a Na(+) FAU membrane at 22 C show a He/SF6 ideal separation factor of 62, exceeding the Knudsen diffusion selectivity by an order of magnitude. This shows that the membrane is relatively free from large defects and associated non-selective (viscous flow) transport mechanisms. The Membrane Test Facility (MTF) has been developed to measure membrane permeance over a wide range of temperature and pressure. The facility uses two volume compartments separated by the membrane that are instrumented to measure temperature, delta pressure across the membrane, and gas composition. A thermal shroud supports and encloses the membrane, and provides temperature control. Methods were developed to determine membrane permeance using the first order decay of the pressure difference between the sealed compartments, using the total pressure for pure gases, and partial pressure of each species in gas mixtures. The technique provides an end-to-end measurement of gas permeance that includes concentration polarization effects. Experiments have shown that in addition to membrane permeance properties, the geometry and design of associated structures play an important role in how membrane systems will function on Mars.

Mason, Larry W.↗

chapter 40 - Gasification Technologies, "Handbook of Climate Change Mitigation and Adaptation"

Gasification is an enabling technology for the clean-up of fossil and biomass fuels for energy production. A history of gasifier development is told from the perspective of a technology evolving to meet the ever changing market needs. The chemistry and physics of coal conversion includes pyrolysis, combustion, gasification, mineral transformations as well as a discussion of the materials developed to meet the most challenging gasifier applications. Integrated gasification and combined cycle processes are discussed with respect to electrical power production. The distinguishing features for different types of gasifiers are described including fixed bed, fluidized bed, entrained flow, transport gasifiers. The twelve major gasifiers being marketed today are described. The hydrodynamics and kinetics of each are reviewed along with salient differences in performance, such as gas composition, when using a variety of fuels under different conditions. Critical operational features that are discussed include oxidizing media, air or oxygen blown; the system pressure; fuel feed stock; and downstream clean-up. Thermal integration is discussed with respect to its impact on the gasifier performance. Gas clean-up is also considered with respect to the removal of potential pollutants and the shifting to environmentally benign transportation and process fuels.

01 COAL, LIGNITE, AND PEAT↗

An experimental investigation of the effectiveness of Ar-CO 2 shielding gas mixture for the wire arc additive process

Wire arc additive manufacturing (AM) is the process by which a large, metallic structure is built layer-by-layer using a welding arc to melt a wire feedstock. A novel opportunity exists to alter the shielding gas composition to fabricate distinct geometrical features without altering the other AM parameters. In this paper, shielding gases with varied concentrations of Argon (Ar) and CO 2 was used to deposit three distinct geometric shapes (walls, infill, and overhang) using a wire-based additive manufacturing system utilizing the gas metal arc welding (GMAW) surface tension transfer (STT) process. Computer-aided design (CAD) models were sliced with a custom-built slicer, and the sliced algorithm was converted into optimal robotic toolpaths. A custom virtual instrument (VI) was built in LabVIEW to compare the temperature profiles on the surface during each deposition process. After each deposition, the geometric features were scanned, and the surface waviness value was evaluated. Tensile and Charpy impact coupons were extracted from the wall geometries in the longitudinal and transverse directions and tested. The results indicated that a higher CO 2 content produced higher melt pool temperatures to an extent, while lower contents of CO 2 resulted in a dimensionally accurate geometry. The data also indicated that the 2%/98% CO 2 /Ar blend produced scatter in tensile strength and the analysis of variance (ANOVA) shows significant difference. However, the intermediate range of CO 2 (5–10%) resulted in uniform tensile properties. Altogether, these results indicate that a 5%/95% CO 2 /Ar blend is the ideal shielding gas for lowering process temperatures and improving mechanical properties in wire arc additive manufacturing using the gas metal arc welding surface tension transfer process. Additionally, varying concentrations of Ar/CO 2 can be used within the same part in order to modify the local properties or process parameters such as strength, toughness, temperature, or dimensional features. This may improve overall manufacturing quality without sacrificing specific properties.

42 ENGINEERING↗

Passive sampling and analyses of common dissolved fixed gases in groundwater

An in situ passive sampler and gas chromatographic protocol for analysis of the major and several minor fixed gases in groundwater was developed. A gas-tight syringe, mated to a short length of silicone tubing, was equilibrated with dissolved gases in groundwater by immersing in monitoring wells and was used to transport and to inject a 0.5 mL gas sample into a gas chromatograph. Using Ar carrier gas, a HaySep DB porous polymer phase, and sequential thermal conductivity and reductive gas detectors allowed good sensitivity for He, Ne, H2, N2, O2, CO, CH4, CO2, and N2O. Within 4 days of immersion in groundwater, samplers initially filled with either He or air attained the same and constant gas composition at an Oak Ridge, Tennessee, site heavily impacted by uranium, acidity, and nitrate. Between June 2006 and July 2007, 12 permanent groundwater wells were used to test the passive samplers in groundwater contaminated by a group of four closed radioactive wastewater seepage ponds; over a thousand passive gas samples from these wells averaged 56% CO2, 32.4% N2, 2.5% O2, 2.5% N2O, 0.20% CH4, 0.096% H2, and 0.023% CO with an average recovery of 95 14% of the injected gas volume.

54 ENVIRONMENTAL SCIENCES↗

Evaluation of catalytic combustion of actual coal-derived gas

The combustion characteristics of a Pt-Pl catalytic reactor burning coal-derived, low-Btu gas were investigated. A large matrix of test conditions was explored involving variations in fuel/air inlet temperature and velocity, reactor pressure, and combustor exit temperature. Other data recorded included fuel gas composition, reactor temperatures, and exhaust emissions. Operating experience with the reactor was satisfactory. Combustion efficiencies were quite high (over 95 percent) over most of the operating range. Emissions of NOx were quite high (up to 500 ppm V and greater), owing to the high ammonia content of the fuel gas.

Blanton, J. C.↗

Expansion dynamics of femtosecond laser-induced plasmas: Influence of thermophysical plasma properties

This study investigates the expansion dynamics of femtosecond laser-induced plasmas, emphasizing the impact of plasma thermophysical properties and ambient gas composition. Through shadowgraphy experiments and multiphase computational fluid dynamics (CFD) simulations, the influence of parameters such as heat capacity, molecular weight, and thermal conductivity on plume morphology, shockwave evolution, and energy dissipation mechanisms is examined. A mixture multiphase model is implemented to capture the interaction between the plasma and the surrounding gas. Simulation results reveal that plasma expansion is strongly inertia-driven. Results show that differences in plasma properties and ambient conditions affect the shape and temperature distribution of the expanding plume. The early-stage dynamics are primarily dictated by pressure forces, whereas thermal and viscous effects play a growing role in the plume's behavior during later stages of expansion. The CFD findings show the necessity of accurate initial condition characterization, including crater geometry and plasma pressure and temperature, for reliable modeling of plasma evolution in laser ablation processes.

CFD modeling↗