Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “failure mode analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Spectrum analysis of acoustic emissions from boron-aluminum composites

Acoustic emissions were monitored from unidirectional tension specimens of boron-aluminum composites. It is shown that a sudden increase in count rate presages final failure. This sudden increase, however, occurs at a variable point relative to final failure load. Spectrum analysis in the range from 1 to 100 kHz was performed on the emissions with the result that no immediately obvious recognition pattern exists to distinguish between types of failure mechanisms. It is suggested that either acoustic emissions cannot be used to distinguish different failure modes in boron-aluminum composites in the frequency range studied or the specimens used had only one failure mode operating with sufficient energy release to be detected. The spectrum analysis did show, however, that the acoustic emissions had frequency components much higher than the frequencies for the fundamental modes of natural vibration of the specimen.

Henneke, E. G., II↗
NASA NTRS1989

Scaling effects in the static large deflection response of graphite-epoxy composite beams

Scaling effects in the large deflection response of graphite-epoxy composite beams was investigated. Eight different scale model beams ranging from 1/6 to full-scale were subjected to an eccentric axial compressive load to promote large bending deformations and failures. Beams having laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic were tested to examine a wide variety of composite response and failure modes. The model beams were loaded under scaled test conditions until catastrophic failure. Data acquired included load, end displacement, and strain measurements, and qualitative failure measurements. The experimental data is compared to a large rotation beam analysis and a finite element model analysis. Results from the tests indicate that the beam response becomes nonlinear. Failure modes are consistent between scale models within a laminate family, however, a significant scale effect is observed in strength of the scaled beams.

Jackson, Karen E.↗
NASA NTRSDate not supplied

Understanding Variability in Mechanical Behavior of Adhesively Bonded Sandwich Joints due to Stochastic Material Damage

A mesoscale progressive damage analysis was applied to the analysis of recently tested adhesively bonded sandwich panels, in which ten nominally identical tension loaded panels failed in three different failure modes, with peakloads ranging from 13.0 –16.1 kips. A parametric finite element model for progressive damage analysis of an adhesively bonded joint (ABJ) considering matrix and fiber damage, and delamination cracks in unidirectional and fabric composite sections of the joint, as well as core crushing, and adhesive fracture was developed. The model was developed using Abaqus/Explicit and utilized continuum damage mechanics material models for intralaminar damage in the facesheet and doubler plies, cohesive elements for delamination and adhesive debonding, and discretized cells considering plasticity to model crushing of the aluminum honeycomb core. Analysis predictions obtained with a pristine model agreed well with the average experimental peak load, strain in the joint, and post-test damage states. Then, various methods to incorporate stochastic material variability into ABJ model were evaluated. These methods included simulation of pre-existing matrix damage, pre-existing adhesive porosity, and uniform modification of adhesive properties. These material and manufacturing defects changed the damage mode predictions in some cases. The analysis of stochastic strength due to the considered defects revealed unintuitive damage mode interaction in the ABJ, explaining some structure-property relationships observed experimentally.

Richard Larson↗
NASA NTRS1995

Probabilistic Fatigue And Flaw-Propagation Analysis

Probabilistic Failure Assessment for Fatigue and Flaw Propagation (PFAFAT II) package of software utilizing probabilistic failure-assessment (PFA) methodology to model flaw-propagation and low-cycle-fatigue modes of failure of structural components. Comprises one program for performing probabilistic crack-growth analysis and two programs for performing probabilistic low-cycle-fatigue analysis. These programs perform probabilistic fatigue and crack-propagation analysis by means of Monte Carlo simulation. PFAFAT II is extension of, rather than replacement for, PFAFAT software (NPO-18965). Written in FORTRAN 77.

Moore, Nicholas↗
NASA NTRS1973

The effects of out-of-phase biaxial-strain cycling on low-cycle fatigue.

The effects of out-of-phase or nonsychronous straining on low-cycle fatigue was investigated. Biaxial strains were imposed on thin-walled tubular 7075-T6 aluminum specimens by tension-compression and torsion. Phase angles of 0, 30, 45, 60, and 90 deg were applied between two strains. It was found that out-of-phase cycling has an effect on the failure mode in the low-cycle-fatigue range. An analysis based on the maximum total strain in three-dimensional strain is proposed for treating 'out-of-phase' straining conditions in low-cycle fatigue.

Zamrik, S. Y.↗
NASA NTRS1979

Design, durability and low cost processing technology for composite fan exit guide vanes

A lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application was investigated. Eight candidate material/design combinations were evaluated by NASTRAN finite element analyses. A total of four combinations were selected for further analytical evaluation, part fabrication by two ventors, and fatigue test in dry and wet condition. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation, and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Pre-test and post-test microstructural examination and nondestructive analyses were conducted to determine the effect of material variations on fatigue durability and failure mode. Relevant data were acquired with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits, and part price of the composite fan exit guide vane.

Blecherman, S. S.↗
NASA NTRS1980

Identification and analysis of factors affecting thermal shock resistance of ceramic materials in solar receivers

An analysis was conducted of the possible modes of thermal stress failure of brittle ceramics for potential use in point-focussing solar receivers. The pertinent materials properties which control thermal stress resistance were identified for conditions of steady-state and transient heat flow, convective and radiative heat transfer, thermal buckling and thermal fatigue as well as catastrophic crack propagation. Selection rules for materials with optimum thermal stress resistance for a particular thermal environment were identified. Recommendations for materials for particular components were made. The general requirements for a thermal shock testing program quantitatively meaningful for point-focussing solar receivers were outlined. Recommendations for follow-on theoretical analyses were made.

Hasselman, D. P. H.↗
NASA NTRS1981

An investigation of adhesive/adherend and fiber matrix interactions

Research during the report period focused on continued scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) of lap shear samples and flatwise tensile specimens and on the surface characterization of TiO2, Ti 6-4, and Ti powders with particular emphasis on their interaction with primer solutions of both polyphenylquinoxaline and LaRC-13 polyimide. The use of SEM and XPS in the analysis of Ti 6-4 adherend surfaces is described as well as differences in Ti 6-4 surface composition after different chemical pretreatments. Analysis of fractured surfaces is used to established the failure mode. The surface acidity of Ti 6-4 coupons can be established by reflectance visible spectroscopy using indicator dyes.

Beck, B.↗
NASA NTRS1991

Mission safety evaluation report for STS-35: Postflight edition

Space Transportation System 35 (STS-35) safety risk factors that represent a change from previous flights that had an impact on this flight, and factors that were unique to this flight are discussed. While some changes to the safety risk baseline since the previous flight are included to highlight their significance in risk level change, the primary purpose is to insure that changes which were too late too include in formal changes through the Failure Modes and Effects Analysis/Critical Items List (FMEA/CIL) and Hazard Analysis process are documented along with the safety position, which includes the acceptance rationale.

Hill, William C.↗
NASA NTRS2011

Response of Honeycomb Core Sandwich Panel with Minimum Gage GFRP Face-Sheets to Compression Loading After Impact

A compression after impact study has been conducted to determine the residual strength of three sandwich panel constructions with two types of thin glass fiber reinforced polymer face-sheets and two hexagonal honeycomb Nomex core densities. Impact testing is conducted to first determine the characteristics of damage resulting from various impact energy levels. Two modes of failure are found during compression after impact tests with the density of the core precipitating the failure mode present for a given specimen. A finite element analysis is presented for prediction of the residual compressive strength of the impacted specimens. The analysis includes progressive damage modeling in the face-sheets. Preliminary analysis results were similar to the experimental results; however, a higher fidelity core material model is expected to improve the correlation.

McQuigg, Thomas D.↗
NASA NTRS2014

A Failure Propagation Modeling Method for Launch Vehicle Safety Assessment

A method has been developed with the objective of making the potentially intractable problem of launch vehicle failure propagation somewhat less intractable. The approach taken is to essentially decouple the potentially multi-stepped propagation process into a series of bi-component transition probabilities. These probabilities are then used within a simple Monte Carlo simulation process through which the more complex behavior evolves. The process is described using a simple model problem and some discussion of enhancements for real-world applications is included. The role of the model within a broader analysis process for assessing abort effectiveness from launch vehicle failure modes is also described.

Lawrence, Scott↗
NASA NTRS1989

Development of a finite element based delamination analysis for laminates subject to extension, bending, and torsion

Delamination is a common failure mode of laminated composite materials. This type of failure frequently occurs at the free edges of laminates where singular interlaminar stresses are developed due to the difference in Poisson's ratios between adjacent plies. Typically the delaminations develop between 90 degree plies and adjacent angle plies. Edge delamination has been studied by several investigators using a variety of techniques. Recently, Chan and Ochoa applied the quasi-three-dimensional finite element model to the analysis of a laminate subject to bending, extension, and torsion. This problem is of particular significance relative to the structural integrity of composite helicopter rotors. The task undertaken was to incorporate Chan and Ochoa's formulation into a Raju Q3DG program. The resulting program is capable of modeling extension, bending, and torsional mechanical loadings as well as thermal and hygroscopic loadings. The addition of the torsional and bending loading capability will provide the capability to perform a delamination analysis of a general unsymmetric laminate containing four cracks, each of a different length. The solutions obtained using this program are evaluated by comparing them with solutions from a full three-dimensional finite element solution. This comparison facilitates the assessment of three dimensional affects such as the warping constraint imposed by the load frame grips. It wlso facilitates the evaluation of the external load representation employed in the Q3D formulation. Finally, strain energy release rates computed from the three-dimensional results are compared with those predicted using the quasi-three-dimensional formulation.

Hooper, Steven J.↗
NASA NTRS1974

Analysis and design of advanced composite bounded joints

Advances in the analysis of adhesive-bonded joints are presented with particular emphasis on advanced composite structures. The joints analyzed are of double-lap, single-lap, scarf, stepped-lap and tapered-lap configurations. Tensile, compressive, and in-plane shear loads are covered. In addition to the usual geometric variables, the theory accounts for the strength increases attributable to adhesive plasticity (in terms of the elastic-plastic adhesive model) and the joint strength reductions imposed by imbalances between the adherends. The solutions are largely closed-form analytical results, employing iterative solutions on a digital computer for the more complicated joint configurations. In assessing the joint efficiency, three potential failure modes are considered. These are adherend failure outside the joint, adhesive failure in shear, and adherend interlaminar tension failure (or adhesive failure in peel). Each mode is governed by a distinct mathematical analysis and each prevails throughout different ranges of geometric sizes and proportions.

Hart-Smith, L. J.↗
NASA NTRS1990

A case study in nonconformance and performance trend analysis

As part of NASA's effort to develop an agency-wide approach to trend analysis, a pilot nonconformance and performance trending analysis study was conducted on the Space Shuttle auxiliary power unit (APU). The purpose of the study was to (1) demonstrate that nonconformance analysis can be used to identify repeating failures of a specific item (and the associated failure modes and causes) and (2) determine whether performance parameters could be analyzed and monitored to provide an indication of component or system degradation prior to failure. The nonconformance analysis of the APU did identify repeating component failures, which possibly could be reduced if key performance parameters were monitored and analyzed. The performance-trending analysis verified that the characteristics of hardware parameters can be effective in detecting degradation of hardware performance prior to failure.

Maloy, Joseph E.↗
NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format in structural design of composites

The influence is investigated of a curvilinear fiber format on load carrying capacity of a layered fiber reinforced plate with a centrally located hole. A curvilinear fiber format is descriptive of layers in a laminate having fibers which are aligned with the principal stress directions in those layers. Laminates of five curvilinear fiber format designs and four straightline fiber format designs are considered. A quasi-isotropic laminate having a straightline fiber format is used to define a baseline design for comparison with the other laminate designs. Four different plate geometries are considered and differentiated by two values of hole diameter/plate width equal to 1/6 and 1/3, and two values of plate length/plate width equal to 2 and 1. With the plates under uniaxial tensile loading on two opposing edges, alignment of fibers in the curvilinear layers with the principal stress directions is determined analytically by an iteration procedure. In-plane tensile load capacity is computed for all of the laminate designs using a finite element analysis method. A maximum strain failure criterion and the Tsai-Wu failure criterion are applied to determine failure loads and failure modes. Resistance to buckling of the laminate designs to uniaxial compressive loading is analyzed using the commercial code Engineering Analysis Language. Results indicate that the curvilinear fiber format laminates have higher in-plane tensile load capacity and comparable buckling resistance relative to the straightline fiber format laminates.

Charette, R. F.↗
NASA NTRS1995

Alternative Computational Approaches for Probalistic Fatigue Analysis

The feasibility is discussed for alternative methods of direct Monte Carlo simulation for failure probability computations. First and second order reliability methods are used for fatigue crack growth and low cycle fatigue structural failure modes to illustrate typical problems.

fatigue analysis failure models simulation↗
NASA NTRS1992

Postbuckling failure of composite plates with central holes

The postbuckling failure of square composite plates with central holes is analyzed numerically and experimentally. The particular plates studies have stacking sequences of: (+ and - 45/0/90)(sub 2S); (+ and - 45/0(sub 2))(sub 2S); (+ and - 45/0(sub 6))(sub S); and (+ and - 45)(sub 4S). A simple plate geometry, one with a hole diameter to plate width ratio of 0.3 is compared. Failure load, failure mode, and failure location are predicted numerically by using the finite element method. Predictions are compared with experimental results. In numerical failure analysis the interlaminar shear stresses, as well as the inplane stresses are taken into account. An issue addressed in this study is the possible mode shape change of the plate during loading. It is predicted that the first three laminates fail due to excessive stresses in the fiber direction, and more importantly, that the load level is independent of whether the laminate is deformed in a one-half or two-half wave configuration. It is predicted that the fourth laminate fails due to excessive inplane shear stress. Interlaminar shear failure is not predicted for any laminates. For the first two laminates the experimental observations correlated well with the predictions. Experimentally, the third laminate failed along the side support due to interlaminar shear strength S(sub 23). The fourth experimental laminate failed due to inplane shear in the location predicted, however material softening resulted in a different failure load from predictions.

Lee, H. H.↗