Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Improved Indentation Test for Measuring Nonlinear Elasticity

A cylindrical-punch indentation technique has been developed as a means of measuring the nonlinear elastic responses of materials -- more specifically, for measuring the moduli of elasticity of materials in cases in which these moduli vary with applied loads. This technique offers no advantage for characterizing materials that exhibit purely linear elastic responses (constant moduli of elasticity, independent of applied loads). However, the technique offers a significant advantage for characterizing such important materials as plasma-sprayed thermal-barrier coatings, which, in cyclic loading, exhibit nonlinear elasticity with hysteresis related to compaction and sliding within their microstructures.

Eldridge, Jeffrey I.↗

Towards an Aero-Propulso-Servo-Elasticity Analysis of a Commercial Supersonic Transport

This paper covers the development of an aero-propulso-servo-elastic (APSE) model using computational fluid dynamics (CFD) and linear structural deformations. The APSE model provides the integration of the following two previously developed nonlinear dynamic simulations: a variable cycle turbofan engine and an elastic supersonic commercial transport vehicle. The primary focus of this study is to provide a means to include relevant dynamics of a turbomachinery propulsion system into the aeroelastic studies conducted during a vehicle design, which have historically neglected propulsion effects. A high fidelity CFD tool is used here for the integration platform. The elastic vehicle neglecting the propulsion system serves as a comparison of traditional approaches to the APSE results. An overview of the methodology is presented for integrating the propulsion system and elastic vehicle. Static aeroelastic analysis comparisons between the traditional and developed APSE models for a wing tip detection indicate that the propulsion system impact on the vehicle elastic response could increase the detection by approximately ten percent.

aeroservoelasticity↗

A LOAD-BASED DEPTH-SENSING INDENTATION TECHNIQUE FOR ELASTIC–PLASTIC MATERIAL MECHANICAL PROPERTY EVALUATION

A load-based depth-sensing micro-indentation technique has been developed for material mechanical properties evaluation including elastic modulus, yield stress, strain hardening exponent and stress-strain curve. Based on a Hertzian contact mechanics approach, this load-based depthsensing micro-indentation technique does not require system compliance calibration or the use of high precision depth sensors. Furthermore a unique, material independent, indentation based load-depth algorithm has been developed accounting for both elastic and elastic-plastic deformation of the material beneath the indenter. This algorithm, found to be a function of material yield stress, strain hardening exponent and elastic modulus, is shown to be the basis for obtaining a stressstrain curve. Finite element analyses of multiple materials with various mechanical properties were employed to examine and develop the fundamental indention based relationships between these variables and the load/depth curve needed to extract the stress-strain diagram. In addition, experimental results obtained with this load-based micro-indentation technique were found to yield accurate material mechanical properties (elastic modulus, strain hardening, yield strength) at room and elevated temperatures (up to 1200°C).

36 MATERIALS SCIENCE↗

Low-frequency elastic waves alter pore-scale colloid mobilization

Naturally occurring seismic events and artificially generated low-frequency elastic waves have been observed to alter the production rates of oil and water wells, sometimes increasing and sometimes decreasing production, and to influence the turbidity of water wells. TEe decreases in production are of particular concern - especially when artificially generated elastic waves are applied as a method for enhanced oil recovery. The exact conditions that result in a decrease in production remain unknown. While the underlying environment is certainly complex, the observed increase in water well turbidity after seismic events suggests the existence of a mechanism that can affect both the subsurface flow paths and mobilization of in-situ colloidal particles. This paper explores the macroscopic and microscopic effects of elastic wave stimulations on the release of colloidal particles and investigates the microscopic mechanism of particle release during stimulation. Experiments on a column packed with 1-mm borosilicate beads loaded with polystyrene microspheres demonstrate that low-frequency elastic wave stimulations enhance the mobilization of captured microspheres. Increasing the intensity of the stimulations increases the number of microspheres released and can also result in cyclical variations in effluent microsphere concentration during and after stimulations. Under a prolonged period of stimulation, the cyclical effluent variations coincided with fluctuations in the column pressure data. This behavior can be attributed to flow pathways fouling and/or rearrangements of the beads in the column. Optical microscopy observations of the beads during low frequency oscillations reveal that the individual beads rotate, thereby rubbing against each other and scraping off portions of the adsorbed microspheres. These results support the theory that mechanical interactions between soil grains are important mechanisms in flow path alteration and the mobilization of naturally occurring colloidal particles during elastic wave stimulation. These results also point to both continuous and discrete, en masse releases of colloidal particles.

58 GEOSCIENCES↗

Electrode Elastic Modulus as the Dominant Factor in the Capping Effect in Ferroelectric Hafnium Zirconium Oxide Thin Films

The discovery of ferroelectricity in hafnia based thin films has catalyzed significant research focused on understanding the ferroelectric property origins and means to increase stability of the ferroelectric phase. Prior studies have revealed that biaxial tensile stress via an electrode “capping effect” is a suspected ferroelectric phase stabilization mechanism. This effect is commonly reported to stem from a coefficient of thermal expansion (CTE) incongruency between the hafnia and top electrode. Despite reported correlations between ferroelectric phase fraction and electrode CTE, the thick silicon substrate dominates the mechanics and CTE-related stresses, negating any dominant contribution from an electrode CTE mismatch toward the capping effect. In this work, these discrepancies are reconciled, and the origin of these differences deriving from electrode elastic modulus, not CTE, is demonstrated. Pt/M/TaN/Hf 0.5 Zr 0.5 O 2 /TaN/Si devices, where M is platinum, TaN, iridium, tungsten, and ruthenium, were fabricated. Sin 2 (ψ)-based X-ray diffraction measurements of biaxial stress in the HZO layer reveal a strong correlation between biaxial stress, remanent polarization, and electrode elastic modulus. Conversely, a low correlation exists between the electrode CTE, HZO biaxial stress, and remanent polarization. A higher elastic modulus enhances the resistance to electrode elastic deformation, which intensifies the capping effect during crystallization, and culminates in the tandem restriction of out-of-plane hafnia volume expansion and preferential orientation of the polar c-axis normal to the plane. These behaviors concomitantly increase the ferroelectric phase stability and polarization magnitude. This work provides electrode material selection guidelines toward the development of high-performing ferroelectric hafnia into microelectronic devices, such as nonvolatile memories.

36 MATERIALS SCIENCE↗

Measurement of the Static Nonlinear Third-Order Elastic Moduli of Rocks: Problems and Applicability

The third-order elastic (TOE) model has been used to describe the widely observed nonlinear mechanical behaviors of earth materials. In addition to linear elastic constants ( λ , μ ), three nonlinear elastic moduli ( A , B , C ) are required for isotropic rocks. Contrary to previous research on dynamic TOE moduli, this study followed the protocol to measure strain and stress under uniaxial and hydrostatic compressive tests statically, which were later used to invert for the full set of TOE moduli for four standard rock types with differing pore structures of a porous oolitic limestone, quartz-rich sandstones, and a dense crystalline basalt. The applicability of the TOE model to characterize nonlinearity depends on the fulfillment of path-independence and small-strain assumptions. Using the measured static TOE moduli, the finite element model demonstrates that the stress in the vicinity of the wellbore is more amplified than the stress in the linear elastic case, which leads to a wider zone of rock failure around the wellbore. Due to the long-standing discrepancy between static and dynamic moduli, the rarely reported full set of static TOE moduli is necessary and will benefit future research in understanding the effect of rock nonlinearity on geophysical and geomechanical applications, such as long-term safe storage of CO 2 and generating process of geohazards.

58 GEOSCIENCES↗

Exchange of Alpha Particle in the {sup 16}O+{sup 12}C Elastic Scattering

We have analyzed twenty elastic scattering angular distributions of the {sup 16}O+{sup 12}C system, measured at Sao Paulo Pelletron Laboratory and also data from the literature. The energies cover the region around and above Coulomb barrier, ranging from 8.54 up to 75.43 MeV in the center of mass reference frame. In the {sup 16}O+{sup 12}C scattering, two different processes can occur which result in same exit channel, the elastic scattering and the exchange of an alpha particle between projectile and target. We have used the Optical Model formalism for the elastic scattering and the DWBA to describe the alpha transfer reaction contribution. Thus, by analyzing the {sup 16}O+C elastic scattering at backward angles we have obtained the {sup 16}O{sub gs} alpha spectroscopic factor.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Quasi-elastic scattering and fusion with a modified Woods-Saxon potential

The elastic and large-angle quasi-elastic scattering reactions were studied with the same nucleus-nucleus potential proposed for describing fusion reactions. The elastic scattering angle distributions of some reactions are reasonably well reproduced by the proposed Woods-Saxon potential with fixed parameters at energies much higher than the Coulomb barrier. With an empirical barrier distribution based on the modified Woods-Saxon potential and taking into account the influence of nucleon transfer, the calculated quasi-elastic scattering cross sections of a series of reactions are in good agreement with the experimental data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Fiber Length and Orientation in Long-Fiber Injection-Molded Thermoplastics. Part I: Modeling of Microstructure and Elastic Properties

This paper investigates the effects of fiber length and orientation distributions on the elastic properties of long-fiber injection-molded thermoplastics (LFTs). The corrected experimental fiber length distribution and the predicted and experimental orientation distributions were used in modeling to compute the elastic properties of the composite. First, from the fiber length distribution (FLD) data in terms of number of fibers versus fiber length, the probability density functions were built and used in the computation. Also, it has been shown that the two-parameter Weibull’s distribution can be used to represent the actual FLD. Next, the Mori-Tanaka model that employs the Eshelby’s equivalent inclusion method was applied to calculate the stiffness matrix of the aligned fiber composite containing the established FLD. The stiffness of the actual as-formed composite was then determined from the stiffness of the computed aligned fiber composite that was averaged over all possible orientations using the orientation averaging method. The methodology to predict the elastic properties of LFTs was validated via experimental verification of the longitudinal and transverse moduli determined for long glass fiber injection-molded polypropylene specimens. Finally, a sensitivity analysis was conducted to determine the effect of a variation of FLD on the composite elastic properties.

36 MATERIALS SCIENCE↗

Prediction of the Elastic-Plastic Stress/Strain Response for Injection-Molded Long-Fiber Thermoplastics

This paper proposes a model to predict the elastic-plastic response of injection-molded long-fiber thermoplastics (LFTs). The model accounts for elastic fibers embedded in a thermoplastic resin that exhibits the elastic-plastic behavior obeying the Ramberg-Osgood relation and J-2 deformation theory of plasticity. It also accounts for fiber length and orientation distributions in the composite formed by the injection-molding process. Fiber orientation was predicted using the anisotropic rotary diffusion model recently developed by Phelps and Tucker for LFTs. An incremental procedure using the Eshelby’s equivalent inclusion method and the Mori-Tanaka model is proposed to compute the overall stress increment resulting from an overall strain increment for an aligned fiber composite that contains the same fiber volume fraction and length distribution as the actual composite. The incremental response of the later is then obtained from the solution for the aligned fiber composite that is averaged over all possible fiber orientations using the orientation averaging method. Failure during incremental loading is predicted using the Van Hattum-Bernado model. The elastic-plastic and strength prediction model for LFTs was validated against the experimental stress-strain results obtained for long glass fiber/polypropylene specimens.

36 MATERIALS SCIENCE↗

Frequency, pressure and strain dependence of nonlinear elasticity in Berea Sandstone

Acoustoelasticity measurements in a sample of room dry Berea sandstone are conducted at various loading frequencies to explore the transition between the quasi-static ( f → 0) and dynamic (few kilohertz) nonlinear elastic response. We carry out these measurements at multiple confining pressures and perform a multivariate regression analysis to quantify the dependence of the harmonic content on strain amplitude, frequency, and pressure. The modulus softening (equivalent to the harmonic at 0f) increases by a factor 2–3 over 3 orders of magnitude increase in frequency. Harmonics at 2f, 4f, and 6f exhibit similar behaviors. In contrast, the harmonic at 1f appears frequency independent. This result corroborates previous studies showing that the nonlinear elasticity of rocks can be described with a minimum of two physical mechanisms. This study provides quantitative data that describes the rate dependency of nonlinear elasticity. Furthermore, these findings can be used to improve theories relating the macroscopic elastic response to microstructural features.

58 GEOSCIENCES↗

10-th order of accuracy for numerical solution of 3-D elasticity equations for heterogeneous materials on unfitted Cartesian meshes

We have developed the Optimal Local Truncation Error Method (OLTEM) with 10-th order of accuracy on unfitted Cartesian meshes for a system of 3-D elasticity equations with smooth irregular interfaces. 5 x 5 x 5 = 125-point stencils (similar to those for quadratic finite elements) for elastic heterogeneous materials are used for OLTEM. There are no unknowns at the interface points between different materials; the structure of the global discrete equations is the same for homogeneous and heterogeneous materials. The calculation of unknown stencil coefficients is based on the minimization of the local truncation error of the stencil equations and yields the optimal 10-th order of accuracy for OLTEM on unfitted Cartesian meshes, i.e., the increase by 7 orders in accuracy compared to quadratic finite elements on conformal meshes. A new post-processing procedure provides the 9-th order of accuracy for stresses in the 3-D case. Similar to basic computations it uses OLTEM with the 125-point stencils, the interface conditions and the elasticity equations. It was shown that the use of the elasticity equations for post-processing improves the accuracy of 0.1% stresses by 6 orders compared to post-processing without the use of PDEs. At an accuracy of for stresses, OLTEM with the new post-processing procedure reduces the number of degrees of freedom by 360 - 8000 times compared to quadratic finite elements with similar stencils. OLTEM with the 125-point stencils yields even more accurate results than high-order finite elements with much wider stencils. OLTEM provides accurate numerical results for compressible and nearly incompressible materials.

elasticity equations↗

A new model to simulate the elastic properties of mineralized collagen fibril.

Bone, because of its hierarchical composite structure, exhibits an excellent combination of stiffness and toughness, which is due substantially to the structural order and deformation at the smaller length scales. Here, we focus on the mineralized collagen fibril, consisting of hydroxyapatite plates with nanometric dimensions aligned within a protein matrix, and emphasize the relationship between the structure and elastic properties of a mineralized collagen fibril. We create two- and three-dimensional representative volume elements to represent the structure of the fibril and evaluate the importance of the parameters defining its structure and properties of the constituent mineral and collagen phase. Elastic stiffnesses are calculated by the finite element method and compared with experimental data obtained by synchrotron X-ray diffraction. The computational results match the experimental data well, and provide insight into the role of the phases and morphology on the elastic deformation characteristics. Also, the effects of water, imperfections in the mineral phase and mineral content outside the mineralized collagen fibril upon its elastic properties are discussed.

59 BASIC BIOLOGICAL SCIENCES↗

Differential elastic responses to barrier-altering agonists in two types of human lung endothelium

Vascular integrity is primarily determined by endothelial cell (EC) cytoskeletal structure that is differentially regulated by various stimuli. In this study, atomic force microscopy (AFM) was used to characterize structural and mechanical properties in the cytoskeleton of cultured human pulmonary artery EC (HPAEC) and human lung microvascular EC (HLMVEC) by determining elastic properties (Young's modulus) in response to endogenous barrier protective agents sphingosine 1-phosphate (S1P) and hepatocyte growth factor (HGF), or the barrier disruptive molecule thrombin. Initial studies in unstimulated cells indicate higher baseline peripheral elastic modulus values in HPAEC (mean 2.9 KPa) than in HLMVEC (1.8 KPa). After 30 min of stimulation, S1P induced the highest Young's modulus increase (6.1 KPa) compared to the other barrier enhancing stimuli, HGF (5.8 KPa) and the pharmaceutical agent and S1P analog FTY720 (4.1 KPa). In contrast, the barrier disruptive agent thrombin decreased values from 2.5 KPa to 0.7 KPa depending on the cell type and treatment time. AFM topographical imaging supports these quantitative biophysical data regarding differential peripheral elastic properties in EC. Overall, these AFM studies provide novel insights into the biomechanical properties of human lung EC that regulate vascular barrier function and have potential applicability to pathophysiologic vascular leak syndromes such as acute lung injury. - Highlights: • AFM dynamically measures cellular biophysical properties in live endothelial cells. • Macrovascular human lung EC exhibit different biophysical responses than microvascular. • Agonists that promote EC barrier function increase peripheral elastic properties. • Provide insights into potential therapeutic modulation of human lung EC.

60 APPLIED LIFE SCIENCES↗

Insight into elastic behavior of calcium silicate hydrated oxide (C-S-H) under pressure and composition effect

The present work relates to the study of structural and elastic properties of Tobermorite 11 A as a function of external pressure and composition in terms of calcium to silicon ratio. Basing on the lattice dynamics method, the main aim of this work is precisely to shed light, for the first time, on the high pressure structural phase transition in Tobermorite 11 A and the possible correlation with some elastic quantities. In order to check the transferability of the potentials used we have, additionally, performed a single calculation based on the density functional theory (DFT) for a pressure of 15 GPa in the case of Ca/Si = 1. The variation of the unit cell parameters with pressure indicates that Tobermorite 11 A undergoes a structural instability around 15 GPa along b-axis and around 20 GPa along a-axis which is confirmed from our calculations of X-Rays diffraction patterns at various pressure values. We have also observed the anisotropic character of the Tobermorite structure for both cases (Ca/Si = 1 and Ca/Si = 0.83). Our results show that around 20 GPa an important change appears in the elastic behaviour of Tobermorite. As pressure increases the calculated elastic quantities for Ca/Si = 1 became closer to those evaluated for Ca/Si = 0.83, which may stimulate further experimental and theoretical research on the matter.

36 MATERIALS SCIENCE↗

Phase field benchmark problems for dendritic growth and linear elasticity

We present the second set of benchmark problems for phase field models that are being jointly developed by the Center for Hierarchical Materials Design (CHiMaD) and the National Institute of Standards and Technology (NIST) along with input from other members in the phase field community. As the integrated computational materials engineering (ICME) approach to materials design has gained traction, there is an increasing need for quantitative phase field results. New algorithms and numerical implementations increase computational capabilities, necessitating standard problems to evaluate their impact on simulated microstructure evolution as well as their computational performance. We propose one benchmark problem for solidifiication and dendritic growth in a single-component system, and one problem for linear elasticity via the shape evolution of an elastically constrained precipitate. We demonstrate the utility and sensitivity of the benchmark problems by comparing the results of 1) dendritic growth simulations performed with different time integrators and 2) elastically constrained precipitate simulations with different precipitate sizes, initial conditions, and elastic moduli. As a result, these numerical benchmark problems will provide a consistent basis for evaluating different algorithms, both existing and those to be developed in the future, for accuracy and computational efficiency when applied to simulate physics often incorporated in phase field models.

36 MATERIALS SCIENCE↗

A machine learning approach to determine the elastic properties of printed fiber-reinforced polymers

This work focuses on the simultaneous determination of the elastic constants and the fiber orientation state for a short fiber-reinforced polymer composite by performing a minimum of experimental tests. Here we introduce a methodology that enables the inverse determination of fiber orientation state and the in-situ polymer properties by performing tensile tests at the composite coupon level. We demonstrate the approach for the extrusion deposition additive manufacturing (EDAM) process to illustrate one application of the methodology, but the development is such that it can be applied to short fiber-reinforced polymer (SFRP) systems processed via other methods. Currently, developing composites additive manufacturing digital twins require extensive material characterization. In particular, the mechanical characterization of the orthotropic elastic properties of a composite involves extensive sample preparation and testing, therefore the elasticity tensor is generally populated using a micromechanics model. This, however, requires measuring the fiber orientation state in addition to knowing the constituent material properties. Experimentally measuring the fiber orientation state can be tedious and time consuming. Further, optical methods are limited to resolving the orientation of cylindrical fibers or cluster of non-cylindrical fibers, and computed tomography (CT) methods scan regions of volume that are much smaller than a full printed bead. Therefore, we propose a methodology, accelerated by machine learning, to identify the anisotropic mechanical properties and fiber orientation state at the same time. Early results show that inference of the fiber orientation and composite properties is possible with as few as three tensile tests. Our results show that a combination of the choice of the micromechanics model and reliable set of experiments can yield the nine elastic constants, as well as, the fiber orientation state.

36 MATERIALS SCIENCE↗

Strong effect of liquid Fe–S on elastic wave velocity of olivine aggregate: Implication for the low velocity anomaly at the base of the lunar mantle

The origin of the seismic low velocity zone (LVZ) observed at the base of the lunar mantle is important for understanding the nature of the lunar mantle. Liquid Fe–S is considered as a possible candidate of the cause of the LVZ. However, effect of liquid Fe–S on elastic wave velocity of mantle rock has been considered to be minor, according to theoretical estimation based on the high dihedral angle of liquid Fe–S in olivine aggregate observed in previous microstructural analysis of polished sample cross sections. Here, in this work, we carry out direct measurements of elastic wave velocities of liquid Fe–S-bearing olivine aggregate and report strong reduction of the elastic wave velocities in the presence of liquid Fe–S. The effects of liquid Fe–S in olivine aggregates are much more pronounced than the theoretical estimation. Three-dimensional X-ray microtomography analysis reveals that the geometry of liquid Fe–S strongly depends on the size, with larger liquid Fe–S blobs having low aspect ratios, which may predominantly affect elastic wave velocity. Since smaller spherical Fe–S blobs are much more abundant than the larger elongated blobs, conventional dihedral angle analyses based on scanning electron microscope images tend to statistically over-sample smaller blobs and under-sample larger blobs. Our results suggest that the LVZ at the base of the lunar mantle can be explained by the presence of 4.3–5.0 vol.% liquid Fe–S. The LVZ may be a hidden reservoir of highly siderophile elements (HSEs), which may explain the low abundance of HSEs in the lunar mantle compared to the Earth.

58 GEOSCIENCES↗