Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel cell technologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Techno-Economic Analysis of Integrated Gasification Fuel Cell Systems

This is a presentation that was delivered virtually at the 2020 International Pittsburgh Coal Conference. In the presentation, details of the cost and performance parameter improvement due to incremental changes made in gasification and fuel cell operation and system configurations were presented. High level results indicate that SOFC fueled by coal-derived synthesis gas can be competitive with other fossil-based energy generation technologies when significant improvement to gasification technology is made and carbon capture is included. The cost of carbon capture of this system is very low due to the high efficiency of the SOFC and the high system fuel utilization due to the vent gas recirculation concept which recirculates hydrogen in the effluent back to the cell.

Noring, Alex↗
DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗
DOE OSTI2022

BISON Validation to In-Situ Cladding Burst Test and High Burnup LOCA Experiments

The process to develop and qualify nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and post irradiation examinations (PIEs); and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes approximately 20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long and drawn-out process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in-situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In general, the in-situ measurements provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the United States nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the Nuclear Regulatory Commission, through their research information letter, outlined a number of technical issues for the industry to address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heatup phase. Leveraging these advanced in-situ capabilities, this work intends to use insitu data generated from a simulated LOCA in the Severe Accident Test Station at Oak Ridge National Laboratory to better understand high-temperature creep and its impact on Zircaloy balloon and rupture performance. This work used the BISON fuel performance code to compare BISON’s high-temperature creep model predictions to in-situ data and identify limitations and gaps within the model. Additionally, BISON will subsequently be used to simulate relevant high-burnup LOCA tests. The results will be analyzed and compared to the available post-test data in a manner consistent with the approach outlined in the Nuclear Regulatory Commission research information letter.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Final Technical Report

The Department of Energy is interested in technologies that support the sustainable production of fuels, chemicals, and other bioproducts from plant biomass, to offset the nation’s reliance on fossil resources. The plant cell wall of energy crops provides the largest reservoir of raw materials for bioproducts. However, the widespread use of plant cell walls is hampered by their complexity and resistance to breakdown. To improve the productivity and cost-effectiveness of using energy crops to generate bioproducts, the fundamental problem of deconstructing plant cell walls must be addressed. This project developed and evaluated an innovative genetic modification technology to produce strategically designed enzymes that specifically accumulate in the plant cell wall. The resulting enzyme-engineered energy crops are expected to grow normally under natural conditions but break down more quickly and easily under high temperature during the production of biobased products. As such, this plant cell wall targeting enzyme engineering effort will reduce the cost of plant cell wall deconstruction and ultimately improve the economics of bioproducts. The overall objective of this project is to develop and evaluate the in-planta enzyme engineering technology to reduce lignocellulose deconstruction cost. The concept was first validated using tobacco plant, a model plant system that is typically used in lab testing for initial concept validation. Then the enzyme optimization was validated using switchgrass, the energy crop to be used to produce bioproducts. There are three specific objectives in this Phase I project: (1) validate the enzyme optimization concept using tobacco plant, a model plant system. (2) validate the enzyme optimization concept using switchgrass. (3) techno-economic analysis (TEA) for further scale-up application. By the end of this project, in-planta enzyme engineering was validated in both tobacco and switchgrass plants, with improved enzyme activity and saccharification efficiency. The in-planta enzyme engineering in Tabacco didn’t have a significant impact on plant growth and development. Transgenic tobacco plants with in-planta cellulose degrading enzymes showed higher biomass digestibility than wild type. Gene construction and transformation in switchgrass was much longer than expected, which delayed the research progress. Besides, in-planta engineering of lignin degrading enzyme is more challenging than cellulose degrading enzyme, in terms of expression detection. Expression of lignin degrading enzyme and cellulose degrading enzyme improved biomass yield and saccharification efficiency of switchgrass, respectively. It is promising to express both genes in switchgrass for optimized overall performance. According to the results of TEA, switchgrass biomass production cost is mainly attributed to by fertility and harvesting. Biomass production profit can increase up to 10-fold depending on biomass price. The PHA production profit is also sensitive to the biomass price. The proposed technology could potentially reduce the biomass deconstruction cost from 33% to 9% of PHA revenue, making the biomass-based PHA competitive to petroleum-based polymers even in case of relatively high biomass price of biomass. Therefore, cultivation of the genetically engineered self-deconstruction switchgrass for Polyhydroxyalkanoate (PHA) production could benefit switchgrass grower and PHA producer with attractive profits for both sectors. This new enzyme optimization approach will be beneficial for bioindustries that use energy crops as feedstocks. It will improve the economic viability of converting energy crops to renewable products that support a sustainable society and helps address the Nation’s long-term strategic needs for renewable products and reduction of reliance on fossil resources.

42 ENGINEERING↗
DOE OSTI2024

Kinetic Plasma Simulation in the MOOSE Framework: Verification of Electrostatic Particle In Cell Capabilities

In magnetic confinement nuclear fusion reactors, the interaction between the plasma edge and plasma facing components is extremely important. At the plasma edge, a kinetic representation such as particle-in-cell (rather than a fluid representation) is required to accurately capture the plasma behavior. General purpose particle-in-cell plasma simulation capabilities have been developed in the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. This new capability is a part of the development of a new MOOSE-based framework for modeling plasma facing components, the Fusion ENergy Integrated multiphys-X (FENIX) framework. In this work, the verification of foundational particle-in-cell capabilities in FENIX is presented. This new plasma simulation capability has three main components: moving particles in discrete steps on the finite element mesh, mapping charge density from the particle's location to the finite element mesh, and solving for the electrostatic potential based on the charge density mapped from particles to the mesh. In this paper, simple verification problems demonstrating each of these new capabilities are presented, and future work includes electromagnetic capabilities and Monte Carlo collisions with neutral gas particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Sustainable Port Operations: Powered by NREL

Seaports are vital economic hubs that allow the United States to compete on a global scale. But the heavy vehicles and cargo equipment that enable their operations also emit harmful air pollutants and greenhouse gas emissions. For nearly two decades, National Renewable Energy Laboratory (NREL) researchers have worked toward comprehensive seaport decarbonization. They fuse world-class analysis with deep vehicle and transportation systems knowledge to guide strategic deployment of low- and zero-emissions vehicles, charging and refueling infrastructure, and grid improvements. Together, these capabilities can enable sustainable port operations. This fact sheet outlines major seaport and airport decarbonization capabilities across the laboratory, including: fleet research, energy data, and insights for decarbonization; comprehensive hydrogen infrastructure deployment; optimized charging through grid integration; strategic blueprinting for clean, optimized technology deployment; and integrating diversity, equity, inclusion, and accessibility considerations into decarbonization efforts.

ADVANCED PROPULSION SYSTEMS,ENERGY CONSERVATION, C↗
DOE OSTI2023

Boosting the performance of reversible solid oxide electrochemical cells with a novel hybrid oxygen electrode, Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ

Solid oxide electrochemical cells (SOECs) stand out as a highly promising clean energy technology that offers several benefits, showing significant potential to play a pivotal role in the transition towards a sustainable and low-carbon energy future. SOECs can efficiently convert the chemical energy stored in fuels to electricity in fuel cell mode, and produce various chemicals from abundant feedstocks (e.g., CO 2 , H 2 O) and intermittent solar/wind-based renewable electricity. Despite extensive efforts that have been devoted to designing novel materials and optimizing SOEC manufacturing processes, aiming to achieve enhanced energy efficiency, the current SOECs still suffer from poor performance, which is mainly due to the sluggish oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics. To address this challenge, in this work, we have successfully designed an in situ formed hybrid oxygen electrode material (Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ ), which significantly improves the surface oxygen exchange coefficient and bulk oxygen-ion diffusion coefficient, enhancing the OER and ORR electrocatalytic activities. Further, the SOECs equipped with this newly developed oxygen electrode achieved exceptional performance for power generation using both hydrogen and propane as the fuels. At 750 °C, a peak power density of 2.4 W cm -2 was obtained with H 2 as the fuel. Additionally, the SOECs attain unprecedented performance in steam electrolysis mode. A current density of 4.4 A cm -2 was achieved at 1.3 V and 750 °C, which represents the highest performance among all yttria-stabilized zirconia (YSZ) electrolyte-based SOECs. The SOECs also deliver remarkable stability during the accelerated stability testing, highlighting the great potential of Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ as a high-performance oxygen electrode for next generation SOECs.

08 HYDROGEN↗
DOE OSTI2022

New challenges in oxygen reduction catalysis: a consortium retrospective to inform future research

In this perspective, we highlight results of a research consortium devoted to advancing understanding of oxygen reduction reaction (ORR) catalysis as a means to inform fuel cell science. We demonstrate how targeted collaborations between different institutions from academic, national lab, and industry backgrounds and different scientific disciplines like theory, experiment, and characterization can yield unique insights into fuel cell catalysts. We comment on such insights into material designs for platinum-group-metal alloys, transition metal oxides, and non-traditional materials including metal–organic frameworks; systems that have served as the foundational building blocks for our consortium. We also motivate a renewed focus on catalyst durability in light of emerging technological requirements and paths forward in understanding in situ and operando electrochemical stability. Lastly, we describe new frontiers ORR research can take and how emerging artificial intelligence tools can assist researchers in capturing data, selecting new experiments, and guiding characterization to accelerate the design and discovery of fuel cell catalysts. A main goal of sharing this perspective is to discuss the rationale for our future research plans based on our consortium work. However, we also hope to illustrate both the potential impact of a collaborative strategy with the hopes of inspiring a higher degree of Industry-Academia-National Laboratory collaboration and encourage other centers and consortiums to distill and share their findings in a similar perspective-type article. Together we hope to enable the fuel cell research community to engage in a discussion of strategies for research and accelerated development of catalysts with improved activity and stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Techno-economic comparison of electrification for heavy-duty trucks in China by 2040

We show that electrification of heavy-duty trucks (HDTs) is critical of achieving sustainability and carbon neutrality in road freight. Based on the total cost of ownership and the life-cycle emissions, the study compared the traditional diesel internal combustion engine vehicle technologies with potential electrification options for HDTs in China, including battery electric vehicle, plug-in hybrid electric vehicle, hydrogen fuel cell vehicle, and battery electric catenary vehicle. Scenario and sensitivity analysis were explored the life-cycle effects of these electrification options in China from 2020 to 2040. It is found that green electricity and green hydrogen are the most important factors influencing the life-cycle emissions of CO 2 , NO X , and PM 2.5 for different HDTs’ electrification options. The plug-in hybrid electric vehicle of HDTs has shown good performance in terms of total cost and carbon emissions, mainly due to the reduced battery capacity and the current grid mix in China.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Understanding the structure and composition of recalcitrant oligosaccharides in hydrolysate using high-throughput biotin-based glycome profiling and mass spectrometry

Novel Immunological and Mass Spectrometry Methods for Comprehensive Analysis of Recalcitrant Oligosaccharides in AFEX Pretreated Corn Stover. Lignocellulosic biomass is a sustainable alternative to fossil fuel and is extensively used for developing bio-based technologies to produce products such as food, feed, fuel, and chemicals. The key to these technologies is to develop cost competitive processes to convert complex carbohydrates present in plant cell wall to simple sugars such as glucose, xylose, and arabinose. Since lignocellulosic biomass is highly recalcitrant, it must undergo a combination of thermochemical treatment such as Ammonia Fiber Expansion (AFEX), dilute acid (DA), Ionic Liquid (IL) and biological treatment such as enzyme hydrolysis and microbial fermentation to produce desired products. However, when using commercial fungal enzymes during hydrolysis, only 75–85% of the soluble sugars generated are monomeric sugars, while the remaining 15–25% are soluble recalcitrant oligosaccharides that cannot be easily utilized by microorganisms. Previously, we successfully separated and purified the soluble recalcitrant oligosaccharides using a combination of charcoal and celite-based separation followed by size exclusion chromatography and studies their inhibitory properties on enzymes. We discovered that the oligosaccharides with higher degree of polymerization (DP) containing methylated uronic acid substitutions were more recalcitrant towards commercial enzyme mixtures than lower DP and neutral oligosaccharides. Here, we report the use of several complementary techniques that include glycome profiling using plant biomass glycan specific monoclonal antibodies (mAbs) to characterize sugar linkages in plant cell walls and enzymatic hydrolysate, matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF-MS) using structurally-informative diagnostic peaks offered by negative ion post-secondary decay spectra, gas chromatography followed by mass spectrometry (GC–MS) to characterize oligosaccharide sugar linkages with and without derivatization. Since oligosaccharides (DP 4–20) are small, it is challenging to mobilize these molecules for mAbs binding and characterization. To overcome this problem, we have applied a new biotin-coupling based oligosaccharide immobilization method that successfully tagged most of the low DP soluble oligosaccharides on to a micro-plate surface followed by specific linkage analysis using mAbs in a high-throughput system. This new approach will help develop more advanced versions of future high throughput glycome profiling methods that can be used to separate and characterize oligosaccharides present in biomarkers for diagnostic applications.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Roadmap on advanced and / real-time characterisation of solid state materials and devices for energy applications

A strong societal and political drive is motivating the development and optimization of novel energy conversion and storage systems for decarbonization. The successful implementation of solid state devices such as fuel cells and secondary batteries depends, however, on achieving ambitious targets in terms of performance, reliability and cost competitiveness. Research and technology are addressing these needs through a holistic approach including exploration of new materials and nanoarchitectures, as well as system engineering. These significant efforts require the support of appropriate characterization tools capable of assessing nanometer-scale phenomena such as concentration profiles of ionic and electronic charges, local chemical compositions and their evolution over time across interfaces. This roadmap provides an overview of selected advanced characterization techniques for energy materials and devices. Specific focus is put on in situ/operando methods for probing electrochemical phenomena in real-time under realistic working conditions. Experts in the field provide an extensive review of the current state of the art in 2025 and the current and future challenges for the characterization of local chemistry and kinetics in the bulk of the material, in nanoarchitectures (e.g. thin films) and at the interfaces (e.g. grain boundaries, phase contacts, solid/liquid and solid/gas interfaces) . The aim is to provide a detailed guide to the techniques, describing opportunities and bottlenecks for their practical deployment and examples of successful applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Total cost of ownership of vehicle electrification and fuel switching options for light-duty and heavy-duty vehicles

Projecting the transition from combustion engines to battery-based powertrains is complex becuase it involves numerous interdependent decisions. This study estimates total cost of ownership (TCO) to assess the economic viability of powertrain electrification, focusing exclusively on advances in vehicle and fuel technologies. Under two bounding technology-progress scenarios, we develop vehicle designs and fuel cost trajectories, which serve as inputs to TCO projections for selected classes from 2021 to 2050. We analyzed a small sport utility vehicle (SUV) to represent the light-duty vehicle (LDV) sector, and four medium- and heavy-duty vehicle (MHDV) classes: Class 6 box delivery, Class 8 drayage, Class 8 long-haul, and Class 8 transit bus. For each class, we compared the TCO of battery electric vehicles (BEVs) and fuel cell hybrid electric vehicles (FCHEVs) against conventional internal combustion engine vehicles (ICEVs). The results show that modern ICEVs generally have lower TCO; however, BEVs and FCHEVs could match or have lower TCOs than ICEVs over time, depending on technological progress. In LDVs, BEV300 is projected to deliver the lowest TCO by 2050, particularly under the high-progress scenario. In MHDVs, both BEVs and FCHEVs could become more cost-competitive than ICEVs by 2050 in the high-progress case. Beyond these results, the findings suggest further investigation is warranted for BEV charging infrastructure, FCHEV hydrogen refueling infrastructure, and MHDV charging strategies. In conclusion, these factors could reduce the fuel-cost share of TCO and enhance the competitiveness of BEVs and FCHEVs relative to ICEVs.

Battery electric vehicle↗
DOE OSTI2022

Innovative Proton Conductive Membranes Based on Two-Dimensional Materials

The team of Oak Ridge National Laboratory, New Mexico State University, and General Graphene Corporation staff will develop and commercialize paradigm-shifting low-cost, high-performing, proton-conductive membranes made from abundant and durable 2D materials. Proposed membranes are expected to be an order of magnitude better in performance and cost compared with the current state-of-the-art formulation, Nafion, and thus are expected to eliminate huge roadblocks in proliferation of fuel cells and flow batteries. The major goal for this work is to develop a fundamentally new learning curve for novel proton exchange membranes needed for various applications. The new technology will overcome the shortcomings of the current state-of-the-art membranes that are based upon Nafion polymer by offering higher proton conductivities, the ability to operate at much lower external humidity levels and higher temperatures (>120°C), and negligible fuel and oxidant crossover through the membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Load following power generation and power storage using REP and PEM technology

A hydrogen generation system for generating hydrogen and electrical power includes a power supply, a reformer-electrolyzer-purifier (REP) assembly including at least one fuel cell including an anode and a cathode separated by an electrolyte matrix, at least one low temperature fuel cell, and a hydrogen storage. The at least one fuel cell is configured to receive a reverse voltage supplied by the power supply and generate hydrogen-containing gas in the anode of the at least one fuel cell. The at least one low temperature fuel cell is configured to receive the hydrogen-containing gas output from the REP assembly. The at least one low temperature fuel cell is configured to selectably operate in a power generation mode in which the hydrogen-containing gas is used to generate electrical power and a power storage mode in which the hydrogen-containing gas is pressurized and stored in the hydrogen storage.

Jahnke, Fred C.↗
DOE OSTI2025

Voltage cycling as a dynamic operation mode for high temperature electrolysis solid oxide cells

Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for the efficient production of H2 via high-temperature electrolysis. However, power input from dynamic energy sources remains a significant challenge for their long-term stability. It is important to analyze the tolerance of cells under dynamic operation conditions. This study focuses on evaluating the impact of voltage cycling on the performance and durability of electrode-supported SOECs. We explore the operational limits and degradation mechanisms of SOECs subjected to various voltage conditions and find that the cells have high tolerance for dynamic voltage. Voltage cycling between 1.3 V and 1.5 V for 9000 cycles does not damage the cell. Conversely, cycling to higher voltages (≥1.7 V) results in accelerated degradation. Advanced characterization is used to screen for various degradation modes post operation. Within the oxygen electrode, XRD and STEM EDS find compositional and phase evolution in all voltage cycled samples including increased decomposition of the air electrode resulting in cation migration. Microstructural analysis of the fuel electrode from nano-CT data shows minimal change throughout the sample set and no evidence of Ni migration, indicating the fuel electrode is stable and not impacted by cycling to higher voltages within the timeframe studied.

Zhu, Zhikuan↗
DOE OSTI2025

Multimodal In Situ Characterization Uncovers Unexpected Stability of a Cobalt Electrocatalyst for Acidic Sustainable Energy Technologies

An accelerated development of durable and affordable sustainable energy technologies is often hindered by a limited understanding of how non-precious materials within these systems degrade. In acidic proton exchange membrane fuel cells and water electrolyzers, metallic cobalt (Co) is considered an unstable component that is often combined with precious metals or other stabilizers. To understand the mechanisms behind Co instability, we employ an experimental platform that quantifies dissolution with on-line inductively coupled plasma mass spectrometry and product formation with electrochemical mass spectrometry during electrochemical testing, along with ex- situ characterization. Under varied conditions (electrocatalysis, time, gas-type saturation, and ion concentration), windows of Co stability are observed that are different than predicted with classical chemical thermodynamics, suggesting new stabilization and degradation mechanisms than previously understood. Notably, Co is active for the hydrogen evolution reaction (HER), with prolonged stability that is ~300 mV different than thermodynamically projected. Additionally, in an oxygenated environment, Co concurrently performs the HER and oxygen reduction reaction (ORR) yet undergoes different morphology changes and dissolution mechanisms. Interestingly, in the absence of electrocatalysis, there is a 22x decrease in dissolution in an oxygen-free environment, proposing a route to decrease Co losses during device shutdown protocols. Lastly, under more extreme operating conditions, Co becomes stable after a substantial amount of dissolution, suggesting that high concentrations of Co 2+ ions in the microenvironment induce the formation of a stable CoHO 2 surface. Altogether, these results can be leveraged to improve the design and development of more robust and cost-effective sustainable energy technologies, as well as promote strategic strategies for prolonged material utilization.

Dissolution↗
DOE OSTI2022

Laser diagnostics to characterize the in-flame growth of platinum nanoparticles manufactured by the reactive spray deposition technology

Reactive Spray Deposition Technology (RSDT) is an atmospheric pressure, flame-based advanced manufacturing method used to fabricate Membrane Electrode Assemblies (MEAs) for proton exchange fuel cells and water electrolyzers. RSDT combines the flame synthesis of catalyst nanoparticles and their deposition onto the membrane in one step. The properties of the synthesized nanoparticles, such as their Size Distribution Function (SDF), determine the manufactured electrodes’ performance, which can be evaluated when the deposition is complete via ex-situ characterization of the products. Efforts to improve RSDT for manufacturing state-of-the-art MEAs can be significantly enhanced with integrated laser diagnostics that enable in situ measurement of the synthesized catalyst nanoparticles. This paper reports the implementation of laser diagnostics in an RSDT facility and evaluates their potential to assist the manufacturing process. Laser Light Scattering (LS) and Laser-Induced Incandescence (LII) measurements are performed in the oxygen-rich zone of the flame at various distances from the flame fuel jet nozzle downstream of its luminous region. The measurements quantitatively track the evolution in size and volume fraction of platinum-based nanoparticles in two flames that yield different catalytic properties in the manufactured electrodes. The profiles of the measured nanoparticles’ volume fraction along the flame axis can be estimated a priori so that the average nanoparticle sizes can be measured in quasi-real time via LS. Nanoparticles experience an extremely slow growth rate while being convected at distances from 150 nm to 300 nm from the fuel nozzle. Complementary characterizations of the synthesized nanoparticles are performed ex-situ via High-Angle Annular Darkfield Scanning Transmission Electron Microscopy (HAADF-STEM) image analyses of samples collected on grids at a fixed distance from the fuel jet nozzle. Comparing the results from laser and microscopy techniques not only cross-validates the findings but also provides the parameters to infer the bimodal SDF in-situ and yields evidence that the coagulation efficiency of the synthesized nanoparticles has extremely low values in the investigated zone of the flames.

Rayleigh Light Scattering (LS)↗
DOE OSTI2023

Status Update on NETL Techno-Economic Analysis of Solid Oxide Cells

This is a presentation delivered at the Solid Oxide Fuel Cell Project Review Meeting portion of the 2023 FECM / NETL Spring R&D Project Review Meeting on April 19, 2023. The presentation highlights recently completed techno-economic analysis of solid oxide cell systems including a brief overview of pairing SOFC technology with energy storage, an analysis of the tradeoffs associated with reversible SOC technology versus paired SOFC/SOEC, and highlights of the recently released NGFC and IGFC pathway studies. A more detailed description of analysis conducted on hydrogen fueled SOFC systems is also included.

Hackett, Gregory↗