Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fluid jets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

CFD analysis of jet mixing in low NO(x) flametube combustors

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor has been identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3D CFD analyses for optimizing jet mixing was demonstrated.

Talpallikar, M. V.↗
NASA NTRS1994

Analysis of tangential slot blowing on F/A-18 isolated forebody

Generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and under-blowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind tunnel and sub-scale wind tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Gee, K.↗
NASA NTRS1995

Analysis of Tangential Slot Blowing on F/A-18 Isolated Forebody

The generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and underblowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind-tunnel and subscale wind-tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flowfield about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Gee, Ken↗
NASA NTRS1998

Injector Design Tool Improvements: User's manual for FDNS V.4.5

The major emphasis of the current effort is in the development and validation of an efficient parallel machine computational model, based on the FDNS code, to analyze the fluid dynamics of a wide variety of liquid jet configurations for general liquid rocket engine injection system applications. This model includes physical models for droplet atomization, breakup/coalescence, evaporation, turbulence mixing and gas-phase combustion. Benchmark validation cases for liquid rocket engine chamber combustion conditions will be performed for model validation purpose. Test cases may include shear coaxial, swirl coaxial and impinging injection systems with combinations LOXIH2 or LOXISP-1 propellant injector elements used in rocket engine designs. As a final goal of this project, a well tested parallel CFD performance methodology together with a user's operation description in a final technical report will be reported at the end of the proposed research effort.

Chen, Yen-Sen↗
DOE OSTI2020

Additive Manufacturing Interface Profiles for Jet Studies on the Vertical Shock Tube

Understanding the mixing between two fluids of disparate densities (i.e., variable density mixing) is important for the lab's mission. Experiments are required to validate our codes, such as RAGE, FLAG, and the BHR mix model. The role initial conditions (ICs) have on instability growth and the transition to turbulence is not completely understood and comparisons with experiments are needed. The Extreme Fluids team focuses on experiments at Los Alamos that utilize gases and low shock velocities (Mach <2 in air). These experiments have the advantage of high fidelity diagnostics capable of temporally and spatially resolved velocity and density measurements. One main difficulty is setting up a specific interface profile between the two gases. While attempts have been made to do so without the aid of a solid structure (i.e., a membrane), the results are limited in the range of possible shapes and reproducibility. Membranes provide the best way to provide a deterministic initial condition. However, fragments from the membrane can interfere with the flow and instability growth, as well as the diagnostics. In this project, we focused on exploring the materials and techniques available via modern additive manufacturing (i.e., 3D printing) to test if they could address some of the shortcomings of prior membrane designs. Our goal was to find a material that would have minimal impact on our experiment while also providing us with a means to produce complex initial conditions. This report details our work to explore the range of additive manufacturing capabilities and the jet-like structures we were able to generate using three-dimensional initial conditions.

36 MATERIALS SCIENCE↗
NASA NTRS1991

CFD analysis of jet mixing in low NOx flametube combustors

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor was identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3-D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3-D CFD analyses for optimizing jet mixing was demonstrated.

Talpallikar, M. V.↗
NASA NTRS2012

On Laminar to Turbulent Transition of Arc-Jet Flow in the NASA Ames Panel Test Facility

This paper provides experimental evidence and supporting computational analysis to characterize the laminar to turbulent flow transition in a high enthalpy arc-jet facility at NASA Ames Research Center. The arc-jet test data obtained in the 20 MW Panel Test Facility include measurements of surface pressure and heat flux on a water-cooled calibration plate, and measurements of surface temperature on a reaction-cured glass coated tile plate. Computational fluid dynamics simulations are performed to characterize the arc-jet test environment and estimate its parameters consistent with the facility and calibration measurements. The present analysis comprises simulations of the nonequilibrium flowfield in the facility nozzle, test box, and flowfield over test articles. Both laminar and turbulent simulations are performed, and the computed results are compared with the experimental measurements, including Stanton number dependence on Reynolds number. Comparisons of computed and measured surface heat fluxes (and temperatures), along with the accompanying analysis, confirm that that the boundary layer in the Panel Test Facility flow is transitional at certain archeater conditions.

Gokcen, Tahir↗
DOE OSTI2023

Bayesian Parameter Estimation of the k-ω Shear Stress Transport Model for Accurate Simulations of Impinging-Jet Heat Transfer

Given the lack of fusion-relevant component test facilities, current estimates of the thermo-fluid performance of plasma-facing components are based for the most part on numerical simulations. A major source of uncertainty in these simulations is the semiempirical turbulence (closure) models for the Reynolds stresses appearing in the governing Reynolds-averaged Navier-Stokes equations, which involve a set of constants that depend upon the flow. The objective of this study is to evaluate Bayesian parameter estimation of turbulence closure constants in ANSYS Fluent to model heat transfer in impinging jets. The Bayesian statistical calibration produces a probability distribution for these constants from experimental data; the maximum a posteriori estimates are then taken to be the calibrated constants, or parameters. The turbulence model constants are calibrated using an experimental study of a submerged jet of air impinging on a flat heated surface at Reynolds numbers Re = O(10 4 ) and impingement distance in jet diameters H/d = 2. Numerical predictions using the calibrated model parameters are then compared with those generated using the default constants. Predictions obtained with model parameters calibrated on datasets of two different sizes are compared to evaluate the effect of the number of calibration samples. Lastly, the extrapolative ability of the calibrated model is examined by predictions at a Re beyond the calibration values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

One-dimensional temperature measurement of supersonic jet flow by resonantly ionized photoemission thermometry of molecular nitrogen

As the field of fluid dynamics progresses, the demand for sophisticated diagnostic methods to accurately assess flow conditions rises. In this work, resonantly ionized photoemission thermometry (RIPT) has been used to directly target and ionize diatomic nitrogen (N 2 ) to measure one-dimensional (1D) temperature profiles in a supersonic jet flow. This technique can be considered non-intrusive as the premise uses resonantly enhanced multiphoton ionization (REMPI) to target molecular nitrogen. This resonance excites N 2 into absorption bands of the P, Q, and R rotational branches of N 2 ( b 1 Π u ). The ideal (3 + 1) REMPI scheme excites from the ground state and ionizes N 2 ( b 1 Π u ← X 1 Σ g + ) where de-excitation results in photoemission from the first negative band of ionized N 2 + ( B 2 Σ u + → X 2 Σ g + ) as nitrogen returns to the ground state. The resulting emission can be observed using an intensified camera, thus permitting inference of the rotational temperature of ground-state molecular nitrogen. A linearly regressive Boltzmann distribution is applied based on previous calibration data for this technique to quantify the temperature along the ionized line. This work applies this technique to a pure N 2 supersonic jet in cross-flow and counter-flow orientations to demonstrate N 2 RIPT’s applications in a supersonic flow. Temperature variations are observed at different locations downstream of the exit in cross-flow, and axisymmetric in counter-flow, to generate profiles characterizing the flow dynamics. Due to the collisional effects resulting from the number density of N 2 at higher pressures, a (3 + 2) REMPI scheme is observed throughout this text.

Clark, Aleksander (ORCID:0009000855600042)↗
NASA NTRS1987

A computational study of thrust augmenting ejectors based on a viscous-inviscid approach

A viscous-inviscid interaction technique is advocated as both an efficient and accurate means of predicting the performance of two-dimensional thrust augmenting ejectors. The flow field is subdivided into a viscous region that contains the turbulent jet and an inviscid region that contains the ambient fluid drawn into the device. The inviscid region is computed with a higher-order panel method, while an integral method is used for the description of the viscous part. The strong viscous-inviscid interaction present within the ejector is simulated in an iterative process where the two regions influence each other en route to a converged solution. The model is applied to a variety of parametric and optimization studies involving ejectors having either one or two primary jets. The effects of nozzle placement, inlet and diffuser shape, free stream speed, and ejector length are investigated. The inlet shape for single jet ejectors is optimized for various free stream speeds and Reynolds numbers. Optimal nozzle tilt and location are identified for various dual-ejector configurations.

Lund, Thomas S.↗
NASA NTRS2006

Analysis of a Cylindrical Specimen Heated by an Impinging Hot Hydrogen Jet

A computational conjugate heat transfer methodology was developed, as a first step towards an efficient and accurate multiphysics, thermo-fluid computational methodology to predict environments for hypothetical solid-core, nuclear thermal engine thrust chamber and components. A solid conduction heat transfer procedure was implemented onto a pressure-based, multidimensional, finite-volume, turbulent, chemically reacting, thermally radiating, and unstructured grid computational fluid dynamics formulation. The conjugate heat transfer of a cylindrical material specimen heated by an impinging hot hydrogen jet inside an enclosed test fixture was simulated and analyzed. The solid conduction heat transfer procedure was anchored with a standard solid heat transfer code. Transient analyses were then performed with ,variable thermal conductivities representing three composites of a material utilized as flow element in a legacy engine test. It was found that material thermal conductivity strongly influences the transient heat conduction characteristics. In addition, it was observed that high thermal gradient occur inside the cylindrical specimen during an impulsive or a 10 s ramp start sequence, but not during steady-state operations.

Wang, Ten-See↗
NASA NTRS1997

The Stability of Radiatively Cooling Jets I. Linear Analysis

The results of a spatial stability analysis of a two-dimensional slab jet, in which optically thin radiative cooling is dynamically important, are presented. We study both magnetized and unmagnetized jets at external Mach numbers of 5 and 20. We model the cooling rate by using two different cooling curves: one appropriate to interstellar gas, and the other to photoionized gas of reduced metallicity. Thus, our results will be applicable to both protostellar (Herbig-Haro) jets and optical jets from active galactic nuclei. We present analytical solutions to the dispersion relations in useful limits and solve the dispersion relations numerically over a broad range of perturbation frequencies. We find that the growth rates and wavelengths of the unstable Kelvin-Helmholtz (K-H) modes are significantly different from the adiabatic limit, and that the form of the cooling function strongly affects the results. In particular, if the cooling curve is a steep function of temperature in the neighborhood of the equilibrium state, then the growth of K-H modes is reduced relative to the adiabatic jet. On the other hand, if the cooling curve is a shallow function of temperature, then the growth of K-H modes can be enhanced relative to the adiabatic jet by the increase in cooling relative to heating in overdense regions. Inclusion of a dynamically important magnetic field does not strongly modify the important differences between an adiabatic jet and a cooling jet, provided the jet is highly supermagnetosonic and not magnetic pressure-dominated. In the latter case, the unstable modes behave more like the transmagnetosonic magnetic pressure-dominated adiabatic limit. We also plot fluid displacement surfaces associated with the various waves in a cooling jet in order to predict the structures that might arise in the nonlinear regime. This analysis predicts that low-frequency surface waves and the lowest order body modes will be the most effective at producing observable features in the jet.

Hardee, Philip E.↗
NASA NTRS2001

Prediction of Business Jet Airloads Using The Overflow Navier-Stokes Code

The objective of this work is to evaluate the application of Navier-Stokes computational fluid dynamics technology, for the purpose of predicting off-design condition airloads on a business jet configuration in the transonic regime. The NASA Navier-Stokes flow solver OVERFLOW with Chimera overset grid capability, availability of several numerical schemes and convergence acceleration techniques was selected for this work. A set of scripts which have been compiled to reduce the time required for the grid generation process are described. Several turbulence models are evaluated in the presence of separated flow regions on the wing. Computed results are compared to available wind tunnel data for two Mach numbers and a range of angles-of-attack. Comparisons of wing surface pressure from numerical simulation and wind tunnel measurements show good agreement up to fairly high angles-of-attack.

Bounajem, Elias↗
NASA NTRS1976

Study of liquid jet impingement on screens

A model is presented for an unconfined flow, such as a free jet, impinging on a screen which incorporates the influence of liquid deflection by the screen. The boundary layer blockage coefficient is introduced. This coefficient depends on the screen weave geometry and the jet impingement angle, and essentially accounts for the increase in fluid particle trajectory length through the screen resulting from the flow deflection. Comparisons were made with previous experimental studies to determine empirical values of the blockage coefficient. It is concluded that the new model reliably predicts the bulk flow and penetration characteristics of an impinging liquid jet interacting with a screen.

Dodge, F. T.↗
NASA NTRS2010

Advancements in Dual-Pump Broadband CARS for Supersonic Combustion Measurements

Space- and time-resolved measurements of temperature and species mole fractions of nitrogen, oxygen, and hydrogen were obtained with a dual-pump coherent anti-Stokes Raman spectroscopy (CARS) system in hydrogen-fueled supersonic combustion free jet flows. These measurements were taken to provide time-resolved fluid properties of turbulent supersonic combustion for use in the creation and verification of computational fluid dynamic (CFD) models. CFD models of turbulent supersonic combustion flow currently facilitate the design of air-breathing supersonic combustion ramjet (scramjet) engines. Measurements were made in supersonic axi-symmetric free jets of two scales. First, the measurement system was tested in a laboratory environment using a laboratory-scale burner (approx.10 mm at nozzle exit). The flow structures of the laboratory-burner were too small to be resolved with the CARS measurements volume, but the composition and temperature of the jet allowed the performance of the system to be evaluated. Subsequently, the system was tested in a burner that was approximately 6 times larger, whose length scales are better resolved by the CARS measurement volume. During both these measurements, weaknesses of the CARS system, such as sensitivity to vibrations and beam steering and inability to measure temperature or species concentrations in hydrogen fuel injection regions were indentified. Solutions were then implemented in improved CARS systems. One of these improved systems is a dual-pump broadband CARS technique called, Width Increased Dual-pump Enhanced CARS (WIDECARS). The two lowest rotational energy levels of hydrogen detectable by WIDECARS are H2 S(3) and H2 S(4). The detection of these lines gives the system the capability to measure temperature and species concentrations in regions of the flow containing pure hydrogen fuel at room temperature. WIDECARS is also designed for measurements of all the major species (except water) in supersonic combustion flows fueled with hydrogen and hydrogen/ethylene mixtures (N2, O2, H2, C2H4, CO, and CO2). This instrument can characterize supersonic combustion fueled with surrogate fuel mixtures of hydrogen and ethylene. This information can lead to a better understanding of the chemistry and performance of supersonic combustion fueled with cracked jet propulsion (JP)-type fuel.

Tedder, Sarah Augusta Umberger↗
NASA NTRS1951

Exhaust turbine and jet propulsion systems

DVL experimental and analytical work on the cooling of turbine blades by using ram air as the working fluid over a sector or sectors of the turbine annulus area is summarized. The subsonic performance of ram-jet, turbo-jet, and turbine-propeller engines with both constant pressure and pulsating-flow combustion is investigated. Comparison is made with the performance of a reciprocating engine and the advantages of the gas turbine and jet-propulsion engines are analyzed. Nacelle installation methods and power-level control are discussed.

Leist, Karl↗
NASA NTRS1989

The gaseous jet in supersonic crossflow

An analytical/numerical model for the deflection and mixing of a single gaseous jet in a supersonic crossflow is presented. The jet cross-section is described in terms of the compressible vortex pair resulting from viscous and impulsive forces acting at the jet periphery, and the vortex pair data are combined with data for the mass and momentum balance along the jet axis in order to model the trajectory and mixing of the injected fluid. A numerical technique is employed to solve for the inviscid outer flow and the position of the bow shock which envelopes the jet. The model is shown to be capable of predicting overall jet penetration (for perfectly or slightly underexpanded jets) to within 10 percent of experimental findings, while requiring only a few seconds of computer time.

Heister, S. D.↗
NASA NTRSDate not supplied

Design and Analysis of A Jet Stretcher for High-Altitude Supersonic Free Jet Testing

A jet stretcher can be used to extend the region of clean flow for a test article in a supersonic free jet. The device acts to shield the article from shock waves reflected from the free jet shear layer. It can also allow for overexpanded nozzle operation through blocking shocks emanating from the nozzle lip, enlarging the potential test envelope. The FUN3D computational fluid dynamics solver was used to test a design process for developing jet stretchers. The inner surface of the axisymmetric jet stretcher was obtained from a streamline extracted from a free flight simulation around a notional test article at the intended test condition of Mach 3.2, 53,000 ft. The test article and jet stretcher were then simulated in a free jet nozzle exhaust, and the flowfield within a notional inlet aperture was compared between the installed and free flight calculations. Ambient pressure was increased until separation within the free jet nozzle finally induced disturbances at the inlet. The jet stretcher was shown to provide clean flow to the inlet at cell pressure ratios up to 2.8. A process for trimming the axisymmetric jet stretcher was also tested. This was intended to provide blockage relief for complex test articles, aiding with starting, as well as reducing weight and fabrication cost. The trimmed jet stretcher performed identically to the axisymmetric model at slightly-overexpanded conditions, but at cell pressure ratios above 1.3 allowed disturbances from the trailing edge to reach the inlet.

free jet↗