Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “femtosecond”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Wake Velocimetry of a Sphere-Cone Model in a Mach 10 Air Freestream using FLEET

Velocity measurements in the wake behind a sphere-cone-shaped vehicle wind tunnel model in a Mach 10 hypersonic air flow using femtosecond laser electronic excitation tagging (FLEET) are reported in this work. The FLEET measurements were performed at 1 kHz using a femtosecond laser centered at 800 nm and an ultrahigh-speed intensified camera system. The results reported here are for a single freestream condition corresponding to approximately Re ∞ /L = 3.6∙10 6 m -1 . The performance of the velocimetry instrument was evaluated in the quiescent test section at conditions relevant to the wake measurements. For velocity measurements in the wake, the FLEET measurement volume was translated to several radial locations from the model centerline in the vertical direction and at a streamwise location corresponding to approximately 12 mm from the payload. Reverse flow with mean velocities ranging from -12 m/s to -48 m/s were observed in the recirculating region of the wake, whereas hypersonic velocities in the range of 1079 m/s to 1183 m/s were observed in the free shear layer. A velocity uncertainty methodology is also outlined and applied for the reported measurements. The velocity data reported in this work is expected to play a significant role in the validation of computational codes modeling the hard-to-predict separated hypersonic wake.

FLEET↗
NASA NTRSDate not supplied

Wake Velocimetry of a Sphere-Cone Model in a Mach 10 Air Freestream using FLEET

Velocity measurements in the wake behind a sphere-cone-shaped vehicle wind tunnel model in a Mach 10 hypersonic air flow using femtosecond laser electronic excitation tagging (FLEET) are reported in this work. The FLEET measurements were performed at 1 kHz using a femtosecond laser centered at 800 nm and an ultrahigh-speed intensified camera system. The results reported here are for a single freestream condition corresponding to approximately Re ∞ /L = 3.6∙10 6 m -1 . The performance of the velocimetry instrument was evaluated in the quiescent test section at conditions relevant to the wake measurements. For velocity measurements in the wake, the FLEET measurement volume was translated to several radial locations from the model centerline in the vertical direction and at a streamwise location corresponding to approximately 12 mm from the payload. Reverse flow with mean velocities ranging from -12 m/s to -48 m/s were observed in the recirculating region of the wake, whereas hypersonic velocities in the range of 1079 m/s to 1183 m/s were observed in the free shear layer. A velocity uncertainty methodology is also outlined and applied for the reported measurements. The velocity data reported in this work is expected to play a significant role in the validation of computational codes modeling the hard-to-predict separated hypersonic wake.

FLEET↗
DOE OSTI2024

A Methodology for determining optimal milling parameters for low-taper microtensile sample production

Femtosecond lasers are beginning to see an increase in interest for industrial and high throughput microsample milling applications. Despite this, much of the literature regarding removal rate studies for ultrashort pulse laser milling continues to focus on single-pulse or similar experiments that have a very small time on target. The material volume removal rates of femtosecond milling can vary wildly depending on parameters like laser scan speed, hatch spacing, z-axis step size, and pulses on the material. Currently, there is no established methodology for determining the optimal values of these parameters for micromilling applications. This methodology was developed in this study. The methodology consists of a pulse study, a repeat study, and a z-step study that will return the milling parameters that resulted in the largest volume removal rate for the laser used for this research. The methodology was created for the laser system used in this study, and was tested on 316 Stainless Steel, but was developed in such a way that it may be adapted to any material, and with some tweaking of variables might be used in other laser systems. The laser system used in this study utilizes a novel positioning stage that introduces 6 degrees of freedom to the translation of laser samples, being able to tilt and move in all three axes. Using both the developed methodology and the unique capabilities of the laser microtensile samples were produced with taper angles of <1° in 316 Stainless Steel.

Barker, Zachary Wayne↗
DOE OSTI2022

Methods and apparatus for comprehensive characterization of performance attributes and damage thresholds of ultrafast laser optics

It is presently well understood that the operational performance limits of optics are determined by three fundamental attributes: the initiation of laser-induced damage, the growth of damage sites, and the transient (nondamaging) modification of optical parameters. The comprehensive characterization of the performance limitations of ultrafast optics requires consideration of all three fundamental attributes. Here, the vast majority of literature to date, however, has focused primarily on damage-initiation and testing systems that are largely focused on determining the damage-initiation threshold under single- and multipulse excitation. In this work, we discuss a testing apparatus that was designed to offer the capability to adequately characterize all three of these performance attributes under femtosecond, near-infrared laser irradiation. Key aspects of methodology are discussed, including high-dynamic-range energy control, variable beam size, wavelength tunability, B-integral management, and functional performance characterization to explore the true operational limits of the components. Example results for a metal-dielectric mirror demonstrate the test station’s operation.

42 ENGINEERING↗
DOE OSTI2022

Large-Area Lasing in Nanoscale Complex Media: The Critical Role of Local Dielectric Environment

Controlling how electromagnetic waves interact with complex media is critical for applications in imaging and focusing. Such lightwave interactions with complex media can lead to dramatic optical effects like lasing. While much work in random lasing focus on understanding how gain and scattering co-operatively generate lasing, little work has focused on how to manipulate the lasing threshold without modifying the structural disorder. Here, a simple, mostly unexplored, strategy is demonstrated that employs atomic layer deposition (ALD) to tune the local near-field environment while preserving the underpinning disorder—controlling lasing in a nanoscale complex medium on a large scale (>cm 2 ). The nanoscale complex medium is a quasi-2D system of coupled zinc oxide nanospheres with overall thickness deep in the sub-wavelength regime (≈λ/4). Near-ultraviolet femtosecond spectroscopy probes the broadband response of the gain nanomaterial, details how ALD process fundamentally modifies the fast-picosecond and slow-nanosecond carrier dynamics, and informs on the relevant timescales critical for lasing. Full-field electromagnetic simulations provide critical insights about how near-field dielectric environment modifies the nanostructure's scattering cross-section, which ultimately results in enhanced lasing. Importantly, these results highlight a simple path to control how electromagnetic waves interact in a complex medium, a key step toward large-scale implementation of complex lasers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rational Control of Off‐State Heterogeneity in a Photoswitchable Fluorescent Protein Provides Switching Contrast Enhancement**

Abstract Reversibly photoswitchable fluorescent proteins are essential markers for advanced biological imaging, and optimization of their photophysical properties underlies improved performance and novel applications. Here we establish a link between photoswitching contrast, one of the key parameters that dictate the achievable resolution in nanoscopy applications, and chromophore conformation in the non‐fluorescent state of rsEGFP2, a widely employed label in REversible Saturable OpticaL Fluorescence Transitions (RESOLFT) microscopy. Upon illumination, the cis chromophore of rsEGFP2 isomerizes to two distinct off ‐state conformations, trans1 and trans2 , located on either side of the V151 side chain. Reducing or enlarging the side chain at this position (V151A and V151L variants) leads to single off ‐state conformations that exhibit higher and lower switching contrast, respectively, compared to the rsEGFP2 parent. The combination of structural information obtained by serial femtosecond crystallography with high‐level quantum chemical calculations and with spectroscopic and photophysical data determined in vitro suggests that the changes in switching contrast arise from blue‐ and red‐shifts of the absorption bands associated to trans1 and trans2 , respectively. Thus, due to elimination of trans2 , the V151A variants of rsEGFP2 and its superfolding variant rsFolder2 display a more than two‐fold higher switching contrast than their respective parent proteins, both in vitro and in E. coli cells. The application of the rsFolder2‐V151A variant is demonstrated in RESOLFT nanoscopy. Our study rationalizes the connection between structural and photophysical chromophore properties and suggests a means to rationally improve fluorescent proteins for nanoscopy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Terahertz inverse spin Hall effect in spintronic nanostructures with various ferromagnetic materials

Bilayers of ferromagnetic and heavy metal nanolayers excited with femtosecond laser pulses emit subpicosecond bursts of electromagnetic radiation with spectral frequencies up to several THz. We fabricated such spintronic THz emitters containing various ferromagnetic materials with vastly different magnetic remanence, saturation magnetization, and coercive fields. In all cases, the THz amplitude versus magnetic-field dependence follows the independently measured magnetization hysteresis loops and the THz polarization direction is perpendicular to the sample’s magnetization M, both consistent with the inverse spin Hall effect (ISHE) as the physical origin. The mV-level signals of observed THz transient also favor the ISHE over the anomalous Nernst effect (ANE). The M(T) variation governs the temperature dependence of the THz generation. Emitters with weakly remanent ferromagnets are magnetic-field tunable, while moderately and strongly remanent ferromagnets, once magnetized, allow intense THz generation even without an external field, nevertheless exhibiting low susceptibility to magnetic perturbations if the hysteresis loop is square. Hence, exploiting the magnetic properties of the ferromagnetic layer enables tailoring of weakly temperature-dependent spintronic THz emitters. Finally, we explored the applicability of perovskite oxide materials such as La-Sr-Mn-O (LSMO) for THz transient generation. We detected weak (<40-μV amplitude) THz emissions from both LSMO/Au and pure LSMO nanostructures with no sign flip upon the sample reversal. Furthermore, we excluded the ISHE and believe it was likely governed by the ANE in the thick-film regime, although we cannot exclude the transient demagnetization mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High performance aluminum-air flow batteries through double-face architecture and laser-modified and friction-stir processed 3D anode

Aluminum-air batteries (AAB) are regarded as one of the most promising beyond-lithium high-energy-density storage candidates. Here, this paper introduces a three-dimensional (3D) Al 7075 anode enabled by femtosecond laser and friction-stir process which, along with a special double-face anode architecture provides world-class performance. Electrochemical characterizations prove that the corrosion resistance of the modified 3D Al 7075 FSP anode was enhanced, and electrochemically active surface area (ECSA) was increased compared with that of normal Al 7075 anode. Friction-stir processing reduced the mean grain size from 30 μm to 3 μm. The discharge performance of 3D Al 7075 FSP anode is shown to be quite stable, and the average values of energy density are significantly increased from 2256 mWh g –1 to 2941 mWh g –1 at 100 mA cm –2 . In a double-face flowing Al-air battery system, the 3D Al 7075 FSP anode exhibited significantly better electrocatalytic performance (discharge voltage of 0.76 V at 400 mA cm –2 , and power density of 337.8 mW cm –2 ) than that of a commercial Al 7075 anode.

25 ENERGY STORAGE↗
DOE OSTI2023

Plasmon-Induced Hot-Carrier Excited-State Dynamics in Plasmonic Semiconductor Nanocrystals

The variance of carrier relaxation pathways for WO 3–x plasmonic semiconductor nanocrystals (PSNCs) is monitored by transient absorption spectroscopy following excitation of the localized surface plasmon resonance (LSPR) versus the optical band gap (E g,opt ). Excitation of the LSPR leads to efficient hot carrier population above the Fermi level in WO 3–x via Landau damping, in analogy to noble metal LSPR relaxation mechanisms. Hot carrier depopulation occurs on the femtosecond timescale, observed as the concomitant recovery of an LSPR bleach with the appearance of discrete interband and intraband photoinduced absorption features. Further, by comparison, the direct excitation of E g,opt results in trion recombination at donor–acceptor sites within the WO 3–x NC, consistent with exciton decay dynamics observed for typical wide-band-gap semiconductor NCs. From the analysis of pump power dependency data, a hot-carrier electron–phonon coupling constant of 1.47 × 10 11 J K –1 s –1 cm –3 is extracted. The direct comparison of the decay dynamics following E g,opt versus LSPR excitation confirms that the observed plasmon in trioctylphosphine oxide passivated, spherical WO 3–x is a resonance state in which hot carriers are generated only from excitation on resonance with the LSPR frequency. This study on WO 3–x PSNCs provides a toolset that can be used to evaluate the role of hot carriers following LSPR excitation of n-type, plasmonic transparent conducting oxide NCs, where enhancement of photocatalysis, photovoltaic performance, and optical enhancement has been reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Excited-State-Selective Ultrafast Relaxation Dynamics and Photoisomerization of trans-4,4'-Azopyridine

Here, excited-state dynamics of trans-4,4’-azopyridine in ethanol is studied using femtosecond transient absorption with 30 fs temporal resolution. Exciting the system at three different wavelengths, 460- and 290-(275) nm, to access the S 1 n,π* and S 2 π,π* electronic states, respectively, reveals a 195 cm -1 vibrational coherence, that suggests that the same mode is active in both n,π* and π,π* relaxation channels. Following S 1 -excitation, relaxation proceeds via a nonrotational pathway, where a fraction of the n,π* population is trapped in a planar minimum (lifetime, 2.1 ps), while the remaining population travels further to a second shallow minimum (lifetime, 300 fs) prior to decay into the ground state. Population of the S 2 state leads to 30-fs non-rotational relaxation with a concurrent buildup of n,π* population and nearly simultaneous formation of hot ground state species. An increase in the cis-isomer quantum yield upon π,π* vs. n,π* excitation is observed, which is opposite to trans-azobenzene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Observation of a Picosecond Light-Induced Spin Transition in Polymeric Nanorods

Spin transition (ST) materials are attractive for developing photoswitchable devices, but their slow material transformations limit device applications. Size reduction could enable faster switching, but the photoinduced dynamics at the nanoscale remains poorly understood. Here, we report a femtosecond optical pump multimodal X-ray probe study of polymeric nanorods. Simultaneously tracking the ST order parameter with X-ray emission spectroscopy and structure with X-ray diffraction, we observe photodoping of the low-spin–lattice within ~150 fs. Above a ~16% photodoping threshold, the transition to the high-spin phase occurs following an incubation period assigned to vibrational energy redistribution within the nanorods activating the molecular spin switching. Above ~60% photodoping, the incubation period disappears, and the transition completes within ~50 ps, preceded by the elastic nanorod expansion in response to the photodoping. These results support the feasibility of ST material-based GHz optical switching applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strong-Field Control of Plasmonic Properties in Core–Shell Nanoparticles

Utilization of the plasmonic response in nanosystems is a key component of nanophotonics that is typically altered by varying the incident optical frequency or the material configuration. However, in this work we demonstrate that employing intense, femtosecond laser fields unlock nonlinear light–matter interactions such that precise control of the optical response is achieved solely by adjusting the incident intensity. The plasmonic properties of Au/SiO 2 nanoshells are manipulated by exploiting the nonlinear index of refraction of gold and experimentally observed by employing photoelectrons emitted during the interaction as a sensitive, sub-wavelength probe. A striking transition seen in the photoelectron energy spectrum between the weak and strong-field regime is verified by a modified Mie theory simulation that incorporates the nonlinear dielectric nanoshell response. The exhibited intensity-dependent optical control of the plasmonic response in prototypical core–shell nanoparticles paves the way toward ultrafast switching and opto-electronic signal modulation with more complex nanostructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

In Situ Structural Observation of a Substrate- and Peroxide-Bound High-Spin Ferric-Hydroperoxo Intermediate in the P450 Enzyme CYP121

The P450 enzyme CYP121 from Mycobacterium tuberculosis catalyzes a carbon–carbon (C–C) bond coupling cyclization of the dityrosine substrate containing a diketopiperazine ring, cyclo(l-tyrosine-l-tyrosine) (cYY). An unusual high-spin (S = 5/2) ferric intermediate maximizes its population in less than 5 ms in the rapid freeze-quenching study of CYP121 during the shunt reaction with peracetic acid or hydrogen peroxide in acetic acid solution. Here, we show that this intermediate can also be observed in the crystalline state by EPR spectroscopy. By developing an on-demand-rapid-mixing method for time-resolved serial femtosecond crystallography with X-ray free-electron laser (tr-SFX-XFEL) technology covering the millisecond time domain and without freezing, we structurally monitored the reaction in situ at room temperature. After a 200 ms peracetic acid reaction with the cocrystallized enzyme–substrate microcrystal slurry, a ferric-hydroperoxo intermediate is observed, and its structure is determined at 1.85 Å resolution. The structure shows a hydroperoxyl ligand between the heme and the native substrate, cYY. The oxygen atoms of the hydroperoxo are 2.5 and 3.2 Å from the iron ion. The end-on binding ligand adopts a near-side-on geometry and is weakly associated with the iron ion, causing the unusual high-spin state. This compound 0 intermediate, spectroscopically and structurally observed during the catalytic shunt pathway, reveals a unique binding mode that deviates from the end-on compound 0 intermediates in other heme enzymes. The hydroperoxyl ligand is only 2.9 Å from the bound cYY, suggesting an active oxidant role of the intermediate for direct substrate oxidation in the nonhydroxylation C–C bond coupling chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhanced Dynamics and Charge Transport at the Eutectic Point: A New Paradigm for the Use of Deep Eutectic Solvent Systems

Deep eutectic solvents (DESs) are a class of versatile solvents with promise for a wide range of applications, from separation processes to electrochemical energy storage technologies. A fundamental understanding of the correlation among the structure, thermodynamics, and dynamics of these materials necessary for targeted rational design for specific applications is still nascent. Here, we employ differential scanning calorimetry (DSC), broadband dielectric spectroscopy (BDS), and femtosecond transient absorption spectroscopy (fs-TAS) to investigate the correlation among thermodynamics, dynamics, and charge transport in mixtures comprising a wide range of compositions of choline chloride (ChCl) and ethylene glycol (EG). Detailed analyses reveal that (i) the eutectic composition of this prototypical DES occurs in the 15–20 mol % ChCl in the EG range rather than the previously assumed 33 mol %, and (ii) both rotational dynamics and charge transport at the eutectic composition are enhanced in this composition range. These findings highlight the fundamental interplay between thermodynamics and dynamics in determining the properties of DESs that are relevant to many applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Cooperative allostery and structural dynamics of streptavidin at cryogenic- and ambient-temperature

Multimeric protein assemblies are abundant in nature. Streptavidin is an attractive protein that provides a paradigm system to investigate the intra- and intermolecular interactions of multimeric protein complexes. Also, it offers a versatile tool for biotechnological applications. Here, we present two apo-streptavidin structures, the first one is an ambient temperature Serial Femtosecond X-ray crystal (Apo-SFX) structure at 1.7 Å resolution and the second one is a cryogenic crystal structure (Apo-Cryo) at 1.1 Å resolution. These structures are mostly in agreement with previous structural data. Combined with computational analysis, these structures provide invaluable information about structural dynamics of apo streptavidin. Collectively, these data further reveal a novel cooperative allostery of streptavidin which binds to substrate via water molecules that provide a polar interaction network and mimics the substrate biotin which displays one of the strongest affinities found in nature.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Photo-induced structural dynamics of o -nitrophenol by ultrafast electron diffraction

The photo-induced dynamics of o-nitrophenol, particularly its photolysis, has garnered significant scientific interest as a potential source of nitrous acid in the atmosphere. Although the photolysis products and preceding photo-induced electronic structure dynamics have been investigated extensively, the nuclear dynamics accompanying the non-radiative relaxation of o-nitrophenol on the ultrafast timescale, which include an intramolecular proton transfer step, have not been experimentally resolved. Herein, we present a direct observation of the ultrafast nuclear motions mediating photo-relaxation using ultrafast electron diffraction. Here, this work spatiotemporally resolves the loss of planarity which enables access to a conical intersection between the first excited state and the ground state after the proton transfer step, on the femtosecond timescale and with sub-Angstrom resolution. Our observations, supported by ab initio multiple spawning simulations, provide new insights into the proton transfer mediated relaxation mechanism in o-nitrophenol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Direct imaging of plasma waves using ultrafast electron microscopy

A femtosecond plasma imaging modality based on a new development of ultrafast electron microscope is introduced. We investigated the laser-induced formation of high-temperature electron microplasmas and their subsequent non-equilibrium evolution. Based on a straightforward field imaging principle, we directly retrieve detailed information about the plasma dynamics, including plasma wave structures, particle densities, and temperatures. We discover that directly subjected to a strong magnetic field, the photo-generated microplasmas manifest in novel transient cyclotron echoes and form new wave states across a broad range of field strengths and different laser fluences. Intriguingly, the transient cyclotron waves morph into a higher frequency upper-hybrid wave mode with the dephasing of local cyclotron dynamics. The quantitative real-space characterizations of the non-equilibrium plasma systems demonstrate the feasibilities of a new microscope system in studying the plasma dynamics or transient electric fields with high spatiotemporal resolutions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗