Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flexure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Loading Capabilities of Irradiated 3-D Printed Polymers

Gamma radiation is the emission of a high-energy photon from a radioactive source. The photon then interacts with an atom potentially damaging it. While time has shown that gamma radiation has a little effect on metals, the same cannot be said about plastic. The use of these types of materials in radioactive areas has increased for many reasons ranging from the weight difference between plastics and metals to the costs associated with doing so. For example, a potential use for radiation resistant plastics could be longer lasting, cost effective, and light weight radiation detection devices sent to probe an area that may present unsafe conditions for humans to survey. For these reasons and more, finding a plastic polymer that can withstand radiation for an extended period of time would make a great impact on the nuclear industry. In this experiment, two different polymers will undergo a series of strength tests before and after being exposed to radiation after different amounts of time up to two weeks. There are two sets of plastic polymers that will be used. Each set will consist of an nonirradiated, control subset, and subsets subject to radiation for one day, one week, and two weeks. The radiation source is 1100 Ci cobalt- 60. The specimens are placed on a foam platform such that they will be exposed as evenly as possible. They are then lowered into the radiation chamber where they are surround by cobalt-60 sources and irradiated for the given amount of time. The specimens will be tested for tensile strength and flexural strength according to ASTM standards. For tensile testing, the specimen has a 'dog bone' shape. The specimen is gripped at the wide ends, and pulled away from the center at a constant rate until failure. To test flexural strength, the specimens will be subject to a 3-point bend test. The specimen is held in place by three points, center top side and both ends bottom side. Load is applied at a constant rate on the center of the specimen until failure. The calculations to be considered for comparison after performing these tests include the tensile strength and stress, elongation, flexural stress and strain, and elasticity. Once these tests are completed, testing specimens that have been 3D printed with different print orientations will be considered and tested. The results from both experiments will help create strong, radiation resistant products in a expeditious manner that could really push the current limitations and expand the use of radiation resistant material.

36 MATERIALS SCIENCE↗

Evaluating the Lightning Strike Damage Tolerance for CFRP Composite Laminates Containing Conductive Nanofillers

Conductive nanofillers, such as carbon nanotube, graphene nanoplatelets, and carbon black particles (with diameters in nanometers) have been shown to enhance the electrical conductivity of fiber reinforced polymer matrix composites in many existing studies. The motivation is primarily for lightning strike protection, electromagnetic interference shielding, de-icing, and the manufacturing of lightweight electronic components. Here, we evaluate the lightning strike damage tolerance of carbon fiber reinforced polymer (CFRP) matrix composite laminates containing conductive nanofillers with varying weight fractions, including carbon black (CB), carbon nanotubes (CNT), and a mix of CB and CNT, through simulated lightning strike tests, followed by both non-destructive ultrasonic inspection and destructive sectioning to characterize the damage inflicted by the simulated lightning strike. Three-point flexural tests are performed to evaluate the residual strength retained by all CFRP specimens. Results show that lightning strike damage experienced varying levels of reduction for CFRP composite specimens containing conductive fillers in comparison to the baseline specimen without fillers. Notably, the delamination only penetrated to the interface between the 1st and 2nd layer for the specimen with 0.25 wt.% CNT in comparison to the baseline CFRP specimen for which the delamination penetrated to the interface between the 5th and 6th layer. Moreover, the retention of the flexural modulus increased from 26.5% to a maximum of 95.0% for the specimen with 0.25 wt.% hybrid CB and CNT. Yet, we show that using our chosen conductive fillers cannot fully eliminate lightning strike damage. Additionally, adding conductive fillers could compromise the flexural properties. We provide discussions on future recommendations on using conductive fillers for the lightning strike protection of CFRP composites.

36 MATERIALS SCIENCE↗

High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology

Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.

36 MATERIALS SCIENCE↗

Acoustic emission for characterising the crack propagation in strain-hardening cement-based composites (SHCC)

This paper presents the analysis of crack propagation in strain-hardening cement-based composite (SHCC) under tensile and flexural load by using acoustic emission (AE). AE is a non-destructive technique to monitor the development of structural damage due to external forces. The main objective of this research was to characterise the cracking behaviour in SHCC in direct tensile and flexural tests by using AE. A better understanding of the development of microcracks in SHCC will lead to a better understanding of pseudo strain-hardening behaviour of SHCC and its general performance. ARAMIS optical deformation analysis was also used in direct tensile tests to observe crack propagation in SHCC materials. For the direct tensile tests, SHCC specimens were prepared with polyvinyl alcohol (PVA) fibre with three different volume percentages (1%, 1.85% and 2.5%). For the flexural test beam specimens, only a fibre dosage of 1.85% was applied. It was found that the application of AE in SHCC can be a good option to analyse the crack growth in the specimens under increasing load, the location of the cracks and most importantly the identification of matrix cracking and fibre rupture or slippage.

36 MATERIALS SCIENCE↗

Application of materials informatics to vapor-grown carbon nanofiber/vinyl ester nanocomposites through self-organizing maps and clustering techniques

Data mining and knowledge discovery techniques were employed herein to acquire new information on the viscoelastic, flexural, compressive, and tensile properties of vapor-grown carbon nanofiber (VGCNF)/vinyl ester (VE) nanocomposites. Formulation and processing factors (curing environment, presence or absence of dispersing agent, mixing method, VGCNF weight fraction, VGCNF type, high-shear mixing time, and sonication time) and testing temperature were utilized as inputs and the true ultimate strength, true yield strength, engineering elastic modulus, engineering ultimate strength, flexural modulus, flexural strength, storage modulus, loss modulus, and tan delta were selected as outputs. The data mining and knowledge discovery algorithms used in this study include self-organizing maps (SOMs) and clustering techniques. SOMs demonstrated that temperature and tan delta had the most significant effects on the output responses followed by the VGCNF high-shear mixing time, and sonication time. SOMs were also used to produce optimal responses using certain combination(s) of inputs. Fuzzy C-means algorithm (FCM) was also applied to discover patterns in the nanocomposite behavior subsequent to a principal component analysis (PCA), which is a dimensionality reduction technique. Utilizing these techniques, the nanocomposite specimens were separated into different clusters based on the testing temperature (30 °C and 120 °C being the most dominant responses), tan delta, high-shear mixing time, and sonication time. Furthermore, the VGCNF/VE specimens were separated into a cluster based on their viscoelastic responses (storage and loss moduli) at the same temperature. The FCM results indicate that, while all nanocomposite properties in the new framework are essential, the viscoelastic responses of the VGCNF/VE specimens are the most significant. Here this work highlights the utility of data mining and knowledge discovery techniques in the context of materials informatics for the discovery of patterns and trends in the material behavior that are not immediately known.

36 MATERIALS SCIENCE↗

In situ observation of the deformation and fracture of an alumina-alumina ceramic-matrix composite at elevated temperature using x-ray computed tomography

The deformation and fracture of a 0/90° Nextel 720 mullite fibre / alumina matrix ceramic-matrix composite material has been observed by in situ synchrotron x-ray computed micro-tomography at ambient temperature and at 1100 °C. A three-point loading configuration was used and samples were loaded monotonically until final fracture. Here, the flexural strength was found to be unaffected by temperature. 3D visualisation of the microstructure showed fracture occurred by propagation of internal cracks at stresses close to the flexural strength. Shear fractures propagated across fibre bundles that were oriented perpendicular to the flexural stress at both room temperature and 1100 °C. At the higher temperature, an additional failure mode of delamination was observed, that may arise from relaxation of thermal residual stresses and creep.

36 MATERIALS SCIENCE↗

Development of U-Frame Bending System for Studying the Vibration Integrity of Spent Nuclear Fuel

A bending fatigue system developed to evaluate the response of spent nuclear fuel rods to vibration loads is presented. Design and analysis, fabrication, modification, calibration, and instrumentation are described. The system is composed of a U-frame testing setup for imposing bending loads on the spent fuel rod test specimen and a method for measuring the curvature of the rod during bending. The U-frame setup consists of two rigid arms, linking members, and linkages to a universal testing machine. The test specimen s curvature of bending is obtained through a three-point deflection measurement method consisting of three LVDTs mounted to the side connecting plates of the U-frame to capture the deformation of the test specimen. The system has some unique features: 1) The test specimen is installed by simple insertion using linear bearings incorporated with rigid sleeves. 2) Reverse cyclic bending tests can be carried out effectively and efficiently by push and pull at the loading point of the setup. Any test machine with a linear motion function can be used to drive the setup. 3) The embedded and preloaded linear roller bearings eliminate the backlash that exists in the conventional reverse bend tests. 4) The number of linkages between the U-frame and the universal machine is minimized. Namely, there are only two linkages needed at the two loading points of a U-frame setup, whereas a conventional four/three-point bend test frame requires four linkages. 5) The curvature measurement is immune to the effects arising from compliant layers and the rigid body motion of the machine. The compliant layers are used at the holding areas of the specimen to prevent contact damage. The tests using surrogate specimens composed of SS cladding/tube revealed several important phenomena that may cast light on the expected response of a spent fuel rod: 1) Cyclic quasi-static load (10 N/s under force control) in compressive mode (with respect to that at the loading point of the U-frame) produced increased irreversible or plastic curvature and also increased flexural rigidity of the surrogate rod. 2) Dynamic cyclic load (at least 1 Hz) in compressive mode resulted in increased flexural rigidity of the surrogate rod prior to SS cladding fracture. 3) Pellets and epoxy bonding exhibited various effects on the response of surrogate rods during the loading process as validated from static tests. 4) Dynamic cyclic load (2 Hz) in reverse mode demonstrated a substantial cyclic softening before the fracture of the surrogate rod. The degree of decrease in flexural rigidity was consistent in both measurement and on-line monitoring. The developed U-frame system is thus verified and demonstrated to be ready for further pursuit in hot-cell tests.

fuel transporation↗

Additive manufacturing of strong silica sand structures enabled by polyethyleneimine binder

Abstract Binder Jet Additive Manufacturing (BJAM) is a versatile AM technique that can form parts from a variety of powdered materials including metals, ceramics, and polymers. BJAM utilizes inkjet printing to selectively bind these powder particles together to form complex geometries. Adoption of BJAM has been limited due to its inability to form strong green parts using conventional binders. We report the discovery of a versatile polyethyleneimine (PEI) binder for silica sand that doubled the flexural strength of parts to 6.28 MPa compared with that of the conventional binder, making it stronger than unreinforced concrete (~4.5 MPa) in flexural loading. Furthermore, we demonstrate that PEI in the printed parts can be reacted with ethyl cyanoacrylate through a secondary infiltration, resulting in an increase in flexural strength to 52.7 MPa. The strong printed parts coupled with the ability for sacrificial washout presents potential to revolutionize AM in various applications including construction and tooling.

36 MATERIALS SCIENCE↗

Enhancing the Mechanical Toughness of Epoxy-Resin Composites Using Natural Silk Reinforcements

Strong and tough epoxy composites are developed using a less-studied fibre reinforcement, that of natural silk. Two common but structurally distinct silks from the domestic B. mori/Bm and the wild A. pernyi/Ap silkworms are selected in fabric forms. We show that the toughening effects on silk-epoxy composites or SFRPs are dependent on the silk species and the volume fraction of silk. Both silks enhance the room-temperature tensile and flexural mechanical properties of the composite, whereas the more resilient Ap silk shows a more pronounced toughening effect and a lower critical reinforcement volume for the brittle-ductile transition. Specifically, our 60 vol.% Ap-SFRP displays a three-fold elevation in tensile and flexural strength, as compared to pure epoxy resin, with an order of magnitude higher breaking energy via a distinct, ductile failure mode. Importantly, the 60 vol.% Ap-SFRP remains ductile with 7% flexural elongation at lower temperatures (-50 °C). Under impact, these SFRPs show significantly improved energy absorption, and the 60 vol.% Ap-SFRP has an impact strength some eight times that of pure epoxy resin. Lastly, the findings demonstrate both marked toughening and strengthening effects for epoxy composites from natural silk reinforcements, which presents opportunities for mechanically superior and "green" structural composites.

36 MATERIALS SCIENCE↗

Dynamic Characteristics of Multistory Buildings

In order to evaluate unit stresses or to estimate possible damage in multistory buildings from earthquake or ground motion from underground nuclear explosion it is essential to determine how much of the dynamic response at any level is due to various types of freedom. The effects of shear deformation between floors, joint rotation, over-all flexure, and ground compliance are considered. Joint rotation and over-all flexure are evaluated over a wide range of building characteristics with simply determined indices. Further, a period synthesis concept and a pseudo-stiffness procedure are proposed to enable the determination of periods, mode shapes and stiffnesses with consideration of joint rotation, over-all flexure and ground compliance while performing simple labor-saving analyses for assumed rigid-floor shear buildings. The first three modes of vibration are considered in elastic free vibration. The buildings and models are symmetric in plan without torsional coupling.

42 ENGINEERING↗

Effects of gold patterning on the bending profile and frequency response of a microcantilever

We have systematically investigated the effect of various gold patterns on the bending profile and frequency response of a microcantilever. The gold patterns were deposited on the cantilever arrays using four types of shadow mask. The local bending profile, slope, and curvature varied depending on the area and position of the gold pattern. Also, the variations in the first three modes of the flexural resonance frequencies of the gold patterned cantilevers were measured to understand the opposing effects of mass loading and flexural rigidity; both of these parameters are dependent on the position and area of the gold pattern. The experimental results validated the theoretical one-dimensional model introduced by Tamayo et al. Appl. Phys. Lett. 89, 224104 2006 and our calculations using the finite element method. The gold patterns giving the maximum response of the mass loading and flexural rigidity change were determined by examining how the relative resonance frequency shifts as a function of the distance of the gold coating from the free end or clamping region. The results of this study can potentially be applied in the design of a microcantilever sensor in which pattern analysis is utilized to determine the presence of adsorbed biological and chemical molecules.

42 ENGINEERING↗

Frontside-micromachined planar piezoresistive vibration sensor: Evaluating performance in the low frequency test range

Using a surface piezoresistor diffusion method and front-side only micromachining process, a planar piezoresistive vibration sensor was successfully developed with a simple structure, lower processing cost and fewer packaging difficulties. The vibration sensor had a large sector proof mass attached to a narrow flexure. Optimization of the boron diffusion piezoresistor placed on the edge of the narrow flexure greatly improved the sensitivity. Planar vibration sensors were fabricated and measured in order to analyze the effects of the sensor dimensions on performance, including the values of flexure width and the included angle of the sector. Sensitivities of fabricated planar sensors of 0.09–0.46 mV/V/g were measured up to a test frequency of 60 Hz. The sensor functioned at low voltages (<3 V) and currents (<1 mA) with a high sensitivity and low drift. At low background noise levels, the sensor had performance comparable to a commercial device.

36 MATERIALS SCIENCE↗

A serial-kinematic nanopositioner for high-speed atomic force microscopy

A flexure-guided serial-kinematic XYZ nanopositioner for high-speed Atomic Force Microscopy is presented in this paper. Two aspects influencing the performance of serial-kinematic nanopositioners are studied in this work. First, mass reduction by using tapered flexures is proposed to increased the natural frequency of the nanopositioner. 25% increase in the natural frequency is achieved due to reduced mass with tapered flexures. Second, a study of possible sensor positioning in a serial-kinematic nanopositioner is presented. An arrangement of sensors for exact estimation of cross-coupling is incorporated in the proposed design. A feedforward control strategy based on phaser approach is presented to mitigate the dynamics and nonlinearity in the system. Limitations in design approach and control strategy are discussed in the Conclusion.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Enhancement of magnetic domain wall velocity via resonant dissipation of standing wave modes of domain wall structure with perpendicular magnetic anisotropy

The dynamic behaviors of magnetic domain walls have significant implications for developing advanced spintronic devices. In this study, we investigate the intriguing resonance phenomenon within the magnetic domain wall structure, focusing on the dissipation mechanism and its impact on domain wall dynamic motion. By applying a static external magnetic field, we observe a remarkable amplification of domain wall velocity through the resonant excitations of the flexure modes. The resonance of the flexure mode exerts an indirect influence on the domain wall velocity through energy dissipation, leading to a significant enhancement from the predictions of the one-dimensional Walker model. We establish a robust model platform rooted in energy dissipation allows comprehensive understanding the dramatic enhancement of domain wall velocity observed during width-directional flexure mode resonance. By directly quantifying energy dissipation, our approach provides highly effective and accurate estimates of domain wall velocity, surpassing previous methods that focus solely on the instantaneous dynamics of the domain wall structure. These findings offer crucial insights into the fundamental mechanisms governing the dynamics of domain walls and other magnetic systems, such as magnetic skyrmions, bubbles, and magnetic vortices, paving the way for development and optimization of next-generation spintronic devices.

Collective dynamics↗

A High-Speed Large-Range Tip-Tilt-Piston Micromirror Array

This work introduces the design of a high fill-factor (>99%) micromirror array (MMA) that consists of 1mm2 hexagonal mirrors, which are expected to each independently achieve continuous, closed-loop control of three degrees of freedom (DOFs)—tip, tilt, and piston—over large ranges (>±10o rotation and >±30μm translation) at high speeds (~45kHz for a 1o amplitude of rotational oscillation). The flexure topology of this array is designed using the Freedom, Actuation, and Constraint Topologies (FACT) synthesis approach, which utilizes geometric shapes to help designers rapidly consider every flexure topology that best achieves a desired set of DOFs driven by decoupled actuators. The geometry of this array’s comb-drive actuators are optimized in conjunction with the geometry of the system’s flexures using a novel approach. The analytical models underlying this approach are verified using finite element analysis (FEA) and validated using experimental data. The capabilities of this new mirror array will enable, or significantly improve, the performance of a variety of high-impact optical technologies such as advanced optical switches, spatial-light modulators, displays, and laser steering or scanning devices.

42 ENGINEERING↗

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

ABSTRACT Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp, and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m 1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m 1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m 1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO 2 , the crack deflection and bridging of SiCp and SiCw, and the pull‐out of SiCw.

Liu, Longyang↗

Thermal shock resistance of additively manufactured alumina

The mechanical behavior and cracking patterns of thermally-shocked additively manufactured alumina were investigated. The flexural strength of test specimens that had been heated to temperatures ranging from 200°C to 1000°C and then rapidly quenched in water was determined at ambient temperature by four-point bending. Results indicated that the surface cracking patterns had a multifractal structure and that an increase in the thermal shock temperature led to an increase in the density and uniformity of the crack network. Further, the flexural strength results were analyzed with Weibull statistics, where the Weibull moduli for most of the thermal shock conditions tested were found to be statistically indistinguishable. It was also found that a significant decrease (~50%) in flexural strength occurred for heating temperatures ≥300°C. The effect of the manufacturing method on cracking patterns is discussed, as well as the implication of the material behavior for practical applications of these materials.

36 MATERIALS SCIENCE↗